Search Documents

By T. P. Smirnoff, R. J. Redmond, K .. N. Murthy

To minimize disruption to the Hollywood District of Los Angeles, a mined station using the New Austrian Tunneling Method (NATM) was developed. This paper presents the key factors contributing to the settlements and dynamic behavior of the unique binocular station design.

Jan 1, 1993

By M. J. Virnig, Peihao Qi, J. Brent Hiskey

The mechanism of gold uptake from iodide solutions by carbon has been investigated. Adsorption isotherms for gold and iodine were established. For activated carbon, approximately 300 mg of gold and 1000 mg of iodine were extracted per gram of carbon at maximum loading. Examination of loaded activated carbon particles by scanning electron microscopy reveals isolated patches of gold deposited on the carbon surface. High-resolution transmission electron microscopy shows that fine gold particles (1-4 nm diameter) are uniformly distributed within the carbon. Iodine was also observed throughout the matrix. The uptake of gold by carbon from iodide solution involves a combined reduction and adsorption process, where the gold iodide species is reduced to the metallic state superficially and adsorbed in the porous structure of carbon. A few experiments for the gold-chloride and gold-bromide systems were carried out for comparison.

Jan 1, 1993

The attachment of a spherical particle to a bubble is theoretically investigated under the condition of a mixed sorption coating of a collector. It is shown that the attachment is determined primarily by the hydrodynamic factor involving the displacement of liquid from the gap between a bubble and a particle. The dependence of the attachment on the state of the surface of particle (sorption coating) is due to a change in the boundary conditions on the interface with water both in the case of surfactant chemical sorption and in that of the physical adsorption of oil. It is demonstrated that at large distances the thinning of a interlayer is facilitated by a physically sorbed collector, while near the bubble this is done by a chemically sorbed one.

Jan 1, 1993

By D Wilson, R R. Vandebeek, R A. Bowes

"As business opportunities are sought around the world, the explosives industry must oftengrapple with the United Nations Transport of Dangerous Goods Recommendations.Canadians have problems in this area that are similar to those of other countries. Thispresentation outlines, through a case study, how a container for shipping ""explosives"" wasdesigned, tested and approved for use by the Chief Inspector of Explosives, the""Competent Authority"" for Canada."

Jan 1, 1993

By D. A. Peterson

Laboratory testing was completed to determine the effectiveness of a fiberglass cable bolt (FCB) as a cuttable rock support for a continuous, hard-rock mining method. The FCB consists of four Polystal tendons combined in a node/antinode fashion, with polyvinyl chloride (PVC) spacers forming the anti-nodes. The largest ultimate pull-out load achieved by the FCB was 22 t (48,400 lb) at 89% of the tendons' theoretical pullout load. This premature tendon failure is accredited to: • differential stresses within the tendons and • differential tendon displacement. An increase in pull-out resistance for a given embedment length is due to: • increased bond area, • reduced interfacial shear and • "wedge" effect. The critical embedment length was found to be 40% less than for conventional steel cable bolts (SCB) at a 127-mm (5-in.) node spacing. An FCB can have up to a 92% increase in load-carrying capacity over a conventional SCB at equal embedment lengths. The load carrying capacity is equivalent to SCB at a 960-mm (37.8-in.) embedment length. Though the FCB is 7.5% more expensive than the conventional SCB (installed), this cost may be offset by increased performance. FCBs are a potentially viable support alternative for continuous hard-rock mining.

Jan 1, 1993

By A. G. Matyas, B. Wasmund, R. C. Francki, K. M. Donaldson

"The construction of large. high-power electric furnaces has been an important factor in the growth of electric smelting technology . New developments in the design and operation of electric furnaces have been spurred by the escalating cost of electric power and increasingly stringent environmental constraints. Key areasofprogress include the application of high voltage to enhance furnace productivity; the installation of novel furnace cooling elements and robust binding systems to extend furnace life; development of process schemes to reduce power consumption by preheating and prereduction of the charge; and environmental control improvements for handling fine dusty feedstocks, and for furnace sealing.This paper reviews these developments and outlines a systematic approach for their application in the custom design of new or retrofit electric furnace facilities.IntroductionThe use of electric smelting furnaces has continued to progress during the last decade. Electric furnaces offer high throughput capacity and productivity. In addition, they produce minimum environmental impact, as the furnaces can be readily sealed, and only a small quantity of off-gas is generated. Electric furnaces present the most favourable choice of smelting technology where high process temperatures in excess of about l400°C are required.Their application is burdened by the escalating cost of electric power, hence it is important to seek new opportunities through further technological development. This paper reviews recent developments in the design and operation of high-power electric smelting furnaces, in the following areas:"

Jan 1, 1993

By Les W. Armstrong, Stephen B. Richardson, Neville T. Moxon

A study was carried out to determine how different degrees of stemming confinement, that is the retention of the explosives gases, effects fragmentation and movement during blasting.

Jan 1, 1993

By M. D. Johnson

The San Andres mine, located in the western mountain region of Honduras, Central America, contains epithermal gold mineralization as disseminations, in quartz-chalcedonic veins and stockworks. Host rocks include a thick sequence of Cretaceous to Tertiary conglomerates, sandstones, rhyodacite tuffs and andesites. Mineralization is controlled by northwest and northeast striking, normal faults and fractures which dip steeply east and west. Currently, 500 STPD of 1. 93 Grams/MT gold ore is being open-pit mined from the conglomerate and andesite. The mine is at the west end of a mineralized zone that can be traced over an area of approximately 1.5 square kilometers.

Jan 1, 1993

By J. Douglas Causey

The Bureau of Mines conducted mineral investigations of the Peace Rock and Deadwood River roadless areas in Idaho, in 1992. Literature research was done by the Idaho Geological Survey. The study areas contain black sand placers (thorium, columbium, tantalum, titanium, uranium, and rare earth elements), gold, and molybdenum prospects. Except for unrecorded placer gold, there has been no mineral production from the areas. No mineral resources were delineated, but a multi-million tonne molybdenum resource is in the Big Pine Creek area and a 142 million m' black sand deposit is in the Stolle Meadows, Peace Valley, and Deadwood River areas. The Deadwood mine produced zinc, lead, and silver. There are six mining districts in and adjoining the areas; Warm Lake, Deadwood, Garden Valley/Lowman, Banner, Summit Flat, and Grimes Pass. Few claims, mostly placer, were active in the study area in 1992. The study areas are underlain by granitic rocks of the Idaho batholith. Most of the deposits are alluvial accumulations of heavy minerals weathered out of the Idaho batholith. Stockwork and narrow veins along shears account for the base and precious metal concentrations. Eleven prospects were examined. Workings consist of drill holes, pits and adits. Geothermal resources (hot springs) occur mainly along the Middle Fork Payette River; Vulcan Hot Springs is a designated Known Geothermal Resource Area. Sand and gravel resources are of local interest.

Jan 1, 1993

By Jeanne A. Zimmer, Andrew B. Cecala, Edward D. Thimons

The Bureau of Mines performed a study to determine optimal locations for longwall face methane monitoring equipment. Longwall face ignitions continue to be a concern to the U. S. coal mining industry. Gains in ignition control technology have been somewhat negated by advances in longwall productivity. More reliable, heavy-duty longwall face systems generate higher production rates and increase methane liberation rates. These rates will likely continue to rise in the future as further coal production increases occur. Efforts will continue in the areas of methane drainage, methane containment, and methane dilution. In addition, more effective face methane monitoring is needed. As technology continues toward automated longwall panels, the importance of monitoring for methane at the shearer becomes even more significant. Since the primary face ignition source is the shearer mining machine, the Bureau ran tests to determine the best location to take methane readings on the shearer. This information, in conjunction with data obtained from field studies, provides a knowledge base for selecting optimum face methane monitoring locations. INTRODUCTION Face ignitions are a concern for many U. S. longwalls and will continue to be until better control technology can be developed or until reliable and accurate knowledge can be provided as to when an explosive concentration is present. Figure 1 shows the number of reported U. S. underground longwall ignitions from 1980 to 1990. The number of longwall panels have remained relatively constant over this time period with 89 reported in 1980, compared to 96 in 1990. In spite of technological improvements in mining over the past decade, no significant reduction in the number of longwall face ignitions has occurred. One factor contributing to this is that the U. S. coal industry is mining gassier seams causing methane liberation rates on the average to be higher (Trevits, 1991; Grau, 1987). Another factor is the development and implementation of more reliable, heavy-duty longwall face systems that are generating higher production rates and higher methane liberation rates. Additionally, the average panel width in 1991 was 714 ft; a 44 pct increase from 1980 when faces averaged a width of 495 ft (Merritt, 1992). Increases in panel width also impact total face methane emissions. [ ] There have been substantial advances in control technology in the areas of methane drainage, methane containment, and methane dilution. In some mines, efforts to drain methane in advance of mining have proven effective, but geological conditions often preclude this approach (McCall, 1984; Ely, 1989). In other cases, ventilation air quantities of over 100,000 ft3/min and face velocities of over 1,000 ft/min have been implemented on longwall panels. Other operations have implemented anti-ignition spray systems which use water sprays behind each cutting bit to quench the hot streaks created from cutting noncoal materials (Courtney, 1990). Other control techniques, such as the modified shearer clearer system and ventilated drum, have been used to increase the amount of turbulence and ventilation around the cutting drums, thus reducing methane levels (Cecala, 1986; Divers, 1987).

Jan 1, 1993

By Chen L. Lin

Scientific visualization is an ideal methodology for investigating complex phenomena that are characterized by large amounts of data. Furthermore, it is invaluable in the study of processes that evolve in time. Scientific visualization relies heavily on computer graphics, image processing and video technologies. Specific applications of scientific visualization in the minerals and materials processing fields that are considered in this paper include: 1) applied CT technology for multiphase materials and minerals, 2) time averaged density profla in air- sparged hydrocyclone (ASH) flotation and 3) dynamic motion analysis of ball mill grinding.

Jan 1, 1993

The solution mining review did not arrive in time for publication in the May issue. The term solution mining is commonly used to refer to heap leaching, dump leaching, in situ mining and bore hole slurry mining technologies. The US Bureau of Mines is continuing with research in these areas. Commercial application of these technologies is progressing. There is an ongoing cooperative research project between the Bureau of Mines and the Santa Cruz Joint Venture to evaluate in situ copper mining at a field site near Casa Grande, AZ. The project is currently in the environmental permitting stage. The Bureau is preparing an environmental assessment for the project as part of the National Environmental Policy Act. The Bureau is also continuing with laboratory experiments to study the leaching characteristics of atacamite ore from the field test site, as

Jan 1, 1993

By N. D. Jagger, I. M. Arbuthnot

Introduction Over the last five years, a large number of small- to medium-sized carbon-in-pulp treatment plants have been built in Australia, most designed to treat between 250,000 t/a and 1.5 Mt/a of ore. Because of the limited capital resources and tight cash-flow positions of these relatively small mining companies, the primary requirement was often to get a plant built and operating in a short period of time and at minimal capital cost. Therefore, since the inclusion of both pre-leach and tailings thickeners represents an obvious and significant capital cost, most of these plants were built without thickeners or even detailed, cost-benefit analyses on their inclusion. In some cases, the increasing use of High Rate Thickeners (HRTs) in the mineral processing industries has, however, resulted in a reassessment, because of their considerably lower cost. This reassessment was triggered primarily by the need to conserve water in arid mining areas where borefields are costly to install and water is limited. With the startup and operation of these installations, the resulting significant savings in cyanide consumption has been recognized, in many situations, as a primary justification for the installation of HRTs. Solution balances Degradation of cyanide occurs in the tailings water discharge to slime dams. The degree of degradation (cyanide loss) in the water recovered depends on a number of factors, but it is usually assumed to be about 90%. The most important mechanisms of CN loss are through HCN losses and oxidation by oxygen in the air, which also assists in the hydrolysis of CN. These mechanisms are supported by the large dam surface area and the long retention time of the tailings water in the dam. By thickening the CIP tailings at the plant and recovering as much tailings water as immediately possible, these losses are avoided. The retention time in an HRT is less than three hours, and the surface area is relatively small. Therefore, CN losses are negligible, which is not necessarily the case in conventionally-sized thickeners. Fig. I shows a block diagram of a 100-t/h gold plant without a thickener. In this example, 50% of the tailings water pumped to the tailings dam is recovered, and the CN concentration of the returned water is 10% of the tailings CN concentration of 150 ppm. Fig. 2 represents a plant with an HRT on tailings, thickening to 55% w/w solids. In this case, the thickened tailings are pumped to the dam, and 25% of the contained water is recovered. The recovered water and the mill make-up water are not sent directly to the mill; instead, they are added to the thickener feed and mixed with it prior to thickening. By doing this, the tailings are effectively washed, and the additional cyanide is recovered. Solution balances over these two circuits show cyanide recoveries of 5% and 65%, respectively. Thus, the thickener use increases cyanide recovery by 60%. Fig. 3 shows a two-stage HRT circuit in a countercurrent decantation (CCD) configuration. In this example, an additional 13% of cyanide is recovered through the use of the second-stage unit. This configuration can be justified when residual cyanide levels are high. Capital and operating costs - Case study 1 Illustrative cost figures are based on a CIP tailings thickener installed, in early 1988, as part of Dominion Mining's treatment plant at Paddy's Flat near Meekatharra. (All costs within this paper, unless stated otherwise, are in Australian dollars.) [Assumptions: Feed rate 150 t/h Ore moisture content 5% Leach density 40% solids Underflow density 55% solids Residual cyanide in tailings 150 g/m3 Flocculant dosage 15 g/t Consumable costs: Water $ 0.40/m3 Cyanide$ 2.00/kg Flocculant$ 4.50/kg Power$ 0.12/kWh Length of tailings pipeline2,500 m Capital costs of the major items involved in the thickener installation are given below: Thickener unit, 15-m diam $ 230,000 Water return pumps 12,000 Water recirculation pumps 28,000 Feed box 5,000 Flocculant make-up system 18,000 Flocculant storage tank and dosing pumps 11,000 Piping and valves 85,000 Electrics and instruments 47,000 Civil works 29,000 Installation 69,000 Total cost$ 534,000] Savings in capital costs that can be attributed to the

Jan 1, 1993

By A. J. Monhemius, R. G. Reddy, G. W. Warren, E. Peters

Thermodynamic solubility of chromium in pickling solutions (i.e., HF- HN03-H2O solutions) was determined as a function of HF and HNO3 acid concentrations at 298K. Pure Cr, AISI type 316 and 416 stainless steel were used in this study. The results showed that the solubility of Cr increased with increase in the concentrations of HF and HNO3 acids in solutions. The solubility of Cr increased in the order of pure Cr > 416 SS > 316 SS. The theoretically calculated Cr solubility data were in reasonable agreement with the experimental data.

Jan 1, 1993

By Randy Fulton, Ignacy Puszkiewicz, George H. K. Schenck

Stuart Olson Construction, Inc. excavated 385m (1263 ft.) long twin tunnels with 6.25m (20.5 ft.) O.D., a portal and a cross-over for the Edmonton, "Metro". The work for Contract No. 76458, SLRT South Tunnel and Portal, in Edmonton, Alberta, Canada was performed in 1989 and 1990. NATM was specified because of the instability of glacial deposits. The contractor decided to use "two firsts" on this project: Fully mechanized NATM and a novel excavator¬mounted tunneling machine. An excavator was equipped with a cutter boom, and a loading and conveying system. This novel machine cost only about one-third of the price of a special NATM roadheader. This new combination of NATM and an excavator-mounted cutter boom offered a cost-effective alternative to shields, slurry TBMs and roadheaders for short tunnels in unstable ground. For NATM tunneling in hard rock or in mixed faces, the roadheader-type cutter boom can be replaced with an impact hammer (hydraulic breaker).

Jan 1, 1993

By R. J. Wesely, Corby G. Anderson, L. Ernest Krys, John B. Ackerman, A. D. Zunkel, Suzzann M. Nordwick

Processing of the refractory precious metal ore from the Sunshine Mine is done in a fully integrated hydrometallurgical facility. This operating philosophy began with the construction of an antimony plant during World War 11, and it continued with the construction of a silver-copper refinery in 1984. The antimony plant relies on an alkaline sulfide ambient pressure leach combined with antimony electrowinning and antimony compound production. This plant is the largest producer of antimony metal in the United States. The one-of-a-kind silver- copper refinery uses a nitrogen species catalyzed sulfuric acid pressure leach system. The plant contains innovative downstream silver recovery processes as well as copper solvent extraction and electrowinning. This paper presents the pertinent process chemistries and flow sheets for the two unique hydrometallurgical processing plants.

Jan 1, 1993

By Ann G. Kim

Fires that occur in abandoned coal mines, waste banks, and in coal outcrops constitute a serious health, safety, and environmental hazard. Toxic fumes, the deterioration of air quality, and subsidence constitute the greatest hazards from these fires. Although tires on abandoned mined land (AML) occur in every coal-producing state, the severity of the problem varies. Methods to extinguish or control AML fires, including excavation, fire barriers, and sealing, are generally expensive and have a relatively low probability of success This U.S. Bureau of Mines report includes information from a variety of sources, i.e., agencies of the Federal Government, State agencies, research reports, conference proceedings, product information, and technical literature. This information has been collated into a comprehensive discussion of AML fire problems. Data on past fire control projects and on the estimated extent of the current problem have been compiled. Factors affecting the occurrence, propagation, and extinguishment of AML fires are discussed. Conventional fire control methods are described, and their probable effectiveness is evaluated. Information on the hazards of AML fires and safety considerations is included. The status of current technology, recent improvements in fire control methods, and areas of current research are discussed.

Jan 1, 1993

By Laurindo De Salles Leal Filho, Arthur Pinto Chaves

The Serrana Process was developed in the 60's to concentrate an igneous low grade phosphate/carbonate ore using tall oil as a collector and corn starch as a modifier in alkaline medium. Nowadays, although tall oil has already been substituted by a new amphoteric synthetic collector, starch hasn't been substituted yet. This study is an attempt towards understanding the role played by corn starch in this specific system. By means of bench scale flotation test, it was observed that corn starch was capable of promoting the flotation of apatite, phlogopite and dolomite. No effect over calcite was observed. The best efficiency of separation apatite/gangue minerals was yielded at the concentration ranges of 17 to 20 mg/l of starch and 13 to 17 mg/l of tall oil. The starch concentration showed a strong influence over the characteristics of the froth produced by the flotation tests, mainly over the volume of the froth and its mineralization.

Jan 1, 1993

By Mike McGill, Steven P. Case, Mark Spaulding

The General Crushed Stone Company at Doswell VA. decided to open a new pit to expand their reserves. The elevation of the property was 136 feet above the present primary crusher. The project required driving twin tunnels under the highway to access the primary crusher from the new property. A shaft was needed to pass blasted rock to the tunnel elevation where it's loaded and hauled to the primary crusher. In addition, a ventilation shaft was required to provide adequate airflow. Dynatec Mining Contractors Inc. Lakewood Colorado was subcontracted to handle the tunnel and shaft development.

Jan 1, 1993

By Timothy J. Rohrbacher

This report presents a U.S. Bureau of Mines study that incorporates coal mining factors, coal recovery factors, and economic factors into the definition of an economically recoverable coal resource. The relationship between these factors to the Energy Information Administration's estimate of U.S. coal resources-the "Demonstrated Reserve Base"-is discussed. The Matewan 7-1/2 minute quadrangle in eastern Kentucky was selected as the initial study area. Results indicate that of the original 1,193 million tons of resource in the quadrangle, only 89 million tons (7.5%) are economically recoverable at a cost of $25 per ton or less. At the current production rate of 5.3 million tons per year, this represents only 16.8 years of remaining reserves.

Jan 1, 1993