Search Documents

By C. Gatlin, N. E. Garner, A. Podio

Experimental data from single chisel blows on Leuders limestone are presented. A pressure chamber, similar in design to well known microbit drilling chambers, was utilized to impose variorcs stress states on the sample. Confining pressure of zero to 10,000 psi and borehole pressures from zero to 5,000 psi have been used in the studies. Pore pressure was zero and the rock samples dry in all instances. Force-displacement records and visual examination of the craters indicate that the mode of failure depends on both confining and borehole pressure in certain ranges, ranging from brittle, through a transition, to near plastic. The mode of failure is reflected in the observed blow force and energy data, as well as the shape of force-penetration curves. INTRODUCTION A previous paper' presented initial data from the project on which this paper is the second report. While the first paper dealt with impact studies on synthetic rocks, the literature cited there is also pertinent to this paper, but will not be listed again in order to avoid needless repetition. This paper presents experimental data from single chisel impacts on limestone at certain simulated wellbore stress states. Specific variables investigated were combinations of borehole and confining pressure, crater geometry, a narrow range of impact velocity and the forces required to drive the chisel into the specimens under the varying conditions. EXPERIMENTAL PROCEDURE The same basic apparatus described in our earlier paper, except for the pressure vessel, was used in this study. Fig. 1 shows the complete experimental system. Fig. 2 shows details of the pressure cell, which is quite similar to the well known microbit drilling chamber. The confining (overburden) pressure system provides independent pressure control over the sample except for two, 21/4 in. diameter areas located on the sample ends. These two areas provide a pore pressure entrance on the bottom and a striking surface on the top where borehole pressure can be controlled. The ends are isolated from the confining pressure by O-ring seals. The borehole and pore pressures are related through the striking surface; they will be the same unless a seal is deposited on the borehole surface, either a mud cake or some other impermeable membrane. In these studies pore pressure control was not used, as the rocks were dry and unsaturated in all cases. Rock samples were prepared from 4-in. cubes as illustrated by Fig. 3. The circular disks of adhesive vinyl plastic protected the impact surface from the resin coating (Scotchcast No. 2) and were removed just prior to each test. This procedure insured a fresh uncontaminated surface for the impact. Fig. 4 shows the dimensions and loading of the sample, including the concentrations around the "borehole" periphery (O-ring seal). The rock used in this study was Leuders limestone, of Permian age (Leonard), quarried near Leuders, Tex. Geologically, Leuders limestone is a light gray, fossili-ferous limestone (oolitic foraminifera1 biosporite). Its fossil content is 80 to 90 per cent and consists primarily of calcitornellid, ostracods, pelecypods and oolites with the remaining part intraclasts. There are hematite or limo-nite rims on some of the intraclasts. The porosity is approximately 20 per cent, but the permeability is less than 1 md. There is no apparent orientation in the structure. Triaxial tests have been conducted to determine the variation of the physical properties of Leuders limestone in three orthogonal directions', and it is known to be unusually isotropic and uniform. Physical parameters for this rock are: uniaxial compressive strength = 9,700 psi; F = 32 and C = 2,700 psi; where + and C are Coulomb equation values (t = C+u tan +). Impact tests were run under the combinations of confining and borehole pressures shown in Table 1. Samples were dry with atmospheric pore pressure in all cases. Tests, in which elevated borehole pressures were applied, used a single layer of household Saran-Wrap to prevent horehole fluid invasion into the sample. This proved to be simple and reliable. The blunt wedge used in all the tests was 0.75 in. long and had an included angle of 60" with a 0.05-in. flat. In addition, a sharp 60" wedge was used for all confining pressures at zero borehole pressure. The chipper speed

By K. H. Hiller

A rotational viscometer has been designed which perrnits the measurement of the rheological properties of drilling muds and other non-Newtonian fluids under conditions equivalent to those in a deep borehole (350F, 10,000 psi). The important mechanical features of this instrument are described, and its design criteria are discussed. The flow equations for the novel configuration of the viscometer are derived and the calibration procedures are described. The data and their interpretation, resulting from measurement of the flow properties and static gel strengths of homoionic montmorillonite suspensiom at high temperatures and pressures, are presented. Data are also presented for the flow behavier of typical drilling fluids at high temperatures and pressures. The pressure losses in the drill pipe and the annulus depend critically upon the flow parameters of the drilling fluid. This work demonstrates the need to measure these parameters under bottom-hole conditions in order to obtain a reliable estimate of the pressure losses in the mud system. INTRODUCTION The rheological properties of drilling fluids are affected by temperature and pressure, but the extent of these effects on the dynamic flow properties is not well known. Measurements of changes of the flow properties of clay-water drilling muds with temperature have been reported by Srini-Vasan and Gatlin.1 The temperatures reported did not exceed 200F, a limitation imposed by the apparatus used by these authors. The rheological properties of clay suspensions were measured at temperatures up to 100C by Gurdzhinian.' Neither the nature of the exchange ions in the clay suspensions nor the degree of purity were defined in his work, nor were the measurements extended to currently used drilling fluids. The lack of systematic measurements of dynamic flow properties at high temperatures and pressures seems the more surprising since during the last decade the importance of the control of the hydraulic properties of drilling fluids has come to be widely recognized. Very good mathematical treatments of the friction losses in drill pipe and annulus have been developed.3 4 These treatments are based on the assumption that drilling fluids behave as Bingham plastic fluids. Quite often this assumption is justified, while in other cases a power law equation pro- duces better fit than the Bingham model does. For convenience in applying viscometer data to pressure-drop calculations, the Bingham plastic flow equation is preferable and, therefore, has been applied to the data reported in this paper, although other equations may fit these data more accurately. In a Bingham plastic fluid the relationship between the shearing stress 7 and the rate of shear D is given by the following equation: where is the plastic viscosity and 4 the yield point. If 4 = 0, the equation for simple Newtonian flow, 7 = pD, is obtained. Two empirical constants are required for the description of laminar flow of a Bingham plastic fluid, and calculations of the flow behavior at high temperatures and pressures cannot be better than is permitted by the accuracy with which these constants are known. For this reason a high-pressure, high-temperature rhe-ometer has been designed to measure the plastic viscosity the yield point +, and the static gel strength S, at pressures up to 10,000 psi and temperatures up to 350F. The important features of its design will be described. The results of measurements on homoionic clay slurries will be discussed insofar as they are relevant to an understanding of the general flow behavior of clay-water drilling fluids. The results of measurements on some typical drilling fluids will be presented also, and their practical implications will be briefly discussed. DESCRIPTION OF EQUIPMENT MECHANICAL FEATURES A viscometer designed to measure the plastic viscosity, yield point and gel strength of non-Newtonian fluids must permit the measurement of the shearing stress t at any given rate of shear D. This is possible only if t and D are approximately uniform throughout the entire sheared sample. A Couette apparatus is the most convenient method of realizing this condition, as has been pointed out by Grodde." The "high-pressure, high-temperature rheometer" described in this paper is basically a rotational Couette viscometer that is immersed in a cell in which pressure and temperature can be controlled over the range of interest. Fig. 1 shows schematically the important features of the pressure cell and associated equipment. The heart of the instrument is the rotating cup. It is shown more clearly in Fie. 2. which revresents the lower one-third of the pressure cell (below the input drive shaft shown in Fig. 1), and it is shown in detail in Fig. 3. For measurements of dynamic flow properties, the rotating cup is driven by a 1/2-hp electric motor, which operates through a Vickers

By M. L. Harris

Coal dust produced during the mining process is a prime explosion hazard in underground coal mines. To inert the coal dust and prevent a catastrophic propagating dust explosion, rock dust is applied to the roof, ribs, and floor surfaces of mine entries. Currently, one determination of whether a mine is adequately protected from the coal dust explosion hazard is made by analyzing collected mine dust samples for percent total incombustible content (% TIC). A minimum of 80% TIC is required per 30 CFR 75.403. The as-received moisture of the dust sample is included in the % TIC. Moisture and humidity within a coal mine vary greatly with the seasons, with explosions occurring more frequently during dry winter months. This paper will discuss the fluctuations of the as-received moisture content of the mine dust samples collected by U.S. Mine Safety and Health Administration inspectors in 2010 and the observed fluctuations of the moisture content of rock dust within the U.S. National Institute for Occupational Safety and Health Office of Mining Safety and Health Research Bruceton Experimental Mine and the Safety Research Coal Mine over a one-year period.

By James C. Cawley

This National Institute for Occupational Safety and Health study was conducted to focus future research on the most significant electrical problems in the mining industry. Data from 1,926 mine electrical accidents (including 75 fatalities) that occurred between 1990 and 1999 were studied. Coal and metalnonmetal operator- and contractor-reported data are presented. All data used in this analysis were MSHA closeout data, except 1999, which were preliminary data.

By G. R. Pickett

Examples are presented which show that the velocity~ amplitude, attenuation and apparent frequency of several acoustic waves can be recorded in the borehole. Examination of such recordings, termed "character" logs, indicates that the wave types observed include a refracted compressional wave and a wave which travels with formation shear velocity. Laboratory data are used to show that compressional and shear wave velocities are dependent on porosity, effective stress and lithology; but that the change in reciprocal velocity per unit change in porosity is larger for shear waves than for compressional waves. We, therefore, conclude that. the accuracy of porosity determinations can sometimes be improved by use of shear wave velocities, provided that the shear wave amplitudes are large enough to delineate the shear arrival from the preceding compressional arrival on the character log. Borehole data are presented which show that the difference between shear wave and compressional wave reciprocal velocities can be used to predict porosities. This is a refinement which may allow the prediction of porosities from single-receiver acoustic logs without introduction of errors from borehole fluid traveltimes. Laboratory and field data are presented to show that the relationship between compressional and shear wave velocities can be used to indicate lithology. An example is presented to show that fractures usually cause a greater reduction in borehole shear wave amplitudes than in compressional wave amplitudes, an effect which may offer a more reliable means of detecting fractures. The complexity of the borehole acoustic wave train can rake presently available cement bond logs highly sensitive to the gate and bias settings used. The character log offers a means to circumvent possible misinterpretations by recording all amplitudes, from which the interpreter can select the appropriate data for evaluating the cement bond. Character logs may also be used as a quality control for open-hole transit-time logs when existence of small compressional wave amplitudes interferes with the proper functioning of bias-controlled timing devices. Evaluation of the potential uses of character log data is not complete; but a character log presented in a form convenient for routine use would be a desirable addition to currently available logs. To summarize, possible applications for such a log in formation evaluation include the following (1) quality control of transit-time logs, (2) refinement of porosity predictions, (3) determination of lithology, (4) improvement of fracture detection and (5) improvement of cement bond evaluation. Suggestions are made regarding the requirements for a suficient but practical character log for routine use. INTRODUCTION Acoustic logs have become a widely used porosity tool in formation evaluation. In addition, there is a growing application of acoustic logs in cement bond evaluation and fracture detection. These applications have mainly involved the use of logs of first-arrival transit times and amplitudes and have not included detailed studies of the complete signal. The purpose of this paper is to show that significant benefits in formation evaluation can be gained by a more complete use of the acoustic wave train generated in the borehole by an acoustic logging tool. We hope that this discussion will also stimulate further development of logs suitable for routine use so that these benefits may be realized. Examples of acoustic wave train logs, termed "character" logs, are presented to show that several identifiable acoustic waves are present in the borehole. The measurable characteristics of these acoustic waves and some of their relations to formation properties of interest are also discussed. The more obvious potential uses of character logs are listed, and some suggestions are made regarding the requirements for a sufficient but practical character log for routine use. CHARACTER LOGS Some 10 years ago, Vogel' and Summers and Broding' noted that the signals received uphole from an acoustic logging tool located in a borehole had a number of interesting characteristics. The logging tool consisted of two or more pressure transducers spaced on an acoustically insulated body (Fig. la). One of the pressure transducers was used as a transmitter to generate pressure waves in the borehole fluid. The other transducer served as a receiver to detect any pressure waves reaching it in the borehole. The receiver then converted these pressure waves to electrical signals which were transmitted to the surface and displayed on an oscilloscope as a record of time vs receiver-signal amplitude. Fig. lb is a schematic representation of a typical record. The interesting characteristics seen in the earlier' and subsequent experiments were (1)

By Todd M. Ruff

Blind areas around construction equipment are a major contributing factor in incidents involving a piece of equipment striking a worker. In highway construction, these types of incidents result in an average of 22 deaths a year in the United States. The Spokane Research Laboratory of the National Institute for Occupational Safety and Health, in cooperation with the Washington State Department of Transportation, is evaluating methods to decrease these incidents. One such method uses devices that assist equipment operators in monitoring blind areas around the equipment to prevent collisions with workers or other objects. Several camera and sensor systems are available for this application. These systems were evaluated on various trucks used in road construction and maintenance. Tests were conducted on sanding trucks during the winter months, which allowed researchers to investigate the effectiveness and limitations of various technologies under the most extreme conditions. Tests were also conducted on dump trucks and utility vehicles during the warmer months to study the effectiveness of the systems in highway work zones. Results showed that many difficulties arise when using camera and sensor systems in cold, snowy climates. And, while the operation of these systems is more reliable during the warmer months, challenges still exist in using them on equipment in congested work areas.

By Rohrbach

Crosshole Sonic Logging (CSL) testing is commonly used to verify the integrity, quality and ultimately the acceptability of the concrete in structural elements such as drilled shaft foundations, secant pile cutoff walls, and secant/tangent pile earth retention structures. Besides concrete quality, many factors can impact CSL test results (e.g. laitance, air temperature, access tube spacing, access tube debonding, etc.). Effective use of CSL testing requires fully informed qualified practitioners capable of distinguishing between abnormal readings unrelated to deficiencies in the drilled shaft concrete and similar readings indicating the presence or possible presence of drilled shaft defects. Based on data and experience gathered from CSL testing of thousands of drilled shafts across North America, this paper discusses such factors and other information useful when evaluating CSL test results, and provides practical recommendations intended to reduce the potential for incorrect test data interpretation. The CSL testing industry is lacking in a clear, universally accepted guideline for the interpretation of CSL data and acceptance criteria of these concrete elements. This paper proposes terminology and a streamlined process for use when atypical results are obtained. The proposed terminology and method are intended to simplify and expedite the submittal review and approval process. Because construction activities for these elements are often on the project?s critical path, the benefits obtained in terms of project savings and reducing costly delays are undoubtedly valuable.

Several major impediments threaten the successful delivery of tunnel and under-ground construction projects. In addition to technical design and construction risks associated with tunnel projects, many of which are well understood, budgetary pressures, funding constraints and the complexity of procuring, administering and executing multiple concur-rent projects in a large program could also have a catastrophic impact on the program?s objectives. Contributing factors often include poorly managed design, procurement, construction, managerial, organizational, market and stake-holder risks, as well as nonconforming inputs or outputs to the costs and schedule, or any other potential inabilities to deliver the required or desired results. A strategy to prevent ?failure? of a project requires a proactive and holistic approach to risk management. Through planning, identification, analysis, management, monitoring and control of the project?s risks (both threats and opportunities), attention to management of risk will in-crease the probability and impact of positive events and decrease the probability and impact of events adverse to a project?s objectives.

By Pekka Taskinen

The converter-less nickel matte smelting technology (DON) adopted more than 20 years ago in Boliden Harjavalta smelter has been since that applied successfully to the processing of large number of nickel sulphide concentrates of various Ni-to-Cu ratios and MgO contents. The operational point of the technology is far from the conventional primary nickel smelting in the smelting-converting route. Therefore, a careful scouting of distribution equilibria of the base and trace elements in the smelting conditions of DON process has been conducted, in order to obtain quantitative information about the equilibria and thermodynamic properties of the nickel mattes at low iron concentrations, less than 10 wt% [Fe] in matte. The series of investigations has included novel experimental and analytical techniques for increasing the reliability and sensitivity of the phase equilibria as well as the element distribution observations carried out in typical high-grade nickel matte smelting conditions.

To the industrial geologist, as wen as to the general or historic geologist, the possession of a reliable key to the true order or sequence of the stratigraphy or position of the various upper rocky envelopes of the earth's crust, is, equally, a desideratum of the utmost importance. Of similar value to the two groups of students is the possession of facts which throw light upon the relationships which subsist between the puccessive rock formation of different countries, especially between countries lying close to each other, or within the same great geographical division.But there is necessarily a fundamental distinction which marks the respective limits of the field of observations of the industrial geologist, and the purely historic interest of the general geologist. The former has a more definite though less extensive scope. The scope of the latter is wide and indeterminate. In short, the observations of the industrial geologist are, 'from a commercial or economic point of view, of a more practical character, and are, therefore, intentionally restricted to the study of all geological questions which throw light upon the rocks which yield products of economic value and only include the study of the character and history of other rocks, in so far, as they afford aid to the more perfect comprehension of the best manner in which materials of economic value are likely to be sought, and the best means whereby these products may be secured for the material advantage of the community. The motive of the general geologist-in most cases-is a love of the study of some particular branch or province of the geological field, and the fascination of opening a new volume in nature's library, and the hope of extending the realm of knowledge, however slight, are often sufficient, as a motive, to enlist the energy and life's devotion of the true brethren of the hammer, irrespective of considerations regarding the commercial utility of the pursuit.

By J. P. Timmons, J. H. Moran, G. K. Miller, M. A. Coufleau

A prototype equipment has been designed and built for the digital recording of well logs on magnetic tape at the same time that the regular film recording is made. The format of the digital tape produced is such that it can be used directly at the input of the ZBM 704, 7090 or other models of ZBM computers which accept digital magnetic tape. This apparatus has been used for the experimental field recording of dipmeter tape logs which were subsequently computed by means of an ZBM 704 or 7090. In this paper the equipment and the digital tape are described briefly, and their application to the computer-interpretation of dipmeter data is discussed. A principal element in the interpretation of the dipmeter log is the correlation of the three microresirtivity dipmeter curves to determine the depth displacements between them. Several correlation methods for computer use are considered, with particular attention to their sensitivity to error and their consumption of computer time. The tape data were used to compute information content of the dipmeter microresistivity curves in terms of their frequency spectra. The results show that the sampling rate used in recording the digital information is quite adequate and illustrate a use of the digital tape in evaluating the characteristics of new tools. Some examples of field results are shown. It can be foreseen that, when digital tape recording becomes available for general field use, a whole new realm of possibilities will be opened up for the processing of other well logs through computations, which hitherto were not feasible because they were too laborious and time-con.sunzing. INTRODUCTION The last few years have seen a revolution in the design and production of data-processing equipment. Stored-pro-gram digital computers have progressed from a research curiosity to the basis of a major industry. There are now hundreds of such machines in daily use in the United States. With the acceptance of a technique that was, in fact, already clearly described by John von Neumann in 1945, the last decade has seen great strides in the development'of components, reliability, programming systems and, most spectacularly, in the sheer number of machines built and in use. In 1957 there were enough digital computers available to the oil industry to justify the suggestion that it would be worthwhile to investigate the possibility of using these machines in processing well log data.' The first result of this investigation was the appearance of what may be referred to as the input-output bottleneck. Well logs are customarily recorded on film. To get these data into a machine required then (and still does): a time-consuming semi-automatic reading of the film; conversion of the log data to digital form; and recording these digital data in some medium acceptable for computer input, such as cards, magnetic tape, or punched paper tape. However, the recording, reading, and re-recording could only result in deterioration of the data. Therefore, it was concluded that the fist step should be the development of a new, more direct recording technique supplemental to the film recording, which would provide easy access to the digital computer. There are many solutions to the problem of recording log data in an easily recoverable form. After careful consideration it was decided to adopt the boldest solution which, it was felt, was also the most elegant. It was decided to record well logs directly, in the field, on magnetic tape in such a way that this tape could be used without further modification as an input to the IBM 704 or 7090 computer. To realize practical field recording of magnetic tape logs, it became necessary to develop in a rather small package, an analog-to-digital converter, a tape recorder, and the necessary multiplexing and control circuits to allow the simultaneous recording of a multiplicity of logging signals. The magnetic tape recording was to be made simultaneously with the conventional logging operation in such a way as not to interfere with it. Along with the development of hardware, it was necessary to begin development of interpretation techniques and machine programs that would exploit the power of the digital computer. Here, again, there is a long list of possible applications. After much consideration it was decided to concentrate on the interpretation of the dipmeter log as a first application. It is the object of this paper to describe in some detail the developments sketched in the last three paragraphs.

By H. C. Johnson, J. K. Elliott

One of the primary requirements for successful operation of an enriched gas-drive project is to control the composition of injection gas. This can become a serious and difficult problem, particularly in cases where the enrichment material is being furnished from a number of field -produced gas streams. It is possible to effect control of the injection gas composition through frequent or continuous sampling; however, this can be extremely costly and, in many cases, impractical due to laboratory requirements of time. Another alternative would be to provide a calculation technique which would be flexible and sufficiently accurate to predict composition of the liquid and gas streams of interest at any point in the system. The purpose of this paper is to discuss a technique that was used successfully on an operating enriched gas-drive project for developing information which could be used for controlling composition of the injected gas. FIELD OPERATIONS The particular field (hereafter called Example field) in the example operation being discussed is composed of four oil reservoirs (A. B, C and E) and one gas condensate reservoir (D). Casinghead gas from the oil reservoirs and gas from the gas condensate reservoir are gathered through a field gathering system as shown in Fig. I for injection into Reservoir C. The gas mixture which is recovered from the five reservoirs for injection purposes is composed of gases liberated in 19 individual separators, each operating at a separate temperature and pressure. PROPOSED CALCULATION TECHNIQUE It is well known that vapor-liquid equilibrium calculations in general use throughout the petroleum industry can be used to predict reliably the phase behavior of hydrocarbon mixtures, particularly at pressures less than 1,000 psig. It is then a simple matter to account for the material on a ComPonent basis by m''ing flash and material balance calculations at each separation point in a hydrocarbon system. Accordingly, it was proposed to use vapor-liquid equilibrium and material balance cal- culations with a medium-sized electronic digital computer as a basis for developing a control procedure for use in controlling injection gas composition in the enriched gas-drive project. Although the approach is a simple one, the numerous vapor-liquid equilibrium calculations involved make the problem laborious; in this particular case, it would have been impractical to make sutficiently complete analysis without the aid of digital computing equipment. SAMPLING AND VERIFICATION OF CALCULATION PROCEDURE To obtain representative gas and liquid stream samples and to provide a quantitative measure of overall system Performance for comDarative purpLses, a thorough test of the field and plant system was conducted in the summer of 1957. Oil production at each battery was sta-

By A. B. Hildebrandt

P. B. Baxendell is to be complimented for an exccllent piece of work. To our knowledge there has been no previous publication of field data on the flow of oil and gas through the annulus of a well. It is certainly gratifying to see this work on annular flow confirm the previous published correlation procedure on tubing flow. It extends considerably the range under which reliable gas-lift calculations can be made. Baxendell discussed this work with us about a year ago and was kind enough to send a large scale plot of his correlation. We had been designing gas-lift installations on flow through the annulus, assuming that the original correlation of the f factor based on tubing flow' was valid as long as we stayed within the same mass velocity range on which the correlation was based. Doing this work necessitated the use of an equivalent diameter for the annular flow. The equivalent diameter is defined as area' of stream cross section wetted perimeter and for the case of an annulus is D, — D,. Substituting this in the basic equation correlating energy loss along with the area to flow required to convert the velocity, to volumetric flow rate, D (Baxendell's Eq. 7) becomes dell's expression, D,). Similarly, the D in 1.4737 X 10 (M&/D) becomes (D, + D;) for annular flow. On receipt of Baxendell's data, we. of course, recalculated it to put it into the form we were using, and to see how well it agreed with the correlation based on tubing flow. Fig. 1 shows the results, which were certainly gratifying. For low values of (D, - D,) pv, the data coincide with the data on flow through tubing, whereas at high values the data on flow through the annuli appear to be leveling off to a constant value. For very high rates of flow where the turbulence is very high, one might expect the value f to level out and become constant. A bulletin published in 1914 by the U. of Wisconsin presented results of a large number of laboratory teats in air lifting water through short lengths of 1.25-in. tubing. It was possible to correlate a random sampling of

By J. S. Hegwer, P. M. Dunlap

An improved acid for the treatrrzent of sulfate-con-raining limestones and dolomites is described. The acid is designed to reduce he reprecipitation of dissolved calcium sulfate and the possibility of plugging permeable flow channels. In addition, this improved acid has a much lower reaction rate than that of regular acid; the advantages of a "retarded" acid are obtainable. Field testing of the acid has shown it suitable for use in sulfate-containing formations. Substantial improvements in productivity generally resulted. INTRODUCTION Acid treatments of limestones, dolomites and other formations bearing carbonate deposits are frequently unsuccessful when the calcareous formation contains sulfate, either as anhydrite (CaSO,) or gypsum (CaSO4. 2H2O). Preliminary dissolution in acid followed by redeposition of calcium sulfate appears to be a major factor contributing to poor well performance after acidizing. The precipitate is usually the gypsum form of calcium sulfate, but in higher temperature formations it may be anhydrite. The freshly precipitated crystals are nearly always very small and needle-like. They may occupy a gross volume many times that of the original anhydrite crystals and will obviously constitute an impediment to flow through newly enlarged flow channels. It is believed that the redeposition problem is most severe when anhydrite lines the fracture systems and large pores which supply the effective permeability of a formation. Microscopic inclusions of calcium sulfate also present large sulfate surface areas for dissolution in acid. In either case, great amounts of calcium sulfate may dissolve before the acid can be spent on formation carbonates. For regular spent acid (originally 15 per cent hydrochloric acid) the precipitate could be as much as 270 Ib gypsum/1000 gal acid. Two techniques have been applied by the industry for reducing sulfate plugging during acidizing. The method'.' commonly employed in the field is the attempted removal of a quantity of regular treating acid before it has reacted completely with the formation. This is practiced because the solubility of calcium sulfate is greater in a solution that is still acidic than in one which has been largely spent on the formation rock. The chance of precipitative plugging is therefore reduced if the withdrawal is successful. However, it is often impossible to get the acid out of the formation before precipitation occurs. A second possible method, which at first glance appears practical, involves addition to the acid of sequestering agents which form strong soluble complexes with calcium ions. These chemicals do increase the "solubility" of calcium sulfate in fresh acid, but to a lesser extent in spent acid. The sequestering agents have, therefore, proved unsatisfactory because the amount of sulfate eventually deposited from the spent acid may be greater than that from regular acid. Another logical approach to the problem of calcium sulfate reprecipitation is the prevention of the initial dissolution of calcium sulfate by the common ion effect. This may be accomplished by adding a soluble calcium salt to the fresh acid. The use of calcium salts in treating acids is not entirely new. An earlier suggested use of a soluble calcium salt in hydrochloric acid apparently failed to recognize the full extent to which the solubility of calcium sulfate could be suppressed. The present study extends this earlier work and adds certain improvements toward the development of a practical anti-anhydrite acid. LABORATORY DEVELOPMENT Calcium Sulfate Solubility Table 1 shows the results of a laboratory study performed to establish the effect of calcium chloride concentration on gypsum solubility. Because of the strong tendency of calcium sulfate to form supersaturated solutions, accurate solubilities are difficult to determine. These solubility data probably are reliable to within ± 15 per cent. The solubility of calcium sulfate in 15 weight per cent hydrochloric acid increases with increasing temperature. This trend is also followed in hydrochloric acid which cantains calcium chloride. This is contrary to the solubility behavior of calcium sulfate in water, wherein the solubility decreases with increasing temperature.

By Zhi-xiang Cui

Effects of flux, vulcanizing agent and reductant on slag cleaning in new-type slag cleaning furnace (Φ3.6 × 8.1 m) were investigated under the conditions including smelting temperature of 1200 and 1250 °C, settling time of 30 and 60 min, and Fe/SiO2 of 1.7–1.9. The results show that addition of SiO2, B2O3 or CaF2 into original copper smelting slag can improve settling separation effect. Though no effect on copper recovery, addition of FeS can provide heat required by reaction with oxygen and reduce copper dissolution in spinel phase and slag. Copper content in discarded slag can be controlled at 0.26% under the optimum comprehensive conditions with ratio of oxygen to natural gas of 1.6.

By Paulo Couceiro

Highly non-ideal explosives usually tend to react expressively below their ideal detonation velocities. In these cases, dimensional effects and product heterogeneities become important to proper model the detonation state. Although Direct Numerical Simulation (DNS) techniques can provide a complete and exact solution for this problem, its actual computation cost is still not practical for industrial applications. In order to minimize these constrains, a simplified two-dimensional steady non-ideal detonation model for cylindrical stick explosives is developed. Based on an ellipsoidal shock shape approach, the proposed model uses the quasi-one dimensional theory for the axial flow solution and combine the post-shock sonic flow criteria with some limiting conditions for the explosives’ unconfined radius determination. Due to its attractive fitting capability for unconfined detonation experimental data, the model offers the possibility to predict the non-ideal detonation state for any diameter, resulting in a full mapping of the diameter-effect curve of the explosive. Thus, the proposed engineering approach is used to model the main properties of some of the most common ammonium nitrate-based explosives used in mining and quarrying industries, including the complete axial flow solution.

By Tuomas Hirsi

The world’s first large scale modular solvent extraction plants have been delivered by Outotec. The first of these is now in operation and has proven that the VSF®X technology can deliver the excellent performance of the Outotec VSF® solvent extraction process. Modular delivery allows site work to be minimized and the manufacturing done in a controlled environment, allowing for serial production manufacturing benefits. Container based delivery was found to be a highly efficient way of utilizing the standardized transportation methods on a global scale. Site work with modular units was found to be efficient and highly predictable. In this paper, we present the first successful Outotec VSF®X deliveries and discuss the benefits of the modular delivery and design compared to the standard solvent extraction installation’s delivery. The process performance of the VSF®X is also discussed with experiences from the first industrial reference presented.

By Clara Godoy, Paulo Couceiro, Juan Navarro

The continuous automatization and digitalization of the different stages involved in any underground construction bring new possibilities to optimize the operation. One of the most important requirements for the development of these projects consist of a proper rock mass characterization for optimizing the stages of the drilling, blasting and support cycle. In the last few years the road to digitalization has gone through data science and big data, showing the importance of data gathered to describe the geological and geotechnical environment that surrounds the operations. Since rock characteristics have an important influence in the drilling response, the technological advances in the sensorization of drilling machinery such as the Measurement While Drilling system (MWD) allow to gather the necessary amount of information to be applied in data science processes to evaluate changes in the rock mass with higher resolution than conventional methods. In this paper, Machine Learning techniques have been used to combine data monitored from the drill rigwith scanner profiles of the excavated sections to develop an automatic geotechnical rock mass characterization model able to estimate potential zones of over- or under-break of the remaining rock mass in underground blasting. By comparison of scanner profiles of the excavated sections with the blasthole positions, an Excavated Mean Distance (EMD) between the contour blastholes and the excavated profile has been obtained, which may be considered as damage measure. Considering blasting factors as constant, the model combines the rotary, percussive, hydraulic flushing and the rate of advance of the drilling, and the confinement of the rock mass by depth, to detect zones with different rock properties. This provide an early information of the rock mass condition around the blastholes and the prediction of expected overbreak generated after blasting, being possible to design more efficient bastings, in which each borehole is filled with the right and necessary explosive charge. The analysis comprises data from 57 blasts (around 1700 contour blastholes) and more than 4000 excavated sections.

By John Henry Harden

IN 1874, with Mr. H. Y. Attrill, of Baltimore, Md., I made an examination of some property at Goderich with reference to sinking for and mining salt. With this end in view we visited all the wells in the neighborhood, but the information sought being of so unreliable a character I advised the putting down of a borehole on the property. This has since been done, the result of which has lately been published by Dr. T. Sterry Hunt in the Toronto Globe. From this there appears to have been passed through six beds of salt of an aggregate thickness of 125 feet. Rock-salt was known to exist, for, by the boring of existing wells, small crystals had been brought to the surface in the dirt, but no attempt had before been made to obtain a reliable sample or to prove the number and thickness of the beds. The question now remaining for discussion is, shall the present method of obtaining the salt be continued, or shall the beds be won by a shaft in a regular mining fashion, by which means the salt may be gotten in a condition almost ready for the market? The present mode of obtaining salt is by boreholes from 6 inches to 8 inches in diameter drilled to the beds, into which is inserted a pump. The "feeders" of fresh water intersected in drilling the well are allowed to descend on the outside of the pump-tube to the salt beds and there become saturated, when, on use of the pump, brine is obtained for evaporation. In the beginning brine can only be had in limited quantity, but by the daily application of the pump, and the gradual solution of the salt, a larger surface becomes exposed to the action of the fresh water, and a continuons supply of brine is obtained. It will then be understood that the supply of brine is dependent upon the feeders of fresh water intersected in boring the well, which, we are told, have never shown any sign of diminution, and this is the water that must be encountered in sinking a shaft. There are ten wells in operation at Goderich, the most important one to the present project being known as the Hawley Well, located at an elevation a few feet above Lake Huron at the mouth of the river Maitland, at, a much lower level and nearer to the proposed shaft than any other well in the district. At this well the feeders

By C. Kathryn Sole

The close proximity of cobalt and nickel on the Periodic Table and their frequent occurrence together in nature means that their separation in primary hydrometallurgical flowsheets is not only often necessary, but requires the use of innovative chemistry to achieve high selectivity. Today, increasingly stringent demands for the high-purity cobalt and nickel salts required for battery applications in consumer electronics, electric vehicles, and solar applications are again challenging the state of the art. The evolution of cobalt–nickel separations is traced from the basic precipitation technologies employed in 1960s, through commissioning of the first cobalt solvent-extraction plant in South Africa in 1974, to the commercialisation of organophosphinic-acid extractants (which provided a step-change improvement in selectivity) and their eventual widespread use in the 1980s and ’90s. This was followed later by their sulphur analogue, which enabled different possibilities for laterite processing in the new millennium. Separations in chloride media, which take advantage of the different speciation chemistries, and nickel extraction by oximes in ammoniacal systems are also discussed. More recently, chelating and solvent-impregnated resins have added further dimensions to the possibilities for flowsheet design and enabled higher purity products to be attained from both primary and secondary sources. Selected case studies and flowsheets are described.