Search Documents

By Richard D. Begley

This paper summarizes the development of a mechanistic model to predict longwall mining induced surface subsidence. The model was originally developed from data acquired from a recent field study conducted in Northern West Virginia. Additional data has been collected from published sources and used to refine the model. The original model utilizes a negative exponential equation to predict the subsidence profile after the maximum possible subsidence is predicted based on the following input parameters: mine geometry, angle of draw and expansion factors for the deformation zones that have been identified above a longwall excavation. The model refinement involved the development of relationships between physical properties of the overburden strata and angle of draw in addition to the expansion or bulking factors. Therefore the refined model now requires only mine geometry and a typical geologic column from the site to predict the subsidence profile. This paper provides the methodology that enables the model to determine the angle of draw and expansion factors breed on physical properties of the site geology i. e. percent of strong rock and Rock Quality Designation of the overburden strata. In addition :comparisons of predicted results with measured data for over H) different sites with various geological and geometrical parameters located throughout the United States will be presented.

Jan 1, 1989

The South Wall Base Case Design for Mt Whaleback indicated that along portion of the South Wall a cigar shaped synclinal keel, contain- ing 14 800 m', of Dales Gorge Member ore, would be unkeyed and bed- ding undercut. The dry "ore lobe" slope would be 60m high, unbenched and approximately 170 m long. Stability analyses using specific design parameters established that artificial reinforcement could stabilise the slope and be economically justifiable. To implement the slope design reinforcement for such a complex geo- logical structure it was necessary that all functions pertaining to slope excavation be integrated and co-ordinated within the Mine Geotechnical Section. The objective being to minimise slope damage and thereby optimise the effect of design reinforcement. The successful excavation of the ore lobe in 1988, three years after the introduction of artificial reinforcement, was achieved by strictly main- taining the following parameters. 1. Accurate Geological Model 2. Controlled Perimeter Blasting 3. Controlled Excavation Techniques 4. Quality control -Reinforcement Installation 5. Additional Reinforcement.

Jan 1, 1989

By John Nadolski

Intensive hydrologic monitoring of the Powder river basin has been on-going since the early 1970's. Data were used in environ- mental assessments and for determination of hydrologic consequences associated with coal mining activities. For most coal mine operators, data collection has continued in this baseline mode with little or no statistical analysis of the data and with no statistical procedure established to detect changes in groundwater quality. For the past four years Powder River Coal Company has studied several statistical techniques to analyze groundwater quality. Three objectives were pursued: 1) to determine the baseline water quality for key aquifers; 2) to determine which wells could be deleted from the monitoring program without reducing monitoring effectiveness; and 3) to define a statistical test to determine water quality changes. Knowledge of the regional geo-hydrologic system was combined with an analysis of the water quality monitoring in order to identify homogeneous aquifer zones. All wells within an aquifer zone were treated as one population, and a t-test was used to determine the minimum number of samples needed to define the water quality for each aquifer zone. Results indicate that the data for each aquifer zone were nor- mally distributed and that groundwater quality could be defined using a fairly small number of samples. Because of the minimum sample size test, groundwater quality sampling was reduced by between 75 and 85 percent.

Jan 1, 1989

Eliminate the occurrence of false fire detection alarms caused by the operation of diesel-powered vehicles in underground coal mines. Approach Fire detection systems used in underground mines are based on measurements of airborne combustion products such as carbon monoxide or smoke particles. The effectiveness and credibility of these systems can be reduced by the occurrence of false alarms that result from the operation of diesel-powered equipment, which produces the same combustion products. False alarms end up being very costly to the mine operation in terms of downtime and labor needed for verification. To improve upon current fire detection systems used in the presence of internal combustion engine products, the U.S. Bureau of Mines developed a fire detector that can discriminate between the occurrence of real mine fires and the presence of engine smoke.

Jan 1, 1989

By Khamis Y. Haramy

This paper summarizes ground control studies of longwall panel entry systems in two Western U.S. coal mines. Presented are comparisons of in situ pressure change measurements and assessments of chain pillar and entry behavior under a wide range of cover. Results indicate that no one entry system design is universally applicable, and that site-specific factors need to be considered for panel entry design. Relationships between overburden depth, face advance, and magnitude and location of the forward abutment are discussed for western operations. In addition, analysis indicates that use of yield pillars may reduce or eliminate some stress-related problems that plague longwall panel entry design.

Jan 1, 1989

By P. Ventura

Reliability of the liquefaction analysis is based on data plotted as by piezocone, as by deep vibrocompactation monitored tests. The negative porewater pressure, re lated to hydrostatic value, recorded by piezocone, is a good marker of the absen ce of the liquefaction. Systematic measures of the ground settlements, inside the vibroinfixed steel pipe, allow to locate the liquefable strata with loose density. Experimental study of the combined soil improvement by stone columns is carry out in particular in sea bed. The interaxis of the columns for the best efficiency is valued as of the vibrocompactation, as of the drainage effects, especially during earthquake.

Jan 1, 1989

By Ava Walker

The first form of a surety bond was an honest handshake between two or more parties agreeing to a decision, and their personal guarantee of following through to completion. This has all changed. In 1895, the United States Treasury Department disclosed that $35 million worth of personal surety guarantees on file had become worthless. A law was then passed requiring all surety bonds, in favor of the United States, must be corporate surety bonds. Today, a surety bond is one of the nation's leading fi¬nancial instruments used to guarantee the completion of an obligation. One hundred-fifty years before cor¬porate surety bonds, outcrops near Richmond, VA, were being mined. These surface mines became under¬ground mines. Today, both are still being used to obtain a leading energy source, coal. Since that time, more than 5956 km2 (1.47 million acres) of coal mined lands have been reclaimed in the US (Coal News, August, 1987). More than 25,000 state and Federal mining permits cover¬ing 14,164 km2 (3.5 million acres) have been issued during the last 10 years. Coal production has exceeded 7.2 Gt (8 billion st). More than 5665 km2 (1.4 million acres) of mined land has been reclaimed by active coal mining opera¬tions and 267 km2 (66,000 acres) of abandoned mined lands have been re¬claimed by others. Reclamation bonds were freely writ¬ten in the 1970s. So why are they almost extinct today? Contract bond losses have been severe in the past several years, sureties reporting losses exceed¬ing 110%. But the same proof is not provided on coal reclamation bonds. A surety bond is generally required when one party has an agreement with another party, and that party wants a guarantee from a third party that a job will be completed according to the terms and conditions of a written contract. In the case of a reclamation bond, the surety company (surety) is the financial party. It extends the credit and a guarantee to the obligee (the State, Commonwealth, or Office of Surface Mining) that the principal (the coal operator/company) will complete the terms and conditions of the contract (the rules and regulations governing mining and reclamation). The Surety Association of America defines a surety bond as an agreement providing for monetary compensation should there be a failure to perform specified acts within a stated period. Webster's Dictionary defines surety in the following ways: "l: the state of being sure; 2a: a pledge or other formal engagement given for the fulfillment of an undertaking and; 3b: one who has become legally liable for the debt, de¬fault, or failure in duty of another." Banks never make accommodation loans. Either the loan is good or no loan is made. Surety companies feel the same way about surety bonds. In fact, the average person does not realize the dangers of becoming surety for another. How does a surety determine if a company is worthy of receiving surety credit? How is a coal account under¬written today for an obligation that may not be released for many years? When a surety company executes a reclama¬tion bond, it financially puts its name behind the coal company and its guaran¬tee that should the coal miner default on the obligation, the surety will fulfill the contract. How is the surety to determine if a coal company may still be in business five, 10, 20, or 40 years from today?

Jan 1, 1989

By J. W. Bawden, J. Nantel

"The mine operator has two prime objectives when he operates a mine: (l) the mine must be safe, and (2) the mine must operate with the lowest possible costs. The operator constantly faces a dilemma; if he is over cautious with regard to safety, his costs may be very high, and if he is over-zealous in trying to reduce costs, the safety of his operation may be jeopardized.Modern bulk mining methods rely heavily on high productivity non-entry stoping techniques (e.g. open stoping, VCR, etc.). Such techniques have the advantage of removing the operator from the active and sometimes dangerous mining face and ofminimizing costly development. On the other hand, this generally results in a certain loss of flexibility in following irregular ore-waste contacts. If stopes are opened too large and/or are inadequately supported, severe dilution with resulting escalating costs usually results. If initial access drift support is inadequate for latter mine induced stresses high rehabilitation costs may also be incurred.Optimization of stope dimensions should logically occur as part of a general mine rock engineering program, within the over-all mine planning context. The same program should help highlight those areas where drift rehabilitation may be a problem.Whenever successful mining is performed, rock engineering is being applied, either by design or by chance. The cost implications of planned practical rock engineering as an integral part of mine planning and design can be very significant to the ultimate mining ""bottom line"". At Noranda Minerals Inc. allowable stope dimensions are derived using a combination of numerical stress analysis and empirical design techniques. This paper discusses the use of the above techniques and their limitations as tools for rock mechanics based stope dimension optimization. The potential cost implications of such design efforts within the general mine planning context are also addressed."

Jan 1, 1989

By Paul C. Miclea, Robert E. Murphy

The behavior of fire and airflows in a confined tunnel differ significantly from more familiar fire situations outside, due to the buoyant effect which tends to create a layer of hot smoke and gases flowing away from the fire near the crown of the tunnel, while air supporting combustion moves toward the fire beneath the smoke layer. A subway emergency ventilation system is designed to force air to flow through the tunnel, shifting the balance of heated air in the direction of the forced flow and avoiding the "back-layering" of hot gases and fumes. This paper presents a computer program, called the "Subway Environment Simulation" (SES), which can be used to predict airflows created by the emergency ventilation system. It utilizes the latest state-of-the-art analytical treatment of fires in enclosed spaces, including observations from mine fires and gas explosions. The program allows designers to reduce construction cost by identifying unnecessary ventilation shafts and by verifying fan capacities. In addition, the program allows the designers and operators to determine safe evacuation routes, in case of a train fire, by predicting the occurrence of back-layering. It can be used to determine when the ventilation system can control the direction of smoke movement to provide a clear and safe path for evacuating people and facilitate fire fighting operations.

Jan 1, 1989

By Thorvald Wetlesen

Computer controlled drilling is now proven technology. It was first introduced by the development of the Furuholmen system for a prototype three boom tunneling jumbo in Norway in 1978. Now, 13 rigs with this concept are in operation in Europe, 3. in mining in England and. 10 in tunneling elsewhere in Europe. The system is also adapted to roadheader guidance. Practical experience has shown that the computer control system makes it possible to drive tunnels with a more accurate contour thus reducing the total amount of rock excavated, and where a full concrete lining is required a reduction in concrete volume is achieved. The total tunneling economy is improved. In the future we expect to see a wider range of instrumentation on jumbos, from the simple direction instruments to computer guidance systems for monitoring only, as well as fully automatic drilling to a programmed drilling pattern. More compact and reliable electronics will be available. Systems with low power consumption will fit easily into flameproof applications. Cabling complexity will be reduced by connection of sensors to serial signal lines.

Jan 1, 1989

By G. Labonte

The behavior of four different redox sensing electrodes (gold spiral, black platinum, chalcopyrite, and galena) during roughing and cleaning flotation is examined and related to the flotation response. Although it is difficult to provide unequivocal interpretations of the different potentials measured, the results indicate that the solution potential (as sensed by the black platinum electrode) is different from that of the pulp potential (gold spiral) and is only weakly related to the flotation response. On the other hand, the potentials exhibited by the gold spiral and the two mineral electrodes are related to the floatation response. The gold and mineral electrodes exhibit different transcient responses during the addition of flotation modifiers (e.g. NaCN, SO2). These responses appear to be related to the reactivity of the minerals and could indicate the conditioning time required to achieve flotation or depression of selected minerals.

Jan 1, 1989

By Andrzej Wala, Tom Altman, Tom Hughes

The University of Kentucky Mine Ventilation Manager (UKMVM) is a system that contains Level Five knowledge bases and comprises an expert mine ventilation management system. The package uses production rule language (PRL) to interpret data monitored from sensors, e.g., for airflow, temperature, and concentration of gases, in an underground mining environment. Activated from the PRL knowledge bases are Pascal subprograms which (1) organize the monitored data to set up emergency consultations, (2) display graphic representations of a mine's ventilation network with the latest sensor readings, (3) provide interactive updating of mine ventilation parameters, e.g., resistance changes, revised flow requirements, and new regulator and fan settings. Also activated from these knowledge bases are programs which (1) monitor airflow, temperature and gas concentrations from a physical mine ventilation model and (2) adjust regulator openings and fan rpm's. Thus, as an expert system the UKMVM not only presents advisory consultations for underground environmental emergencies, but also serves as an interface between the monitoring and responsive control aspects in the continuous maintenance of normal mine ventilation.

Jan 1, 1989

By L. W. Laage

Throughout recorded history, underground fires have plagued mining operations. Compared with other hazardous situations in underground mining, a fire can become a global problem by swiftly spreading deadly carbon monoxide and other products of combustion (POC's) throughout the whole mine, often without warning. Experience has shown that when fires are detected and located in their early stages, they are much easier to control and proper escape routes can be more intelligently selected. Recent advances in sensor and data communication technology have made reliable mine fire .detection system installations possible. Unlike building construction. in a mine, it is impractical to install detectors at every desired location. Abandoned workings and unsafe locations preclude sensor installations from both safety and economic standpoints. The net effect is that some fires are detected and located early while the location of others, even if detected early, remains unknown too long for effective evacuation and fire fighting.

Jan 1, 1989

The application of Kirchoff's laws to two adjoining mine ventilation network meshes containing fans results in the construction of two general quadratic equations. These equations may be solved to give the resultant airflows and hence fan duties within the system for given network parameters and fan characteristics. This technique has a wide application for calculating the duties of fans in various combinations within a mine ventilation system. Recent difficulties in economically maintaining environ- mentally safe conditions in underground working areas distant from main ventilation fans has led to increasing interest in the use of controlled partial recirculation of ventilation. This paper develops a recirculation model which can be solved directly using mathematical techniques obviating the need for iterative techniques such as the Hardy-Cross method. The advantage of a direct mathematical analysis is that mathematical algorithms may be constructed to completely describe the ventilation system under a wide range of operating conditions. This technique is applied to controlled partial recirculation ventilation systems to demonstrate its advantages for mine ventilation planning.

Jan 1, 1989

By G E. Exedaktylos, Y Zhou

The complex and non-linear nature of blast fracturing has restricted common bract design primarily to empirical approaches. The code developed for this investigation simulates the pattern of interacting radial fractures from an array of blastholes, at various burdens and spacings, and in simultaneous and delayed modes. The resultant pattern is analyzed and a fragment adze distribution calculated.

Jan 1, 1989

By Marian Radetzki

The economic developments and industrial behavior patterns that led to a lasting excess capacity in the world non-ferrous metals industries from the aid-1970s are explored. Detailed attention is devoted to analyzing and defining crucial concepts like "capacity", "excess capacity", "capacity maintenance" and "investments". Empirical evidence of capacity utilization and capacity growth in the industries under study is provided. The coincidence of excess capacity and low prices on the one hand, and investments in capacity maintenance and capacity expansion, on the other, is seen as a consequence of substantial declines in the metal industries' investment and production costs during the period studied.

Jan 1, 1989

By A. W. Khair, S. J. Jung

"IntroductionIn a typical incremental loading test, the AE activity increases rapidly in the initial stage of the loading. It is associated with initial closure under compression of favorably oriented cracks already present, together with sliding of crack faces against each other /1/. After the initial stage, crack closure and movement largely cease and the AE activity drops to a barely detectable level /2/. In the final stage of loading test, cracking associated with the onset of inelastic deformation' occurs, and the rate of AE rapidly increases /3/ indicating an increase in the •number of events associated with higher number of microcracks. To understand better primary fragmentation process, Anderson and Ruzzi conducted tests to identify a practical method of monitoring fracture development in rock, as caused by an excavation tool /4/. They proved that a relationship existed between the AE activity, generated during fracturing and the amount of fracture surface area created.A process of fragmentation, demonstrated by conical bits acting orthogonal to the flat surface of block of coal specimen with and without lateral confining pressure is presented here. The monitoring of AE during the fracturing process of rock/coal has been a very useful indirect method in studying fracture mechanism.Specimen PreparationLarge blocks of Waynesburg coal were obtained from a surface mine. These blocks were then out and molded to approximate dimensions of 25.4 x 25.4 x 15.2 'an (10 x 10 x 6 in.). These specimens were instrumented with three strain gages in a 45 degree rosette. One was mounted parallel to the bedding plane direction, another was tinted at an angle of 45 degree from the bedding plane direction and the third was mounted perpendicular to the bedding .plane direction. Each of the three strain gages were set 5.1 an (2 in.) away from the impact point.Typical Test ProcedureIn a typical experiment, the specimen was placed in the confining chamber.Predetermined equivalent in-situ stresses were applied to the specimen by using two sets of hydraulic cylinders. Two 1 in. thick steel plates ware positioned between the sample and the hydraulic cylinders in order to distribute the pressure uniformly over the whole surface of the specimen. The LVDT null position was adjusted with respect to the coal face. After setting the LVDT, the bit and associated weight was lifted to a predetermined height (equivalent to a predetermined kinetic energy) by a win. The three strain gages were balanced using the signal conditioner and the output was recorded by a 6 channel strip chart recorder. The experimental set-up is shown in Figure 1."

Jan 1, 1989

By David K. Crapps

The drilled shaft load tests at Port Orange were part of a demonstration project sponsored by the Federal Highway Administration (FHWA) and the Florida Department of Transportation (FDOT). Three load tests were conducted. Test 1 was a conventional test with the test shaft loaded from the top. Test 2 included an Osterberg load cell at the tip and a conventional load test from the top. Test 3 used an Osterberg load cell at the tip of a production drilled shaft. All three test shafts were socketed into limerock and were carried to failure. This paper describes the test program and presents a summary of the test results. Figure 1 presents some photographs of the load test setups and Figure 2 shows the location of the drilled shaft load tests. SITE CONDITIONS The Port Orange Bridge is located on US A1A over the Intercoastal Waterway in Port Orange, Florida (south of Daytona Beach). The new bridge will provide four lanes of traffic with a 65 foot vertical clearance for Intercoastal Waterway traffic. The channel and flanking piers will be supported by 54" drilled shafts socketed into the rock. The bridge is being constructed in two phases. The southern half will be completed first, the old bridge removed and then the northern half will be constructed. The first phase is scheduled to be opened to traffic in October 1989. Each of the four piers near the channel will be supported by 12 drilled shafts with 6 shafts per pier being constructed in each phase.

Jan 1, 1989

By Claus Becker

Waterbearing, cohesive or non-cohesive grounds with glacial stone deposits are found very often in Europe. The problem consists of destroying the boulders and supporting the face simultaneously. At the example Grauholztunnel Bern ( outer diameter 11,60 m ) the theoretical attempt of solutions for the big machines is described: destroying of the boulders with roller discs, hydraulical support of the front. The problem of coming out of stones of a certain size from the surrounding matrix will be discussed. Further diminishing to the size that can be handled by pumps is executed by a crusher, situated in the center of the machine. At the same example the theoretical attempt for headings in cohesive soil with stone deposits are shown. Surface structure of the cutting wheel and working chamber as well as controllable current movements are the solution here. The danger of clogging discs and stone crusher has to be encountered by right positioning of the tools and jetting nozzles. At the example Sewer MoosstraBe Salzburg the same problems are discussed for the Mikro-Tunnels. The pipe-jacked sewer lines have outer diameters from 485 and 805 mm. With this method, the stones have to be holed through. The wear of the cutting tools determines the [ ]

Jan 1, 1989

By C. W. Schultz

The Mineral Resources Institute at The University of Alabama is engaged in a program whose objective is to develop a beneficiation system for Eastern oil shales. Prior experience (1,2) at The University had shown that the grind required for liberation of the oil rich kerogen was substantially below 20~m. Based on this fact and the rapidly emerging consensus that column flotation is the preferred method for ultrafine particle separation, efforts were focused on the column flotation of oil shale. This paper, which must be regarded as a progress report on a continuing MRI project, describes the observations made and the results achieved to date. The investigation is being conducted in two phases. The first phase has been completed and consisted of a factorially designed experiment conducted for the purpose of screening a set of primary flotation variables. The second phase, which is still in progress, is focused on optimization of the operating conditions and development of a flowsheet for specific shales.

Jan 1, 1989