Search Documents

By Grant L. Anderson, Richard C. Rice, Richard L. Jentgen

"Data for underground mine-hoist ropes determined in the Ontario Special Rope Tests were obtained, encoded and analyzed statistically. Prior 10 refined statistical analyses, these data were subjected la characterization studies and preliminary analyses to allow trends to emerge that could be used to guide and facilitate the refined analysis. The data were characterized by determining distribution s for a wide range of variables including remaining strength, service life in terms of lime and hoisting cycles, outer-wire torsion values, elongation during tensile testing, diameter reduction, location of strength loss and the strength lasses associated with corrosion rating and lubrication rating , This paper describes the more important relationships between remaining strength (or, conversely, strength loss) as the dependent variable and some of the principal independent variables mentioned above.IntroductionBoth productivity and safety in underground mines could be improved if mine-heist rope Iife and reliability could be predicted more accurately . As a result, hoist-rope failure processes and their effects on rope life and remaining strength need to be quantified and related in such a way that improved retirement criteria can be developed. This is true whether the failure is incipient or actual or whether the failure mode is by corrosion , wear, fatigue or a combination of these factors."

Jan 1, 1984

By D. P. Lindroth

The Bureau of Mines is engaged in research on ground probing radars for detection of geologic hazards in advance of mining. Penetration distances and interpretation models depend on the dielectric properties and wave propagation characteristics for coal measure stratified media. Relative dielectric constants and dissipation factors were measured under ambient conditions for Pittsburgh Seam coal measure rock over the frequency range of 20 to 100 MHz by the susceptance-variation method. The rock types measured were representative sedimentary rock located above the Pittsburgh Coal Seam. Extreme values for the computed attenu-ation distance ranged from 1.7 m at 100 MHz for siltstone to 230 m at 20 MHz for a particular limestone.

Jan 1, 1984

By P. L. Woolf

Seven evaluation tests with blast furnace iron bearing burden materials are described. The effects of pellet strength, fines in the burden, decreasing slag volume, pellet size, eliminating stone with superfluxed sinter, and eliminating stone by prefluxing the pellets were determined. Fluxed pellets and fluxed sinter made with the same ore fines were compared. The tests were conducted under cooperative agreements between the Bureau of Mines and North American steel companies. The objectives were to improve blast furnace practice, expand and develop understanding of the operation and theory, quantify the effects of changes, and explore the limitations of operability. This work was part of an extensive program of blast furnace research in experimental blast furnaces at Bruceton, PA conducted in the years 1958 to 1967.

Jan 1, 1984

By Terry A. Kirk

"This paper describes Derrick High Frequency Vibrating Screens and their process performance in grinding circuit applications. The benefits of screen sizing in closed circuit grinding are illustrated by case histories from a wide spectrum of mineral industries.INTRODUCTIONHigh capacity, reliable wet screening equipment is increasingly in demand by the mining and allied industries for separations finer than 1/.7 5mm (I/ mesh). The continuing search for improved energy efficiency and reduced steel consumption in comminution has Jed to greater scrutiny of every aspect of circuit design and operation, including the classifier efficiency (selectivity) function.Derrick Manufacturing Corporation has been developing high frequency screening machines designed specifically for grinding circuit applications since 1973. Successful installations are currently operating in iron ore, copper, coal, uranium, phosphate and other extractive industries."

Jan 1, 1984

Control dust generated during undercutting in salt mines without causing ore-solubility problems that result from excessive water use. Approach A foam generator was developed to provide a reliable foam to control dust on cutting machines used in mining water-soluble ores. The system was designed to keep total foaming agent/water mixture flowrates below the flow-rates characteristic of water-only systems. The foam generator consists of a reservoir to hold the premixed agent and water, a metering pump, and a small compressor to aerate the mixture. The system is compatible with all cutting machines. How It Works One of the current wet-bar techniques, the through-the-bar trickle system, pumps water through a pipe in the cut-ting bar to its tip placing the water behind the kerf. If the pipe conducted foam effectively the foam would be released in the kerf where it would mix with the cuttings and the dust produced by the chain. For improved foam delivery, however, it is recommended that the pipe be replaced with an external channel welded along the top of the bar. This provides excellent dust control while avoiding the accumulation of copious quantities of foam in the heading. The system is very simple. The foam generator is a 50-gallon tank filled with a mixture of water and foaming agent. The mixture is pumped through a wye fitting to a second line where it is mixed with compressed air, (300

Jan 1, 1984

By M. J. Laurila

The concentration of low grade iron ores to pellets or sinter fines suitable for blast furnace feed or direct reduction is highly energy intensive and costly in terns of both size reduction and separatory processes. Large equipment with high throughputs are required to make the fine grinds and multi-stage separations economical. Control of these circuits is essential to producing a high grade product. As a result, iron ore concentrators possess some of the more sophisticated instrumentation for process control in the mineral dressing industry. These instruments must characterize flowstreams of up to 8,000 gpm where 80% of the particles are less than 50 µm. The past decade has been one where enormous strides have been made in automated control of iron ore plants. This paper reviews state-of- the-art control systems for crushing, grinding, magnetic separation, froth flotation and sizing/classifying circuits. Trends toward computerization and plant automation in response to a dismal outlook for North American steel production are also examined.

Jan 1, 1984

By Robert L. Skaggs

Sixteen nonaqueous techniques conceived to replace the current aqueous scheme for separating hafnium and zirconium tetrachlorides were re- viewed and evaluated by the Bureau of Mines. The methods are divided into two classes: separation by fractional volatilization of the tetrachlorides, which takes advantage of the higher volatility of hafnium tetrachloride; and separation by chemical techniques, based on differences in chemical behavior of the two tetrachlorides. The criteria used to evaluate separation methods were temperature, pressure, separation factor per equilibrium stage, complexity, compatibility with existing technology, and potential for continuous operation. Three processes were selected as being most promising: (1) high-pressure distillation, (2) extractive distillation from a molten salt, and (3) preferential reduction of gaseous ZrC14. Any of the proposed nonaqueous Hf-Zr separation schemes must be supplemented with additional purification to remove trace impurities.

Jan 1, 1984

By J. A. Herbst

Ball mill grinding circuits can be subject to upsets that arise from variable characteristics of the feed ore. These upsets are transients in critical circuit variables such as ball mill mass holdup, circulating load, sump level, cyclone efficiency and product particle size. They may occur frequently so that the operation is continuously fluctuating or they may be of such magnitude that some of the equipment is overloaded, resulting in shutdown, or an undesirable product particle size. The feed ore characteristics that influence ball mill circuit behavior in this manner include the grindability of the ore, the eventual transport characteristics of the ore in the mills and the feed ore size distribution. Control strategies for grinding circuits using conventional proportional-integral (PI) control have limitations to their effectiveness in controlling against feed ore disturbances. The first of these are the interactive nature of two or more control loops on a single circuit. Under some circumstances they begin to fight each other, increasing control error and settling time. PI control loop gain constants can be tuned to give best response for some set of conditions but once these change, as they would with a change in the feed ore, they are no longer the "best" ones (Shinsky, 1967). Due to these limitations, alternatives to conventional PI control strategies have been investigated for grinding as well as other mineral processing operations. These alternatives, all computer-based, include self tuning regulators, decoupling control and optimal control (Herbst and Bascur, 1983).

Jan 1, 1984

By W. E. Pittman

The Bureau of Mines, as part of its Health and Safety Technology Program, is conducting research on the use of ground penetrating radar (GPR) for mine hazard detection. GPR offers a possibility of mapping immediate below-surface geologic conditions, including faulting and other anomalies, thereby exposing potential safety hazards to miners. This report summarizes a literature review of the current status of GPR research in and outside the Bureau.

Jan 1, 1984

By M. R. Meyer, W. T. Walter

A great deal is known, in a qualitative sense, about the performance of CMI EB-36 centrifuges. The manufacturer can give reliable guidance for the proper operation of its centrifuges and can give general estimates of expected product moisture and recovery. Quantitative estimates of the effects of changes in the various operating parameters are more difficult to find. The engineer faced with designing a preparation plant may be without the specific data needed to make decisions. For example, to obtain optimum product moisture when drying 9.5 mm X 595 µm (0.4 in. x 28 mesh) coal the centrifuge manufacturer recommends having no more than 5% -595 µm (-28 mesh) material in the centrifuge feed. They know that more -595 µm (-28 mesh)material in the feed will cause higher product moistures, but they usually cannot quantify the increased moisture or describe the shape of the product moisture versus -595 µm (-28 mesh) in the feed curve. This study was conceived to provide quantitative information on the EB-36 centrifuges, focusing on product moisture, recovery, and size degradation. All of the centrifuges tested were Model EB-36 dryers from Centrifugal and Mechanical Industries Inc. (CMI), with feeds in the nominal 9.5 mm x 595 pm (0.4 in. x 28 mesh) range. These are typical centrifugal dryers in this application, and many were available for testing.

Jan 1, 1984

By Dennis A. Long

Slip and fall accidents are a major cause of lost-time injuries associated with large mobile equipment in surface mines. An evaluation of the safety hazards associated with getting on and off large surface mining vehicles showed that most of the accidents occur at the point where personnel attempt to mount or dismount the machine at ground level. The major hazardous design conditions were identified as excessively flexible supports for lower steps or rungs, inappropriate ground-level-to-first-step distances, poor step designs, access designs that use vehicle components as steps or walkways, and inadequate hand- rail and guardrail designs, Additional hazards are introduced by the lack of proper maintenance of ladder hardware and the work practices of operators in carrying articles while mounting and dismounting the vehicle. This Bureau of Mines report describes the design and in-mine testing of improved access system for large mobile mining equipment.

Jan 1, 1984

By Edward F. Redente

Several research projects have been conducted in the western United States to determine the optimum soil replacement thickness for reconstruction of rangeland and cropland. However, the information gained from these studies tends to be site-specific and not broadly applicable. Moreover, the possible interaction between soil thickness and mechanical and fertilizer manipulation of the overburden has not been adequately studied. To meet these information needs, research was initiated at Trapper Mine in northwestern Colorado in 1980 to study vegetation response to soil thicknesses of 15,30,45, and 60 cm and five manipulations that included disking, ripping, and fertilizing. All crops were harvested at peak standing crop and then weighed in the laboratory. Wheat grain yields were highest when soil thickness was 45 cm and the soil and overburden were ripped. Alfalfa yields appeared to be highest when overburden was disked and fertilized and soil was replaced to a thickness of 60 cm. For range vegetation, standing crop biomass was highest when overburden was ripped and soil was replaced to 60 cm thick. However, optimum performance was obtained from the maximum number of species and life forms by disking overburden and replacing 15 cm of soil. The performance of most range plant species has improved over the three years of the study. When the results of this study are compared to the results of other soil thickness studies, we can conclude that selection of management practices should be influenced by local climate, local soil and overburden conditions, type of crop or vegetation to be grown, and specific management goals for that crop or vegetation.

Jan 1, 1984

By Daniel Houdouin

Data is frequently collected in mineral processing plants in order to evaluate operating performance or to model process units. Metal concentrations, circulating loads, products flow rates, classifiers efficiencies, flotation units recoveries, grinding mill efficiencies are typical parameters calculated from plant data. The validity of these calculations depends strongly upon the reliability of the data used for that purpose. The objective of this paper is to illustrate that flowrates, efficiencies and rate parameters of mineral processes are more reliable when calculated from balanced data rather than from raw data. Using variance-covariance matrices of balanced data produced by automatic mass balance packages (including flow rates, concentrations, percentage of solids and size analyses), variances of separator efficiencies (flotation or classification) and of mill grinding rates are derived. The variances are compared with those of variables calculated from raw data. The advantage of using balance data is illustrated with real data from flotation, grinding and classification units.

Jan 1, 1984

By William R. Bond

The pressure/vacuum lysimeter is being used as an effective vadose zone monitoring device for mining heap leach facilities, tailing disposal ponds and tailing waste sites. Their use has proven reliable for baseline data collection, early warning leakage detection and analyzing geochemical variations in the vadose zone. The lysimeter structure utilizes a closed cylindrical chamber made of PVC or inert material. The soil water intake portion of the cylinder is made of a porous material of low permeability. The application of vacuum or pressure to the unit is via two access tubes from the ground surface. Available soil moisture is drawn by vacuum through porous material into the lysimeter chamber and then collected from the access tubes. Case studies show their usefulness for monitoring around a uranium tailing pond constructed in glacial till material, under heap leach pads and pregnant, barren, and overflow ponds, and investigating the movement of contaminant moisture through old tailing deposits. Relatively easy to install and sample, regulatory agencies and facility operators are accepting and negotiating for their application as a site integrity monitoring device and unsaturated zone research tool. Their use at heap leach facilities lends credibility to solution balance calculations when considering a leachate loss of 5 or 10 percent can make or break a mine's profitability.

Jan 1, 1984

By N. P. Weymont

A first step towards using advanced control and optimization techniques at Kaiser Aluminum's Baton Rouge Plant has been the decision to utilize digital process control equipment exclusively throughout the plant. This paper describes the philosophy and strategy which has been used to successfully implement this program for both existing plant facilities and plant expansions. Some of the problems that have been encountered include system selection, vendor support, soft- ware development, system security and system reliability. How these problems arose, were overcome and how they can be prevented in future projects is discussed. A key element of the success has been the organization of the technical, engineering and maintenance efforts and also training has been found to be extremely important. Finally, the effect of these experiences upon present thinking is discussed.

Jan 1, 1984

By Henri S. Swolfs

INTRODUCTION In this paper we present preliminary results of a research program in site characterization methodology. We are interested in under- standing the response of discontinuous rock to mechanical, hydrologic, and thermal loadings. To carry out such a study we selected a field site with simple geology, uniform distribution of lithologies, and easily verifiable boundary conditions on temperature, fluid flow and stresses. The spatial distribution of fractures at the site was established and tests were conducted to determine the temperature field, hydrology, rock-mass properties, and in situ stresses. As part of the study selected borehole instruments were compared to assess their performance and reliability. SITE GEOLOGY The study area is in the eastern part of South Table Mountain, a mesa near Golden, Colo. The exposed cap rock is a single lava flow of uniform thickness (6-7 m) that rests on the clastic sediments of the Denver Formation (Van Horn, 1976). The surface of the cap rock (N. 75º E., 3º S.) is topographically featureless and slopes south- southeast; drainage is predominantly downdip and punctuated by occasional contact springs. The age of the lava flow is 64-65 m.y., or early Paleocene. Paleo- botanic evidence confirms the upper part of the Denver Formation as Paleocene (Van Horn, 1976). "Rapid-rock" analyses of core samples from the lava flow at three depths (0.2, 3.3, and 5.8 m) suggest a uniform chemical composition throughout with an increase in the Fe2O3/ FeO ratio (1.05 to 1.60) with increasing depth, reflecting the existence of a perched water table in the lava flow, To identify the rock

Jan 1, 1984

By M. J. Beus

The Bureau of Mines, under a cooperative agreement with Hecla Mining Co., is conducting a rock mechanics study of the 6,200-ft-deep circu-lar, concrete-lined Silver Shaft in northern Idaho. The objective of the project was to instrument and evaluate lining behavior and rock de-formation when a deep shaft is constructed in a high in situ stress field and anisotropic rock mass. Rock mass displacements were moni-tored with multiple-position borehole extensometers. Liner stress and strain were measured with concrete pressure cells and embedment strain gauges. Field data from the 5,955-ft test level show that rock displacement is controlled by rock mass anisotropy. Liner stress and strain levels reflect the high in situ stress field as well as nearby station and raise construction. Maximum stresses measured in the lining, as a result of shaft excavation, are about one-third of its compressive strength. Subsequent loading pocket excavation resulted in signifi-cantly increased stress and strain levels in the liner. Continued monitoring and preliminary analysis of the data indicate that concrete-lined, circular shafts are stable for the high, unequal horizontal stress fields and rock anisotropy encountered in deep-level mining. Adjacent development work can be expected to significantly alter the initial stress and displacement conditions.

Jan 1, 1984

By J. F. McCoy

As mining develops into deeper and hotter regions, the safety and health of miners require that the workspace be cooled. Toward this end, this program has successfully developed a high performance, low maintenance spray cooler of 5000 cfm nominal capacity. Further, a series of four 25,000 cfm, nominal capacity, spray coolers has been built and mine tested with satisfactory results. The smaller coolers have been patented and become commercialized with 50 units currently in service. The concept has been developed independently overseas with an unknown number of units in operation.

Jan 1, 1984

By M. Cross

INTRODUCTION The results of the Japanese dissective investigations have [l-4] transformed our understanding of how the blast furnace operates. These studies revealed an internal structure of the furnace burden with five main zones, as illustrated in Figure 1. In the granular zone the charged material retains its structure whereas in the cohesive zone the iron ore particles are at advanced stages of reduction and form a semi-molten mass with a relatively high flow resistance. In the active coke zone molten iron and slag flow through a matrix of loosely packed coke. The raceway is a relatively small void space generated by displacement of coke due to the hot blast momentum, whilst the hearth is packed with coke, slag and molten iron. [ ] It is now well appreciated that furnace control is largely achieved and maintained by using the burden charge distribution to determine the gas glow distribution within the furnace and, hence, the shape and extent of the cohesive zone. In fact, Wakayama et a1 [5] of Nippon Steel Corporation state that optimum furnace operation is synonomous with the formation of a desirable cohesive zone shape, which in turn is almost solely determined by the burden charge distribution and its mechanical properties [6]. Much of the development work on operating furnaces since the dissective investigations has been oriented towards the identification of external furnace measures which reliably predict the shape of the cohesive zone. Currently the most popular measures are top gas temperature, velocity and CO/CO, ratio profiles [5]. More recently pressure distributions as evaluated from a series of wall measurements down the height of the furnace are also being utilised [7] to identify the position and shape of the cohesive zone. A great deal of emphasis has been placed upon achieving a consistent quality in the burden charge materials, establishing a suitable set of operating conditions and only making changes when forced to, ie., the operation for some reason moves outside a desired operating range or the production requirements change. Operational control schemes based upon this philosophy (eg., Kawasaki's GO-STOP system [8]) have been remarkably successful at achieving both high production rates and relatively low fuel costs. Mathematical models have long been used as tools to assist in the analysis of the blast furnace process. Although, the models have been useful in post-operative analysis and for identifying trends, etc., they have not proved reliable for detailed design criteria or as the basis for effective control schemes. Such mathematical models have moved from simple statistical correlation, through overall and stagewise heat-and-mass balance calcu-

Jan 1, 1984

Provide the mining industry with a wireless surveying system for increasing efficiency in the drilling of methane drainage or exploration boreholes. Approach The Bureau of Mines has pioneered the technique of methane control by drilling long, horizontal drainage holes from within the mine complex. It was recognized during the early drainage projects that a major portion of the drilling operation was dedicated to hole surveying. In some cases more time was actually being spent on the surveying operation than on drilling. The large amount of time required for hole surveying was the result of having to pump an instrument to the bottom of the hole, then retrieve it with an attached wire line. Naturally as hole depth increased, so did the amount of time needed to perform the survey operation. If the survey operation could be improved it was obvious that overall efficiency in drilling of long, horizontal methane drainage holes would be greatly increased. The Bureau of Mines, therefore, developed, fabricated and tested in an operating coal mine a permissible wireless survey system specifically designed for small diameter methane drainage drilling. The prototype survey system was completed in 1982 and was given the IR-100 Award by Industrial Research and Development Magazine. A second generation survey system is currently being constructed using updated state-of-the-art electronic technology. The second generation system will be more portable, more reliable, easier to maintain, and less costly.

Jan 1, 1984