Search Documents

By I. G. Townsend, S. A. Buckley, C. I. House

"SummaryBritish Petroleum plc is developing a new gold recovery process known as coal gold agglomeration (CGA) for the recovery of gold from its ores. Liberated gold grains are recovered with high efficiency by adhering to agglomerates of coal and oil. The process is simple, can recover gold grains down to very fine sizes, avoids the large scale use of cyanide and provides the industry with an important new process option.A technical appraisal of the process has been performed on an extensive range of gold bearing materials. Ore types have been identified from which high gold recoveries can be achieved. A spreadsheet based computer program has been used to estimate the preliminary capital and operating costs of the process. Comparison with established gold production costs shows that the process costs of CGA, on the appropriate ore types, are potentially very attractive, which will enable economic treatment of lower grade ores than is currently possible using conventional cyanidation. Treatment of known placer deposits or gravity concentration plant tailings may be the most rapid means of demonstrating the process at a commercial scale prior to more widespread applications.1. INTRODUCTIONWestern world gold production for the 1980s has shown rapid growth sustained by a demand for gold at a favourable price (Fig. 1). Heap leaching and CIP/CIL operations have been responsible for the major part of new production during the 1970s and 1980s with present overall production costs averaging US$200/oz in Canada, USA and Australia and US$265/oz in South Africa [l]. A great deal of research and process development effort in the 1980s has been towards the treatment of refractory ores. Operating costs for the economic processing of these ore types by currently available routes are around US$300/oz [2]."

Jan 1, 1989

By Richard R. Klimpel

INTRODUCTION The purpose of this paper is to summarize the current status of reagents used in the mineral industry plus present some current challenges and possible new technologies of the future. Table 1 lists the important families of reagents which, when taken together, constitute at least 95% of the current commercial reagent market. A very approximate estimate of the free world reagent market size in mineral applications is about 1.5 to 2.0 billion dollars (U.S.) using 1985 data. Obviously, to serve such a large market requires the effort of many different types of commercial supply sources. It is estimated that there are over 300 industrial firms in the free world that have a dedicated business/technical structure for supplying reagents related to the mining industry. There are a number of characteristics which are associated with the product families listed in Table 1. Understanding these characteristics helps to provide a realistic economic/technical basis for outlining future challenges in mining chemicals. 1.Essentially all of the products listed are old chemistry in the sense that the molecules have been known and manufactured for at least 25 years. This has not been a highly dynamic field of endeavor from the viewpoint of new product introduction. 2. The greater majority of the products listed can be viewed in commercial terms as "commodity" chemicals, that is, they are available from many sources and the pricing of a some- what generic product generally dominates differences in product quality or uniqueness. With commodity pricing, reagent suppliers significantly reduce research expenditures, loosen product quality somewhat if the applications of the reagents allow, etc. in order to be cost competitive.

Jan 1, 1989

By Gary L. Self, Ronnie Daniel

With the advent of large scale blasts utilizing overburden casting techniques, it was imperative that an ultra reliable surface delay system be developed. Shock tube and detonating cord surface delay systems have been hampered by the lack of a reliable easy-touse method of incorporating multiple paths of initiation to each hole. Two new redundant nonelectric delay systems have been developed utilizing multiple signal paths to allow a higher degree of safety and reliability. The first system designed uses a combination of detonating cord and nonelectric shock tube delays to allow multiple delay paths to each hole. The second system incorporates a new all shock tube delay system which allows multiple delay paths while minimizing over-pressure by eliminating detonating cord trunk lines. These two redundant systems have been used in over 500 production blasts without any misfires due to surface cut-offs or detonator malfunctions.

Jan 1, 1989

By R. C. Klimpel

Size reduction of material in aqueous pulps by the use of tumbling media overflow discharge mills is an important and common unit operation in industry. There also has been extensive attention given in recent decades on developing a more fundamental understanding of the breakage processes involved, especially in ball mills. These studies have mostly emphasized the use of size-mass balance or population balance approaches for quantifying the analysis and design of size reduction circuits, ego Austin, et al (1984).

Jan 1, 1989

By Moinpour M

The kinetics of reduction of copper (cuprous) sulphide with CO-CO2-He gas mixtures, using an excess of CaO(s) as a sulphur-scavenging substance were investigated in the temperature range 855° - 950°C by a thermogravimetric method. Several gas compositions were employed at each temperature. Potential carbon deposition was overcome by preheating the reducing gas mixture. The phase-composition and the morphology of partially reactedsamples were analysed by a SEMlEDAX unit. The reduction rates showed strong dependence on the bulk gas compositions (CO, CO2) and, in most cases, the rate declined with rising temperature. The rate-controlling step appears to be the diffusion of CO2 gaseous species through the micropores of the CaS(s) - product layer which builds up around the CaOcore.

Jan 1, 1989

By Dimitri Frantzos, Stewart Thompson, Ed Skiba, Hans Tammemagi

On behalf of Acres International we would like to thank Frank Chiappetta of Blasting Analysis International for inviting our organization to participate in this state-of-the-art course on blasting analysis techniques.

Jan 1, 1989

By S. N. Mukherjee

Maintenance of equipment in Longwall faces plays a vital role in face performance. This is more prominent when shortage of spare parts and trained personnel occurs. A study was made in an operating Indian Longwall face for identifying the types and meantime between failures. Though the duration was not enough and study was not very elaborate, it revealed certain interesting facts. The machine availability was found to be poor, though a maintenance schedule was followed. Failure of simple parts like AFC chain connectors even resulted in loss of production of 10 times the complete chain cost. This pinpoints that a proper maintenance schedule is to be developed considering the human factors and local conditions existing in the particular country. Operations research techniques could be used in the process.

Jan 1, 1989

By T. V. Swaminathan

Monazite sand is normally processed by, the caustic soda route to produce mixed rare earths chloride, thorium hydroxide and trisodium phosphate. Bulk of the mixed rare earths chloride is used for the preparation of FC catalysts. Recently some of the catalyst producers have shown preference to cerium depleted (lanthanum enriched) rare earths chloride rather than the natural rare earths chloride obtained from monazite. Therefore, a process for producing cerium depleted rare earths chloride, cerium p thorium and uranium from Rare earths + thorium hydroxide obtained by treating monazite based on stepwise hydrochloric acid extraction, was developed in our laboratory. The process involves drying of the mixed rare earths-thorium hydroxide cake obtained by monazite-caustic soda process followed by stepwise extraction of the dried cake with hydrochloric acid under specified conditions.

Jan 1, 1989

By Thomas D. Kaufmann, Robert C. Drury

Few factors are as important as fluctuations in aggregate economic activity and exchange rates in determining the profitability of mineral investments. Macroeconamic theory explains how the two factors are interconnected in today's world and in tomorrow's. We can use macro¬economic theory to lessen some of the risks in mineral investments. And in the current state of the world the risks are high. The above paragraph summarizes our argument. Our goal in this paper is to examine the nature of contemporary business cycles so as to explain their implications for the metal industries, particularly the implications for capacity. Thus, our first section examines the workings, causes, and history of the recent economic fluc¬tuations. In doing so we must understand how current world economy is interconnected, that is, how economic events in one country are trans¬mitted to the rest of the world. Our view is that governments and central banks are key actors in the creating of economic fluctuations. Then, in section two, we work out the implications of section one for the metal industries focussing on comparative advantage, trade, and capacity decisions. Over the last fifteen years the world economic system has had slow overall economic growth and has had strangely unpleasant recessions. While future business cycle will not repeat the de¬tailed pattern we have seen, there will be similarities. The similarities need to be under¬stood before investment occurs. The slow growth in the world economy since the early 1970s has aggravated the problems from business cycles, created its own problems, and has partially hidden the effects of other events. Major realignments of currencies are likely to take place over a business cycle. The nature of the causes of the cycle will determine the direc¬tion of change in the exchange rates. For example, whether a USA recession will be accompanied by a weaker or a stronger dollar will be determined by the cause of the recession. The realignment of currencies over a business cycle leads to a realignment of comparative advantage in the metal industries. Thus, not only will world metal consumption vary over the business cycle but the impact on various countries' metals industries will differ consi¬derably. Competitiveness often depends more on the value of the dollar than it does on inherent efficiency and wage rates. Capacity decisions are inherently riskier due to the country specific nature of exchange rate risk. A realignment of currencies changes the pattern of trade if and only if the country with the cheaper currency also has idle capacity. The importance of our topic is indicated by Table 1 which shows the impact of cyclical and exchange rate shocks on the USA metal industry. In the cyclical downturn, from the peak of 1979 to the trough of 1982, consumption dropped by a fifth to a third. Metal price moved in the same

Jan 1, 1989

By Boshou Bian

Air quantity is the primary parameter governing the working condition of a mine fan. In order to improve the fan performance and efficiency, reduce its energy consumption, and guarantee mine safety, it is very important to obtain an accurate value. However, generally speaking, the fan ducting or drift on surface is very short in distance and contains sharp bends. The air quantity of the mine is so concentrated in this way that the air velocity becomes very high, and the airflow, either in the fan drift before the fan impeller or at the downstream diffuser, is very turbulent. Therefore, no anemometer is satisfactory because there is too much difference between the measured value and the actual value of air quantity at the mine fan.

Jan 1, 1989

By Yingxin Zhou

Virtually every coal seam in Appalachia will at some time be subject to multi-seam interaction (Wu et al, 1987). Many such problems result from seams which lie in close proximity or have split and lie within thirty feet vertically of one another. Existing techniques for multi- seam design have concentrated on conditions where the entire inner burden is not the failing member and are unsuitable for ultra-close multi-seam design. Structural integrity of the inner burden must be maintained if two superimposed seams are to be mined separately and under- standing possible failure mechanisms of the inner burden is an essential first step in the design process.

Jan 1, 1989

By M. J. Preim

Two case histories are presented on the evaluation of static bearing capacity of piles driven in soils that exhibit time dependent strength changes. Under consideration are a steel and a concrete pile driven into soils generally consisting of silty and clayey fine sand. Pile dynamic measurements and analyses were performed on both piles during initial installation, and also during restrike one week later. This information was used to predict each pile's long term capacity (defined as 14 days after initial drive), which was then compared to that measured with a static load test. Agreement between predicted and measured capacities were remarkably good, with an average error of only 4.5 percent. Two weeks after driving, total pile capacities were three times those at the end of drive. If only the skin friction was considered, however, it increased by an average factor of 16. The increase in pile capacity was determined to be linear over the time period considered.

Jan 1, 1989

By R. Allan Wallis

In the past mining engineers have tended to rely heavily on the advice of fan manufacturers in relation to fan equipment issues. A more adequate approach was advocated in a paper [ Wallis, 1965 ] submitted to the Eighth Commonwealth Mining and Metallurgical Congress held at Surfers Paradise, Australia during 1965. At that time Mount Isa Mine were in the process of installing 3 large 6096mm (20ft) diameter vertical axial flow surface fans of an advanced type [ Mathews et al, 1967 ]. The preliminary feasibility studies prior to preparing the detailed job specification for this project were extremely thorough with the result that it was possible to include detailed information and instructions in the document, ensuring the procurement of equipment that was satisfactory in all respects. Full advantage was taken of expert services provided by external organizations during the large coordinated multi-disciplinary exercise. My continuing activity and development in relation to the technology of axial flow fans is now at a stage where all known design and performance data are accessible through CAD programs [ Wallis and Kipp, 1987 ]. The extensive calculations that were necessary in 1983 can now be carried out in a mere fraction of the time, and with complete confidence. Model testing in order to validate the fan and duct design proposals is, in my view, no longer essential. The first of the computer programs enables a mine ventilation engineer to study a large number of alternative axial fan arrangements for comparison with the centrifugal alternative. By entering the volume flow rate, fan pressure and air density, he can then with ease, and rapidly, investigate the effect of various blading arrangements, downstream evasee area ratios, and hub ratios, on fan diameter and speed, with their related attainable fan efficiencies. This procedure had its origin back in the 60s when I was advising mining companies on new fan equipment. At that time such an investigation was quite lengthy and lacked the precision and completeness that is now available within the present programs. To obtain the major benefit from these outputs, it is most important not to be disconcerted by the three very important nondimensional parameters, namely, the tip flow coefficient (LAMt), the fan pressure coefficient (Kt or Kit), and the swirl coefficient (Es and/or Ep) as these are important when assessing the various design proposals. When seeking an understanding of the role and importance of each of these variables, ample help is provided in the user manual; the design recommendations are summarized in the help screens which are readily accessible within the design programs.

Jan 1, 1989

By S. C. Dhara

The recovery of Platinum Group Elements from various industrial scraps and spent materials in the form of high and low grade, such as, impure metals, matte, catalysts and other ceramic substrates, etc., has .been described by using high pressure reaction method. Nickel, Stainless Steel, Titanium and glass lined reaction vessels? are used in the reaction process. Primarily, the method involves either direct leaching of the substrates from the metal value or dissolving the precious metal from the substrate. Both acids and alkalies are used along with other reagents in the reaction process. The temperature and pressure of the leaching process are the main criteria for the reaction kinetics.

Jan 1, 1989

By M. Kaya, A. R. Laplante

"Since the beginning of eighties the use of flotation columns has surged in Canada and abroad; the metallurgical superiority of columns over mechanical cells is in great part due to froth washing, which ensures higher gangue rejection and selectivity. Can wash water, which has proven so beneficial, be used in mechanical cells? Although froth washing technology was widely implemented in Soviet plants for bi tuminuous coal, and alusite, powellite, scheelite, molybdenite, etc. more than 25 years, it has been neglected in the western world. Published data suggest 10 to 15~ increases in grade and/or recovery with wash water in mechanical cells (Klassen and Mokrousov, 1963). There are at least three wash water plant applications in Zaire, Chile, and Canada, but little, if any, published information is available. This research work, which is the first extensive fundamental study related to froth washing in mechanical cells, attempts to answer the questions of how, how much, and where should wash water be added.This project was undertaken in three stages:1. Bench-scale laboratory tests with a 6.5 L Denver cell at McGill using a silica flour and a slime reject from Niobec (St.Honor6).2. Pilot-plant scale tests with a 65 L Denver cell at McGill using the silica flour and a complex Cu-Ni sulphide ore from the Strathcona mill of Falconbridge.3. Plant-scale tests with a bank of 2800 L Denver cells at Falconbridge Ltd. for complex Cu-Ni sulphide ore and Eastmaque Gold Mines Ltd. for Au tailing reclaimation."

Jan 1, 1989

By R. L. Beatty

Bond International Gold's Colosseum gold mine was discovered in 1865. No recorded production occurred, however, until the 1930s, with production of about 19 kg (615 oz) of gold. The mine was closed in 1942 as a nonessential industry during World War II. The property was acquired by Dallhold Resources in mid-1986. Construction of a 1.1-million Mt (1.2-million st), carbon-in-pulp (CIP), cyanide mill began in November 1986 and was completed in September 1987. Minable reserves are estimated to be 9.5 Mt (10.5 million st), with an average grade of 2.1 g/t (0.061 oz per st). This article describes the general process flow and plant equipment. And it looks at the maintenance and operational problems encountered in the first six months of operation. Process description Ore is direct hauled from the open-pit mine 1.5 km (1 mile) to the crushing facility. There it is crushed to -152 mm (-6 in.) with a single- stage, 1.5-m x 1.2-m (60-in. x 48-in.), 186.5-kW (250-hp), Fuller-Traylor jaw crusher. The ore is then stockpiled in a 31.7-kt (35,000-st) reclaim ore pile. Lime is added to the crushed product as it is conveyed to a single 6.4-m x 4-m (21-ft x 13-ft), Hardinge semiautogenous grinding (SAG) mill, followed by a single 4.3-m x 7.3-m (14-ft x 24-ft) Hardinge overflow ball mill. After grinding, the slurry is thickened and then preaereated for three hours. Following preaereation, the pulp is leached with NaCN at a pH of 11, also for three hours. The slurry then goes through a seven-stage CIP circuit for 21 hours. Then the tailings slurry is preaereated for three hours before cyanide destruction using the Inco process. Loaded carbon is eluted using an Anglo American strip, followed by electrowinning on stainless steel wire. The stainless steel wire is transferred to refinery cells where the gold and silver is plated on stainless steel plates. Following electrore-fining, the gold-silver foil is removed, melted, and poured into dore bars for shipment. The crushing, milling, refining, and maintenance processes require 37 people. Crushing The crushing area required changes and modifications following start-up. Several areas are of specific note. Structural failures Rubber support cushion blocks located under the coarse ore bin failed. These were replaced with heavier, more durable blocks and have since appeared to be satisfactory. A severe structural vibration was encountered in the entire crushing facility. A mechanical engineer, brought in by the contractor, determined the structure needed more support and cross-bracing.

Jan 1, 1989

By J. Launay

In order to control and dispatch the sewage water coming from 3 tunnels toward 2 downstream sewage tunnels, a large cavern has been excavated in a suburb of PARIS. Located at a depth of 47,00 m, it has been excavated using the NATM procedure through swelling clay, weathered sandstone, and marl and chalk. It is 16,50 m high, 12,40 m wide and 60, 00 m long, with an elliptical cross-section and its two ends are egg-shapped. The final lining of the cavern is composed of 30 to 40 cm of shotcrete, steel ribs and passive anchor bars. The excavation stages and related movements were surveyed by extensometers, pressure cells and convergence devices. The design, method of construction of the cavern and the results of the measurements made are commented.

Jan 1, 1989

By Chao-jiong Hou

The necessity of using tensible rockbolt in the roadway with soft rock, high in-situ stresses, mining influence and other complex conditions was discussed, the structures of three kinds of tonsibte rockbolt and design principle were introduced in this paper. The tests of analogue material simulation under plane strain condition and underground industrial tests indicated that the effect of controlling deformation surrounding roadway by use of tensible rockbolt was good.

Jan 1, 1989

The formation of tension cracks in slopes is well known. Analytical studies require the determination of a critical slip surface for any slope and, in doing so, it is necessary to consider an appropriate tension crack. A general yet simple approach is proposed for identifying the critical slope failure surfaces associated with critical tension cracks. The minimum factor of safety consequently reflects both safety against shear sliding and tensile failure. In general, the critical slope failure surface for a slope determined in this way differs from that which is obtained without optimizing the position and depth of the tension crack. In particular situations, the difference is significant.

Jan 1, 1989

By Jorge Martinez

The Muck Valley Hydroelectric Project in Northeastern California required construction of a 3.65 meter tunnel through 6,623 meters of mixed volcanic flow deposits within a critical time frame. As Engineer and Construction Manager for the Project, Morrison-Knudsen Engineers invited bids for both Drill and Blast as well as Tunnel Boring Machine methods, selecting a contractor proposing a TBM designed and built specifically for this project which could excavate a wide variety of materials and maintain acceptable progress rates to complete the work within schedule. Tunnel lining as required included shotcrete with metal fibers and full circle concrete.

Jan 1, 1989