Search Documents

By William M. Schafer

Forage plots were established on agricultural lands contaminated by acid mining waste. The acid produced through oxidation of pyrite and other sulfides caused elevated solubility and plant availability of copper, zinc, and arsenic which killed vegetation and polluted surface and groundwater. Soil amendments including agricultural lime (CaCO3), hydrated lime (Ca(OH)2), phosphorus, and organic matter were used to reduce the toxicity of metals. Several acid-tolerant grasses were used to vegetate the amended soils. Various soil extraction techniques were used to see which best correlated with vegetation performance. The extractions corresponded to three "forms" of metals in soil including soluble (water-saturation extract); plant-available/weakly adsorbed (DTPA extract); and total (HNO3/H202 extract). Of the extractants tested the DTPA levels appeared to correlate best with metal levels in plant tissue. The DTPA soil extractant serves as a useful tool in predicting potential phytotoxicity of mine waste materials.

Jan 1, 1989

Jan 1, 1989

By Joan Weinberg

Real gross national produce (GNP) grew at a seasonally adjusted annual rate of 2.0% in the fourth quarter (table 1). The restrained quarterly growth rate was the slowest in 2 years, and was substantially slower than the 2.5 % rate of the previous quarter. According to the U.S. Department of Commerce, the summer drought reduced the fourth-quarter growth rate by 1.1 percentage points. A growing trade deficit and a reduction in business investment were the key economic factors curtailing growth. The trade deficit widened by $6.8 billion, reflecting both a surge of imports and a slowing of exports. Business investment declined 3.7%, mainly as a result of a slowdown in computer sales. On a year-to-year basis, the economy grew at an inflation-adjusted rate of 3.8% for 1988, the fastest in 4 years, despite the drought. However, on a fourth-quarter-to-fourth-quarter basis, real growth measured 2.7%. Increased exports and business spending for plant and equipment accounted for much of the 1988 GNP growth. Employment continued to grow as the manufacturing sector added 414,000 new workers (table 2). Of these, the primary metals industry added 26,000 workers, and the clay, glass, and stone industry added 10,000. The civilian unemployment rate remained low throughout 1988, fluctuating between 5.3% and 5.4% during the last quarter.

Jan 1, 1989

By Terry J. Close

Between 1986 and 1989, at the request of the U. S. Bureau of Land Management, personnel from the U. S. Bureau of Mines Western Field Operations Center studied the highly-mineralized, 25,335-acre, Crack Canyon Wilderness Study Area (UT-060-028A), to evaluate its identified mineral resources. The 16-mi-long, 2-mi to 4-mi-wide stud/ area is on the southeast side of the San Rafael Swell, about 40 mi southwest of Green River, Emery County, southeast-central Utah. The study area is underlain by Mesozoic sedimentary beds. Uranium, the principle mineral resource, occurs in two formations. The principle uranium deposits are in mudstone, sandstone, and conglomerate lenses in the 22-mi-long outcrop of the Triassic Chinle Formation which parallels and straddles the northwest boundary of the study area, Some small low-grade uranium occurrences and an extensive gypsum deposit are hosted by the Jurassic-age rocks that underlie the southeast part of the study area.

Jan 1, 1989

This is the initial issue of STATE MINERAL SUMMARIES. This publication provides estimated data and summaries of mineral activities at the State level for 1988. Most of the estimates are based on nine months data. These summaries have been prepared in cooperation with State geological surveys or related agencies. Individual State summaries are published separately as State Mineral Industry Surveys and copies can be obtained from the appropriate State Activities field office.

Jan 1, 1989

By August J. Kwitowski

This report presents the results of a joint Bureau of Mines-U.S. Department of Energy project that evaluated a newly developed low-coal mining system: the 4M miniminer system. The evaluation took place from April through October 1981 and determined potential health, safety, and productivity factors for the mining system using the surface test facilities at Bruceton, PA. The planning, testing, results of testing, and a summary evaluation of the 4M miniminer system are included in the report. The miniminer system was found to be a very good concept with future potential for safe, healthful, and economic production in thin-seam mining. The mining system was also judged to have considerable potential for use in some coal seams that are presently considered unminable by other existing mining equipment. The preproduction, prototype version of the miniminer system that was tested suffered from several safety and production problems. These problems are also described, along with suggested remedies.

Jan 1, 1989

By S. B. Patton

A comprehensive approach to the development and organization of an expert system that is designed to assist electricians in diagnosing electrical faults m mining machinery is discussed. The system includes diagnostic, reference, and tutorial programs. The diagnostic portion of the system is based on a causal-reasoning approach which is used to establish a hierarchy of symptoms and the subsequent production rules for identifying component-level failures m the motor-control circuit of a shuttle car. With this approach, conclusions are developed directly from knowledge of the circuit and its behavior (in both working and failure modes) based on first principles, rather than the heuristics of a domain expert. The symptoms and their hierarchical structure an: formulated by creating "what-if" scenarios and performing a qualitative circuit analysis for each fault Techniques for incorporating interactive graphical displays of the circuit schematic into the diagnostic portion of the system are also presented. Supportive computer programs that provide' reference material and tutorials on the circuit are also described.

Jan 1, 1989

By K. E. Hjelmstad

Solution mining operations often encounter difficulty maintaining adequate leach solution flow into the ore formation because of loss of formation permeability near the injection well. Permeability loss caused by swelling and breakup of clays and fine particle migration can often be the cause of the problem.

Jan 1, 1989

By Swayn G. P, Floyd J. M

BHAS, together with the G.K. Williams Laboratory, and Ausmelt Pty. Ltd., has examined a number of possible alternatives to conventional silver cupellation in gas fired reverberatory furnaces. Of these alternatives, a Sirosmelt furnace was preferred for both technical and economic reasons. Small scale work on Sirosmelt processes was carried out at the G.K. Williams Laboratory at Melbourne University in 1985/86. Pilot scale work was carried out at the Ausmelt plant in Melbourne in July 1987. Board approval for construction of a full size plant was received in October, 1988, and construction of the plant is currently underway. The plant is expected to provide significant savings in operating costs and silver inventory. Hygiene around the furnace should also be greatly improved. An increase in cupellation rate of at least ten times is expected, compared with the conventional reverberatory furnace.

Jan 1, 1989

By R. W. Lai

Cyclic voltammetry (CV), flotation response, evolved-gas analysis (EGA), and X-ray photoelectron spectroscopy (XPS) were employed to evaluate the major differences in the surface property and surface reactivity of coal pyrite and mineral pyrite.

Jan 1, 1989

1. New books from The Institute of Metals Physical and elastic characterisation, edited by M. McLean. 1989. 228 pp. £25.00.High nitrogen steels, edited by J. Foct and A. Hendry. 1989. 461 pp. £49.50. Proceedings of the First International Calcium Treatment Symposium. 1988. 116 pp. £15.Design for recyc/ability, by Michael E. Henstock. 1988. 150 pp. £15. Solidification processing. 1988. 549 pp. £45.Proceedings of the First International Calcium Treatment Symposium. 1988. 116 pp. £15.Marine engineering with copper-nickel. 1988. 103 pp. £18.Sir Henry Bessemer: An autobiography. 1989.380 pp. £16.95. 2. Other publishers Occupational safety and accident prevention. Behavioural strategies and methods, by C.G. Hoyos and B.M. Zimolong. Amsterdam, Elsevier, 1988. 218 pp. Dfl. 180.00. Algorithms in real algebraic geometry, edited by Denis S. Arnon and Bruno Buchberger. London, Academic Press, 1988. 274 pp. £15.95.

Jan 1, 1989

By Jr. Mason

Eminent Domain is the power of the government or municipality to take property for public use without the consent or acceptance of the owner. Typically the agency taking the property will make an offer on the property, hoping that the owner will immediately accept and allow work to begin. If a mutual resolution regarding the property value cannot be reached, however, the municipality will condemn the premises and institute a condemnation action in a court of law, which is when the problems begin. The power of the government to take the subject property is limited by the Federal and State constitutional duty to pay "just compensation" for the property.

Jan 1, 1989

By R. Lanthier, A. Broussaud, J. C. Guillaneau, D. Hodouin

This study presents a method for upgrading the information extracted from the measurements given by the sensors of a pilot grinding circuit. For that purpose raw signals are combined to process models for extracting, through filters, the best information on the process state. Two different filters are used; one is based on steady-state mass balance constraints and the other one uses dynamic mass balance equations allowing for material accumulation in the equipment. The filters are designed and tuned with the help of a grinding circuit dynamic simulator and are then implemented in the pilot plant. Their performances and usefulness are discussed.

Jan 1, 1989

By L. Cheng, M. S. Seehra, P. S. Raghoottama

The four major IR bands of a-quartz at 1080, 797, 693 and 488 cm-1 are studied at room temperature by FTIR-Photoacoustic Spectroscopy. Using Rosencwaig-Gersho theory, equations for the PAS signal q for the thermally thin and thermally thick cases are derived and it is shown how thin to thick transition occurs and leads to saturation as the sample mass is increased. For sample mass < 2 mg, q is proportional to sample mass thus defining the region for quantitative analysis. The dependence of q on the chopping frequency f is found to vary as q f-n with n ? 0.9 for quartz, in good agreement with the RG theory.

Jan 1, 1989

By B. J. Arnold

Over 600 million tons of coal are handled annually for use by the country&apos;s coal-fired power plants. Coal is transported in various ways. overland conveyors. Railcars, trucks, and barges. It can travel short distances or thousands of miles, picking up moisture, freezing, or drying. When the coal is received at the power plant, environmental problems with fugitive dust and further handling problems can arise.

Jan 1, 1989

By R. H. Sailors

During the last 15 years, the North American Mining Industry has experienced increasing usage of cast high chromium white iron grinding media in wet grinding applications. First introduced into the cement industry (klinker grinding) where wear rate reductions of four or five times have been realized compared to steel balls, this same grinding media serve the iron, copper, and phosphate markets by resisting not only impacts and abrasion, but also corrosion which occurs in wet grinding. In these markets, single mills containing 250,000 kg of grinding balls are not un-common and hence the economic potential with respect to lower wear rates can be significant. Add to reduced wear rate the increased production efficiency that is possible and it is readily understood why much of the mining industry uses cast high chromium grinding media. Metallurgically, the alloys used consist of a martensitic matrix containing hard M7C3 eutectic carbides. Carbon (2.0 to 3.5%) and chromium (12 to 277.) are characteristically used to arrive at the desired properties.

Jan 1, 1989

1. Mintek reports The folowing reports are available from Mintek, Private Bag X3015, Randburg, 2125 South Africa. They are available at R25 (plus R3,25 GST) per copy to South African addressees, and US$25 per copy (including airmail postage) to addressees elsewhere. Report M91D A mineralogical investigation of samples from the Renosterkop tin prospect near Upington, by M.J. Southwood. First issued Jul. 1983, reissued May 1989. 16 pp. Report M256D The upgrading of Mamatwan manganese ores heavy-medium separation, by P. W. Overbeek. First issued Apr. 1986, reissued May 1989. Report M299D A mineralogical investigation of samples from the Eenzaamheid cobalt-molybdenum deposit, by C.D. de Nooy. First issued Jan. 1987; reissued May 1989. Report M301D The evaluation of manganese metal powder by automatic image analysis, by E.J. Oosthuyzen. First issued Feb. 1987, reissued May 1989. 13 pp. Report M311D Mineralogical and beneficiation studies of ore from Lutzputz, by R.N. Guest and C.T. Logan. First issued Mar. 1987, reissued May 1989. 13 pp. Report M314D The beneficiation of a sample of magnesium ca/crete, by L. Jonker. First issued Apr. 1987, reissued May 1989. 13pp. Report M369 The determination, by flow-injection analysis, of thiocyanate, by E.A. Jones and M-J. Hennings. Jun. 1989. 7pp. Report M389 A spectrophotometric method for the determination of zinc by flow-injection analysis, by D.E. Barnes and RA. Jones. Jul. 1989. 15 pp.2. Recent publications Pumps-principles and practice. Available from K. Myles & Associates CC, P .0. Box 2212, Northclif 2115. :200pp. R99 including GST. Standard handbook of hazardous waste treatment and disposal, edited by H.M. Freeman. Bergano Book Co., P .0. Box 190, Fairfield, CT 06430, USA. 1120 pp. US$130.Quality control handbook, by J. Juran and F. Gryna Jr. Bergano Book Co. (address as above). 4th 00. 1536pp. US$125.Refractories in the manufacture and transport of pig iron. Verlag Schmid GMBH, P.O. Box 6609, 7800 Freiburg, West Germany. DM 100. The user-computer interface in process control, byW.E. Gilmore, D.I. Gertman, and H.S. Blackman. London, Harcourt Brace Jovanovich Ltd, 1989. " 312pp. $29.Aluminum alloys-contemporary research and applications, edited by A.K. Vasudevan and R.D. Doherty. London, Harcourt Brace Jovanovich Ltd, 1989. " 676 pp. " £90.3. TMS publications issued recently The folowing publications are available from The Minerals, Metals & Materials Society, 420 Commonwealth Drive, Warendale, PA 15086, USA (Telephone: (412) 776-9000, Telex: 9103809397, Fax: 4127763770). Advances in magnesium alloys and composites, by H. Paris and W.H. Hunt (eds.). 145 pp. $65. Arsenic metallurgy-fundamentals and applications, by R. Reddy (ed.). 515 pp. $104. Casting of near net shape products, by Y. Sahai (ed.). 7oopp. $155.Continuous casting of non-ferous metals and alloys, by H.D. Merchant, D.E. Tyler, and E.H. Chia (eds.). 360 pp. $90.Dislocations and interfaces in semiconductors, by K. Rajan, D. Ast, and J. Narayan (eds.). 210pp. $75.

Jan 1, 1989

By Sriram Padmanabhan, Jan M. Mutmansky

The subject of quartz occurrences in respirable coal mine dusts has been of increasing concern in recent years. The primary impetus for this concern has been provided by better measurement technology that has detected an increased number of mines with high quartz content in their respirable dusts. This paper presents the results of statistical analyses of quartz levels in multi-stage impactor samples from eighteen different coal mining sections located in Pennsylvania, West Virginia, Ohio, Illinois, Kentucky, Colorado and Utah. The quartz and kaolinite determinations were then determined by combining impactor stage loadings to provide larger dust masses and applying the infrared spectrometry procedure outlined in Bureau of Mines/MSHA Method P7. The results will be presented using two categories of data collected during two separate phases of the research: (1) quartz concentration data from mines where quartz was known to be present in relatively high concentrations, and (2) quartz concentration data from mines chosen at random. The aspects of the occurrence of quartz in coal mine airborne dusts that will be reported include the size dependence of the quartz content, quartz variations with location in the mining section, and variations due to mining region. The results of the study show a strong pattern of size dependence of the quartz content in mines for which high quartz concentrations exist. A similar, though less pronounced, pattern exists in mines chosen at random. Quartz levels appear to have a varying relationship to section location and strong geographical patterns do not appear to exist in the data collected. Kaolinite content was found to be similar to that of quartz with patterns that are somewhat more consistent.

Jan 1, 1989

By R. V. Ramani

In a 1985 seminar, we were told that overoptimism abounds in Artificial Intelligence (AI), that A1 is neither a science nor a technology yet, and that we will be both exhilarated and disappointed with AI. In fact, even today, there is no single accepted definition of AI; however, certain features have been identified by AI researchers as essential to consider an entity.(e.g: machine or program) to be intelligent. According to Shank (1987), these features include communication (to be able to communicate with), internal knowledge (knowledge about itself), world knowledge (awareness and knowledge about the world outside), intentionality (knowing what one wants and a plan to seek it, ie. goal seeking behavior), and creativity (being adaptable to changing conditions). None of these figures would individually define intelligence; however, each would be a part of intelligence in its own way. The prospects for the development of entities with AI have never been as good as they are now. The combination of advancements in computer hardware and software along with new insights into the ways in which we store knowledge and use it for problem solving has enhanced the potential for the creation of intelligent entities. After some unbounded optimism of a major breakthrough in the fifties and frustrating disappointments in the two following decades, it appears now that AI has emerged from research labs to industrial practice. This is confined by the growing number of repeat applications of AI in business and industry to the extent that AI can now be considered a technology.

Jan 1, 1989

By A. W. Khair

This paper presents an assessment of modeling techniques in predicting subsidence over longwall areas. Extensive instrumentation, both at the surface and subsurface of three longwall mines in northern West Virginia have been made. Ground movements were monitored during" a three year-period until subsidence ceased in these areas. A comparative analysis of empirical subsidence prediction techniques including, graphical {NCB}, profile function, influence functions (USBM, BAL&apos;S, KNOTHE&apos;S, and zone area) will be presented. A brief geologic and topographic description of each site along with the instrumentation and monitoring program will also be presented.

Jan 1, 1989