Search Documents

By D. Randolph Berry

The objective of this program was to develop a system to extinguish coal mine fires by remote sealing of the underground passageways. The system developed had to be versatile enough to function under a wide range of operating conditions, including large variations in passageway geometry, depth of mine, water conditions, both in the mine and at the surface, and rubble in the mine passage. The system developed had to include instrumentation for the remote probing of the passageway prior to sealing, a system for sealing the mine passages, and instrumentation for remote monitoring of the quality of the seal during and after construction. These objectives were successfully achieved during this program. The remote mine sealing capability of the system was satisfactorily demonstrated in a field test conducted at the Eastern Associated Coal Corporation Federal No, 1 Mine in Grant Town, West Virginia.

Jan 1, 1973

By Howard E. Parkinson

In 1969, new coal mine health and safety legislation was enacted in the United States. As a result of this legislation, the Department of Interior, Bureau of Mines has carried out communications research aimed at developing whole mine communications for increased safety and efficient operation. The research has advanced and many promising results are now being demonstrated to the mining industry. However, there remains a challenge to further improve wireless communications within the mine workings and through the overburden above the workings. The objectives for future research and development will be discussed, together with the physical and operational constraints that new mine communication systems must face.

Jan 1, 1973

By Walter I. Enderlin

To economically extract ore from great depths in the earth while sustaining an acceptable working environment will require the development of new technology and equipment, involving large capital expenditures. Moreover, careful analysis and advance planning will be required. But, the literature is lacking in data pertaining; to the thermal properties of various host rocks and to quantities of heat generated by various underground heat sources. This types, of data is required to forecast nine heat loads during advanced planning and design. This thesis sets forth a practical method for evaluating underground sources of heat in deep mines and provides an improved information base. Moreover, seven topics for further research are recommended. The heat sources considered are: wall-rock, ground water, adiabatic compression, equipment, service lines, blasting, metabolism, curing of cement, and oxidation of sulfides and timber. Seven deep metal mines with high production rates and high heat loads were visited to obtain data necessary to assess their thermal environments. Mine records were examined, wall-roc:, temperatures were measured and a survey of the mine ventilating air and mine drainage was performed. Also, the thermal conductivity of wet and dry specimens of the host rock were measured in the laboratory. Data analysis disclosed that rock heat and adiabatic compression account for stout 60 per cent of the mine heat load at depth. Equipment currently contributes approximately 20 per cent; however, to offset increasing costs with depth, increased mechanization is anticipated. The treat from ground water averages 19 per cent and the contribution from blasting, metabolism and cement is negligible. Also, approximately [0] per cent of the increase in the enthalpy of the ventilation air is in the form of latent heat. Moisture, however, did not significantly affect the thermal conductivity of the rock specimens measured in the laboratory. Also, from the data, it is evident that a negative correlation exists between the thermal conductivity of the host rocks and the per cent of the heat load derived from the wail-rock. Furthemore, steady state heat flow renditions may be assumed in airways where there has been no major changes in the ventilation system for a period of two years or more. Under these conditions, the author found it more convenient and reliable to compute heat influx using the steady state equation for heat flow into a cylinder, rather than Carrier's method for transient heat flow, which is so often used.

Jan 1, 1973

A prototype EM Location System was fabricated and tested at the Geneva Mine near Dragerton, Utah. This system consisted of six manpack transmitters and six manpack receivers covering the frequency band from 900 Hz to 2900 Hz as well as a six channel receiver designed for use, in a helicopter. Tests showed that EM signals from lightweight (3/4 lb) transmitters could be detected both on the surface and from a helicopter through as much as 4450 ft of relatively high conductivity (2 X 10- 2 mhos/m) overburden. Furthermore, the resulting field strength profiles could be used to determine source location to within 150 ft of the actual surveyed location in the mine. Modifications were made to a Monitoring, Locating and Communications System being tested at the Bruceton Mine, Pittsburgh, Pennsylvania. These modifications have improved the performance and quality of the paging and voice telephony mode of the system. Subsurface receiver modifications have improved reception of voice downlink signals.

Jan 1, 1973

By Horace T. Reno

This information circular surveys the iron are industry of the world. It presents a comprehensive statistical record through 1970 of the U.S. iron ore industry and world trade patterns. The supply position of the United States and the other principal industrial countries of the world are summarized; detailed information is given on iron are production, consumption, imports, exports, mine capacities, substitutes, properties, and uses. There is a generalized discussion of the technology of mining and smelting iron ore, with a selected bibliography on the current state of these arts. The circular contains a summary economic account of world iron are resources, and discussions of the structure of the domestic and principal foreign mining industries, iron are mine employment and labor productivity, research and development, legislation, government programs, and strategic factors.

Jan 1, 1973

By Lyman C. Hitchcock

The objective of this program was to determine the minimum luminance requirements for underground coal mining work from the working face to the first transfer point. The resulting data encompasses 114 visual tasks from conventional continuous and longwall mining methods representing the salient visual tasks found in the jobs listed. Cutter Operator Roof Bolter Face Drill Operator Airdox Operator Longwall Jackman Shuttle Car Operator Loader Operator Shot Fireman Continuous Miner Operator Longwall Head Conveyor Operator Longwall Tail Conveyor Operator

Jan 1, 1973

U.S. Bureau of Mines contract H0122053, "Improved Sensors and Fire Control Systems for Mining Equipment", was an investigative effort involving: ? Study of the fire problem on large mobile mining equipment ? Identification of equipment most prone to fire, to serve as a design case example ? Design of an improved fire protection system ? Demonstration of the developed system This effort was performed during the period June 1972 through May 1973, and was conducted in two phases. Phase I, June through November 1972, was devoted to identifying the fire problem and developing and evaluating design criteria. Phase II involved translating the design into hardware and demonstrating its effectiveness during actual fire tests, first on a wooden mockup of a truck, then on an operating truck at a working mine site.

Jan 1, 1973

By Laurence G. Trudell

Geology and oil-yield data are presented for a 58-square-mile area encompassing the U.S. Department of the Interior oil-shale leasing program tracts in the western Washakie Basin, Sweetwater County, Wyo. Lithology and oil yields of samples from three Bureau of Mines coreholes are evaluated and correlated with Kinney Rim surface sections measured and sampled by the U.S. Geological Survey. Minable sections of oil shale averaging up to 25 gallons of oil per ton crop out on Kinney Rim in the Laney Member of the Green River Formation. Thick oil-shale sections in the Laney Member that average 15 gallons per ton represent 155 million barrels of oil in place per square mile. In the lower part of the Green River Formation the Tipton Shale Member contains a 20-to 40-foot section averaging 15 gallons per ton. Beds of high-volatile C bituminous coal up to 6 feet thick are present in intertongued parts of the lower Green River Formation and upper Wasatch Formation.

Jan 1, 1973

The United States is rapidly depleting many of its most important minerals and fuels. The first two Annual Reports by the Secretary of the Interior, under the Mining and Minerals Policy Act of 1970, made us acutely aware that the natural resources that enabled this Nation to attain an unprecedented growth in terms of economic well-being, and to set an example of independent strength through the democratic process, are finite. Once they are depleted, large imports will be required. Simultaneously, competition for available supplies, especially of petroleum, is increasing in the expanding European and Japanese industrial communities and in the underdeveloped nations of the world. Even before the crisis of late 1973, the oil-producing nations of the world, principally in the Middle East, but including Canada and Latin America, were recognizing that the worldwide need for crude oil, petroleum products, and natural gas could be translated into an unprecedented economic bargaining position. Thus, the members of the Organization of Petroleum Exporting Countries (OPEC) raised the price of their crude twice during the first 6 months of 1973. By yearend the energy situation had be-come acute, and it seemed probable that regardless of current political developments, the era of cheap energy was over.

Jan 1, 1973

By J. W. Allen

This report reviews the work performed on Task M of Bu-Mines Contract H0220073 to develop an engineering model of a surface and subsurface communications system for normal mine operations and for post disaster rescue operations. The system concept provides for one-way transmission of digital information between a number of identifiable subsurface terminals or subcenters and a single surface station. It also provides 2-way voice communications between the subcenters and the surface station. The basic communications link is electromagnetic signaling through-the-earth, but the system is also capable of using mine phone lines as an alternate link. Engineering models of three subcenters and one surface terminal (see Figure 1-1) have been fabricated in order to demonstrate the system's performance. The system concept, however, permits up to 20 subcenters to be incorporated if desired. Additional subcenters are also feasible for large mines if they can be deployed in the mine to operate on a noninterfering basis.

Jan 1, 1973

By A. J. Farstad

The principle objective of the research effort described herein was to identify as rapidly as possible a practical trapped miner location system. Much effort has been expended in the past on the development of a highly sophisticated seismic location system [1] for trapped miners. Field tests of this system have shown that the location accuracy is limited by a combination of seismic velocity anomalies, timing errors, and in general by the relatively weak nature of the signals received at the surface. It was first felt that similar propagation anomalies would be experienced by electromagnetic systems, but to a greater extent than the seismic. However, preliminary tests performed by Westinghouse on the Operations and Maintenance Program, Contract No. H0210063 in 1971 and 1972, indicated that an electromagnetic solution to the location problem may be more feasible than a seismic solution. Thus a more concentrated effort was launched in 1972 and 1973 to more completely determine the feasibility of electromagnetic location systems for trapped miners. Two different approaches to the location problem were undertaken on this program: (1) A pulsed electromagnetic system was developed by the Special Systems Division of Westinghouse in Baltimore, and (2) a Continuous Wave (CW) System was developed by Westinghouse Georesearch Laboratory (WGL) in Boulder, Colorado. Part I of this report will deal only with the development and results of CW Location System developed by WGL. The CW Location System was field tested at three eastern coal mines and at one western hardrock mine. The maximum overburden depth penetrated during these tests was 990 feet at the Robena No. 4 mine near Waynesburg, Pennsylvania. The earth conductivity at this mine was measured to be 1. 1X102 mhos/m, which combined with the deep overburden make this mine representative of expected worst case conditions for a coal mine EM location exercise.

Jan 1, 1973

By Alfred Petrick

This study gives an analysis of the copper system byproducts and discusses the identification and classification of byproduct metals and their supply systems. Arsenic, platinum-group metals, silver, gold, selenium, tellurium, molybdenum, rhenium, uranium, aluminum, magnesium, and byproduct copper, lead, and zinc from complex ores are covered. The report describes several metallurgical systems, the marginal and incremental products costs of byproduct subsystems, industry structure and organization, and the historical data on price, consumption, and supply. Supply curves are presented for about one-half of the byproduct metals studied. The study develops a conceptual framework for analysis by reviewing the present concepts of byproduct supply and the related price theory. It gives the sources of supply of the individual byproduct metals to indicate the importance of the byproduct supply to the total supply. Mills, smelters, and refineries processing byproduct materials for their metal content are identified by geographic location and company ownership, The study also includes information on the reserves-resource base supporting byproduct output, reserve estimates, and the demand aspects of each byproduct metal.

Jan 1, 1973

By James H. Cobbs

The utilization of large diameter drilled holes for mine shafts seems to have had its beginning in Europe about 1850 (28) where the mining industries of Germany and The Netherlands first used drilled shafts. Recent shafts in softer formations of diameters as large as 25 feet and as deep as 1, 700 feet have been drilled in both The Netherlands and Germany. The first shaft drillers utilized cable tool or churn drilling techniques which limit both hole diameters and drilling speeds. Though some churn drilling of shafts is still performed, rotary drilling has been the dominant technique for many years.

Jan 1, 1973

By Llewellyn A. Rubin

ROUTINES AND SUBROUTINES A- 1 Wait Loop (Wait) A- 2 Receiver Processing (RCVP) A- 3 Control Panel Sequence (CPNL) A-4 Interrupt Routine (INTRP) A- 5 Math Processing Routine (PROC) A-6 Input Constants for Math Routine (CONI) A-7 Angle Conversion Routines (LVERT) A- 8 Display Routine (DSPY) A- 9 Message Print Auxillary Routine (MESSO) A-10 Auxillary Subroutines (AFUTC and AGETC)

Jan 1, 1973

By Cloyd D. McDowell

The Federal coal Mine Health and Safety Act of 1969 has been criticized by those who say it goes too far in controlling the activity of private enterprise and by those who say it does not go far enough in eliminating fatalities and accidents in an accident prone industry. Possibly a better evaluation of this legislation lies somewhere in between. From the viewpoint of the coal industry it can be said that through the efforts of those engaged in mining, both the operator and the miner, the year 1969 marked a record year in mine safety with only 190 fatalities and a frequency of 0.84 per million man hours exposure. This outstanding achievement compared to any previous was the result of a determined effort on the part of a concerned industry to improve its reputation as being the most hazardous industry in the nation. After the effective date of the Act, March 31, 1970, the Bureau of Mines assumed complete control of all safety and health activities of the mining industry. Unfortunately, there was no improvement in the safety record of underground mines in 1970 with the total of 255 fatal injuries and a frequency of 1.04 for the year. The number of fatalities declined to 177 in 1971 but the number of underground coal mines had declined from 5,955 to 2,268 during the two year period. Meanwhile, surface mined coal increased from about 38% of total production in 1969 to over 50% in 1971, keeping the annual production of coal at a normal level but involving fewer men.

Jan 1, 1973

"THE GOLD MINING REGION of Timmins - Val d'Or, astride the Ontario-Quebec border, has long suffered the effects of rising costs during the period when the U.S. price of gold was fixed at $35 per ounce. The federal government, through such assistance programs as that set up under the Emergency Gold Mining Assistance Act (E.G.M.A. ) in 1948, has subsidized the gold mining communities of Canada for a total of over $300 million to March 31, 1972. Of this, the Timmins - Val d'Or ""gold belt"" has received more than twothirds, almost $220 million. In spite of these continuous subsidies, only 12 gold mines are still producing in the Timmins - Val d'Or belt, whereas 71 mines have received subsidies for some period since 1948. The vital question is how the communities previously supported principally by the mining of gold will survive in the long run, as many of the older mines either are already depleted or are quickly becoming so. With the rising price of gold on the 'free market in recent months, prospects look a little brighter for the time being. Even with the increased official price of U.S. $38, which made the maximum government subsidized price about $48 per ounce, gold mines have not sold any gold to the government since January 1972 and some stopped doing so months before that. The populace of the region has not been enthusiastic about relocation nor about extensive retraining programs in the past and probably will not be in the future. So, when the remaining gold mines become depleted, the old problems of community depression will remain."

Jan 1, 1973

By Robert J. Brison

The intent of this paper is to try to answer the complex question: "How much grinding capacity should be designed into a new mining - milling project?" Much work has been devoted to the technical aspects of grinding, the "how" of grinding. But, in the writers' opinion, the economically important subject of optimizing grinding capacity in mill design has not received the attention it deserves, at least not in published literature. For the purpose of this paper it is necessary to distinguish clearly between optimizing operation and optimizing design. Optimizing operation involves making the best use of the available plant and equipment. Much excellent work has been done and is being done in this area. In operation, one can make tradeoffs of production rate and recovery, or recovery and grade, to maximize profits. However, this must be done within the limitations imposed in the design stage. Flexibility is limited by the existing plant. In project design, on the other hand., there are no preexisting physical limitations except as imposed by nature itself; the planners and designers have considerable latitude in their efforts to optimize the overall project. They have complete control over a large number of important design variables from the mine to the finished product. The grinding process design is one of these variables. It not only determines the capital cost charges for grinding and the maximum grinding capacity that operating management will have to work with, but also determines the range of capability of the auxiliary equipment, which fixes the degree of flexibility possible in operation. This paper is concerned with optimizing design rather than operation. The terms "optimum" and "optimize" are sometimes used in a technical sense in connection with grinding, recovery or grade. In this paper, these terms are used only in the economic sense. In this age of working large deposits of ever lower grade ores, it is in¬creasingly essential to design projects and plants for optimum economics, based on the most applicable economic. criteria. Since grinding represents a large part of both capital and operating cost of the project, and largely determines percentage recovery of metal, it should be included as one of the factors in optimizing the project design. This paper is written primarily with reference to medium to large copper concentrators employing conventional wet grinding. However, the principles involved should be applicable to other ores and other methods of grinding.

Jan 1, 1972

By F. G. Schwartz

The Bureau of Mines developed a rapid and precise method for predicting storage stability of motor gasolines. This method resulted from the investigation of many analytical techniques as well as a study of fuel composition and fuel component gum-forming mechanisms. The first section of this bulletin discusses the development of the prediction test through its several phases, including revision of the standard 110° F storage test; attempts to develop a modification of the ASTM D525 induction bomb test; and the ultimate abandonment of this procedure with the adoption of the 16-hour oven test that was both precise and rapid. The second section comprises a discussion of further studies of fuel com- position, including the reactivity of certain sulfur compounds and hydrocarbons to form gum. The compositions of various gums and inorganic deposits are reported in terms of elemental analysis and spectroscopic examinations. The reactions of tetraethyllead with selected hydrocarbons are also reported.

Jan 1, 1972

By Fred Leighton

The least squares method of rock noise source location presented is shown to be more accurate and reliable than standard direct solution methods. This method is particularly effective in improving solutions from rock noise locations outside of geophone array boundaries. A least squares solution for a medium .in which the seismic velocity is the same in all directions is also presented. In this special case, one can solve for both the source coordinates and the velocity.

Jan 1, 1972

By Gary N. Greenfield

This morning, gentlemen, I should like to discuss resin anchors of a type introduced to North America approximately 2-1/2 years ago. We shall also briefly review the basics of mechanically anchored rockbolts so that a general comparison may be made. Previous efforts with synthetic resins were aimed at aiding a mechanical Or "point" anchor, obtain a better purchase in the rock mass. Resin cartridges of the type to be described in this paper are capable of achieving point anchorage or full encapsulation of mine roof or rockbolts. Of significance, therefore, is that unlike a mechanical bolt, placed and tensioned, celtite rockbolts may be fully grouted and tensioned or left untensioned in the installation sequence. Our principle effort has been to offer this system to mining and civil engineers who have encountered difficult rock conditions and wish to reinforce strata to achieve a greater degree of permanence and safety.

Jan 1, 1972