Search Documents

By C. A. Rowland

"Plant owners and operators, plant designers and grinding mill manufacturers are giving much attention to the design and manufacture of autogenous and semi-autogenous grinding mills, particularly the mills that have large diameters and draw power up to 10,000 hp and greater. Reliable designs giving long operating lives are required in today 's ore processing plants.This paper reviews bench-scale and pilot-plant testing to determine first if the ore is suitable .to be ground by these methods and then reviews the data obtained from pilot-plant testing that is used to select the mills and the grinding circuit. The paper then discusses the use of the pilot-plant results to design the mills. The most important pilot-plant data used for mill design are power and the amount of ball charge to be used. The mill size selected is a combination of these factors. Pilot-plant data not only establish power requirements, but can be used in the selection of the type of drive, variable speed or fixed speed, and the operating procedure to be followed. This leads into the mill control circuit to be used. The total charge in the mill, the type of drive and mill discharge arrangements are needed in the calculation of stresses and bearing loads. Conclusions reached from pilot-plant work are used to obtain data for process design, and autogenous and semiautogenous mill design should be part of any test program incorporating either or both of these grinding methods."

Jan 1, 1981

By David T. Swanson

The term "pressure tunnel" in the broad sense includes all hollow spaces, aligned along an axis and surrounded by rock, which are suitable for pressurization. In particular, this category includes: • horizontal or slightly inclined water pressure tunnels; • vertical or inclined pressure shafts; • pressure chambers or shafts of surge chambers; and, • compressed air storage tunnels. The main problems in the design and construction of pressure tunnels result less from their length or size than from the requirement for watertightness and, dependent upon this, reliability in operation and economy in construction. Where the lack of sufficient overburden does not permit the rock to accept the internal pressure in the tunnel, or where this pressure is so high that the watertightness is in doubt although the stability of the tunnel shell is not in question, a pressure tunnel must nevertheless be reinforced. Surge chambers, pressure tunnels and tailraces which are subjected to relatively low internal pressure, usually not much in excess of 1.5 MN/m2, are eminently suitable for construction in post-tensioned concrete. Pressure shafts, which as a consequence of the high water head are subject to a considerable maximum service pressure, are usually lined with a steel tube, a considerable proportion of the internal pressure being transmitted to the rock by backing concrete. TYPES OF LINING FOR PRESSURE TUNNELS In general, the type of lining will depend upon the nature of the rock. As a result, pressure tunnels usually are not uniform in con-

Jan 1, 1981

By E. R. Cole

This Bureau of Mines investigation was prompted by the need forr a stable anode for electrowinning metals, particularly zinc and copper, from acid solutions. The polarization behavior of Pb-Ag (1 pct Ag) anodes in H2SO4 and fluoride solutions was determined as the first step in the development of such an anode. A Luggin capillary, dc power supply, high-impedance voltmeter, and other equipment standard to an electrochemical laboratory were used in this study. It was determined that during polarization, a relatively hard, stable coating of Pb02 was formed on the surface of the lead-silver anode and the rate of formation of this coating was considerably enhanced by the presence of fluoride ions in solution. Subsequent investigations at the Bureau of Mines Rolla Research Center resulted in the development of a Pb02-coated titanium (Pb02-Ti) anode. Results of this effort were presented in Bureau of Mines Report of Investigations 8111. Additional data resulting from extensive testing of the Pb02-Ti anodes, as well as process improvements and innovations, are included in this report. The anodes were considered generally unsatisfactory for zinc electrowinning because of lower conductivity, higher oxygen overvoltages, and shorter in-cell life as compared with the Pb-Ag anodes now being used in industry. However, the PbO2-Ti anodes were used successfully to oxidize waste chromium solutions and to electrowin copper.

Jan 1, 1981

By Lloyd A. Morley

This final report concludes the documentation under Grant G0155003 and details research not covered under foregoing report volumes. The first chapter lists all other reports. The following chapters are divided into three major research tasks: Continuous Safety Monitoring Systems, Battery and Battery-charging Safety, and Mine Power System Transients. The monitoring chapter discusses the prediction of power-system failures. The battery chapter details work on battery-box stresses, battery chargers, and the elimination of electrocutions. The final chapter covers transient instrumentation, distribution transients sources and suppression, and utilization transients on mine power systems.

Jan 1, 1981

By W. I. Enderlin, P. O. Jackson, J. A. Glissmeyer, K. B. Olsen

A reliable estimate of radon emissions to the environment from underground uranium mines was obtained through measurements of radon in ventilation air at 24 mines and from estimates of radon release from other mine sources. The total production of U308 from the mines sampled represents about 63% of the total U.S. production from underground mines (1978 statistics). Wide variation in the radon emission rate per unit of production was found from mine to mine. Using the total radon emitted and U308 produced by all mines sampled, an average of 26.7 Ci of radon was emitted per ton of U309 produced. The investigation includes a brief study of the sources of variation of the emission rates. A statistically significant relationship was found between the measured radon release rate and the cumulative ore production at several mines.

Jan 1, 1981

By M. Y. Fisekci

This paper concentrates on subsidence measurements, applied over the thick and steep seam mining in the Rocky Mountains Region of Western Canada. The studies to date indicate that two new subsidence monitoring techniques appear to be the most suitable methods for these conditions. The computerized telemetry and aerial photogrammetry systems are being tested for the reliability of the systems during the winter months within the net- work of laser surveying over the workings of the new hydraulic mine.

Jan 1, 1981

Improve the Bureau-developed system for locating and communicating with miners trapped underground following a mine disaster. Approach Include in the wireless system a portable second-generation transceiver that is more reliable, compact, easier to deploy and operate, and ruggedized to withstand a mine environment. How It Works In an emergency, the new transceiver is snapped onto a caplamp battery for power. (Normally the 1 1/2-pound transceiver is either carried by the miner or is strategically located in the mine.) Its antenna wire, coiled inside the transceiver container, is removed and deployed in a roughly square configuration around a coal pillar or on the mine floor. The antenna consists of 300 feet of lightweight wire, which provides a large magnetic moment while remaining intrinsically safe, The photograph shows the

Jan 1, 1981

By G. R. Peterson

The Bureau of Mines evaluated the potential supply of cobalt from known domestic resources, both as a primary product from some deposits and as a byproduct from others, and found that U.S. production could play an important role in meeting U.S. cobalt needs by the mid-1980's. This production would be of a relatively short duration, however, with production declining significantly before the year 2000. As part of the study, a tonnage-price relationship was developed indicating the quantity of cobalt that could be produced from known cobalt-bearing deposits at various primary commodity prices and at a 15-percent rate of return on the required capital investment. All capital and operating costs are calculated in August 1980 dollars, and commodity prices are based on August 1980 prices. Known U.S. cobalt-bearing deposits which represent the current U.S. cobalt reserve base contain some 310,800 metric tons of cobalt in slightly over 1 billion metric tons of demonstrated mineralized material. Approximately 37 percent of the cobalt contained in the reserve base is considered recoverable using existing technology. Of this quantity, some 87,000 metric tons of cobalt is economically recoverable assuming a cobalt price of $25 per pound, a copper price of $1 per pound, and a lead price of $0.40 per pound. Assuming that the cobalt price decreases to $15 per pound, keeping copper and lead prices constant, the quantity that is considered economically recoverable declines to some 45,700 metric tons. Domestic cobalt consumption in 1979 was 7,900 metric tons (17.4 million pounds). Currently, no primary cobalt is produced from domestic resources, and none has been produced since 1971.

Jan 1, 1981

By Benjamin W. Haynes

Materials from phosphate rock mining and processing were analyzed for fluorine and uranium content as part of the Bureau of Mines program to more effectively recover resources from mining and mineral processing reject materials. The analysis of both feed and waste materials generated in the beneficiation and acidulation of phosphate rock was performed to obtain information on the disposition and concentration of these elements in phosphate rock processing streams. Fluorine was determined by a distillation-titration method and by ion chromatography. Uranium was determined by the dibenzoylmethane (DBM) method, the reliability being confirmed by roundrobin analysis of samples within Bureau of Mines research centers. National Bureau of Standards (NBS) Standard Reference Material (SRM) 120b-Phosphate Rock was also analyzed for fluorine and uranium to verify procedures and results. Fluorine values ranged from 0.3 wt-pct in gypsum filter cake to 3.7 wt-pct in phosphate rock concentrate. Uranium ranged from less than 5 µg/g in gypsum filter cake to 200 µg/g in a dried clay slime.

Jan 1, 1981

By C. Cánepa

In the treatment of many problems related with the optimization of a given ore dressing process, microscopic studies can provide invaluable assistance. Such studies are generally carried out through mineralogical determinations both qualitatively and quantitatively. Frequently the solution of a specific problem requires the combination of these in adequate proportions. Often the nature? of the problem poses some conditions regarding the way the microscopic determinations are made in order to yield useful information. Most publications applied to mineral beneficiation show results of ore microscopy without mentioning the methodological details involved in the determinative work and therefore it is not possible to judge their reliability and/or their relevance. As methodology must necessarily change from case to case, it is very important for the microscopist to identify first the direct and indirect mineralogical information required to solve the problem. Without such guidelines selection of methods for the qualitative and/or quantitative determinations cannot be made.

Jan 1, 1981

By H. L. Fraser

A review of the possibilities of performing microchemical analysis in thin sections using a combination of scanning transmission electron microscopy and energy dispersive spectroscopy of x-rays is given. Particular attention is paid to the factors that limit accurate analysis at the highest spatial resolution. As an example of the use of these techniques applied to a potential problem in minerals processing, the identification of iron pyrite and pyrrhotite particles in Illinois, Herrin #6 coal is presented.

Jan 1, 1981

This publication summarizes, for all interested parties, the research, development, and demonstration in-house projects programed by the Bureau of Mines for fiscal year 1981 (October 1, 1980 - September 30, 1981) under its Minerals Health and Safety Technology program. The objective of these projects is to provide an ordered and sequenced series of advances toward the Bureau's overall goal of providing the system technology required to create a healthier and safer working environment for the Nation's mining and minerals processing workers.

Jan 1, 1981

By F. Weinberg

"The recent development of the continuous casting process for steel has required basic understanding in a number of areas in the metallurgcal sciences. In some areas, information is still lacking. The success of the application of basic knowledge and research to the process is evidenced by the fact that a large percentage of the steel now produced in the world is produced by continuous casting.A number of areas in which metallurgical science has contributed and is currently contributing to better design and control of the continuous casting process and leading to a better quality product will be considered. These include:(a) heat transfer studies of the entire casting process;(b) fluid flow in the tundish, strand and liquid metal stream;(c) solidification structure and segregation;(d) strength and ductility of steel at high temperatures related to bulging and cracking; and(e) problems related to horizontal casting developments.IntroductionThe continuous casting of steel is a relatively new technology in steelmaking. It is now used extensively throughout the industry. In Japan, for example, continuous casting accounts for approximately 40010 of steel production, and this value is expected to increase to over 50% in the near future . New steel plants are now designed to use continuous casting exclusively. This means the process must work well and be completely reliable, because all the steel produced must go through the caster.The development of the continuous casting process in a short period of time has required concerted research and development in many areas . I shall cite a number of examples of these developments and refer to work done in Canada when applicable. No attempt will be made to review all of the research in continuous casting, nor refer to all of the workers in the field.The developments in continuous casting are based in many cases on metallurgical science, as described below. The use of metallurgical science in these developments is qualitative, in that concepts and idea s are used, as opposed to quantitative values calculated from fundamental equations. In general, most metallurgical problems are too complicated to enable fundamental equations to be used without the introduction of uncertain approximations and boundary conditions in the calculations.Starting at the beginning of the steelmaking process, very extensive research and development has been carried out to produce liquid steel of the required composition and temperature. The replacement of open hearth furnaces with BOF furnaces reduced refining time from many hours to roughly 30 minutes for 250 tons of steel. Two BOF furnaces effectively enable a continuous flow of steel to be available in a plant, essential for the introduction of the continuous casting process. This area of research will not be considered here."

Jan 1, 1981

By A. H. Rhoades

The modern polarizing microscope with such accessories as cameras, infrared devices, reflectance and/or transmission photometers, indention hardness, and heating stage is used to characterize coal, coke, and other carbon forms. It allows characterization of coke by-products, such as tars and pitches and their insoluble residues. A useful product of the microscopic approach is the coal petrographic analysis which permits the prediction of coke strength carbonization pressure and volume change. Carbonization tests are expensive, time-consuming and require large amounts of coal. Tests on the coke show it to be strong or weak but give no indication of why. Petrographic analysis requires grams of coal and yields data that indicates why the coal produces coke of a given quality. Small samples from drill cores are sufficient for petrographic analysis. These data are also used to optimize blends for coke production. When coke-plant problems occur, ~he microscope can be used to check the coal blend proportions, as well as for weathered coal. Microscopy is useful in spore correlation work which may be a prerequisite to sound coal reserve estimates. Dispersed vitrinoid reflectance studies are used to determine the degree of organic metamorphism which serves to establish oil and gas deadlines. Tars and pitches are examined microscopically for the amount of normal solids as well as the size of undesirable carry-over solids resulting from pollution abatement practices in coke works. The microscope is also used to study coals for gasification and liquefaction.

Jan 1, 1981

By Calvin J. Konya

Overloaded blastholes and insufficient stemming are major factors in flyrock accidents at surface metal and non-metal mines, Accurate measurement of blasthole depth, stemming height, and water depth would reduce the overload and the probability of blow-out, flyrock, excessive ground vibration, and airblast. Problems result because current measuring systems are inaccurate and often difficult to used A literature survey determined measurement techniques and blasting parameters prior to 1970. Similar data were gathered for current practices in 11 iron mines, 30 copper mines, and 92 quarries. Most operations used a cloth tape to measure borehole depth and stemming height; approximately 10% of the operations had dry blastholes. Alternate measurement techniques were evaluated and discussed. Candidate measuring techniques with best potential for improvement over the present weighted tape method are disposable tapes or string chains, automated readout tapes, modified sludge level indicators and acoustic resonance methods.

Jan 1, 1981

By Jon G. Bredeson

A survey of electromagnetic noise reports was performed and a summary of the results are given. Industrial concerns were surveyed for techniques to minimize the effects of electromagnetic noise and are presented. The common types of communication links used in mines today are presented. A mathematical development was presented which determines the probability of bit errors versus distance for various types of communication links designed for in mine use. The probability of undetected errors for the protocols of the communication links is given together with burst error detection.

Jan 1, 1981

By Robert W. Gordon

This report describes the results and conclusions of the further development of a lightweight probe drill for use in anthracite mines. Improvements to the drill previously developed under Contract H0282044 were made and tested at an Eastern Pennsylvania mine. These improvements were: 1. Better hole cleaning due to the development of an air-water mist flushing system. 2. The application of roof drill bits to allow drilling through rock seams and lenses. 3. The development of a quick coupling drill system which reduced total steel change time. 4. Adaptation of a swivel to the drill anchoring system which greatly reduced set-up time between holes. With these improvements the probe drill demonstrated its ability to drill the required 11 holes in one shift. It also gained miner acceptance as a viable underground working tool. The probe drill proved to meet all of the design requirements of portability, low weight drilling controllability, structural integrity and reliability. In addition to its ability to drill the required probe pattern, the probe drill has the capability of drilling long holes. By drilling several holes over 80 feet deep the probe drill has demonstrated a potential for use in robbing pillars and for methane drainage.

Jan 1, 1981

By Robert W. Bruhn

State and federal regulations require that surface mine overburden be investigated in advance of mining for naturally occurring earth materials that are detrimental to animal and plant life or to uses of water. Proper identification of these toxic materials is necessary to permit development of environmentally sound reclamation programs. Intensified use of present laboratory methods to meet anticipated testing demands would be both costly and time consuming. This paper discusses the desirability of and general requirements for a geophysical system capable of locating toxic zones in the overburden of surface mineable lands of the Northern Great Plains Coal Province. The paper (1) identifies the types and character of naturally occurring overburden substances that must be investigated in advance of mining, (2) discusses the economic justification for development of a geophysical system to replace or to complement conventional laboratory test methods, and (3) discusses the potential applicability of downhole geophysical methods to overburden analysis.

Jan 1, 1981

By E. C. Strycula

Solid-state equipment offers a number of potential advantages in the coal mining industry. These advantages can only be realized, however, through careful and judicious design of the control and protection circuitry. Problems relating to the interaction of solid-state equipment on the electrical system and the special design considerations which apply to solid-state circuitry are examined. Design guidelines are provided for solid-state applications in the areas of: (a) equipment operated from a DC trolley wire, (b) drive systems for surface mining equipment, (c) AC motor starters, and (d) electromagnetic interference.

Jan 1, 1981

By H. E. Dresch

This report summarizes the work accomplished under Bureau of Mines contract H0188068. The contract required design and construction of a high voltage (7.5 KV) explosion proof cable connector for use on underground coal mine drag cables. A connector was constructed with elastomeric phase insulators that provide insulation shielding throughout the connector length. Connector housing was made of flame resist-ant cast poly urethane with no exposed metal components. Electrical and mechanical testing of the completed coupler resulted in satisfactorily meeting most of the design testing requirements.

Jan 1, 1981