Search Documents

By Taghi Sherizadeh, Kutay E. Karadeniz, Dogukan Guner, Samuel Nowak

Underground mining environments bring occupational health and safety issues with some severe dangers such as mine disasters like explosions. During such events, miners might escape using main access openings, or find a safe haven like refuge alternatives (RAs) to wait and be rescued and evacuated to the surface. In this paper, RAs are explained with their early and current applications. A classification as permanent and portable is explained depending on the conditions and their abilities. This classification is followed by the utilization and survivability of RAs with the requirements and recommendations of the main mining countries. Based on the utilization and survivability constraints, basic human requirements, waiting for a rescue team, and the required physical specifications of RAs during the events are analyzed in detail for various countries with their regulations. Among these, the specification, resistance to the explosion, is discussed in particular, and the studies in the literature are examined in terms of structural deformation. The highest deformed zones, the beneficiation of reinforcing steel components such as stiffeners, and the simulation approaches are investigated through this review.

Sep 24, 2022

By Juan J. Monsalve, Mario Karfakis, AMAN SONI, Nino Ripepi, Jim Hazzard

Pillar collapses are events that due to their severe consequences can be classified as high risk. The design of pillars in underground room-and-pillar operations should migrate to risk-based design approaches. The authors of this work proposed a risk-based pillar design methodology that integrates stochastic discrete element modeling for pillar strength estimation, and stochastic finite volume modeling (FVM) for stress estimation. This paper focuses on the stochastic FVM component for stress estimation. The mining and geomechanical aspects of a case study mine (CSM) are described and pillar stresses are estimated by using three approaches: (1) analytical solutions, (2) 2D finite element modeling, and (3) 3D finite volume modeling. This operation extracts a 30° dipping deposit, which makes current underground stone mine design guidelines inapplicable for this CSM. This work compares results from each stress estimation approach and discusses uses the point estimate method as a simplified stochastic approach to evaluate the effect of rock mass elastic properties variability on pillar stress distribution. Results from this work show that the three estimation approaches lead to different estimations, possibly, due to the wide range of assumptions each estimation approach considers. It was also determined that the horizontal to vertical stress ratio has a significant impact on pillar stress magnitude. Therefore, it is recommended to perform in situ stress measurements, or assume worst-case-scenario values to account and reduce uncertainty due to this parameter. The stochastic stress estimation approach used in this paper provides results that can integrate a risk-based pillar design framework.

Sep 24, 2022

By Swades Kumar Chaulya, Vikash Kumar, Sushma Kumari, Naresh Kumar, Girendra Mohan Prasad, Monika Choudhary

During harsh weather conditions, the presence of fog, dust in the environment degrades the image’s quality, which affects the visibility of drivers of heavy earth-moving machinery in opencast mines. Due to low visibility, mining operations cannot be carried out as drivers are easily prone to accidents. This paper proposes a technique that includes developing a vision enhancement system called perceptive driving assistant system for increasing visibility of real-time video of the road in front of the vehicle for operators of heavy earth-moving machinery at opencast mines during harsh weather conditions to overcome the problem. The system consists of high-quality Internet Protocol cameras and thermal cameras for real-time image processing and other well-defined devices, which is quite capable of enhancing the visibility of the image, outlining edges of the road, and detecting obstacles present on the path of operators for smooth driving and reducing threat of accidents. A high-speed graphical processing unit has been used for quality-performance parallel computing, which is well suited for real-time operations to empower fast real-time operations. The calculated frame per second (fps) of image enhancement, object detection, and edge detection is 17.91, 15.91, and 25.09 fps, respectively. The actual frame rate is 26.07 fps, and after applying the algorithm, the final frame rate is 19.65 fps. The calculated accuracy of the object detection model is 81.23%. Field trials indicate that the developed system has performed adequately during foggy weather.

Sep 21, 2022

By Kristin K. Mueller, Lucie Coudert, Thi Yen Chau Nguyen, Lan Huong Tran, Jean‑François Blais, Guy Mercier

Fluorite (calcium fluoride—CaF2), also known as fluorspar, is an industrial mineral used in metallurgy, hydrofluoric acid production, and ceramics manufacturing. Based on the results from a previous study, a low-grade fluorspar by-product (20.0% CaF2) originating from the exploitation of a rare earth carbonatite deposit can be improved to 75.4% by combining magnetic separation and acid leaching. The present research aimed to develop and optimize a column flotation process to increase the purity of this fluorspar by-product by removing residual silicate minerals and meeting the requirements for ceramic manufacturing (> 85% CaF2). The optimal flotation conditions required for maximizing the recovery and improving the grade of a fluorspar by-product were identified using a conventional approach combined with a response surface methodology (Box-Behnken design). Optimal fluorspar flotation was achieved under the following conditions: 3.6 g/kg of sodium oleate as the collector, 2 g/kg of sodium silicate as the pH modifier and depressant, a conditioning time of 35 min, a flotation time of 7 min, and a solid-to-liquid ratio (S/L) of the pulp of 5%. Under these conditions, 86.8% fluorspar recovery was achieved, and the grade increased from 76.5% in the feed (metallurgical grade) to 88.6% (ceramic grade) in the final concentrate. The silicon content decreased from 5.66% in the feed to 1.12% in the fluorspar concentrate. Using magnetic separation before the flotation improves the final content of fluorspar in the concentrate with the final grade of 94.4%.

Sep 9, 2022

By Neel Gupta, Dustin M. Crandall, Brijes Mishra

X-ray computed tomography (CT) images of rock specimens often contain artifacts which must be corrected before scientific analyses are performed. This paper presents a new workflow of automated image processing to utilize poor-quality X-ray CT scan images. The workflow runs on the open-source image analysis software and efficiently separates desired features from low-contrast scanned images. The new workflow is a two-step technique using contrast enhancement and automated feature segmentation to generate noise-free binary images. The results of binary images using the proposed workflow and using a conventional thresholding technique are analyzed to show the quality of the proposed method. The paper also presents a workflow of estimating the structural geometries of features in two and three dimensions. The results of the structural feature analyses and computational time were compared between the open-source (ImageJ) and commercial image analysis software (Bruker Computed Tomography Analyzer). The commercial software was more computationally efficient, but the task-specific macros in open-source software enabled the user-desired automation in image processing and data extraction of desired structural features of comparable quality.

Sep 8, 2022

By M. Arlandi-Rodríguez, and A. García-Berrocal, A. Alonso-Jiménez, C. Lopez-Jimeno

Spain is a major producer of dimension stone, which is one of the most important industrial sectors in the northwest of Spain. This justifies the maintenance of these industries, although the technical and environmental requirements for their continuity are increasingly demanding. The main target of this paper is to present a new methodology in order to obtain k-ratio stress values on the basis of flat jack measurements and finite element numerical back- analysis with Rocscience© RS2 software. Continuous iterations were performed to try to find a relationship between the k₀ and the measured stress in the tunnel roof and sidewalls. It focuses on technical aspects of the method for designing mine chambers in the slate industry that were previously mined by open pit methods. The size of the chambers impacts the operating cost, and the dimensioning of a correct support ensures better efficiency and safety. Correct knowledge of the k₀ therefore is critical for the design of the support. The proposed new method entails a simplification of the classical procedure for estimating the k-ratio.

Sep 1, 2022

By D. F. Malan

This paper provides an overview of the concepts of citations and journal impact factors, and the implications of these metrics for the Journal of the Southern African Institute of Mining and Metallurgy (JSAIMM). Two key research literature databases publish journal impact factors; namely, Web of Science and Scopus. Different equations are used to calculate journal impact factors and care should be exercised when comparing different journals. The JSAIMM has a low impact factor compared with some of the more prestigious journals. It nevertheless compares well with journals serving other mining sectors, such as the Canadian CIM Journal. The problems associated with journal impact factors are discussed. These include questionable editorial practices, the negative impact of this concept on good research, and the problem of a few highly cited papers distorting the journal impact factor. As a consequence, there is growing resistance to the use of journal impact factors to measure research excellence. The San Francisco Declaration on Research Assessment is a global movement striving for an alternative assessment of research quality. As a recommendation, the Editorial Board of the JSAIMM should adopt a pragmatic approach and not alter good journal policies simply to increase the journal impact factor. The focus should remain on publishing excellent quality papers. Marketing of the Journal, the quality of the published papers, and its open access policy should be used to counter the perception that journals with high impact factors are better options in which to publish good research material.

Sep 1, 2022

By RavikiranVaidya, Vishal Dhamecha

Low Strain Pile Integrity Testing has been used in India since 1990’s and several have tried to demonstrate the utility and benefits of this method. However, use of this technology was limited till 1998 as not enough data maybe was not available to justify its use and application on major infrastructure and real estate projects. The first author has done significant work in this method resulting in its use in practically all sectors of the industry that use concrete bored pile foundations as a supporting element. The paper explains various signal enhancers or modifiers involved in processing of low strain test data and its implication on the final output. It also describes how the method can lead to abuse or can provide poor interpretation if incorrectly used. The current effort is to demonstrate that data collection and evaluation becomes complex with changes in soil stratum and pile profile. The paper highlights the present testing practices and provides a guideline for classification of pile integrity into few simple categories in Indian context rather than writing complex interpretations.

Sep 1, 2022

By Sunil S. Basarkar, Vinothkumar S

Ground Improvement Techniques serves to improve various engineering properties for supporting various foundations. These may be undertaken either by conventional or advanced methods. The Controlled Modulus Column (CMC), also known as Rigid Inclusion is a soil improvement technique to reduce the total and differential settlement by using semi-rigid soil reinforcement columns. The CMC technique can be executed by displacement or non-displacement methods. It does not aim to bypass the compressive layer or to install a pile that will directly support the entire load from the structure. Principle of the technique is to introduce a load transfer platform between the head of the column and structure and transform a uniform load into soil. Initially, the structural load transmitted into the soil generate the settlement greater than CMC piles. When the settlement between the soil and column became equal at neutral point, maximum structural load shall be balanced by the positive friction and tip resistance to stabilize the foundation without exceeding the allowable settlement limit. This paper describes the behaviour of soil reinforcement with CMC column and their installation process with reference to a project at the Dry Bulk Terminal Port, San Pedro- Abidjan (Western Africa). Methodology of CMC, requirements of Ground Improvement, arrangements and outcome of this method are presented in this paper.

Sep 1, 2022

By T Vijayakumar, Vipul Dobhada, Rajesh Patel, Swarnadip Dey, Naveen Babu D

The most challenging scope of any bridge project in marine or inter tidal zone is to construct sub structure like well Foundation, group pile, pile cap etc. Similarly, it also affects the marine environment/ecology to a great extent. Understanding the level of difficulties and aiding to provide an environment friendly solution, various options are analysed to overcome these and found mono pile to be the best alternative in this context. Generally, the foundation type of any bridge constructed in river, marine or intertidal zone in India is preferred for group piles. For the first time, monopile is being accepted as the foundation of bridge in India at Mumbai Coastal Road Project. The diameters of the monopiles used in this project are 2.5 m and 3.2 m. Hence, the challenges involved in monopile construction and experiences to overcome it are worth to share. Here, a brief discussion on environmental, geological issues and the needs of monopile as the foundation of bridge has been discussed. Furthermore, the monopile construction stages and confirmation of monopile capacity through different load tests have been elaborated.

Sep 1, 2022

By Lenin T., Madhav M. R., Padmavathi V.

Use of PVDs and preloading on the ground can significantly reduce the time taken for ground to consolidate. Many soils in situ are lightly overconsolidated, with overconsolidation ratios (OCR) ranging from 1.0 to 2.0 due to various reasons such as glaciation, ground water level fluctuation, aging, cyclic loading, creep, erosion, cementation, etc. The effects of overconsolidation ratio are analysed in this study. Compression index and consolidation coefficient are important parameters in determining time – settlement response of soft soils under preloading and with PVDs. These parameters are typically estimated using oedometer tests on samples, with the assumption that the results represent the entire deposit. The in-situ time-settlement plots at different depths are used in the back analysis for estimating compressibility and consolidation parameters of in situ ground, resulting in more representative values that reflect the deposit's overall behavior. From observed time versus settlements plots, variations of compression index and coefficient of consolidation with depth of a deposit are presented. Estimation of compression index with depth is possible based on different OCR values as shown in this study. Barron (1948), Asaoka methods are used to estimate the coefficient of consolidation with flow in the radial direction.

Sep 1, 2022

By Venugopal Bonani, Kumaran M., Thomas John

Liquid storage tanks are usually located in nearshore or coastal regions with soil profiles containing thick layers of compressible soils. These storage tanks are usually of large diameter up to 90m and carry high loads, and the tanks are supported by heavy deep foundations such as piles. These structures are subjected to huge lateral loads due to wind and earthquake, and any damage to storage tanks with highly inflammable liquids leads to disastrous condition. So, it is important that the top layer of soil (up to the fixity depth) should be strong enough to provide the required lateral load capacity to the pile. In a project for constructing LNG terminal in Odisha containing 2nos of 89m diameter LNG storage tanks supported with pile foundation located near to coastal region, for improving the lateral capacity of existing soil, the top 3m was replaced with compacted engineered fill (GSB). The site was a filled-up area with dredged soil from seabed, the top 5m-10m were soft to medium stiff clay with SPT N less than 10. The lateral design load on pile was 534kN under free head condition. Actual lateral capacity for the strata was around 200kN under free head condition which was less than required capacity as per structural requirements. Therefore, for improving the lateral capacity of pile the top 3m soil is replaced with well compacted engineered fill (GSB) in layers of 150mm and the capacity is proved by conducting initial and routine lateral load tests. This paper describes the properties of the engineered fill used and how the lateral load capacity of pile was improved to meet the design requirement.

Sep 1, 2022

By Viswanadham B. V. S., Babu K. V

Wind energy is one of the most economical renewable energy sources. In order to support wind turbines onshore or offshore open-ended monopile foundations are widely used. Unlike conventional structures, wind turbine foundations experience a large magnitude of lateral loads in the order of 20 % to 30% of total vertical loads. The presence of soft clayey layers at shallow depth along the coastal region, offers lesser lateral load resistance to monopile foundations. One option to enhance lateral load capacity is by introducing fins to the outer surface of the monopiles. Studies pertaining to lateral load response of finned piles in clayey soils are very sparse. This paper presents some of the numerical model studies on the lateral load response of monopiles and finned piles in soft and stiff clay. In the present study, three-dimensional finite element analyses were performed on monopiles as well as finned piles. Analyses were performed in clay with different consistency varying from soft to stiff. Pile material is mild steel for all analyses. The pile section modeled as linear elastic material whereas soil was modeled as Mohr – Coulomb constitutive model with non-associated flow rule. Monopiles and finned piles having four and eight fins with different fin sizes and configurations are considered during the analyses. Finned piles advantage over monopiles to resist lateral load is highlighted in the present study. The results have shown that fins are effective to enhance the lateral load carrying capacity of monopiles and also it reduces the bending moment in monopiles for a given design load.

Sep 1, 2022

By Jakub Szary

Excavation and shoring adjacent to the above-grade Gilmore train station and elevated guideway was undertaken in 2019. A perimeter secant pile cut-off wall was constructed to a depth 37 m (121 ft) below ground surface consisting of 1.0 m (3.3 ft) diameter drilled piles spaced 750 mm (2.5 ft) on-center, tied back with soil anchors, and reinforced with W610 steel sections every 4th pile. A bracing/jacking system was also constructed to support 3 free-standing guideway caissons within the excavation. An automated instrumentation program was installed to monitor movements of shoring walls and train infrastructure in real time and consisted of a robotic total station, inclinometers, tiltmeters, strain gauges, extensometers, and anchor load cells. Baseline monitoring was able to establish diurnal and seasonal movements within the structure, strongly correlated with temperature. The system actively monitored various shoring elements and train infrastructure in real time and alerted the project team when values exceeded predetermined threshold values. Remote reconfiguration of the automated system allowed for more frequent monitoring during jacking of Pier 29 in March 2022. Monitoring data was in agreeance with on-site manual surveying results and jacking dial gauges, and proved to be a reliable monitoring system for construction applications.

Sep 1, 2022

By Heman Manchanda, Jyoti Agarwal

Several infrastructure projects are under construction in India; many of them involves construction of deep foundations like reinforced concrete and steel piles to support super structures. As most of the piles being constructed in India are reinforced concrete bored piles, there are always uncertainties relating to the quality of construction, and in this case non-destructive methods to ascertain quality of piles becomes very crucial to success of any project. Non-destructive pile testing is becoming more and more popular with growing technologies wherein geophysical techniques and wave propagation theories are being used for pile quality and length analysis. Low-strain pulse echo method and cross-hole sonic logging testing are two pile integrity testing techniques being currently practiced in India which are cost effective and provides reliable near accurate results if analyzed properly. Paper presents current practices being adopted in India for conducting these two tests, highlighting the critical site considerations and analysis techniques. The paper also discusses various execution and interpretation challenges faced by practicing engineers and recommends a way forward.

Sep 1, 2022

By Amit Srivastava, Monica Malhotra

In a congested city or urban area, so called “lifeline of the city”, i.e. Gas, Electricity, telecommunication, as well as other utilities or facilities are supplied or transported underground through buried pipes or utility tunnel. Sometimes these buried pipes or utility tunnels are deep underground and interfere with the foundation of new structure. It is highly probable that a pile foundation is placed near an existing underground buried pipe or utilities tunnel and may influence its load bearing capacity. Hence, estimation of reduce load bearing capacity of the pile foundation placed near the existing buried conduit or utility tunnel is a complex soil-buried structure interaction problem. It is further complicated owing to uncertainty in estimation of geotechnical parameters of foundation soil due to measurement and testing errors, inherent soil variability and model transation. Under such circumstances, load bearing capacity is best assessed in probabilistic framework or through reliability analysis. The present study demonstrates how concept of response surface method (RSM) in conjunction with Numerical Analysis and First Order Second Moment (FOSM) methods can be combined to per the reliability analysis. The study answers the following question “reliability in reduction in the load bearing capacity of single pile placed near the existing underground pipe or utilities tunnel”. It is demonstrated that the approach provides first hand ination on the reduction in the load bearing capacity and then estimate the reliability of that estimation in terms of an index called Reliability Index (). Such preliminary investigation can be useful for advocating the detailed analysis as well as in the decision making for relocation of pile foundation.

Sep 1, 2022

By Gustav Jahner, Michael Baltrusch, Norbert Hoffmann

Near the port city of Whitby in the north-east of England, Anglo American (AA) is setting up the deepest mine in the UK, which will have a depth of 1,500m. The purpose of the project is to extract and transport polyhalite, both underground, and to market it globally. As part of the construction works, BAUER Technologies Ltd, the UK subsidiary of BAUER Spezialtiefbau GmbH, constructed three different shafts using the diaphragm wall technique, with depths of up to 120m. In order to ensure the specified vertical tolerance of maximum 200mm, several measurement methods were applied, and the results were documented in a 3D model. Complex de-sanding plant technology and specially developed polymer products were adopted to regenerate the trench supporting bentonite-slurry.

Sep 1, 2022

By S. A. Villalobos, F. A. Villalobos, and L. E. Aguilera

Rockburst events have been a serious problem for many years in many mines worldwide, and in particular at El Teniente mine in Chile. El Teniente is the largest copper mine in the world, located in the Andes Cordillera where high stress levels are present due to intensing mining activity in addition to complex geology. Consequently, the study and management of the rockburst threat are necessary. In this work, the case of the Diablo Regimiento (DR) mine within El Teniente is studied. The energy capacity of dynamic support systems is determined for different tunnel geometries based on two kinetic methodologies, using data from DR. Initially, rockburst potential is determined by means of a stress analysis around different tunnel geometries through the boundary elements method. In the first methodology a yielding zone (YZ) is estimated for each excavation geometry using the finite element method FEM. The second methodology involves the definition and determination of a critical strain energy (SE) around each excavation geometry using a FEM numerical analysis. In both cases, peak particle velocity PPV is estimated by a scaling law, which is subsequently adjusted due to tunnel amplification effects. According to the results, and knowing the working energy capacity applied in DR mine, it was found that the values of energy capacity for the rock dynamic supports were better estimated by the YZ-PPV approach than by the SE approach.

Sep 1, 2022

By G R. Ballantyne, G Lane

Dry milling circuits that include high pressure grinding rolls (HPGR) or vertical roller mills (VRM) and air classification have replaced dry ball milling in cement production, but how do they compare to wet milling and classification circuits in mineral processing plants? Two case studies are presented that compare the energy efficiency, wear, liberation and capital cost of dry and wet milling circuits. In both case studies the VRM and HPGR consume half the energy of a wet tumbling mill for the same duty. However, the dry classification system tends to significantly erode the energy benefits. A number of improvement opportunities are presented that have the potential to improve the energy and capital efficiency of dry milling circuits. These improvement opportunities focus on the dry classification system that consumes significant energy in heating and fan power requirements and requires a large proportion of the footprint.

Aug 24, 2022

By D K. Weatherley, A N. Mainza, I Govender, L M. Tavares, M S. Powell

It is understood that rocks do not instantaneously transport along a grinding mill and are consequently not perfectly mixed, but this is conveniently overlooked in mill modelling. A lack of understanding of the transport phenomenon and the difficulty of modelling realistic transport in a complex tumbling system, contribute to this. Visual observation of segregation in AG and SAG mills and measured lag time of mill response to changes in feed provide evidence of the influence of axial transport within mills. Incorporating this lag in dynamic models should underpin dynamic simulation of milling circuits for design and for model-based control. Limitations and errors in predicting the influence of increased power via mill length versus diameter, inability to predict pebble production, and a lack of the differential in residence time across rock sizes and competences, all contribute to inadequate design prediction that can be especially acute for large Autogenous mills. Examples of dramatically under – and overloaded pebble regrind circuits and the inability to predict pebble load in AG milling discouraging the application of this energy-efficient option, point to the need for predictive modelling of breakage by competence linked to transport through and out of mills. Incorporating progress in granular flow and mixing, coupled to computational advances enable models to be based on complex breakage and transport models at high spatial resolution. This allows mechanistic models to simulate thousands of times faster than real time, opening the door to more accurate mill design, including dynamics in process simulation and to live simulation for process control – all with advanced mechanistic models. The value of grasping this opportunity is not easily refuted.

Aug 24, 2022