Search Documents

By Mervin D. Marshall

A quick-reaction, mine permissible rescue vehicle (MERV) was developed for use by rescue teams. The MERV is a 6-wheeled, battery-powered unit with life support equipment and instrumentation; designed for a two-man team, with provisions for handling two victims or tools in a trailer. The vehicle is 100 inches long, 56 inches wide, and maximum height of 34 inches. It can be lowered down most mine shafts and has clearance to travel mine railways. The vehicle has power to all six wheels with power transmitted separately to either or both sets of wheels. Low-pressure, high-traction tires give the vehicle the ability to handle soft, muddy mine floors, flooded areas and significant obstacles, and can negotiate a 45% grade. Power and life support are sufficient for a 4-hour mission. The life support system is a commercially-available, approved unit currently used by MESA rescue personnel. A payout wire system provides communication between the vehicle and home base over a distance of 10,000 feet. On-board monitoring of carbon monoxide, methane and oxygen is provided, with master and individual alarms to warn of gas concentrations outside pre-set limits. A lightweight, water-tight trailer was developed for carrying victims or hauling tools and equipment.

Jan 1, 1979

During the past decade, since the appearance of Popoff's (1966) review of grade tonnage calculations, it has become evident that defining a new method which could be followed step by step by a technician and which would improve reserve estimation was not a simple thing to do. Some concepts have emerged though, and most definitions of ore reserve now require a statement of reliability (USGS, 1975; and Zwarten-dyke, 1976). Exactly how the reliability should be computed is not a straightforward process. It also became apparent that not only was reliability a requirement but that additional questions such as how to predict mining re- serves from geological reserves were to be asked. In fact what became obvious is that specific models have to be designed for each type of mine and for each type of question which is asked. Most methods can be encased within a unique general geostatistical, model, but it takes considerable custom tailoring, and there are still questions that are left unanswered. In this chapter, before giving techniques, we intend to first review what should be required from a grade tonnage calculation done at the exploration stage. If the final objective is still to specify a tonnage and grade, with eventually a reliability, many qualifications have to be made before quoting, and of course, calculating these two numbers. Then the currently avail- able methods will be reviewed and future trends will be shown; finally a few case studies will be given and recommendations about the choice of a model will be made.

Jan 1, 1979

By Herbert H. Einstein

Rock mass deformability is commonly predicted using correlations with RQD or other indices of rock mass quality, or by extrapolation from large in-situ tests. Based on the probabilistic description of rock masses empirically developed in Part I a new approach was attempted in modeling for predictions of deformability. This approach decomposes the rock mass into spatially variable joints described by probability distributions, and intact rock blocks. Stiffnesses and elastic parameters are associated with the joints and intact blocks respectively, and deformations built up by adding the contributions of each. This model allows relaxation of many of the simplistic geometric assumptions which constrain parallel attempts to model deformation in rock masses. The model has been applied to four standard cases in order to test its results against previously existing models, and to check whether it replicates empirical correlations. When joints are taken as parallel, common empirical correlations are closely approximated by the model output. However, the closeness to empirical correlation breaks down when variability of the jointing geometry is increased.

Jan 1, 1979

By A. J. Farstad

Characteristics of metal/non metal mines were evaluated to determine the suitability of applying the U.S. Bureau of Mines electromagnetic location system to the problem of locating trapped mines in metal/non metal mines. Statistical distributions of mine depths and overburden conductivities show that the existing USBM EM system is inadequate for most metal/non metal mines. Alternate approaches to trapped miner location in deep mines were identified and subsequent field tests were conducted at six (6) mines to evaluate their feasibility. The approach considered to be the most promising is one which utilizes the existing manpack transmitting system, modified slightly for a dual frequency output, in conjunction with a sophisticated signal processing receiver on the surface. The main advantage of staying with a "through the earth" approach is that the underground equipment can be kept simple, easily maintained, light-weight and inexpensive.

Jan 1, 1979

By James P. Ludwig

This report provides the results of a two year study of the projected time and cost requirements for new mine development in Wisconsin and is based on a unique blend of information from mining company officials, state regulatory agency officials and contractor experience. Through formal cooperative and review agreements with Kennecott Copy per Corporation, Exxon Minerals Co., U.S.A. and Noranda Mines Ltd., and the Wisconsin Department of Natural Resources plus informal arrangements with knowledgeable Wisconsin persons, lists of the tasks and subtasks required to plan a new mine in Wisconsin were developed. Times and costs were assigned to all tasks and subtasks and these data reviewed by all cooperators. Critical Path Method Diagrams were then developed for a generalized mining project. Total time and cost for the premine planning process was estimated to be 25..1 years and 223 person-years of professional time excluding public affairs effort respectively. By eliminating redundancies in the process and by increasing project efficiency through early public review and participation, recom¬mendations were made to lessen the time and lower the cost of premine planning. The streamlining recommendations could shorten the overall critical path length to 18.16 years and lower the cost to 208 person-years of professional time excluding public affairs effort. The estimated distribution of professional effort (cost) for mine planning in Wisconsin approximates 50.5% for traditional mine engineering tasks, 36.6% for environmental-regulatory tasks and 12.9% for traditional geological-exploration tasks.

Jan 1, 1979

By Jack L. Woodward

The evolution of surface mining equipment has resulted in larger, faster haulage units, loaders, etc., resulting in increased demands on steering technology. Careful analysis of these systems was warranted to determine if steering-related safety problems have been introduced. The objectives of this program were to: 1. Define the generic types of steering systems being used on mobile mining equipment used in surface mining operations. 2. Gather information on steering-related accidents in mining operations. 3. Assess the need for initiating government-sponsored research into steering system technology. A comprehensive literature survey was conducted concurrent with extensive contacts with mining operations, mining equipment manufacturers, steering system component manufacturers, and government agencies. A Technical Evaluation Group composed of representatives from the above organizations was formed to review the data gathered. It was concluded that the steering systems in use on surface mining equipment are reliable and do not present a safety problem. The Society of Automotive Engineers, Inc. is active in pre-paring voluntary consensus standards to assure that the minimum levels of performance are defined for industry.

Jan 1, 1979

This study assesses whether Narragansett Basin coal deposits could be developed commercially in the near future. To do this, we identify the potential market for the coal, assess the price these users would be willing to pay for Narragansett coal, and this price to the expected costs of producing Narragansett coal. The study concludes that the major market, New England utilities, could burn bituminous coal from Pennsylvania or West Virginia at a lower total cost than Narragansett Basin coal, assuming expected mining conditions and emission policies. Therefore, the study concludes that Narragansett Basin coal resources could not be developed economically in the next ten years.

Jan 1, 1979

Recommendations from 44 mining industry workshops are summarized and reviewed in the context of Bureau of Mines research and development programs on-going during the period 1974-1977. Approximately 1,000 specific recommendations for research and development are summarized in a systematic and comprehensive format appropriate for review by mining research and development program managers. Relevant Bureau of Mines research programs are briefly described and some opportunities for future research and development are identified.

Jan 1, 1979

By J. A. Kosek

Work has been conducted under Bureau of Mines Contract Number HO 357078 to develop instruments for detecting CO, NO and NO2 in a mine atmosphere, using fuel cell technology. The approach has been to optimize the fuel cell sensor configuration for the specific detection of CO, NO and NO2 in the presence of other mine gases utilizing recent advances in catalyst, electrode and solid polymer electrolyte membrane technology. Para-metric testing has been conducted on three electrode sensor cells to define performance and life characteristics as a function of temperature, feed flow and applied sensor voltage. Extended life testing has been performed on sensor cell configurations exhibiting favorable characteristics. Reliable, efficient gas sampling and electronic control circuitry has been fabricated for use with the sensor cells, and integrated into devices to meet the performance and design specifications for portable, battery-powered, hand held direct indicating gas detectors for use underground. Twenty of the production-type, direct indicating CO detectors have been tested and delivered to the Bureau of Mines under the present contract. Three prototype diffusion head CO monitors have also been delivered for evaluation under the pre-sent contract. The gas sampling pump and related parts have been replaced by a diffusion tube assembly in which CO reaches the sensing electrode surface by diffusion alone. In addition, delivery will be made of ten direct-indicating nitric oxide detectors and ten direct-indicating nitrogen dioxide detectors. These instruments are very similar in design to the direct indicating CO detector.

Jan 1, 1979

By Ralph B. Stevens

The objective of this 20-month program was to define the relationships between mine ventilation, temperature, humidity, ore properties, material's used in mine operations, etc., and the spontaneous combustion problem in underground metal mines. Tradeoff studies of availability, reliability, cost, and maintenance of spontaneous combustion protection sensors and telemetry were conducted, after which a prototype system was selected from four design alternatives. This selected system was then laboratory tested and demonstrated in an underground copper mine.

Jan 1, 1979

By Clifford B. Farris

The natural cementation strength of retorted oil shale is the focus of this investigation. The optimum retorting temperature and residence time to obtain natural cementation strength in retorted Green River oil shale from western Colorado were determined as follows: [Optimum Conditions for Natural Cementation Maximum Residence Obtained Retorting Time at Compressive Mode of Temperature Temperature Strength' Retorting °F °C hr psikg/cm-2 Direct 1,520 822 2.0 270 19.0 Indirect 1,530 832 2.9 325 22.8] 1 Scattered samples were tested at strengths as high as 463 psi (32.6 k /cm 2) (Run 8, indirect mode) and 406 psi (28.5 kg/cm2) (Run 48, direct mode), but these high strengths were not confirmed by nearby tests. Minus 0.5-inch (1.3-cm) Green River oil shale was heated in a differential retort under conditions simulating potential full-scale retorting processes. The variables investigated were retorting temperature, residence time, retorting mode, and shale grade. Samples of the retorted Green River oil shale were moistened to optimum plus 2% (25%) moisture, compacted to 95% Proctor density, sealed and cured at 100°F (38° C) for up to 40 days. Lower curing temperatures, which are likely in the field, would probably result in significantly slower development of cementation strength, and might lower the ultimate strength developed. However, these effects were not studied in this project. The cured samples were tested for compressive strength, and correlative equations were developed for the increase of compressive strength with curing time as a function of retorting temperatures and residence time. Petrographic analysis indicated that the cementing mechanisms may be the interlocking growth of acicular hydrated calcium aluminum sulfate crystals between the contacts of retorted shale fragments. Samples of the retorted shale were also tested for optimum Proctor density and moisture. Permeability and quality of the leachate of shale from typical runs were determined. The effect of use of retort rather than tap water on compressive strength and leachate after curing was determined. The retorted shale effectively filtered several mineral constituents from the retort water.

Jan 1, 1979

1. Domestic Production and Use: In 1978, 12 companies operated 31 primary aluminum reduction plants, with 3 firms accounting for 65% of production capacity. Washington, Oregon, and Montana accounted for 31% of the total capacity; Gulf Coast States 23%; Northern States 26%; and other Southern States 20%. Based on published producer prices, output of primary metal in 1978 was valued at $5 billion. Aluminum consumption by 25,000 firms was centered in the East Central United States. Of aluminum consuming industries in 1978, building accounted for about 25%; packaging 22%; transportation 23%; electrical 11%; consumer durables 8%; and other uses 11%.

Jan 1, 1979

By G. Gavan

Analysis of reported injuries for off-highway haul trucks indicated that 42.7% were slip and fall, and of these 34.1% occurred mounting and dismounting the machine. Redesign of the lower steps was concluded to provide the most overall improvement for increased safety and accident reduction. Various existing, innovative and conceptual designs were reviewed and evaluated. The most promising candidate designs were the four-spring supported lower steps and the center tube mounted lower steps. Both configurations proved to be viable designs as they passed successfully human factors and survivability tests conducted at a large copper mine.

Jan 1, 1979

By Wils L. Cooley

Two major grounding topics are covered: mine ground systems and ground-check monitors. Performance characteristics of ground-check monitors for high-voltage surface mine distribution cables and low-voltage underground mine trailing cables are evaluated. Over 20 commercially available monitors are studied to determine their utility. Several monitoring concepts are incorporated into an unusual monitor design, the prototype of which is described in detail. A comparative study of the effectiveness of several alternate methods of grounding surface mine equipment supports the system currently proposed by MSHA. An instrument design to measure earth voltage gradients is described, as well as an instrument design for measuring the effectiveness of dc haulage current return systems. An extreme analysis is made of techniques for measuring earth resistivity and resistance of safety ground beds. Electrolytic corrosion studies of earth electrodes are reported extensively also.

Jan 1, 1979

By E. K. Stanek

This report contains results of two major efforts related to electrical transients on mine electrical power systems. The first area concerns the use of digital computers to model mine electrical power systems and predict transients or duplicate field recordings of transients. Two existing general purpose circuit analysis programs were used. The first was the TRW Engineering System Simulator or TESS. The second was Electronic Circuit Analysis Program or ECAP. TESS proved to be superior to ECAP in several important characteristics, including system size limitations and modeling nonlinear elements. The second major topic covered in this report is the evaluation of commercially available surge suppression devices. These devices were found to be quite acceptable and guidelines for the selection and placement of surge suppressors were included. The final important item is a listing of the worst-case transients, from a design point of view, for ac and de utilization systems and ac distribution systems.

Jan 1, 1979

By Frederick C. Kohout

An advanced water-in-oil emulsion hydraulic fluid has been developed which meets defined laboratory performance criteria and which has given fully satisfactory results in a one-year underground mine test in two continuous miners. A novel method of monitoring fluid water content was demonstrated and incorporated into a test kit for use at or near the mine site. Test fluid fire resistance integrity as measured by the MSHA Schedule 30 procedure was maintained during the test and important fire resistance test variables identified.

Jan 1, 1979

By Ernest W. Hilton

The purpose of this investigation was to assess the environmental impact of the surface mining methods currently used in the steep-sloped areas of Central Appalachia: southern West Virginia, eastern Kentucky, southwestern Virginia and northeastern Tennessee. Comparisons are made between mountaintop/cross ridge mining, contour strip, augering and an innovative method surface shortwall mining which was attempted at Julian, West Virginia. Included in this final report are a discussion and analysis of current Appalachian production, reserves, and the extent of land affected on a county- by-county basis. Additionally, the seams within the steep sloped region have been assessed according to minimal standards of thickness, surrounding lithology, and areal extent to determine their amenability to surface shortwall mining. These seams have been tabulated with their ash, sulfur, and BTU content on a county-by county basis. Only minimal statements are made concerning quantity because of the narrow set of conditions required by the shortwall method. Other sections deal with the possible technical failings of an operational surface shortwall system based on field studies at shortwall operations, discussions with people experienced with shortwalls and research into ground control problems at sites where short- and longwall operations have been monitored. A final section details proposed additional research directions which the Bureau might take in the future.

Jan 1, 1979

By John H. Johnson

White Pine Mine section designated for exhaust emissions studies. The MTU Mine Air Monitoring Laboratory was used to gather temperature and C02 concentration data at 10 locations. The data substantiate the presence of strong buoyant forces of the hot exhaust gases which result in stratification in dead end headings. Diesel mine-vehicle tailpipe emissions were monitored in the laboratory by a portable tailpipe emissions measurement apparatus (EMA) assembled for in-mine use. The results were compared with simultaneous measurements by standard laboratory exhaust monitoring instruments. These results indicate that accurate field source quality control measurements can be obtained for CO2, CO and NO but NO2 results were low for all engine conditions. Diesel pollutant concentration data from the Orchard Valley Mine were analyzed and compared with data collected earlier in the White Pine and Brushy Creek mines. Lognormal frequency distributions and CO2-based concentration ratios and correlations were calculated. In the three mines compared, pollutant concentrations were distributed similarly, and concentrations appear to be controlled to present standards.

Jan 1, 1979

By Philip B. Grote

The deep ocean mining industry is in a pre-commercialization stage of development. In the context of a proper legal/regulatory regime, deep ocean mining system design, site survey, and operation technologies are capable of rapid evolution. The report recommends that the regulatory framework develop in parallel with the industry and presents a rationale for implementing this approach. The Government has several interests in deep ocean mining technology: (1) as a potential regulator, sound regulations should be based on an understanding of the technology; (2) as a potential monitor, survey technologies are relevant; and (3) as an estimator of strategic minerals supplies, it is important to understand the technology which allows economic access to deep ocean minerals. Thus, the major portion of the report presents an in-depth review of systems design, operations, and survey equipment and techniques.

Jan 1, 1979

By Mackenzie Burnett

The Brattice Window Method was used to measure the leakage rates of a total of 42 ventilation stoppings in 8 hardrock mines. Various types of stopping construction were evaluated. The following types are listed in order of decreasing effectiveness: 1) Cinder block, 2) Timber and mortar, 3) Timber and polyurethane foam, and 4) Timber and brattice material. There are slight differences in the effectiveness of the first three types, while the timber and brattice type is substantially inferior to the others. The repeatability of the Brattice Window Method was found to vary with physical conditions in the mine such as stopping location with respect to intersections, regularity of drift cross section, and the presence of hardware such as air and water pipes, timber sets and wire mesh. The Brattice Window Method is viewed primarily as a tool for estimating and comparing stopping leakages for the purpose of determining where repair efforts should be concentrated. A laboratory test program resulted in the derivation of several "rules of thumb" for employing the Brattice Window Method, which will aid in securing accurate and repeatable data.

Jan 1, 1979