Search Documents

By N. Rajmohan, K. T. Jacob

Presented is a thermodynamic feasibility analysis of extracting base metal chlorides from low-grade, multi-metallic oxide ores using CaC[1]2 as a chlorinating agent in the presence of SO2 and O2. The oxides react to form corresponding chlorides, while CaC[1]2 is converted to CaSO4. The Ellingham diagram is used for comparing the standard Gibbs' free energy change for the sulfation-chlorination reaction of a large number of oxides. Except for alumina, silica and chromia, most of the other metal oxides will be converted to their respective chlorides. The volatile chlorides can be condensed, and the chlorides present in the condensed state can be leached. A process is proposed that uses a nontoxic chlorinating agent and gives an efficient separation of the metallic values from the gangue.

Jan 1, 1993

By Robert A. Jankowski, George E. Niewiadomski

INTRODUCTION The utilization of longwall mining technology in the United States has steadily increased since the first longwall plow system was installed in 1952. At the errs of FY 1992, some 76 coal mines were employing longwall mining systems for coal extraction, and approximately 78 shearer and 3 plow faces are operating nationwide at any given time. Although the number of operating longwalls has remained relatively constant over the last five years, longwall production levels have increased significantly during this period. During the same timeframe, the number of continuous miner sections has decreased by 13 pct., from approximately 1438 in FY 1988 to less than 1250 in FY 1992. According to Mine Safety and Health Administration (MSHA) data, the average production of longwall sections increased from approximately 2400 tons per shift (tps) in FY 1988 to more than 3100 tps FY 1992. In fact, the average production has more than tripled since 1978, when it was only 850 tps. Approximately 25 pct. of operating longwalls are capable of producing in excess of 4000 tps. Longwall production currently accounts for nearly 36 percent of U.S. underground coal production, compared to 4 pct. in 1978. These improvements are attributed to improved longwall equipment and increased availability, larger longwall panels and automation. While longwalls are highly productive and offer other advantages, operations employing this method of mining continue to experience dust compliance problems more frequently than other mining system. Although dust levels have remained relatively unchanged over the past five years, averaging 1.6 mg/m3 and 1.9 mg/m3 based on results of operator and inspector sampling, respectively, during FY 1992, approximately 25 pct. of the operating longwalls were in noncompliance during any given bimonthly sampling cycle. Although modest gains in longwall dust control technology have been made, these have been overshadowed by significant increases in production rates. As more coal is mined, more dust is generated (Figure 1). Therefore, the increase in longwall productivity has meant that far more dust is being produced which must be controlled. [ ] In view of the current compliance record, any efforts to further increase longwall output, as has been forecasted, must be accompanied by: (1) the reduction of dust levels at existing operations through the proper installation and maintenance of suitable engineering dust controls; and (2) the advancement of dust control technology for today's and future longwalls that will enable all face personnel o work in an environment that is free of excessive levels of respirable coal mine dust. MSHA'S RESPIRABLE DUST CONTROL PROGRAM Since 1972, federal regulations have required each coal mine operator to continuously maintain the average concentration of respirable dust in the mine atmosphere during each shift in the active workings at or below 2.0 mg/m3 through the application of environmental dust control methods. The regulations provide for further reduction in the dust standard whenever the

Jan 1, 1993

By J. C. Kerkering, S. M. Miller, P. C. McWilliams

Researchers at the U.S. Bureau of Mines investigated the use of close-range photogrammetry and subsequent stereo digitizing to obtain data from rock fracture roughness profiles. The photogrammetric process yielded results that were acceptable but somewhat inferior to those obtained by a mechanical profilometer. On the basis of this study, further pursuit of photogrammetry as a data collection method in mining is proposed. Fractal geometry was investigated as a means of measuring the roughness of rock fracture profiles. Four fractal algorithms were used: divider method, modified divider method, box method, and spectral method. A comparison of the methods gave ambiguous results. Brown's modified divider method provided the best means of obtaining the fractal dimension. Shear strength estimates were obtained using the parameters of the modified divider method and Myers' Z, measure. Because of differences in results when comparing the different ways of obtaining the fractal dimension, future users of fractals in studies of rock fractures are advised to cross-check their results carefully.

Jan 1, 1993

By G. P. Larson

We define a specialized mineral market as follows: Specialized markets occur where a low volume of a given mineral is used to convey a large benefit to a specific product. Sales of these value added minerals to small markets generally require a different marketing approach than bulk or commodity markets for traditional minerals. Specialized markets are differentiated by several characteristics as listed in Table 1. [Table 1-Characteristics of Specialized Markets 1. Long-term sample evaluation 2. Small volume markets 3. Highly controlled properties 4. Customized specifications 5. Technical selling effort] Many of the specialized markets require long term evaluations before sales can be made. This can vary greatly depending on the type of industry and ultimate end-use of the final product. In some cases, complete evaluations may take from several weeks to years. Length of sample evaluation has no relationship to size of market. That is, the total market may be quite small or fairly large (e.g. from a few hundred pounds to a few million pounds). Uniformity of value added minerals from lot to lot is an extremely important characteristic for these markets. Variations that are of no consequence to one industry (or application) cannot be tolerated in another. This has led to customized specifications and test procedures for specific markets and applications. Because of the greater uniformity and customized specifications, the need for greater technical selling effort is required. This is particularly true in the initial developmental phases and contacts as well as in maintaining the account after the initial order. A small entrepreneurial organization can be used to advantage to achieve goals of sales and profit to these types of markets. The large commodity or bulk producer's sales and marketing organizations are not ordinarily equipped to give the necessary service or technical assistance to the specialized markets. The organization usually required for this type of marketing is given in Table 2. [Table 2- Specialized Marketing Organization Requirements 1. Flexible approach to technical and marketing problems 2. Versatile background in a broad range of industries 3. Laboratory backup when necessary 4. Marketing expertise 5. Technically competent management] In developing specialized markets, a flexible approach to both technical and marketing problems is necessary in understanding the needs and requirements of the industry and the applications involved. This flexibility is also helpful in adapting existing products to new market areas. Having knowledge of a range of industries as broad as possible can be very helpful. It often happens that a product developed in one area or industry can lead to its application in a different area with excellent results. Laboratory assistance for a wide range of tests and test procedures is an important asset in any development program for specialized markets. Laboratories can also assist in competitive evaluations. Marketing expertise and a management with some degree of technical understanding are necessary in to assign proper cost/ benefit ratios to a proposed new product or application of existing products. This is important since the total market volume can be small and the time required for initial contact to first sale can often be lengthy. Also, management's technical and marketing expertise is required in evaluating all possible options that can be considered viable when an application is presented. Once an organization of this type is in place, it is then possible to determine the needs of the marketplace, including when various minerals might have to be customized to fill those needs. There are generally two methods of marketing, as noted in Table 3. [Table 3- Method of Marketing 1. Product Driven -Develop a product with certain desirable properties and try to find a market to utilize those properties. 2. Market Driven -Know market well enough that when a need arises, it is possible to identify a product that will satisfy the need.] These approaches are not mutually exclusive and can be used at the same time. Marketing a value added mineral generally requires the "market driven" approach. Hence, the importance of a knowledgeable management as outlined above. To determine where needs and opportunities exist, several approaches can be used. Table4 lists some of the methods employed.

Jan 1, 1993

By Shinnosuke U, Zhang HE, Qian X

In this paper it is recommended that pyrite is to be separated as froth from arsenopyrite by selective depression of arsenopyrite in strong alkaline medium (1), by oxidation with chlorinated lime (II), by co-use of chlorinated lime with sodium carbonate (III), and by modification with `L' reagent (know-how) without filtering to get rid of residual copper ions after Cu activation (IV). The corresponding principles of these (new) effective methods were briefly discussed. The artificial mixture (1:1) of pyrite and arsenopyrite could be successfully separated, and concentrates of pyrite containing 2.12 per cent (I), 7.00 per cent (II), 2.60 per cent (III) and 3.16 per cent (IV) arsenic with recovery of 90.9 per cent (1), 89.5 per cent (II), 89.0 per cent (III) and 81.4 per cent (IV) respectively can be obtained by only one flotation. Some effective precautions were suggested to improve the separation of arsenopyrite and pyrite (or other sulphides) by flotation.

Jan 1, 1993

By R. L. Grayson, R. C. Althouse, L. A. Layne, M. J. Klishis

Introduction The researchers combine a detailed microanalysis of accident data and roof bolting field observations to develop new and meaningful risk indices for the roof bolter job classification. These indices incorporate information that has not been used in traditional measures of risk. The significant parameters that these new indices incorporate are the total number of accidents occurring within a particular work activity, the amount of time a miner usually spends performing the work activities in which the accidents occurred, and the average severity of the injuries incurred in the accidents. Being specific for a particular job, they aid comparisons among work tasks performed in the bolting cycle. The indices' specificity provide anew basis for reexamination of training and operational development of miners for specific jobs. Microanalysis The roof bolting microanalysis was performed by examining the empirical data and written summaries for all bolting accidents reported in the West Virginia Safety Information System (WVSIS) for the years 1983-1987. The WVSIS database contained more than 15,000 accident narratives. The microanalysis of bolting accidents covered 2083 reported personal injuries (RPIs). This large number of injuries, performed at an industry-wide level, provides a broad picture of the nature of roof bolting injuries. The analysis focuses on the activities associated with the cyclical routines of the roof bolting process. For this analysis, roof bolting tasks were categorized into work routines based on the sequence of work activities performed by roof bolters. Four work routines were identified within the overall bolting cycle. And these routines comprised 70% (1217) of all roof bolting accidents at the face. The routines include: face area preparation; tramming, positioning and setting the automated temporary roof support (ATRS); drilling holes; and installing bolts. The types of injuries most common within a routine and the average severity of those RPIs were also identified. Table 1 gives a breakdown of the percentage of accidents by the bolting routines. Another 19% of the roof bolting RPIs cannot be classified in a particular routine because of the vagueness of the narratives. However, it was clear that these accidents involved drilling holes or installing bolts. These results are consistent with previous research. It identified drilling and bolting, followed by tramming, as the most frequent sources of injuries (Helander, Krohn & Curtain, 1983). [Table 1-Accidents by bolting routines at the face Accidents Bolting routine Percent Number Face area preparation 18.2 222 Tram, position, ATRS 23.3 284 Drilling holes 34.2 416 Installing bolts 24.2 295 Total 1217] Roof bolter operators were involved in 82% (1706) of the 2083 accidents. The RPIs incurred by classified roof bolters occurred largely on working sections (95%) and at the face area on the working section (75%). Approximately 23% of the 1706 roof bolter RPIs occurred during tasks which were not part of the bolting cycle. These included belt utility work, providing supplies and section moves. Miners in other job classifications who were involved in roof bolting accidents accounted for the remaining 18% of the 2083 roof bolting RPIs. Among this group were section utility men and general laborers (41%), section machine operators (38%), and electricians and mechanics (11%). Another 9% were performing on-section supervisory functions. Face area preparation Face area preparation work led to a substantial number of injuries, although it accounted for the lowest number of injuries of the four routines. Several tasks were associated with the injuries incurred in this routine. Table 2 shows the percentage of injuries associated with face area preparation. [Table 2- Accidents occurring during face area preparation 26.6% Setting temporary and supplemental supports 24.8% Scaling roof and ribs 21.2% Installing ventilation devices 15.8% Handling supplies and materials 11.6% Miscellaneous tasks] The injuries commonly involved overexertion and 'struck by' falling coal and rock. Handling materials often led to overexertion injuries. Nearly 66% of the scaling-related injuries and about 33% of the injuries incurred during the setting of temporary supports involved 'strikes' by equipment, materials, top and rib. Tramming, positioning and setting the ATRS During tramming operations, workers were often struck by components of the machine and hit by loose roof and rib. Poor footing also led to slips, sometimes against the moving machinery. Table 3 gives a breakdown of accidents in this routine. Control levers were a significant problem in this routine.

Jan 1, 1993

By William J. Maloney

OVERVIEW Blind drilled shafts are becoming increasingly popular, particularly in the Appalachian coalfields, as a secondary and sometimes primary means of ventilation. The reasons for the rebirth of the blind shaft are mainly due to it's economics, timeliness, safety characteristics and inherent independence from underground operations. Historically blind drilling has been used to a limited degree in hard rock and tunneling ventilation. With the recent advances in cutters, bit design, equipment and lining systems, particularly in the Appalachian coalfields, blind drilled shafts are once again the shaft construction technique of choice to the educated ventilation specialist. [ ] HISTORY OF BLIND DRILLING Blind drilling has it's roots in numerous places, including the Nevada Test site, the coalfields of Appalachia and Germany along with the uranium mines of Arizona. Early technology was developed using a variety of equipment mainly of oilfield origin with oilfield drillers entering the industry on a project basis only to "pull in their horns" and return to the oil patch. Shafts completed by oilfield equipment range from the shallow 5' and 6' lined shafts on the Nevada test site to two (2) 10' lined, 730' deep shafts in Alberta for heavy oil development. Several of these shafts were completed to extraordinary depths with the record being a 90" diameter, 6,150' deep shaft being completed in the Aleutian Islands of Alaska in 1969. EQUIPMENT Oilfield equipment is still being used on the Nevada test site but elsewhere specialized blind hole equipment has been developed to enhance the efficiency of particular applications. Where steel liners are required the A-leg derrick with a simple hoist and rotary system is used. The largest user of this type equipment in the world is the former USSR where blind drilling for mine ventilation is the norm. On applications where trip time and cutter changeout are a priority, top drive hydraulic rigs have been developed which are highly automated, efficient and mobile. These rigs are particularly well suited for tunneling applications where shafts are shallow and sites are usually tight.

Jan 1, 1993

By Floyd C. Bossard

A method of hand-calculating the air-cooling requirements of a conceptualized underground mining operation is presented for the reader's orientation. Separate air heat load calculations were conducted for adiabatic compression, electromechanical equipment, wallrock, broken rock, groundwater, and blasting operations. The air heat sources were calculated for four mining levels under conditions representative of a typical planned mining operation at depth. The total heat gain on each level will approximate the level air-cooling requirements. The results of these hand calculations can be further modified by the use of mine ventilation computer software that refine the heat-source calculations, predict underground ambient air temperatures, and establish the air-cooling requirements of a mine. INTRODUCTION The principal mining method employed is a modified vertical crater retreat (VCR) blasthole operation. Typical scopes range from 20 to 40 feet wide, 75 to 100 feet long, and 100 feet in height. Six and one-half inch blastholes are drilled with an "in the hole" hammer drill. Eight-foot high horizontal rounds are blasted down. Mucking of ore from the undercut to orepass is done with LHD equipment operated from a remote control station. Backfill includes hydraulically placed tailings with cement, and waste rock when available. Stope access is from ramp sub-levels on 50-foot vertical intervals. Crosscuts are ramped down to the first stope cut 25 feet below the sub-level elevation. Then the crosscuts are raised by taking down the back when each stope cut is completed, until an elevation 25 feet above the sub-level is reached. The crosscuts are filled with tailings, and/or waste rock. See Figure 1. Typically, a two-pronged approach to defining the air-cooling requirements is conducted. First, the principal sources that make up the air heat load are individually hand-calculated. Second, projections of mine heat load are calculated by utilizing computer modeling techniques. This paper discusses the first method (hand calculations) of determining the individual components of heat flow into the mine. CALCULATED AIR HEAT LOADS Adiabatic Compression The plans for the mine include delivery of 300,000 cfm of air to ventilate the lower level operation. This is equivalent to approximately 200 cfm/ton of rock produced (300,000 cfm/1500 tpd of ore and waste). As air flows down a shaft, with no heat interchange between the shaft and air and no evaporation of moisture taking place, the air is heated in the same way as if it were compressed in a compressor. Dry air increases in temperature about 5.4°F per 1000 feet. One BTU is added to each pound of air for every 778 feet of decrease in elevation, or is subtracted for the same elevation increase. For dry air, the dry-bulb temperature change is 1/(0.24 x 778) = 0.00535°F/ft., or 1°F/187 ft. elevation. Auto-compression may be masked by the presence of other heating or cooling sources, such as shaft wallrock, groundwater, air and water lines, electrical facilities, etc. The major factors influencing the temperature of the air delivered underground by a shaft are (1) the night time cool air temperature's effect on the rock or lining of the shaft, (2) temperature gradient of ground rock related to depth, and (3) evaporation of moisture within the shaft which increases the latent temperature and decreases the sensible temperature. [Calculation For Adiabatic Heat of Compression] a. Assumptions: 1. Three hundred thousand cfm of fresh air at 3000 level has increased in temperature during the summertime to the point where it has little available cooling power. Air-cooling will be required on 3000 Level and below. 2. Elevation of 3000 Level is approximately +1000 ft. above sea level.

Jan 1, 1993

By E. Oshima

The only one reverberatory furnace smelting in Japan has been alive in Onahama Smelter, Onahama Smelting and Refining Company. The fuel for the reverberatory furnaces had been changed from bunker C-oil to mainly coal and partially waste tires to reduce the energy cost. The steam, recovered by the waste heat boilers of the reverberatory furnaces, has been utilized fully for the power generation to save the purchase power. Copper concentrate has been smelted also by injection through tuyeres in the P.S. converters since 1983. The amount of concentrate, treated in the converters, was increased by the construction of small oxygen plant in December, 1990. In the paper, the current practice and improvements in the reverberatory and converter operations are described.

Jan 1, 1993

By J. L. Sanchez

Using a special double-zone transpiration reactor, the vapor transport chemistry of vanadium pentoxide in the presence of water vapor has been investigated. Three possible volatile hydroxides above V,O,(s) are reported in the literature: VO,(OH),, V,O,(OH),, and VO(OH),. In the present study, it was established that VO(OH), is the principal gaseous hydroxide species formed. The predominant reaction was found to be: { } The vapor pressure of VO(OH), was measured as a function of temperature, water pressure, oxygen pressure and flowrate. The results have been used to determine the Gibbs free energy of the above reaction as a function of temperature: { } The results of the present work were combined with thermodynamic data reported in the literature to obtain expressions for the AGO for the reaction above V,0,(1) and the AGO of formation (units in cal/g-mole).

Jan 1, 1993

Refractory gold ores have been the subject of intensive metallurgical study in order to achieve more efficient recovery of contained values and at the same time to minimise environmental impact. Considerable innovative gold processing technology was introduced in New Zealand last century, the most notable being the first successful commercialisation of the cyanidation process by the Crown Mines Company at Karangahake in 1889. The Karangahake gold-silver deposit was second only +to the Waihi Martha mine in total bullion production from the region with active mining from 1882 until about 1920 and sporadic production between 1930 and 1944. Reevaluation at Karangahake with associated metallurgical testing has continued since that time becoming particularly active in the last decade as a result of increasing gold prices. Gold processing technology is reviewed and results of some recent test work are presented and discussed in the context of Karangahake history and future development possibilities. This work confirms the variability and complexity of the Karangahake deposit both mineralogically and metallurgically and suggests flotation followed by new and innovative smelting is the most appropriate processing route for the recovery of gold from the high grade ore which could be produced from the Karangahake workings in moderate tonnages.

Jan 1, 1993

By J. E. Gebhardt, D. A. Rice, P. E. Richardson

An improved understanding of the significant role of electrochemical reactions in sulfide flotation has evolved in the past 20 years, This understanding has been accompanied by a corresponding increase in attempts to control the electrochemical potential of flotation pulps for monitoring and controlling sulfide flotation circuits to improve metallurgical performance. This paper discusses the basic electrochemistry of sulfide flotation and the use of electrochemical potential as a control parameter.

Jan 1, 1993

Maintaining high carbon activity is vital to the efficiency of any Carbon-In-Leach or Carbon-In-Pulp process. Reduced activity can lead to longer residence times or gold losses in the tails. Regenerated carbon from the CIL circuit at Macraes Gold Mine was analysed for kinetic activity and composition over a 15 month period. An increase in kinetic activity during the time period was recorded, which was linked to reduced Na and Ca loadings. A laboratory simulation of the loading, stripping and regeneration of gold was developed and tested. Kinetic activities were obtained for synthetically fouled carbons following three circuits of the laboratory simulation. It was shown the competitive gold adsorption ability of xanthate fouled carbon (previously reported as a serious deactivator) could be significantly recovered following effective thermal regeneration. This ability was maintained in a subsequent circuit loading.

Jan 1, 1993

In the 100 years since the formation of The Australasian Institute of Mining and Metallurgy there have been significant changes in all aspects of the mining industry.A number of the changes have been driven by technical evolution or necessity, others have been driven by developments in the application of the products produced from the mining of minerals. Other changes have been driven by shifts in community values.

Jan 1, 1993

By R. Tessier, R. Grant, C. Bazin

"Brunswick Mining has investigated grinding media optimization for the purpose of improving the flotation feed and regrind product size distributions to enhance metal recoveries. The paper presents findings in the on-going testing of various sizes and shapes of grinding media. Breakage rates are used as an aid to assess the effect of grinding media. Results of empirical and phenomenological analyses demonstrate the importance of adequate selection of media sizes on the milling operation.INTRODUCTIONBrunswick Mining and Smelting operates one of the world's largest lead and zinc mine near Bathurst, New-Brunswick. The No. 12 ore body is an extremely fine grained volcanogenic massive lead, zinc, copper, silver, iron sulphide body between two metamorphosed sedimentary and felsic volcanic rock units. Pyrite content is about 60% with 20% non-sulphide minerals, mainly silica and chlorite. The operation is currently processing 10,500 tonnes of ore per day in conventional crushing, grinding, differential flotation and dewatering circuits. Details on the circuit can be found elsewhere (e.g. Hendriks and Ounpuu, 1985; Grant et al., 1991).The mill has operated for more than 25 years and despite the past milling experience, there has been much disagreement as to the required grind size. Since 1964, fineness of the flotation feed ranged from 60% to 80% passing 400 mesh (37µm) and averaged slightly over 71%in1992. Results from mineralogical analysis (Petruk and Schnarr,1981; Coleman, 1988), Brunswick metallurgical laboratory (Grant et al., 1991; Shannon et al., 1992) and Lakefield pilot plant tests (Hendriks, 1984; Hendriks and Ounpuu, 1985) clearly indicate that improved metal recoveries can be achieved by an increase in the fineness of grind, and more specifically by maximizing the amount of material in the 15-25µm range."

Jan 1, 1993

By Randall D. Peterson

Economic operation of a mine ventilation system must include some means by which operating costs can be quantified and evaluated periodically. Current practice at most mines relies upon the best judgement of foremen, engineers and managers to identify high cost or problem areas in the system and to estimate potential costs and benefits of work proposed to reduce inefficiencies. The problem with this is that significant savings can be overlooked or sub-economic projects may be undertaken when sufficient attention is not paid to the interrelationship between airflow characteristics and corporate financial criteria. In order to accurately determine costs and benefits it is necessary to view the solution of each potential ventilation problem as a separate economic opportunity.

Jan 1, 1993

By Odd G. Askilsrud, Steinar Johannessen

New powerplants, tunnels and dams are currently under construction at Meraaker to triple the annual power production of a nearly 100 year old power scheme. A total of 44 km tunnels with cross sections varying from 7 m2 to 32 m2 have been excavated in hard rock formations. Ten kilometers were excavated by a High Performance Tunnel Boring Machine (HP TBM). The remaining tunnels have been completed by the drill and blast method, using modem proven equipment and procedures. This paper gives special attention to the TBM drive and equipment selection, including, planning, site organization and performance.

Jan 1, 1993

By Albert E. Ketler

The AirBoss*200 is a unique ambient airflow sensor with important improvements in accuracy, especially in the critical low end, 0-61 m/min (0-200 fpm) where MSHA regulations apply. All solid state, its design is rugged, and there are no moving parts or delicate filaments. An on-board microprocessor calculates air velocity, linearizes and corrects for temperature, while driving voltage and current loop analog outputs to .3 meters/minute (1 ft/min) resolution. Recent developments also cover both positive and negative flow directions. A hand held computer is available to readout data and to adjust stored range selection, alarm set points, calibration data and the speed of response. Installation in hazardous areas is covered by MSHA Classes G, H and L.

Jan 1, 1993

By J. Harrison Daniel

Increasing concerns of industrial hygiene and worker health issues and resulting regulatory actions, coupled with continuing advances in mining systems, are placing new burdens on the industry and Federal Government; particularly, mine ventilation departments. More encompassing worker health programs are required to respond to Federal promulgation of regulations and to keep abreast of techno- logical advances in the mining industry. The relationship between the mining industry and Federal agencies involved in rulemaking is presented, along with the rationale of an Industrial Hygiene Management Plan. This plan or strategy focuses on developing partnerships and collaborative research groups to address the controversial health issues facing not only the mining workforce, but our society.

Jan 1, 1993

By M. J. Virnig, Christopher A. Fleming

THE CIP PROCESS "IN THE RIGHT PLACE AT THE RIGHT TIME? After its tentative introduction to the precious metals mining industry in the earlier part of this century, the carbon in pulp (CIP) process has now come of age, and is the process of choice on all new gold mills. Well over 50 percent of all gold that is mined each year is recovered by adsorption on activated carbon, and the percentage will increase in the years ahead, when old mills using Merrill Crowe technology come to the end of their lives, and as the proportion of world gold production from low-grade resources increases. The pioneering process development work in this field, which was mainly concerned with carbon elution, was carried out by Zadra and his colleagues at the United States Bureau of Mines in the early 1950's (Zadra et al., 1950, 1952), and led to the commissioning of the first large-scale, industrial CIP plant, at the Homestake Mine in South Dakota, in 1973 (Hall et al., 1974). From there, the process spread rapidly, firstly in South Africa in the late 1970's. and then throughout the rest of the gold producing world in the 1980's. There were several factors that led to the meteoric (by gold industry standards) acceptance and successful implementation of this new technology into gold processing operations worldwide. Firstly, and perhaps most fortuitously, the development of the technology closely paralleled the 1968 release of the gold price from the rigid constraints of the $35/oz. gold standard. With the value of the metal allowed, for the first time in modern history, to fluctuate in response to free market supply and demand forces, the gold industry witnessed an unprecedented boom as the price of their commodity increased ten-fold in a remarkably short period of time. This had several important spin-offs as far as new process developments were concerned: The profits realized by established gold-mining companies increased enormously and, consequently, there was more to spend on research and development and exploration for new deposits.

Jan 1, 1993