Search Documents

By U Briem, R Verreet

The level of wire rope technology used in mine hoisting applications has a significant effect on the overall efficiency of the hoisting system. This paper discusses the effect that a reduction in rope mass per unit length and an increase in rope breaking strength can have on rock skip capacity and hence mine shaft output. A 20 per cent reduction in rope mass per metre for a typical 48 mm hoisting rope, while maintaining the breaking strength, increases the skipÆs capacity by circa 30 per cent at a suspended rope length of 3000 m. Such gains in shaft output, without any significant changes to the shaft or winder design, can have major implications for the feasibility of future deep mine projects. The technical challenge for rope manufacturers is how to get rid of 20 to 30 per cent of the rope mass while keeping the breaking strength and modulus of elasticity of the whole rope constant. CASAR are currently developing steel wire rope constructions where the steel IWRC has been replaced with high strength, high modulus fibres such as Kevlar«, Spectra« and Dyneema«. One of the key aspects of such composite rope designs is to ensure equal load sharing between the different rope components, ie in proportion to their area. If there is a significant difference in modulus between the fibre core and the steel outer strands, the core may not carry its proper proportion of the load and the outer strands would be overloaded. Some technical aspects of the design of composite steel wire ropes are discussed. A design and operational issue that needs careful consideration is the safe non destructive testing (NDT) of composite ropes. Traditional magnetic NDT would only be capable of inspecting the steel wires. Techniques therefore need to be developed that would give operators a reliable indication of the condition of the load bearing fibre core. This paper also discusses possible solutions to this very important NDT question.

Jan 1, 2005

By G V. R Goodman, G J. Chekan, J M. Listak

The extraction and transport of coal from underground coal mines can result in significant liberation of coal and/or silica dust into the mine atmosphere. Mine operators have long used ventilating air as a primary means of diluting generated dust, removing dust from the working faces and preventing dust from reaching the minersÆ working environment. As production levels have increased, mine operators continue to be challenged in maintaining dust concentrations below compliance levels. The need for maximising the effectiveness of available ventilating air in conjunction with other effective controls, such as water sprays and dust collectors, continues to be critical to the long-term health of mine workers. The National Institute for Occupational Safety and Health (NIOSH) has conducted full-scale laboratory and mine-site research to evaluate improved application of dust controls for both longwall and continuous mining methods. A summary of recent research results and recommended practices will be provided.

Jan 1, 2005

By I. Kirman, B. Waters

World wide applications for nickel use will be summarized and examples of those uses given. Nickel products are critical to many important aspects of modern society. These products are just as important for modern China as they are in other parts of the world. It is argued that future pattern of nickel use in China should be expected to be very similar to that in the rest of the developed world. Total use of nickel in products in China is already very large. In 2004, it was the largest market for stainless steel (nickel containing) in the world. A survey of Chinese stainless steel applications will be presented. Current high nickel prices have revived speculation about substitution, particularly for nickel containing stainless steels. The presentation will discuss some of the complicating factors that need to be taken into account when considering substitution. These factors are as valid in modern China as they are in other developed economies. Recent substitution efforts and the reaction to them will be examined. The Nickel Institute position regarding appropriate application of the various grades of stainless steel will be discussed. Price-motivated substitution in China, and elsewhere, will occur but it is argued that the extent will probably be limited.

Jan 1, 2005

By Laurence G. Britton

Accurate flammability and ignitability data for chemicals form the cornerstone of procedures used to assess the hazards associated with commercial chemical production and use. Since 1967 the ASTM E27 Committee on the Hazard Potential of Chemicals has issued numerous, widely used consensus standards dealing with diverse testing and predictive procedures used to obtain relevant chemical hazard properties. The decision to issue a standard rests solely with the membership, which consists of representatives from industry, testing laboratories, consulting firms, government, academia, and instrument suppliers. Consequently, the procedures are automatically relevant, timely, and widely applicable. The purpose of this paper is to highlight some of the widely used standards, complemented with hypothetical but relevant examples describing the testing strategy, interpretation, and application of the results. A further goal of this paper is to encourage participation in the consensus standards development process. The paper is published in two parts. The first part (in the preceding issue of Process Safety Progress) dealt with the E27 standards pertaining to thermodynamics, thermal stability, and chemical compatibility. The second part, published here, focuses on the flammability, ignitability, and explosibility of fuel and air mixtures. © 2005 American Institute of Chemical Engineers Process Saf Prog 24: 12?28, 2005

Jan 1, 2005

By N. Djilali

Many of the transport phenomena encountered in proton exchange membrane fuel cells occur intrinsically at the microscale level. Physically representative models that fully account for the salient physico-chemical and transport processes in PEM fuel cells are necessary to achieve truly predictive models that can be used with confidence to: (i) gain a better understanding of in-situ processes and couplings, (ii) explore new concepts, and (iii) support design and optimization. The development of more general, rationally based macroscale models requires use of knowledge on the microscale level to provide guidance, and to determine the required parameters and coefficients (model "constants"). In this paper we present a new membrane transport model, the binary friction membrane model (BFM2), recently developed to account for coupled protonic and water transport in polymer membranes. This general model is based on rational and physical consideration, removes several of the limitations of the empirical models used to date, and is formulated for all purfluoro-sulfonic acid membranes. The use of the BFM2 in a fuel cell model is illustrated highlighting significant performance predictions compared to existing empirical model. The second part of the paper addresses the fundamentals of two-phase transport in hydrophobic gad diffusion media. Computational and experimental visualizations resolving the microscale dynamics of water transport between the fibres of a GDL are presented, revealing transport mechanisms that are, contrary to assumptions used to date, dominated by fingering and channeling.

Jan 1, 2005

By M. Greyling, C. Panaou, M. Bellino

Commonly the most frequent method of calculating the overall mass balance of a multi mineral platinum-group metal (PGM) concentrator circuit in Southern Africa has been through the use of spreadsheets, typically Microsoft EXCEL®. While there are some advantages in using spreadsheet based mass balances during the conceptual design phase of the project, their use becomes limited in the detailed design phase of the project. This paper discusses the successful application of METSIM® for mass balancing of a PGM concentrator and highlights the benefits gained during the conceptual and design phase of the project.

Jan 1, 2005

By J. I. Gazzarri

A model of solid oxide fuel cell AC impedance behaviour has been developed and is used to simulate the frequency response of a single cell with and without mechanical damage. The results indicate that the presence of mechanically induced damage within the components of a solid oxide fuel cell can be detected by comparing the frequency response of the undamaged cell with that of a cell in which in-plane cracking or delamination has occurred. The presence of such defects manifests itself as a new semicircle in the Nyquist impedance diagram of the full cell. A parametric study reveals the resolution capabilities of the method in terms of the geometrical characteristics of the defects.

Jan 1, 2005

By R E. Hobbs, O Grabandt, C Das

Mine hoisting is carried out from depths of up to 4 km. At extreme depths, the ropes are so heavy that a large part of their capacity is employed in lifting themselves. Consequently, deep mines have an intermediate winding station. Even at lesser depths, the weight of steel wire rope reduces the possible payload. Of course, steel wire ropes have, over the years, demonstrated exceptional reliability and acceptable lifetimes. The use of steel is supported by well established operating rules and sound NDT methods. However, lightweight ropes made from synthetic fibres could be of great benefit to the industry, with the prospect of eliminating two-stage winding and substantially increasing the payload. Initial tests, in cycling over sheaves, have demonstrated that an aramid co-polymer fibre, Technora« is a potential candidate for this type of service. This paper presents results of testing carried out on aramid co-polymer and other synthetic fibre ropes. These results hold out the prospect of exceptionally long lives. Possible NDT methods are explored including optical fibres with optical time domain reflectometry or with Brillouin scattering, plus a method based on carbon fibre continuity. The introduction of aramid co-polymer ropes will require extensive testing and a program is proposed in the format of a Joint Industry Project.

Jan 1, 2005

Alfred Nobel first invented a practical detonator in 1863 and then the blasting cap in 1865. At that time the detonator was used on the end of a length of safety fuse to initiate nitroglycerine-based explosives. Since then the detonator has gone through a number of changes. The instantaneous electric detonator was the first to allow remote firing. The electric delay detonator followed and allowed for timing between holes. In the mid 1970s the NONEL« Tube was invented. This tube combined with NONEL« detonators meant that many of the safety issues, such as stray current and radio frequency, associated with electric delay detonators were eliminated. This system gave the mining industry a reliable and fairly accurate system with which to detonate shots of any size. Since the early 1980s a large amount of research and development work has been done around the world to create a more accurate detonator for the mining and quarrying industry. After years of research, electronic detonators have emerged as the most accurate and precise initiation system available to the mining and quarry industry today. Electronics provide the user with millisecond timing accuracy. The improved level of timing control allows operations to improve fragmentation, throw and reduce vibration levels. There are now a number of different electronic detonator suppliers on the market today. In 2004 Dyno Nobel formed a joint venture called DetNet with AECI. DetNet has a suite of electronic detonators: DigiDet«, HotShot« and QuickShot«. This paper will focus on the HotShot« system, the first of the three new initiation systems to be released to the market in Australia by Dyno Nobel.

Jan 1, 2005

Sheaves are a critical safety component in a winding system and are expected to survive such extreme loading events as rope break. Sheave designs have often been developed and evolved empirically, consequently many existing sheaves are not necessarily subjected to the detailed analyses that are possible using todayÆs design tools. The design philosophy for sheaves is that the rope should be the weakest link in the system so that associated equipment can function safely for any load up to rope break. A number of failure mechanisms must be considered, but buckling is often prominent. During the course of investigating the feasibility of upgrading the hoisting capacity of a winding system, the capacity of all critical components was reviewed. The sheaves in the system were found to have insufficient spoke buckling capacity for the specified rope. A proposal to increase the spoke buckling capacity by connecting spokes together using a simple tie arrangement was evaluated and found ineffective. An alternative tie arrangement concept was developed and evaluated and shown to be adequate. This paper describes the finite element model, analysis approach and results for the original sheave and the two modifications. The contribution of the sheave rim to the total buckling capacity is evaluated. Some practical issues for spoke tie modifications are discussed.

Jan 1, 2005

By B. Kenney

For SOFCs, composite cathodes comprising an electronically conducting electro¬catalyst (e.g. LSM) and an conically conducting electrolyte material (e.g. YSZ) are considered to improve the electrochemical performance by extending the active reaction zone to regions beyond the electrolyte-electrode interface, as in the case of conventional cathodes. Interpretation of experimental data for composite cathodes, however, is complicated by the mixed conducting behaviour which results in local overpotential distributions throughout the composite cathode. These local overpotentials depend on many factors, such as the composition, particle size, porosity and thickness of the cathode. Reliable experimental data obtained from composite cathodes requires carefully crafted microstructural parameters in order to minimize the overpotential variations. A mathematical model of a composite cathode was developed using coupled differential equations describing transport and consumption of chemical species, oxygen ion and electrons. Simulations under various oxygen concentrations were used to obtain the reaction order of the oxygen reduction reaction. An apparent po2 dependency was then extracted from the predicted Rp vs P02 data. It was found that this p02 dependency can be significantly influenced by the micro-structural parameters of a composite cathode, primarily due to local overpotential distributions.

Jan 1, 2005

The control system of a mine winder or other variable speed drive has many component parts that must work together to provide the required functional performance of the machine, together with comprehensive safety features, reliability, maintainability, user-friendliness and efficiency. Modern winders use digital control technology extensively and hence software design is a major part of the overall system. It is not practical to simulate an entire mine winder in a single computer model because of the sheer mathematical complexity of the behaviour of many of the components. However, most component parts can be simulated quite easily, and related parts of the control system software can be simulated. Such simulations allow control software algorithms to be developed and tested in isolation from the real plant. Tests can be performed on the model without fear of injury to personnel or damage to the valuable plant. For example, speed regulator control algorithms and stability settings can be adjusted to and beyond the limits of stable operation, and near optimum settings can be found. This is particularly important, for example, when designing closed loop controls for emergency brake systems. Obviously, care must be taken to ensure that the computer model of the plant is realistic and takes into account as many non-linear features of the real plant as possible. Pure mathematical analysis of some systems is very difficult to perform when non-linear plant behaviour is involved. This paper shares a number of practical simulation experiences performed using commercially available software such as Matlab and Simulink to simulate various parts of the control system of a mine winder or other variable speed drive. Demonstrations of the operation of several different computer models are shown during the presentation of the paper.

Jan 1, 2005

By C. Gu

Flow field design is critical for PEM fuel cells. The flow field design can affect reactant distribution to the catalyst surface, water management, thermal management and current collection. Therefore, it has tremendous impacts on the fuel cell performance and durability as well as reliability and operational flexibility. In this paper, an optical method is used to study the reactant distribution in the flow field channels of two commonly used flow field designs, straight channel design and serpentine channel design. Images of the flow patterns are shown followed by discussions of the flow patterns.

Jan 1, 2005

By D. V. Dorling, J. T. Bowker, J. A. Gianetto

Over the last few years, interest in the development and construction of large diameter, high pressure pipelines from the Mackenzie Delta in northern Canada and Alaska's North Slope has steadily increased as a result of the projected decline in recoverable natural gas from existing reserves in western Canada. The success of such enormous pipeline projects, which will require utilization of a strain-based design approach, is largely based on successful application of high strength line pipe steels, such as X80 and X100. To fully realize the economic benefits of high strength steels, welding processes and procedures must be developed to ensure that the requirements for high strength and good low temperature toughness are confidently obtainable in field girth welds used in the construction of such pipelines. This study aims to provide a better understanding of the factors that control weld metal strength and toughness for a series of mechanized X100 girth welds produced using a range of narrow-gap gas-metal arc welding procedures. The attainment of high yield strength (> 810 MPa) is considered to be an important target to ensure overmatching strength relative to the longitudinal property distribution of X100 line pipe steel. Some factors that have been considered in this evaluation include influences of gas-metal arc welding process variants (single and multi-wire) and changes in welding procedure specifications, including joint preparation. Key components of this work relate to the reliable measurement of weld metal strength variation through-thickness and as a function of position around the circumference of a given girth weld.

Jan 1, 2005

Reliable sampling practices are the key to optimising the market value of a mining or chemical companyÆs stock. As a result, reliable sampling standards are needed. However, current standards on sampling present the æuniversalÆ Pierre GyÆs Sampling Theory in an ambiguous way. For example, the Total Sampling Error is divided into its basic components only in informative annexes, when it should clearly be the main body of the standard. Sampling standards are presently loaded with statistical concepts that actually belong in the annexes. Furthermore, many non-probabilistic sampling procedures are still mentioned which do not belong in a standard. The objective is not to criticise existing sampling standards, but to suggest better ones. Sections on the Sampling Theory should divide the Total Sampling Error into a sum of its nine basic components. Then, and only then, should they be addressed one at the time. Sections for establishing a sampling protocol should address the in situ Nugget Effect, the Fundamental Error, the Grouping and Segregation Error, the Long Range Quality Fluctuation Error, and the Periodic Quality Fluctuation Error. Sections for sampling methods, mechanical sampling, manual sampling, grab sampling, sampling of trucks, railroad cars, bags, and drums should be part of the critically important practical implementation of a recommended sampling protocol, called Sampling Correctness. It includes the increment Delimitation Error, the increment Extraction Error, the Weighting Error, and the Preparation Errors. Unless these errors are addressed one at a time, in an unambiguous way, the standard will remain ineffective in solving sampling problems for the industry. Therefore, a strategy is needed to create better standards required at the early stages of new projects, both by manufacturers of sampling equipment and by engineering firms. A logical sequence of important points that cannot be ignored in any sampling standard is presented. An analysis of the practical use of the words sampling uncertainty versus sampling error is recalled. Finally, as a practical example, an in-depth analysis of the correctness of cross-belt samplers is presented, and emphasis is placed on the correct ways to perform bias-tests for mechanical sampling systems.

Jan 1, 2005

For the last few years, a new and innovative technique has been successfully used to determine refractory and castable thickness in various metallurgical vessels. The acousto ultrasonic-echo (AU-E) technique uses stress waves to detect metal penetration and delaminations within refractory linings. In addition, it is capable of measuring the thickness of refractory layers and build-up material. The inspection and measurements can be carried out while the furnace is in full operation. The present paper discusses the principles of the AU-E technique, and its advantages and limitations. A number of case studies are presented to demonstrate various capabilities of this new Non-Destructive Testing (NDT) technique.

Jan 1, 2005

By F. Stober, D. Wanblad, J. Ndlovu, L. R. Nelson, L. P. S. de Villiers

The single six-in-line furnace of the Polokwane Smelter is the largest installed high-intensity furnace for platinum group metals (PGM) base metals sulphide smelting in the world. The furnace employs state-of-the art technology to deliver a planned throughput of 650 000 t/a dry concentrate at a design 68 MW power input. This furnace, at double the capacity of previously existing PGM furnaces, offers low unit operating and capital cost through the resulting economies of scale. Key features of the design include:

Jan 1, 2005

Although AustraliaÆs coal mining industry is currently experiencing a pleasing period of price relief, long-term trends toward lower real prices will surely continue. Higher price levels attract expansion by existing operators and market entrance by new operators. History clearly demonstrates the relentless long-term march toward ever lower real prices. Therefore, the need for economic returns applies constant pressure to improve productivity. To be sustained, high productivity requires a systematic response based on a solid understanding of critical productivity determinants. The most powerful determinant of productivity is now widely understood to be workplace culture. Culture largely comprises a combination of behaviours, symbols and attitudes. This paper will examine and review scienceÆs latest discoveries in human behaviour. It will provide a proven, practical framework for understanding behaviour and applying this knowledge. Significantly, it will highlight why conventional approaches toward improving productivity often provide disappointing economic returns. The modern understanding of behaviour factors will cover coal face operations. More importantly, because executive and managerial levels in coal mining have significantly greater impact on industry and mine productivity the paper will concentrate on leadership. Particular emphasis will be placed on use of modern systems and in particular use of what are by far the most powerful drivers of behaviours û measurement, analysis and reporting systems. The paper and presentation will show how conventional systems rooted in antiquated American legislation from the early 1900s stifle productivity improvement and drive suboptimal and even counterproductive behaviours. These commonly used systems will be compared with accurate and effective modern methods for assessing performance to improve productivity. These principles are proven in all industries and effective application in mining will be highlighted. Actual results will be used to demonstrate practical approaches successfully applied in both metal and coal mining in Australia and overseas.

Jan 1, 2005

By A. J. Makoka, B. C. Qi

Reliable monitoring of corrosion is vitally important in the combat against corrosion and over the last two decades the interpretation of electrochemical noise has received considerable attention as a means to discriminate between different types of corrosion. To this end, many different analytical methods have been proposed, such as power spectral density analysis and analysis via various other stochastic criteria. However, although many corrosion systems are nonlinear and therefore not readily interpretable by the abovementioned analytical approaches, few studies in the analysis of electrochemical noise to date have exploited advances made in the analysis of nonlinear systems. In this paper, the use of phase space methods to analyze and detect change in corrosion systems via electrochemical noise is considered. In particular, the electrochemical noise data are used to reconstruct trajectories in the so-called phase space of the system and changes in the topology of these trajectories or attractors as represented by correlation dimension curves are consequently interpreted as an indication of change in the dynamics of the system.

Jan 1, 2005

By C. Scheffer

This paper describes a model that can simulate the behaviour of a pneumatic intensifier that is generally referred to as an ?air pump? (AP). The AP is used in many South African underground mines, and utilizes compressed air with pressures between 0.3?0.6 MPa to pump water up to pressures of 12?18 MPa. The high pressure water is used in numerous underground mines to pressurize props and roof bolts that act as safety and roof support devices. The simulation model reproduces the intensifier's operation under various conditions and therefore can be used to investigate the AP's sensitivity towards environmental conditions, design parameters (such as spring stiffness, plunger diameter, nozzle diameter etc.) and operating conditions. Model validation by comparison with laboratory experiments showed good correlation. The model can subsequently be used to investigate design changes aimed at improving the AP's performance and reliability over a wider range of operating conditions.

Jan 1, 2005