Search Documents

By E Villaescusa, C Drover

The stability of access tunnels is one of the main engineering challenges in deep underground mine construction. Many underground hard rock mining operations are now reaching depths where the induced stresses are such that sudden and violent failure of the excavations can occur very soon after construction. The loading conditions on the installed ground support schemes are often underestimated by conventional engineering design methods. Therefore, the actual loading conditions often exceed the installed ground support capacity. This can result in failure of the excavations and, in extreme cases, potentially closure of mining operations amounting to hundreds of millions of dollars in lost production. More frequently, violent excavation instability at great depth causes operational delays, costly and unplanned rehabilitation, as well as risks to worker safety. In order to address this challenge, this paper briefly summarises a modern, innovative approach to the design and construction of mine development at great depth. The process follows seven main steps. The first step is to characterise the rock mass strength, structure and stress. The second step is a stability assessment, which identifies the plausible modes of excavation failure, based on the rock mass characterisation. The third step is the definition of an excavation geometry which is harmonic to the high stress conditions. The fourth step is to prepare a site-specific face destressing drill and blast design which will reduce the potential for rock mass instability during the development construction cycle. The fifth step is to accurately quantify the expected loading conditions on the installed ground support. The method of doing so is uniquely analytical and probabilistic. It is based on the natural mechanical relationships between rock strength, structure, induced stress and the physical characteristics of the instability, including its mass and ejection velocity. The sixth step of the design process is to specify a ground support scheme arrangement with sufficient strength and displacement capacity to exceed the rock mass demand by a safe margin. The final stage is to install the complete ground support scheme using mechanised technologies which minimise the exposure of the equipment operators to unsupported ground at the tunnel face.

Nov 29, 2022

By E Kabwe, M Karakus

Deep hard rock underground mines tend to experience high stress as such drives exhibit dynamic responses attributed to a rock burst variant (strainburst). This dynamic behaviour is difficult to predict, and every effort is made to devise the appropriate dynamic support system for its associated failure restraint. This paper outlines the back analysis and the support scheme design for an underground decline that exhibited damage from a dynamic strainburst occurrence. It employs a decline section that experienced a dynamically loaded strainburst that initiated rock fragment ejections. The procedure involves a preliminary structural analysis, a seismic intensity measure, and a rock mass simulation to determine the static stress concentration and ground support system response. The numerical simulation is conducted in FLAC3D which employs the advanced strain-softening IMASS constitutive model governed by two Hoek–Brown (HB) bounding yield surfaces. To account for the post-peak brittleness response associated with strainburst the plastic strain multiplier () is adjusted to 0.0 < < 1.0. The back-analysis shows that the occurrence was initiated by a low-intensity seismic wave that superimposed an extra stress component to the initial static stress which triggered rock fragment ejections. Additionally, the appropriate support scheme comprised of Weldmesh, Fibrecrete, static (split set) and yieldable (Kinloc) reinforcements is recommended and implemented. Thereafter, the bolt’s efficiency is evaluated based on the axial force and elongation capacities and then compared with the published bolt performance data. The evaluation results show that the maximum bolt axial force (0.1 per cent) and elongation (0.006 per cent) are below the designed capacity and rupture strain.

Nov 29, 2022

By A Mortazavi, M Akhmedya

Mining is recognised as being one of the most dangerous industries in the world due to the difficult working conditions. Working in such hazardous circumstances in an underground mine often results in a variety of accidents. The working conditions at Kazakhstan’s underground mines have deteriorated owing to a lack of a risk-reduction plan and methodology. This paper evaluates different underground mines in Kazakhstan and demonstrates the employed mining method and the observed failure modes. Risk assessment has long been recognised as a valuable technique for preventing accidents. In the underground mining sector, risk assessment tools play an important role in avoiding work-related accidents. However, geotechnical uncertainty is a significant source of severe incidents like stress-induced roof collapse, wedge failure, seismicity etc, which result in human and financial losses. A geotechnical risk assessment performed early in the mine design process might assist justify a different mine design component, such as different support systems for a dangerous location within the mine openings during mining. The goal of this research is to create a damage/failure database aiming at the development of a geomechanical risk assessment methodology. This work identifies a thematic structure linked to risk assessment and management for the examined Kazakhstan mining sector. As part of the developed database, the dominant modes of failure within the Kazakhstan underground mining conditions were investigated. The study will provide opportunities to establish future research objectives for Kazakhstan’s mining industry where there are significant gaps between state-of-the-art research and mining operations in practice.

Nov 29, 2022

By B Vorster, T Medhurst, A Huey

Roof conditions at Oaky North Mine can be prone to stress related damage and/or time dependent degradation. The ability to identify these areas prior to mining has proved challenging using traditional methods. To help alleviate this situation, a study was initiated to investigate methods for roof characterisation using geophysical logs. This involved the use of neutron log data to provide an indirect measure of the proportion of carbonaceous/micaceous laminae present in the immediate roof strata. Detailed analysis of the shale–porosity inter-relationships arising from this analysis provided a means to estimate the proportion of laminations for a given roof interval. This paper outlines the process and how it was used to improve the current GSR modelling and hazard mapping process.

Nov 29, 2022

By C Zhang, G Si, J Oh, X Zhu

The presence of rock joints has a huge impact on the strength, deformability, and permeability of fractured rock masses by providing surfaces of weakness on which further deformation are more prone to occur, and by serving as the major channels of water flow due to low matrix permeability. In earlier studies, water flow-through rock joints is often assumed as laminar flow between two ideal smooth parallel plates, and the well-known cubic law was derived and widely used to characterise the hydraulic behaviour of rock joints. However, natural rock fractures are irregular and of spatially varied aperture. Thus, the concept of equivalent hydraulic aperture was introduced to modify the cubic law. Numerous works have been conducted on the relation between hydraulic aperture and mechanical aperture incorporating various geometrical parameters. The surface roughness is one of the most sensitive factors for water flow-through rock joints. The aperture distributions are irregular in natural roughed fractures relative to the parallel plates. Barton et al (1985) and Olsson and Barton (2001) incorporated the joint roughness coefficient JRC in evaluating hydraulic aperture and proposed an empirical equation based on fluid flow tests. However, their equations do not conform to the dimensional consistency. Many other researchers (Zimmerman and Bodvarsson, 1996; Xiong et al, 2011; Li et al, 2019) considered aperture distributions in their equations. But the aperture distributions change during shear was always neglected. The contact of rock joints also has a significant impact on the hydro-mechanical behaviour of rock joint, since fluid tends to flow-through a rough joint along connected channels while bypassing the contact obstacles with tortuosity. Nonetheless, previous research mostly considered joint roughness or aperture changes based on 2D joint profiles, while the contact and tortuosity based on 3D surfaces were often overlooked. Only a few works have been made on quantifying the effect of contact area on flow behaviour (Walsh, 1981; Zimmerman et al, 1992; Zimmerman and Bodvarsson, 1996; Yeo, 2001), and mostly ignored contact area change induced by shearing and the associated impact on flow behaviour. Summarily, the quantification of fracture geometry effects on water flow in single rock joints still needs further investigation, especially when considering coupled shear-flow processes. This paper, therefore, aims to study the impacts of contact area and aperture distributions of the single rock joint on the flow behaviour. The evolutions of contact area and aperture distributions induced by shear are considered. Then, an improved model for estimating the hydraulic aperture with the mechanical aperture incorporating the above factors is developed. Finally, a series of shear and shear-flow tests are conducted on artificial joint samples and the model performance is verified by comparing against the results of experimental tests.

Nov 29, 2022

By T M. Nester, D J. Reardon, A N. Page, B J. Barsanti

The load capacity of a friction bolt has long been regarded as 4 t/m of embedment for ground support design analysis and supported by in situ pull test results. In recent years, the authors have observed lower pull test results or inconsistent results which were rarely sighted in the early 2000s. The lower pull test results indicated in some cases that reliable friction bolt capacity (≥90 per cent of results) is closer to 3 t/m of embedment with some geotechnical engineers adjusting the ground support parameters in the design work accordingly. This can be in contrast with other mines which reliably obtain 4 t/m (or greater) using the same suppliers bolt in similar ground conditions. This raised several questions: • What is the effect of poor installation (bolt twist or bolt hole deviation)? • Does the performance of friction bolts vary in different rock masses? • Does bolt performance vary between suppliers? • What effect does increased jumbo feed/percussion/rotation settings have? • Have the bolt dimensions or steel strip width changed? • Have the physical bolt properties changed? • Have the steel properties changed? This paper was aimed to answer as many of these questions as possible and discuss each variable in detail. This project included friction bolt trials at various mine sites across Australia, multiple friction bolt manufacturers, steel manufacturers and laboratory analysis. The paper also includes discussion on what the authors consider best practice for pull testing. It should be noted, the terms ‘friction stabiliser’ and ‘split set’ used in this paper are used in a generic manner and is not linked to any specific ground support supplier. Whilst its acknowledged within the industry the term split set and friction stabiliser is used interchangeably, the authors acknowledge that the term split set is a trademark of Split Set Mining Systems and has been used in context in this paper.

Nov 29, 2022

By R deMoraes, A Bobet

The last decade has seen a resurgence of interest in lunar exploration and the emergence of countries like China and India as space fairing nations. In 2004, the US announced a new Vision for Space Exploration, whose objectives focused on human missions to the Moon and then Mars. The near future is likely to see the emergence of a worldwide drive to revisit the Moon as the first step in investigating the Solar System. To date, the Apollo missions provide our only experience of human operations on the Moon or anywhere else beyond Low Earth Orbit. Much was learned from these missions. However, their short duration means that many of the environmental effects that will be important for longer-duration missions could not be quantified. In addition, long-duration missions and infrastructure on the Moon require new technologies and capabilities, which must operate successfully and reliably in this lunar environment. Developing these technologies poses significant challenges for the exploration program. The paper discusses the risks associated with the construction of lunar surface and underground structures and the challenges to adopting the standards and rock mass classification systems developed on Earth and their applicability to the Moon. Moreover, an exchange of views to explore near-surface geologic and geotechnical profiles of the Moon is emphasized and implications of the lack of knowledge on rock mass characterisation of the Moonrock mass, the lack of theoretical/empirical experience on the use of rock mass systems outside Earth, and uncertainties.

Nov 29, 2022

By I Canbulat, G Si, Y Duan, X Luo

The presence of unfavourable geological structures such as faults and dykes often can contribute to coal burst risk. Seismic events associated with rock fractures tend to cluster around these structures and it is important to understand the characteristics of seismicity for coal burst risk management. In an Australian underground longwall coalmine, two clusters of seismic activities close to the longwall face and within a section of the maingate roadway which was intersected by a major dyke were respectively identified. The induced seismicity in the dyke-roadway area was closely related to the longwall mining. These seismic events were located and the distribution of seismic events shows that more fractures were distributed on the inbye side of the dyke. The spatial-temporal changes of the seismic event locations delineate the fracture propagation as the longwall mined through the dyke. The frequency-magnitude relationship of seismicity was analysed and it was found that it changed significantly when the longwall was mining towards, through and past the dyke. The monitoring results demonstrate that because of the stiff dyke, the seismicity was intensified in the roadway section. It proves that the dyke promoted stress re-distribution and seismicity in its vicinity. More fractures were induced in the hanging wall of the dyke, whereas less strain energy was accumulated and released in the footwall of the dyke.

Nov 29, 2022

By K Young, M Martin, D Payne

This paper outlines the evolution of managing high consequence risk scenarios in BHP Coal, with particular focus on managing the stability of an endwall that is adjacent to a public infrastructure corridor running through a Central Queensland coalmine. BHP Coal developed a Geotechnical Consequence Register after industry failures identified shortcomings in traditional risk assessment practices. Traditional risk assessments consider the consequence and likelihood of a geotechnical event occurring under normal operational conditions. As such, the risk rating for a high consequence, low likelihood failure may fall within the acceptable range, even where a lack of meaningful geological data exists due to the area being off lease or outside of mining reserves. The Geotechnical Consequence Register lists all geotechnical failure scenarios of high consequence, identifies if current controls are adequate, and highlights if specific Geotechnical Management Plans are required. This case study reviews a failure scenario that was identified through the geotechnical consequence register. The scenario had previously been considered low likelihood and subsequently driving a low risk; however, the likelihood ranking was impacted by a lack of geological data outside of the mining lease and predominately informed by an acceptable historical slope behaviour. Additional exploration identified previously unmapped faulting which increased the risk rating. The requirement to develop a specific management plan resulted in an increase in the required factor of safety, design changes, the implementation of additional monitoring and a corresponding monitoring Trigger Action Response Plans (TARP). In the case study area, the initiation of a geotechnical instability was identified early through the increased monitoring program. The instability was successfully managed and any impact to the infrastructure corridor off lease was prevented. BHP Coal has used the Geotechnical Consequence Register for several years to identify and assess high consequence geotechnical failure scenarios. In some areas this has justified additional exploration, more stringent design acceptance criteria and an increased level of geotechnical monitoring. The process has been successful in ensuring that geotechnical risk is controlled in areas that often receive less attention than active production areas.

Nov 29, 2022

By J Player, G Sweby, S Webber, E Jones

Seismic systems are a tool for the monitoring and forecasting the rock mass response to excavation. Common issues encountered at mine site audits and reviews are: how to design an effective seismic system, implementation of the design, interpretation of seismic source results and understanding the reliability of the seismic source. These issues are often a function of several items including: • Experience of site personnel in undertaking seismic system design. • Personnel not envisioning multiple phases of system expansion to understand system robustness issues. • System design/expansion occurring in response to damaging seismic activity rather than planned expansion of a system • The mine access development is often localised in comparison to the total orebody being mined hence, planning sensors in longholes in advance of development rather than in short holes close to development will improve the three-dimensional aspect of the network. • Limited site processing of the seismic event data, hence engineers do not see the uncertainty associated with event location, size, source and system layout. Mine site users require a framework to appreciate the challenges and limitations in locating large events. For example, event locations are given as precise measurements (to the nearest centimetre) whereas the volume of deformation resulting in the event often has dimensions of tens of metres or more (as defined by the source radius). A stronger awareness of the uncertainty of rock mass yield within large seismic sources will assist site users in the interpretation of rock mass damage. The encountered design and implementation errors are reviewed and discussed with a practical set of rules presented to provide a robust seismic system that provides consistent results and increases the user’s understanding of uncertainty in source location and size. The authors’ experience across multiple mine sites, seismic systems and damaging seismic events over a 30 year period has been summarised into practical rules for site personnel of all experience levels.

Nov 29, 2022

By E Villaescusa, C Drover, I Onederra

Development face destress blasting is a construction technique in deep mining, which aims to prevent, reduce the frequency, or manipulate the timing of violent, stress-driven rock mass instability at the face. This paper presents a destress blasting design concept that was optimised for the specific rock mass conditions of a deep mine using the Hybrid Stress Blasting Model (HSBM) software. The design was then implemented in an area of the mine where stress-driven instability of the face regularly occurred during development. An adjacent tunnel was constructed in parallel without destressing, within the same rock mass conditions, as a control. The rock mass response to each excavation was quantitatively compared using high-resolution local seismic monitoring. Visual observations of the fractures created by destress blasting were also made. The analysis indicated that destressing reduced both seismicity and the rock mass stiffness ahead of the face. This was inferred from the spatial broadening of the development seismogenic zone and the typically significant reduction in the spatial density of seismic events. Seismic source mechanism analysis also indicated that destress blasting generated a much wider variety of failure modes than conventional blasting. Most seismic source mechanisms following destressing were associated with natural joint structures. A relatively small portion were consistent with newly created blast-induced fractures. The greater diversity of rock mass failure modes associated with destressing implied a lower potential for stain-energy accumulation within the rock mass at the face, and thus a lower risk of hazardous instability. Observations of visible rock fracturing indicated that the major principal stress influenced the damage intensity on natural geological structures within the destressed zone, and that numerical predictions of radial fracturing limits made by HSBM analysis were realistic representations of the real blasting performance.

Nov 29, 2022

By P Khalkho, M Singh

Rock masses when subjected to uniaxial or triaxial cyclic loading (eg in hydraulic running tunnels, during retrieval and injection of oil and gas from storage underground caverns and haulage roads), the material has a tendency to fail in fatigue. In order to design safe and reliable underground structures, the determination of brittleness under such loading conditions becomes a pre-requisite. Brittleness influences strongly the failure process and makes the rock mass behaviour complex under different tunnelling and mining activities. Brittleness Index is a term to quantify the brittleness feature of a specimen. In the present study, an attempt has been made to quantify the brittleness of jointed specimens using different brittleness criteria. The joints of the model jointed specimens were oriented at an angle of θ=15° normal to the loading direction, each having three different JRC’s=2–4, 12–14 and 14–16. The specimens were tested under triaxial conditions in incremental complete cyclic test scheme performed at displacement-controlled mode. Different brittleness criteria were used ie stress-strain dependent brittleness index, Young Modulus approach and energy-balance based mechanism. It was observed that energy-balance based mechanism which consider the post failure behaviour is more descriptive to reflect the whole variation of brittleness from sheer brittleness to ductility.

Nov 29, 2022

By J Player, P Mikula, G Sweby

A numerical modelling back-analysis exercise was carried out at a WA gold mine at which early signs of seismicity (rock noise, scatts from active faces) were becoming apparent as depth of mining increased towards the 500 m mark. Some strain bursting had occurred and it was necessary to discover what the implications of this were for greater depth. The aim of the modelling was to: 1. Establish a correlation between observed ground conditions and model predicted damage, in overstressed areas of the mine. 2. Use this correlation to forecast rock mass damage and ground control requirements for proposed future stoping panels at greater depth. Good correlation has been achieved between observed rock mass damage, and a 3D Finite-Element RS3 model, run in elastic mode. Two candidate stress field orientations were modelled. The model parameter best fitting the observations was the Strength Factor (SF), the ratio of strength/stress. The good match (correlation coefficient of 0.7) between observed and modelled suggests that the elastic approach is justified for the depth range and rock mass properties analysed. The correlation also enabled a link between observed damage and installed ground support performance. Using the linear best-fit between observed and modelled, a forecasting exercise was carried out using the same RS3 model, modified to include future stoping. The resulting damage and ground support categories were obtained from the modelled SF for each proposed stoping level. Also, a series of generic geometries was assessed to investigate the impact of varying stope face lead/lag distance, sill pillar height and stope pillar size, on ground conditions. The key finding of the generic geometries were: • Ground support schemes have been defined for the expected conditions. • All ore drives are expected to have significant damage in the backs and rehabilitation. • Lead/lag distance not to exceed 10 m. • Sill pillar/level intervals of less than 20 m require an increase in ground support scheme. • Pillar sizes for maintaining footwall and hanging wall stability should be at least 10 m × 5 m.

Nov 29, 2022

By B Darlington, L Sandberg, O Vallati

The D47 and D39 Mechanical Dynamic Extra bolts (D47 MDX and D39 MDX) have been developed in response to the ever-increasing demand from the mining industry for rock bolts with high dynamic capacity. To prove such capacity, Sandvik has performed numerous in situ dynamic testing with the unique Dynamic Test Rig (DTR) (Darlington, Rataj and Roach, 2019; Roach, Rataj and Darlington, 2019). To complement the collection of testing data, Sandvik, in collaboration with the Swedish Research Institute for Mining, Metallurgy and Materials (Swerim) have performed additional experiments in laboratory condition using Swerim’s new drop test rig. This rig utilises a momentum transfer method to apply a dynamic load to the bolt. The sample falls together with the mass until the support beam impacts stationary dampers and the momentum energy is transferred to the bolt. Part of the charged energy is released by the dumpers while the remaining portion is absorbed by plastic deformation and/or displacement of the ground support element. The D47 and D39 MDX bolts have been tested at Swerim’s test facility with different levels of input energy. Six tests were performed at the specification energy of 36 kJ and six tests were carried out with the maximum allowable energy from the facility, ie 44 kJ. The bolts confirmed their dynamic performance absorbing the input energy without failure. The D47 MDX bolt absorbed up to 33 kJ with 150 mm displacement while the D39 MDX bolt absorbed up to 35 kJ with 162 mm displacement. This work will present an overview of the drop test rig at Swerim’s facility and a collection of results of the test performed on the D47 and D39 MDX bolts. The test method and results will be analysed and compared to the tests carried out with the in situ DTR.

Nov 29, 2022

By A D. Campbell

Sublevel caving (SLC) is a mining method adopted in a wide range of mining depths and ground conditions with various layouts adopted to suit orebody geometry. Sublevel caving offers more flexibility and versatility compared to other cave mining methods and is a low cost alternative to open stoping. SLC also has the advantage that stopes are not required to remain stable during production, and no backfill is required. This flexibility combined with increasing pressure on mines to target deeper and lower grade mineralisation has led to increased uptake of the method. The implementation of SLC mining methods across a wide range of mining depths and rock mass conditions has led to ground control practices which vary globally from mine to mine. To date, there has been limited documentation of ground control practices in SLC mining and few benchmarks available in the literature. This paper describes the main findings from a global benchmark of sublevel cave mines conducted over three years as part of the Caving 2040 research consortium. The purpose of the project was to document and compare operational practices, technical aspects and hazard management techniques across SLC mines around the world. The review included 21 mines spread over four continents and 17 different mining companies. This paper provides an overview of geotechnical conditions, challenges and ground control practices at each of the benchmarked SLC mines. Mine design and sequencing practices adopted for ground control purposes and hazard mitigation are provided with case studies. The impact of depth and rock mass conditions on mining productivity and development rates is also described.

Nov 29, 2022

By A Jafari, N Khalili, M Vahab, P Broumand

This paper presents the implementation of the eXtended Finite Element Method (XFEM) in the general-purpose commercial software package COMSOL Multiphysics for multi-field thermo-hydromechanical problems in discontinuous porous media. To this end, an exclusive enrichment strategy is proposed in compliance with the COMSOL modelling structure. COMSOL modules and physics interfaces are adopted to take account of the relevant physical processes involved in thermo-hydromechanical coupling analysis, namely: the mechanical deformation, fluid flow in porous media and heat transfer. The model preprocessing, level-set-updates, coupling of the relevant physics and postprocessing procedures are performed adopting a coherent utilisation of the COMSOL’s built-in features along with the COMSOL’s LiveLink for MATLAB functions. The capabilities and performance of the proposed approach are investigated by examining several multi-field thermo-hydro-mechanical simulations with reference to the block caving process in mines.

Nov 29, 2022

By K Li, C Zhang, i, J Oh, S Saydam, H L. Ram

Rock surface roughness plays an important role in excavation engineering projects and applications related to surface support structures, such as shotcrete and thin-sprayed liner (TSL). The morphology of the substrate affects the mechanical behaviour at the interface significantly. Therefore, it is necessary to quantify the roughness to investigate the relationship between roughness and mechanical properties. The joint roughness coefficient (JRC) proposed by Barton and Choubey (1977) is widely used in practice. It initially estimated the roughness by comparing it to 10 standard profiles visually. However, this method has lots of limitations, it is not only subjective but also a two-dimensional parameter with a small lab scale (Beer, 2002). The subsequent research on JRC, from visual comparison with Barton’s standard profiles to measuring the roughness with a profilometer (Weissbach, 1978; Alameda-Hernández et al, 2014). Then, 2D profiles or 3D surfaces by different technologies with higher resolution and accuracy, such as 3D laser or optical scanners (Fardin, 2004; Jiang, 2020, 2021). These 3D scanners are expensive and only suitable for laboratory scales. LiDAR scanners (Lato, 2009; Aubertin, 2022) have been applied in industrial size, but it is difficult to achieve a millimetre-level accuracy, which is mostly used to detect the thickness of shotcrete in practice. Thus, finding a cost-effective surface roughness measurement method with high accuracy is necessary. Photogrammetry is another method to digitalise the roughness of the surface. Similar to 3D scanners, photogrammetry also generates the point cloud of the objective surface and then reconstructs the 3D model of the objects. 3D reconstruction technology is a trendy technology in recent years. The structure from motion (SfM) algorithm (Westoby, 2012) to rebuild the 3D model with a flexible workflow, aligning photos, building dense point cloud, mesh and texture, which has been proved that can rebuild an accurate model in variable fields.

Nov 29, 2022

By M Khanal, J Qin, B Shen, Y Duan, X Luo

Gaining confidence in interpreting rock and strata properties of the coalmine roof is necessary for design, maintenance, modelling and optimisation of roadways supports. One of the key causes of roadway instabilities experienced in underground coalmines is an extreme variable nature (thickness, competence, discontinuities etc) of the coalmine roof. Normally, the thickness and strength of the roof are characterised with the geotechnical and geological data gathered from exploration boreholes, which are drilled often at considerable distances apart. This limited data cannot capture localised geological variations in the coalmine roof. With this background, this paper explores feasibility of using measurement while drilling concept to perform geotechnical characterisation of the coalmine roof. The parameters, for example, penetration rate, rotary speed, torque, sound, vibration, obtained during the drilling process can provide valuable insights into geotechnical properties. The paper describes the progress of the experimental work conducted at the laboratory on synthesized concrete samples representing various rock strata using a field-scale drilling machine. The samples with and without interfaces have been tested to replicate various underground roof strata. The signals returned from the drill machine, as the drill bit passes through the layers, have been analysed and interpreted to characterise whether the drill response data can differentiate various strengths associated with the rock layers. The initial laboratory results are promising as they show distinct responses of the various sample blocks in a controlled environment. The drilling data can differentiate the synthesized rock samples and detect ‘signatures’ of the roof strength variability and delineation of lithological interfaces (transitions). The weight and torque on the bit vary and show dependency on the strength of the blocks.

Nov 29, 2022

By T Wang, D Wang

Photogrammetry-based techniques supported by traditional mapping tools are more frequently used for open pit geotechnical mapping. It fundamentally involves the collection of geological, structural and rock mass data from pit batters when safe to do so. These are essential components for refining and implementing continuous improvements to geotechnical models. The geotechnical model is used to review bench performance, optimise geotechnical design parameters, interpretation and analysis of pit slope stability. This paper is a case study of implementing different pit mapping methods at Mount Carlton gold mine, North Queensland. It critically reviews the tools required, including the Brunton compass, mobile application Clino, geotechnical data mapping software CloudCompare (2015) and Sirovision software. The review compares the image precision, structural measurements and data analysis. The review also underlines mine site management philosophy for safe geotechnical data collection to identify in-pit geotechnical hazards and the mitigation of potential slope instability. Sirovision is a remote sensing system for site geology mapping and interpreting geotechnical characteristics of exposed mining faces. The system utilises off-the-shelf digital SLR cameras to capture stereo photographs of the rock face and uses the latest image processing technology to generate accurate 3D models. These 3D models are digitally analysed using computational geometry to extract unbiased and accurate geological and geotechnical data. CloudCompare processes high accuracy 3D dense cloud rock surfaces reconstructed with photogrammetry software to extract the geological planes using the FACET or Compass plugins. The major discontinuity sets can be observed and the orientation (dip/dip direction) obtained from the algorithm is accurate and reliable for geotechnical assessment, including kinematic and rock slope stability analysis.

Nov 29, 2022

By E Shilov, R Dixon, L Tovey

BHP Western Australian Iron Ore (WAIO) operations use a suite of slope monitoring systems which are deployed to operational areas based on the ground control risk. Slope Radars are one system used within WAIO, having recently deployed and integrated a network of 22 radar systems across the operations. The integration required the development of supporting network architecture, infrastructure, virtualised hosting, security protocols and a technology support model. This has enabled data transfer between the physical radar systems located in open pits, to on-site offices, a vendor supported remote control room in Indonesia and the WAIO Integrated Remote Operations Centre for data analysis and monitoring of system and displacement alarms 24/7. The typical technical skillset of a Geotechnical Engineer does not include the knowledge and capability to understand and develop the supporting IT infrastructure required for establishing an integrated radar monitoring network. This paper will provide a discussion of the technology considerations for integrating radar systems and highlight the importance of the developed partnerships between internal geotechnical and technology teams and the external vendor team to ensure a reliable, robust and scalable slope monitoring solution.

Nov 29, 2022