Search Documents

By Staff

A major emphasis of the U.S. Bureau of Mines is to perform research on the prevention of fatal accidents at mining operations. The leading cause of fatalities in the underground coal mining industry is groundfalls. This proceedings volume presents several new developments that are helping to prevent fatalities and reduce injuries by groundfalls. The papers focus on the problem from two different perspectives. About half of the papers present information and techniques that can be used to train and motivate miners to protect themselves from groundfalls. The other papers explain how to identify and respond to various geologic conditions that affect the stability of the mine roof. Of the 95 groundfall fatalities that occurred during 1986-90, 75% took place in Kentucky, West Virginia, and Virginia. The rate of groundfall fatalities was much higher at small mines. During 1986-90, the rate of groundfall fatalities at mines employing fewer than 20 people was 4.3 times higher than the rate for larger mines. Because so many groundfall fatalities are occurring at relatively small mines in the southern Appalachian coalfields, many of the papers focus specifically on the needs of this category of mine operations.

Jan 1, 1992

By Michel C. Frippel

This section of the Minerals Yearbook reviews the minerals industries of 29 countries: the 12 nations of the European Community (Belgium, France, the Federal Republic of Germany (FRG), Italy, Greece, the Netherlands, Denmark/Greenland, Spain, Portugal, Luxembourg, the United Kingdom, and Ireland); 6 of the 7 nations of the European Free Trade Association (Sweden, Nor-way, Finland, Iceland, Austria, and Switzerland); Malta; the 8 Centrally Planned Economies of Eastern Europe (the German Democratic Republic (GDR), Poland, Yugoslavia, Albania, Hungary, Czechoslovakia, Romania, and Bulgaria); and the U.S.S.R. Western Europe Western Europe [loosely defined to include the 12 nations of the European Com-munity (EC) and the 7 nations of the European Free Trade Association (EFTA)] is the single largest trading area and consumer of raw materials in the world. If Western Europe was at one time an important mining sector, it has now increasingly relegated the role of supplying minerals for its minerals processing industry to its ex-colonies in North and South America, Africa, and Australia. In this regard, Western Europe is the most important determinant of raw materials consumption (and thus raw materials production). There is an important reason for this since Western Europe lies somewhere between Japan at one extreme and the United States and the U.S.S.R. at the other extreme as regards the availability of natural resources.

Jan 1, 1992

By Harry E. Brownlow

The United States Bureau of Mines contracted Norecol to prepare a report identifying the regulatory processes associated with metal mine development in British Columbia using the Snip Mine as a case study. The intent of this study is to assist industry and regulatory agencies in developing understanding as to differences in objectives, perspectives and operating methods. The case study will be incorporated into a larger report summarizing the comparative advantages and disadvantages of metal mine permitting in British Columbia and Alaska. The purpose of the report is to identify the development schedule and permitting process at Snip which will assist the U.S. Bureau of Mines in suggesting improvements in environmental review and permitting processes for mine developments. The report provides an abstract of the environmental assessment review processes in Canada and the Mine Development Review Process in British Columbia and provides an understanding of the linkages between policy, legislation, and environmental review.

Jan 1, 1992

By Guo Junfeng

The strength of coal mass saturated with gas is an essential parameter in studying the mechanism of gas and coal outburst, and its prediction method. Up to now, there has not been a method for determining the strength of coal mass saturated with gas. This paper describes a new method whereby the strength of in-situ coal mass can be determined and stored continuously and automatically. The simulation results obtained in the laboratory indicate that the new method allows a fast, reliable, inexpensive and convenient determination of the strength of coal mass.

Jan 1, 1992

By I. L. Follington

A breaker line support (BLS) monitoring system, BLSmon, has been designed and constructed by the CSIRO and installed and commissioned at Laleham No.1 Colliery, Queensland. This system was designed to record hydraulic leg pressure and canopy position measurements and relay these, in real time, to the surface. The system has shown itself to be capable of operating on the BLSs without any adverse affect on production, Analysis of the results of the monitoring exercise has shown that rate of change of leg pressures on the BLSs could be used as an aid in the prediction of adverse mining conditions. Under favourable mining conditions the supports were observed to initially unload from the set pressure, this unloading reduced with time and by the end of a typical lift cycle had either ceased or reversed slightly. This behaviour was considered to be due to one of four possible causes, these being; the compaction of floor debris, and/or compaction of the floor, and/or crushing of the roof and /or support creep. The actual cause can only be determined through detailed monitoring of both roof and support convergence. However observational data would suggest that compaction of debris and softened floor material beneath the supports was the most likely cause. The few positive loading rates recorded under these conditions were of short duration and occurred towards the end of individual lifts. Where mining conditions were unfavourable the negative rates of change of pressure, unloading of the support, were reduced throughout a lift, in both duration and magnitude, when compared with favourable mining conditions. Over the same period the positive rates of change were observed to be greater. The rate of change of loading and convergence can be utilised to identify the onset of instability in the lift area. However, before this facility can be utilised by the mine for the reliable prediction of instability more monitored data and sophisticated processing techniques are required. A mechanism has been postulated for the deformation behaviour of the roof and pillars in a mechanised pillar extraction operation from the continuously monitored data, observational data and results of previous studies. The 7 m wide fenders were observed to yield under abutment stresses before lifting commenced. The stability of these fenders throughout the lifting sequence was considered to be dependant upon the magnitude of their post peak load carrying capability. This is influenced by the post peak stiffness and the extent of roof lowering in the vicinity of the fender. Difficulties with fender extraction occurred where remnant coal left standing in the goaf caused uncaved goat to bridge to the mined fender. Difficulties were also experienced where sub-vertical jointing occurred in the roof of the split reducing it's ability to bridge effectively. Despite the relatively short monitoring period, the potential role and application of continuous monitoring in advancing understanding of the rock mass response to mechanised pillar extraction operations has been demonstrated. This understanding now requires enhancement and shows great potential for aiding the optimisation of mechanised pillar extraction operations.

Jan 1, 1992

By M. Polat

A combined heavy medium-flotation process which incorporates the advantages of two widely employed cleaning methods, namely, heavy medium separation and flotation was used to achieve improved separation of coal from ash at fine sizes and to recover the heavy medium as a substantially recyclable product. The investigation was carried out in two successive phases. In the first phase, tests were performed to deter-mine the effect of different variables such as the medium density, flotation time, magnetite type, etc. on the efficiency of the process using in-plant samples from Homer City Coal Preparation Plant. In the second phase, the optimum conditions determined in the first phase were employed to determine the applicability of the process to a few Central Pennsylvania coals. It was observed that the process was very effective in recovering the magnetite. In most of the cases investigated, the magnetite was separated from the non-magnetic material at approximate-1 to 99 % recovery with a grade ranging from 95 to 99 %. The grade of magnetite decreased with increase in ash content of coal and with decrease in size of magnetite.

Jan 1, 1992

By Gary K. Elliott

Many industrial processes generate hot waste gases which contain particulate pollutants. Conventional clean-up techniques suffer limitations either because collection efficiency is low or because the gas must be cooled before treatment. thereby increasing costs and preventing energy recovery. The application of increasingly stringent environmental legislation to the non- ferrous metallurgical industry Is presently illustrating these conventional technology limitations. Low density ceramic media allow filtration to take place at high temperatures and are now rapidly becoming accepted in many industries. This paper reviews experiences with a proprietary low density ceramic filter element, Cerafill. It includes consideration of the structure, composition. typical operating and case studies with particular reference to non-ferrous metallurgical furnace applications.

Jan 1, 1992

By William J. McDonough

Advanced materials are polymers, metals, and ceramics fabricated as intermaterial compounds, alloys, or composites. The resultant components have higher strength-to-density ratios, greater hardness and wear resistance, and one or more superior thermal, electrical, or optical properties when compared with traditional materials. Advanced materials, the basis for many of today's emerging technologies, offer savings in total energy consumption, improved performance at reasonable cost, and less dependence on imports of strategic and critical mineral resources.

Jan 1, 1992

By Medhurst TP, Trueman R, Hutchinson IN

A breaker line support (BLS) monitoring system, BLSmon, has been designed and constructed by the CSIRO and installed and commissioned at Laleham No.] Colliery, Queensland. This system was designed to record hydraulic leg pressure and canopy position measurements and relay these, in real time, to the surface. The system has shown itself to be capable of operating on the BLSs without any adverse affect on production. Analysis of the results of the monitoring exercise has shown that rate of change of leg pressures on the BLSs could be used as an aid in the prediction of adverse mining conditions. Under favourable mining conditions the supports were observed to initially unload from the set pressure, this unloading reduced with time and by the end of a typical lift cycle had either ceased or reversed slightly. This behaviour was considered to be due to one of four possible causes, these being; the compaction of floor debris, and/or compaction of the floor, and/or crushing of the roof and /or support creep. The actual cause can only be determined through detailed monitoring of both roof and support convergence. However observational data would suggest that compaction of debris and softened floor material beneath the supports was the most likely cause. The few positive loading rates recorded under these conditions were of short duration and occurred towards the end of individual lifts. Where mining conditions were unfavourable the negative rates of change of pressure, unloading of the support, were reduced throughout a lift, in both duration and magnitude, when compared with favourable mining conditions. Over the same period the positive rates of change were observed to be greater. The rate of change of loading and convergence can be utilised to identify the onset of instability in the lift area. However, before this facility can be utilised by the mine for the reliable prediction of instability more monitored data and sophisticated processing techniques are required.

Jan 1, 1992

By James Y. Oldshue, Paul M. Kubera

Ore processing requirements in the gold industry are similar to those in other sectors of the minerals industry. In all cases, the processes revolve around the handling of large volumes of ore slurry, incorporating either physical processing or chemical processing steps which are related to distinct mixing application classes as defined in Table 1. From this standpoint, the complexity of the applications range from the simple (blending, solid suspension, etc.) to the complex (e.g., multi-phase reactor systems). The large volume of material to be processed dictates the large equipment size which is characteristic of this industry, and the often remote locations place a premium on both mechanical and process reliability.

Jan 1, 1992

By W. Baguley

There are many carbon-in-pulp and resin-in-pulp screening devices which are at present in use in the South African mining industry. Each one of these screens has been an improvement, from the very basic air cleaned and 'EPAC' types which were either circumferential or · diametrical launder screens, which were developed for C I P in the early 1980's, through to the more sophisticated LAP and Kambalda Screens. Each one of these screens not only increased the performance or throughput per square metre than its predecessor, but also addressed maintenance problems, wear, reliability and the ability to handle surge conditions, thereby preventing tank overflow. However, very little theory has been presented concerning, the flow of pulp through internal screens, carbon loss and screen wear rates. Almost all this information is based on empirical data. The NKM screen continued this trend and was able to offer flow rates in excess of 180 cubic metres per square metre of screen per hour and an average screen life of approximately six months. However, with increasing sophistication of the screen and the use of wedge wire as opposed to the normal woven wire, the mass was significantly increased and costs began to mount. Therefore, Mixtec undertook to develop a radically different screen, which incorporated many of the advantages of .the existing equipment and combined a few of its own.

Jan 1, 1992

By D. E. Walsh

The behaviour of gold particles on a spiral was studied using radioactive gold tracers. The method allowed the effect of particle size, particle shape, pulp density, feed rate, and splitter settings to be studied. Although the method has been successfully applied to other gravity concentrators, it was found that reliable results were more difficult to obtain on the spiral. However, these preliminary results show that provided suitable precautions are taken, the technique is capable of providing valuable information that cannot be obtained by conventional studies, and could be used to better optimize spiral performance.

Jan 1, 1992

By V. Svalbonas

When the Trelleborg Divisions of Boliden Allis and MPSI merged, a unique opportunity occurred for two independent mill fabricators to compare various design procedures and the research upon which they were based. This paper documents such a comparison in the structural design area. Several SAG mill analyses are compared using both Boliden Allis and MPSI methods. The differences and similarities are then utilized in a correlation of critical stress definitions and the acceptable design and inspection criteria.

Jan 1, 1992

By Kenneth L. Driggs

The Environmental Protection Agency's Clean Air Act? of 1970 provided the driving force for the current Magma Smelter configuration. The historical and technical perspectives of those process developments are reviewed?. Innovations in procedures and equipment have allowed compliance with the requirements of the regulating authorities?. The wet scrubbing of converter gasses and the monitoring of converter operations by a controlling foreman are two of the major contributors? to these successes. The Clean Air Act Amendments of 1990 have posed many new concerns? for all U.S. industry, including the few (seven) primary copper smelters remaining. Future concerns include tightening the sulfur dioxide ambient ?Standard from the current three-hour averaging period to one hour.

Jan 1, 1992

By L. J. Friedman

Smelter operating and environmental requirements demand high on-stream time (high reliability) from the primary smelter sulfur retention device - the sulfuric ?acid plant. The key to reliable smelter sulfuric acid plant operation is the gas cooling and cleaning system. Problems in the gas cleaning system cause corrosion, plugging, equipment failure, etc - plant down time, in the contact section of the plant. The last fifteen years have seen major changes in gas cleaning system design _to the current standard of brick lined venturi scrubber, packed gas cooling tower with plate type liquor coolers and lead or plastic tube precipitators, The current? design offers improved' impurity scrubbing along with increased reliability. in addition, a number of alternate gas cleaning systems have been offered Chemetica LAB System; Monsanto DuPont D:Jna-Wave Syatem1 Lurgi venturi scrubber with lead star gas cooler. This paper will review the design and operating advantages, disadvantages, and risk of the standard gas cleaning system and compare it to the alternate systems. _

Jan 1, 1992

By A. M. Wala

It is common practice in Appalachia, when extending the life of an existing mine, to acquire the adjacent reserves and extend the existing mine into it. Also, often the existing mine is renovated to accommodate the new conditions. The existing mining system and the track and belt haulage systems may be modified while the new property is integrated into the old one. All of these changes create new constraints for the mine ventilation system (M.V.S.) that require proper planning and control procedures. The authors describe and present the study that was carried out for the ventilation system of a newly expanded underground coal mine located in the Appalachian coal region. Discussed first is the process of correcting the ventilation system of the existing mine. Then, some of the stages of controlling the expanded system are discussed. Finally, numerical data for these steps are presented.

Jan 1, 1992

This paper discusses equipment replacement strategies and specifically addresses the upgrading of technologically superseded equipment. The process of equipment replacement evaluations is reviewed, and areas have been highlighted where currently accepted practice results in a bias towards retaining existing equipment longer than otherwise justified. The Discounted Average Cost Method is described and the advantages of the technique for this style of decision making discussed. Several key issues influencing the replacement evaluation are also presented together with examples from recent consulting work.

Jan 1, 1992

By Milos J. Bila

I would like to discuss today several safety topics that we at Nobel feel are going to be particularly critical to all of us who are involved in the manufacturing, transportation, storage and use of commercial explosives during the '90s. My purpose is to identify these topics in order to allow those in the commercial explosives community to better understand the potential difficulties we face.

Jan 1, 1992

By Randall M. Wheeler

Pre-blast surveys are used to document the condition of a structure prior to the commencement of blasting activities. They provide the best means of determining the pre-existence of visible cracking and deterioration in a structure before blasting is initiated. A small investment in a good pre-blast survey, coupled with good public relations, could mean a large cost savings for a company in the future.

Jan 1, 1992

By R. J. St. Eloi

The Kidd Creek Copper Smelter has been expanded from its original design of 59,000 tonnes of copper per year to over 120,000 tonnes per year .. Modifications to the process gas handling system and acid plant have been made to accommodate this higher production rate and to .generally optimize the operation. The gas handling system associated with the continuous smelting process is discussed in terms of boiler accretions and modifications to minimize their impact on operations; design changes to effect reductions in high pressure drop duct configurations; material changes to overcome corrosion and plant additions to 'improve gas cleaning capability. The acid plant is reviewed with references to changes made to accommodate the increased S02 gas strength resulting from the higher smelting rates;

Jan 1, 1992