Search Documents

By Francisco Cubillos, Jorge Menacho, Cesar Gomez, Juan Rodríguez

Mineral flotation is the most used process to selectively separate particles of one or more minerals of interest. The process uses natural or induced hydrophobicity to collect particles on the surface of rising bubbles through collisions and formation of bubble-particle aggregates. Flotation machines must keep particles in suspension and well distributed, while at the same time, disperse a mass of air into a population of small bubbles. The efficiency of the separation depends primarily on the characteristics of the bubble population generated in the machine and its distribution and flow throughout its volume. The formation and separation of bubble-particle aggregates create two zones, with strong interactions between them, and with markedly different hydrodynamics conditions. A model describing two-phase hydrodynamics of the continuous and dispersed phases (frother solutions and bubbles, respectively), moving along the whole unit, is proposed. Bubble populations are characterized at the formation stage including the effect of the presence of frothers. Flow through the aggregates formation zone, where bubbles move freely and are closely spherical, is modeled using drift-flux analysis. In the aggregates separation zone, bubbles initially pack maintaining a water layer thick enough to prevent capillary forces to affect their shape. As water drainage proceeds, bubbles deform, capillary channels form, and a network of channels with a diameter size distribution develops; channels become narrower (permeability is reduced) as the distance from the interface increases. Froth hydrodynamics is characterized using models originally developed to describe unsaturated flow through porous solid particle beds. Effects of hydrostatic pressure are considered.

Jan 1, 2014

By W. H. Cheung

Nickel and cobalt production relies heavily on the processing of nickel laterite ores; these ores contain the majority of known Ni and Co reserves, 80% and 90% ~ 95%, respectively. The Caron process is used to extract Ni and Co metals from low-grade nickel laterite ores (1% Ni and 0.1% Co). It involves selective reduction of NiO and CoO minerals followed by ammoniacal leaching. Despite low metal recoveries, this process continues to be technically and economically reliable and thus commercially important globally. However, keeping the Caron process cost-effective has been a challenge for industries because of increasing economic and environmental pressures. Although studies of the Caron process have been extensive, significant improvements in recoveries of industrial processes have not been forthcoming. Reported industrial metal recovery from high iron content ore is only 80% ~ 85% for Ni and only 40% ~ 45% for Co; recovery is even lower for ores rich in magnesium. The real difficulty here is that there is no complete understanding of and control over the complex series of reactions in the ore and in the leaching solution during processing. Achieving effective metal recoveries from the Caron will require control of the mineral transformations, which affect the activation of minerals by reduction. In this study, the effect of over-reduction was investigated, which superseded the effect of activation by lowering the activity of the minerals and thus metal dissolution. Reduction was carried out in a batch reduction apparatus with 1:1 and 1:2.5 CO/CO2 gas mixtures from temperatures of 500 ~ 700°C and residence times up to 60 minutes. The pre-reduced ores were leached using a standard ammoniacal leaching test. Thermodynamic analysis and possible effects of stable phase field on leaching was examined. The results suggest that control of over reduction effects are directly related to the mineral transformation and reduction conditions.

Jan 1, 2014

By Zhenyang Wang, Xingle Liu, Xiangdong Xing, Shan Ren, Hongen Xie, Jianliang Zhang

"Non-isothermal combustion experiments of different additive amount of bituminous (0, 20, 40, 60, 80, 100 wt%) were conducted by synthesized thermogravimetry analyzer(STA409PC) from room temperature to 900°C in air. The changes of combustion characteristic parameters o f pulverized coals in different atmospheres are analyzed. The results show that DTG curves of coal combustion move to low temperature zones when the amount of bituminous increases. It indicates that both ignition and burnout temperature are lower, burnout time decreases, combustion characteristic index obviously increases, and combustion performance of blending coal are improved. The iso-conversional method involving Kissinger-Akah-Sunose (KAS) method was used for the kinetic analysis of the main combustion process. The results indicated that, when the additive amount of bituminous varied from 0 to 100 wt%, the value of activation energy which would sharply reduce if the additive amount of bituminous was under 60% increased from 133.94 kJ•mol-1 to 78.03 kJ•mol-1by using KAS method.IntroductionPulverized coal injection (PCI) to blast furnace (BF) is an important way for saving energy and reducing resource consumption during the ironmaking process. In order to acquire higher coal injection quantity, the relevant research topics in the field of pulverized coal combustion technology such as enhancing the efficiency of pulverized coal combustion, improving the combustion characteristics and reducing the harmful gas emissions and so on received extensive attention in recent years [1,2]. The combustion of blending coal when the appropriate proportion is selected for coal and also mixed well- distributed could give full play to the advantages of various types to make up the defects of single coal which is widely used throughout the world. So the blending coal injection to BF could produce a good impact on safety and economy for productive process. Therefore, a large amount of experimental researches on the combustion characteristic of blending coal for anthracite and bituminous were carried out by experts and scholars around the world [2-7].Nevertheless, the systematic research on the combustion behavior of anthracite with different content of bitumite in a thermogravimetric analyzer (TGA) is less. So in this paper, using the method of multiple scanning rate of conversion method, bituminous to promote the pulverized coal combustion reaction was studied to analyze its promotion mechanism of pulverized coal combustion reaction process, and the kinetic parameters of activation energy was also calculated, which to provide theoretical basis for the rationalization of resource utilization."

Jan 1, 2014

By Leon Lorenzen, Nursen Guresin, Harald Muller

The development of mining projects from discovery, exploration to actual production is a complex and time consuming process. Often poor process plant performance can be attributed to the use of non-representative samples and inadequate and/or unsuitable metallurgical test work when designing flow sheets during project feasibility study stages and specifying process equipment. Samples not representing the ore deposit and inadequate test work may lead to increased project development costs, since expensive test work and engineering may have to be repeated. It should be noted that for higher level engineering studies, larger scale test work is recommended and is a requirement for feasibility level studies. This would apply even if the technology is considered mature and well proven, as each ore body may have its own unique characteristics that, if untested at a larger scale, could result in significant design shortcomings, which will have to be rectified at later stages of the project, usually at significant additional costs

Jan 1, 2014

By António A. Henriques, António Gomes Correia, Ana Teixeira

"Abstract Pile foundations are often used for important structures, and thus, reliability evaluation is an important aspect of the design. Reliability methods have become increasingly important as decision support tools in different areas. The main benefit of reliability analysis is that it provides quantitative information about the parameters (uncertainties) that most significantly influence the behaviour under study. In particular, the design of pile foundations still involves many limitations and uncertainties, particularly when there is not enough investment in soil characterisation and/or pile load tests. In addition to the uncertainties associated with soil characterisation, physical, statistical, spatial and human uncertainties exist. In this subject, the primary purpose of this paper is to demonstrate the application of reliability methods to geotechnical pile design (axial load). It also presents a simple and practical approach to performing it using Monte Carlo Simulations, intending to provide knowledge for code harmonisation and encouraging the development of such methodologies in geotechnical practice. Sensitivity analyses are shown to understand the influence of each uncertainty type coming from different sources. An application example indicates, corroborating other studies, that the model error is the most influent uncertainty. As such, when using the different models (SPT-, CPT- and PMT-based) for bearing capacity, the results emphasise the need for a well-defined and wellcharacterised resistance model, also these results allow the engineer to understand how important the load tests can be to achieve reliable results and economic designs.1 IntroductionUnlike the approach to reliability evaluation used in structural engineering, the traditional procedure used in geotechnical designs addresses uncertainties through high global or partial safety factors (SF), mostly based on past experience. However, this approach to addressing uncertainties does not provide a rational basis for understanding their influence on design.Furthermore, the new regulation codes and social concerns, such as the sustainability or the economy, are imposing geotechnical engineers to increase their ability to deal with uncertainty in a direct and more rational way. Designs should be economic, sustainable and reliable at the same time. Concerning the reliability part of design, different approaches can be done, but the most important thing to keep in mind is the simplicity and efficiency of the tools and applied methods."

Jan 1, 2014

By Mario Gerards, Sergej Podkow, Marco Steinberg

"The JONES® WHIMS technology is based on the magnetic separation process and is widely used for the recovery of magnetically susceptible iron ore particles. The conventional machine design is well-known within the iron ore beneficiation industry for more than 50 years and recognized to be highly reliable, robust and extremely compact with the advantages of high capacity and selectivity. In 1981 Rana Gruber AS, Norway bought 14 JONES® WHIMS DP 317 separators when the magnetic separation plant was built and erected. Today, 11 of these old machines are still operating profitably and efficiently. The former supplier was the coal and minerals division of Klöckner-Humboldt-Deutz (KHD) which is today MBE Coal & Minerals Technology GmbH (MBE). This paper outlines a detailed description of the project of revamping the above mentioned old machines and describes the challenge of incorporating enhanced and newly developed technology into an existing processing plant. Further it gives an overview of the recent developments on the design of the JONES® WHIMS. In order to meet modern product requirements and to increase and secure plant productivity, in 2012 Rana Gruber AS settled a contract covering two new designed JONES® WHIMS DP 317 HFR separators to be implemented into the existing building and the upgrading of all 11 older JONES® WHIMS under the use of as many refurbished items as possible. The two new machines were fully developed by the product specialists of the supplier in cooperation with the operator Rana Gruber AS, thereby taking advantage of their great experience. The design of the new machine is based on the conventional design, i.e. the general operating mode as well as the overall dimensions are identical. Finally this paper gives an overview about the erection and commission phase of the two new machines and gives a detailed comparison between conventional and enhanced WHIMS technology."

Jan 1, 2014

By M. Taheri

Multiple Attribute Decision Making (MADM) method is applied to select tailings site of the Gol-e-Gohar Iron Ore Processing Plant in the Kerman province, south-eastern of Iran. To select tailings site, screening is applied on eight location proposed by Binnie and Granges. Consequently three sites identified for further studies. Evaluation factors include only the most important factors such as efficiency ratio, elevation and distance to processing facilities, occurrence of faults and fractures. Crisp values such as efficiency ratio, elevation and distance can be determined by measurements and calculations, but some factors such as occurrence of faults and fractures are presented as linguistic values that can be described with triangular fuzzy numbers. Based on evaluation values obtained an optimal tailings site can be selected using a modified Technique of ranking Preferences by Similarity to the Ideal Solution (TOPSIS) given crisp data and linguistic variables as the alternatives of attributes. Each attribute?s weight is assigned using the analytic hierarchy process. The final ranking order aids in the selection of tailings site. Finally, the stages of modified TOPSIS method were applied and site No.2 situated in 5400m to the mill was selected as the best alternative.

Jan 1, 2014

By I. Baltov

The Chelopech Mine, located in Central Bulgaria, is one of Europe?s largest underground copper- gold mines, currently mines and processes approximately one million tonnes of ore per year. Copper concentrates containing gold and silver with significant arsenic content are produced and sold on the world markets. The operation was acquired by Dundee Precious Metals in 2003. A modernization program for the Mine and Plant has since been in progress to increase both production and mechanical reliability, and also to optimize metallurgical recoveries. Since then, mine output and plant throughput have doubled, plant availabilities and utilization have increased significantly, and overall metallurgical performance for copper and gold improved. The paper presents the systematic approach for obtaining and analyzing data, communicating it, and making suggestions for changes to the technological parameters and flowsheet in order to maximize metal recoveries. These studies have correlated the ore characteristics (particle size distributions, metal assays, and Cu and Au mineralogical and phase analyses) with the actual plant performance (kinetics, recoveries, and throughput). Cu recovery by size has been calculated from the mineralogical analyses of feed, concentrate and tails, with the most significant losses being identified in terms of fraction and phase recoveries. This has provided the recommendations (some of them tested in plant) for changes in the grinding and flotation circuits.

Jan 1, 2014

The objective of the paper is to develop a material balance calculation procedure for a production unit involving two plants separated by a pipeline. The case study is taken from the oil sands industry. The raw sands are first mixed with water in a conditioning plant, then transported through a pipeline to an oil extraction plant. The combination of pipeline dimensions and nominal throughput creates a significant variable time lag between the two plants. As usual, mass balance calculations required for the evaluation of plant performance indicators, such as bitumen recovery, are inaccurate due to measurement errors. In addition, in the present case study, the time lag of the pipe creates an additional source of uncertainty, which may lead to misinterpretations and wrong decisions. Raw data are usually reconciled through steady-state mass balancing, to correct for measurement errors. However, because of the significant pipeline dynamic lag, standard steady-state daily mass balance may fail at giving an appropriate picture of the operations. The proposed solution to the data reconciliation problem includes the use of a pipeline plug-flow model in the mass balance calculation. To fulfil the industrial constraint that current data reconciliation must not modify past reconciled values, while still satisfying dynamic constraints, a daily one-step method, i.e. a unitary filter-ing horizon, is recommended. The method is illustrated with simulation data, and the results com-pared to those of standard data reconciliation methods.

Jan 1, 2014

By P. K. Fedotov

At projecting mining-concentrating complex at the deposit ?Zapadnoye? (Russia) it was considered to enable an opportunity of refusal from conventional SAG-mills. First time a scheme of gold bearing ore destruction using Roller Press RP 5-100/90 had been developed and integrated. The plant was launched in summer 2003 and presently it has achieved designed technological parameters, processing throughput comes to 1 million tons of the ore per year.

Jan 1, 2014

By Per Svedensten

One of the most significant behaviour of a crushing plant is the constant variation in the process. The variation is caused by two major effects. The first and constantly changing is the rock material properties. During operation rock material with different strength and particle size distribution is fed to the plant which makes the performance of the equipment to vary. The second and more slowly changing variation is caused by wear on the processing equipment. These effects must be predicted in order to be able to optimise a crushing plant. This paper demonstrates how Monte Carlo simulation can be utilised to study and operate crush-ing plants. By introducing Monte Carlo simulation the varying process can be study and also optimised. To maintain the optimised process performance supervision is needed. This paper demonstrates how results from the Monte Carlo simulation can be utilised for process supervision. Charts for process measurements can for example be derived. These can then be used to guide decision making and understand how the variation and performance of the plant changes over time.

Jan 1, 2014

By Carlos de F. Gontijo

The flotation of quartz particles was studied over the particle size range from 0.5 µm to 1000 µm and for advancing water contact angles between 0º and 83º. Flotation was performed in a column and in a Rushton turbine cell. Particle contact angle threshold values, below which the particles could not be floated, were identified for the particle size range 0.5~1000 µm, under different hydrodynamic conditions. The flotation response of the particles, either in a column or in a mechanically agitated cell with a similar bubble size, was comparable. Turbulence plays a role, as does bubble-particle aggregate velocity and bubble size. The stability of the bubble-particle aggregate controls the maximum floatable particle size of coarse particles. For fine particles, the flotation limit is dictated by the energy required to rupture the intervening liquid film between the particle and bubble. Flotation of very fine and large particles is facilitated with small bubbles and high contact angles. These results greatly extend our earlier observations and theoretical predictions.

Jan 1, 2014

By Ali Naeimipour

Availability of accurate geological information about the rock mass surrounding a tunnel or mine working is the key to enhance and optimize the required ground support measures. Various approaches have been used to obtain data on ground conditions, including the possibility of characterizing the ground while drilling for roof bolts, by the Measurement While Drilling (MWD) system, via optical, sonic and acoustic televiewers, and using various types of gamma probes. While there are many different systems for characterizing the ground in longer, larger-diameter holes drilled downward, the options for using probes and logging systems in short, small-diameter holes drilled in horizontal or an upward direction are very limited. This paper will present the results of recent field tests using optical televiewer (OPTV) to analyze the joints and voids in boreholes drilled in different directions. The studies show that OPTV is a promising tool; however, getting a good quality image from the upward drill holes still need to be studied. Meanwhile, estimated in-situ strength of the intact rock is needed to complement the jointing pattern for rock mass classification. For this purpose, preliminary steps for the development of a borehole scratcher to estimate rock strength will be discussed in this paper.

Jan 1, 2014

Compressive crushing is applied in crushing plants used in mineral, mining, and aggregate in-dustry for fragmentation of rock materials. From a global perspective, the total volume of crushed rock is massive and corresponds to several billion tons. All societies have to fulfil a daily need of rock material products and its derivatives such as metals and minerals. The business for metals and minerals is global while the aggregates production is mainly a local industry. This paper presents a broader overview of optimisation with respect to product yield, use of natural resources and energy consumption. High level plant optimisation of compressive crushing plants is covered as well as real-time optimisation and optimisation of single production units. Each of three optimisation areas are presented and a discussion around how these three areas will be able to communicate with each other is given. Several models, e.g. process performance behav-iour with respect to wear, as well as fitness functions can be common for all three areas. Well-defined and representative fitness functions are of the utmost importance in order to assure that the optimisation results reflect the production targets. It is concluded that great benefits can be achieved by linking together different areas of optimisa-tion. The future for compressing crushing lies, without a doubt, in tailored processes both with re-spect to machines optimised for each customer, plant parameters and operation routines as well as an on-line adjustment, which takes into account current information and control possibilities.

Jan 1, 2014

By David Yang

Commercially available flotation technologies for recovery of mineral fines have remained essentially unchanged for several decades. Recent studies have focused simply on improving mechanical and open column cells. Such studies have explored different control strategies and have aimed to improve reagent selectivity, fine air bubble generation and particle-air contact. However, no study has questioned whether current techniques are the most efficient technology for recovering mineral fines. Given that both mechanical and open column cells have a widely accepted carrying capacity limitation, the lack of extensive research into an alternative technology is surprising. Most recently, open column flotation has become an entrenched technology, and it is undermining the efficient recovery of mineral fines worldwide. An alternative exists. Packed column flotation overcomes the above-stated problems as the technology surpasses the carrying capacity limitation of current means by several-fold and almost always achieves the best performance in many comparative pilot tests and full-scale plant operations. Filling a column with packing plates creates a network of sloped walls capable of supporting a froth bed many times deeper than conventional machines. Having froth up to 75 percent of the total column volume tolerates all feed changes encountered in the plant environment and permits maximum flexibility in concentrate quality control. Furthermore, its scale-up is straightforward by increasing column volume or the number of interconnected small cells. As the air breaks upon rising and is distributed horizontally through packing plates, the air spargers can be replaced with a simple blower, resulting in considerable savings in operation and maintenance costs. Packed flotation technology provides a break-through solution for the separation of fine and ultra-fine minerals. Its simplicity, superior performance, and low cost structure make it an appealing alternative to current technologies and allow greater flexibility in downstream processing. Future industrial applications include a wide variety of metallic and non-metallic ores. This paper focuses on some recent scale-up campaigns for nickel and copper sulphide flotation applications compared directly to conventional equipment.

Jan 1, 2014

By Ramdane Bahar

"Abstract The design foundations can be performed using Menard pressuremeter rules that require a limit pressure and a pressuremeter modulus. In recent years, another trend of interpretation of this test is appeared. It consists of identifying the rheological soil parameters using analytical or numerical methods and then used to evaluate the bearing capacity and settlement of soil foundations using numerical software. This paper deals with the bearing capacity and settlement predictions of bored piles using two approaches. The first one is the method called ""Pressident"" which is a numerical program developed to analyse pressuremeter tests taking into account the Duncan and Chang model. The second approach is the method developed by Bahar and Olivari based on the generalised elastoplastic Prager’s model with the Von Mises criterion which is suitable to describe the behaviour of saturated clays under undrained conditions. The pressuremeter data, collected on various research and consulting projects are used to explore the relationship between limit pressure and undrained shear strength obtained by the two methods. Numerical calculations, by FLAC2D software taking into account the rheological parameters derived from these two methods, are performed in order to predict the behaviour of a single bored pile subjected to an axial vertical load. The predictions are comparedto the measured data.IntroductionThe Menard Pressuremeter test has been used extensively to measure in situ soil properties and for the design deep foundations in Algeria. These tests are an useful and economical way for obtaining reliable in situ properties of soils and provide the measurement of in situ stress-strain response of soils. From this test, the design foundations can be performed using pressuremeter rules that require a limit pressure, pl, and a pressuremeter modulus, EM. These two parameters are derived from the pressuremeter curve or deduced from existing correlations with undrained cohesion and internal angle friction (Ménard, 1957; Amar and Jézéquel, 1972), and are used to evaluate the bearing capacity of soil foundations and the expected settlements. But, they can also help to identify usual soil parameters required by simple constitutive models for soils in numerical calculations."

Jan 1, 2014

During heap leaching of secondary copper sulphide ores operated at low heap temperatures and high levels of leach solution salinity, copper recovery is usually unsatisfactory, due to a slow chemical and bacteriological leaching of the covellite minerals either formed from leaching of chalcocite or naturally occurring in ores. A laboratory test program was conducted to investigate the effect of leach solution temperature in the range of 20 to 50°C on copper extraction during stirred reactor, bottle roll, and short column leaching of fresh or heap leached secondary copper sulphide ores. It was demonstrated that increasing heap temperature is an effective approach for improving recovery of copper from secondary copper sulphide ores. A review of the technologies available for heating heap leach solution or decreasing solution salinity to improve copper recovery from secondary sulphide ore indicates that an integration of copper concentrate pressure leaching with heap leaching is potentially a cost-effective approach. A copper flotation concentrate sample was tested through pressure oxidation with the use of heap leach solutions of varying strengths for the repulping of the concentrate in order to examine its effect on pressure oxidation performance. The test results indicate that use of heap leach solution of high salinity in the pressure oxidation process does not cause a negative impact on the process performance for copper extraction, sulphide oxidation, and recovery of gold (if present) from pressure leach residue, and has additional advantages of removing the bacterially inhibitory aluminum from heap leach solution and generating more acid and ferric iron in the pregnant leach solution. A flowsheet configuration for full integration of the copper concentrate pressure oxidation with heap leaching of secondary copper sulphide ore is proposed and discussed.

Jan 1, 2014

By Paul Gottlieb

This paper reviews the status of automated applied mineralogy today and describes the history and fundamental theoretical and practical bases underpinning the development of automated systems. Details are given of the technical challenges that were faced in creating the new technology and in applying it to a range of applications. In recent years, automated mineralogy has become established as an essential enabling technology for the reliable acquisition of statistically sound comprehensive mineralogical and metallurgical data. This has had a revolutionary effect on the industrial use of such data in the study of geology, mining and mineral processing. Previously, using manual methods, it was not feasible to attempt this work because the large data sets required could not be assembled in a realistic timescale. There was a reliance on individual expert mineralogists and this was not scalable. The speed, reliability, detail and repeatability of the modern automated measurements has now made this type of analysis routine. Automated Applied Mineralogy has come of age! More than 100 systems have been installed around the World. Automated mineralogical analysers such as QEMSCAN® were originally developed as diagnostic metallurgical tools to improve mineral processing plants using samples drawn from plant surveys, bench and pilot-scale tests. They were used mainly for the assessment and auditing of size fractions of mill products, such as concentrates and tails. Subsequently, they began to be used for concentrator design and optimisation where ore characterisation was used to help understand the relationship between the feed ore and its subsequent behaviour in the plant. They are now widely used to measure exploration cores and drill chips from drilling programs to predict eventual metallurgical performance. Ore samples can be classified into metallurgical, as well as geological types, by combining mineralogical features in the ores with metallurgical properties related to grade control, separation, comminution, flotation and leaching behaviour. Three-dimensional block models of ore deposits are now being created based on processing response in addition to geological and mining properties. The development of automated systems began in Australia, the United Kingdom and Canada in the late 1970s and early 1980s. There were many technical challenges. Mathematical theories of randomness, sampling theory, image analysis and stereology were developed to ensure sample representivity so that meaningful information could be obtained. Sample preparation, presentation and measurement methods were developed to ensure that the random sampling was preserved during the measurements. Methods of automatic measurement and mineral identification evolved from the use of electron microscopes, fitted with backscattered electron brightness and energy dispersive X-ray detectors. Operational procedures were required to ensure that these instruments could accommodate a large number of samples and operate unattended for long periods of time. The new technology was progressively applied to a range of commodities and applications and new analysis methods, such as liberation measurement, were needed for metallurgical interpretation of mineralogical data.

Jan 1, 2014

By Y. Gordon

ABSTRACT A methodology based on a two-stage approach was developed for process technology selection. The first stage includes evaluation of available technologies, followed by shortlisting the best technologies based on mass and energy balance modelling, financial analysis, and risk analysis. The second stage involves detailed analysis using refined input data, mass and energy balance modelling, and capital and operating cost estimation, as well as a more detailed financial analysis. A case study covering the selection of ironmaking technologies for a company in the Russian Federation is presented to illustrate the critical elements of the methodology and the analysis process.

Jan 1, 2014

By J. C. Vreugdenburg, B. A. Dippenaar, J. Muller, T. L. de Vries

Iron ore fines are agglomerated in the sintering process to produce sinter: an important feed material for blast furnaces worldwide. A model of the iron ore sintering process has been developed with the objective of being representative of the sinter pot test, the standard laboratory process in which the behaviour of specific sinter feed mixtures is evaluated. The model aims to predict sinter quality, including chemical quality and physical strength, as well as key sinter process performance parameters such as production rate and fuel consumption rate. The model uses the finite difference method (FDM) to solve heat and mass distributions within the sinter pot over the sinter bed height and time dimensions. This method can further be used for establishing empirical relationships with measured sinter properties. Inputs into the model include the feed material physical properties, chemical compositions, and boundary conditions that vary over time. Sub-models describe relationships between applied pressure differential and gas flow rate through the bed of granulated fine ore particles, combustion of carbonaceous material, calcination of fluxes, evaporation and condensation of water, and melting and solidification. Four sinter pot tests were performed and the model predictions validated against temperatures measured at depths of 100, 230, and 420 mm. Differences between predicted and measured temperatures indicated the need for optimization of some model parameters that are uncertain. Optimization resulted in an improvement in the correlation between the predicted and measured temperatures for all tests, although an acceptable level of agreement was not achieved in all cases. Using these parameter values, reasonable agreement was found in terms of typical performance parameters for three out of the four tests.

Jan 1, 2014