Search Documents

Operating Characteristics of Centrifugal Fans and Use of Fan Performance Curve Discussion of paper by. Louis W. HUBER, presented at the New York Meeting, 1926, .and issued, as Pamphlet No. 1542-A, with MINING AND METALLURGY, February, 1926. G. BRIGHT, Pittsburgh, Pa.-Apparently from the pressure curves for a forward-curved-blade fan, in Mr. Huber's paper, practically all ventilation-might be stopped with increased resistance. In order, to discuss the characteristics of a fan we need, some better way to measure the characteristics of a mine. You all know that. the average anemometer is not very-reliable. Sometimes two anemometers, supposed to be recently calibrated, will differ 50 per cent. Either this or some other committee should standardize measuring methods. The characteristic curves of fans, given by Mr. Huber, would indicate that the forward-curved-blade fan would cause trouble in attempting parallel operation, because two machines will not parallel unless they have dropping pressure characteristics. On the other hand, it is indicated that with the backward-curved blade, they could easily be paralleled. But few mines use more than one fan. Mr. Huber said that if the resistance of the mine was considerably more than contemplated, the quantity of air might be such that the efficiency of the backward-curved fan would be seriously affected, dropping say from 70 to 55 or 50 per cent. In such event, could a difference of speed be selected for the fan that would give the quantity desired at a higher efficiency? L. W. HUBER, Pittsburgh, Pa.-The backward-curved-blade fan responds to change in speed the same as any other fan; if' the speed is doubled, the quantity of air is doubled, the pressure is increased four times and the horsepower eight times. One point not mentioned in the paper is that the backward-curved fan is more efficient than the forward-curved or any other type. If the latter were more efficient, it would pay to install that type and keep the resistance of the mine constant, which is hard to do but it can be done with care. But the total mechanical efficiency of a fan with backward-curved blades is from 10 to 20 per cent. higher.

Jan 1, 1927

By E. D. Gardner

Open-cut mining of copper ores in the western United States is a relatively new industry. At first the mining methods were mainly adapted from those used at open-cut iron mines and at quarries, but now efficient practices that are more suitable for the copper deposits have been developed. The pioneer in this field is the Utah Copper Co., of Bingham, Utah, which deserves great credit for working out much of the early procedure. Stripping began at that mine in 1906, and the large Garfield concentrator was put in commission in 1908. Next in order of development were the Nevada Consolidated Copper Co., at Ely, Nev. ; the Chino mine of the Ray Consolidated Copper Co., at Santa Rita, N. Mex. ; the New Cornelia Copper Co., at Ajo, Ariz. ; the Sacramento Hill mine of the Copper Queen Branch, Phelps Dodge Corporation, at Bisbee, Ariz.; and the open cut of the United Verde Copper Co., at Jerome, Ariz. The Sacramento Hill mine began to produce in 1923, and the United Verde open-cut mine has produced ore mainly in connection with stripping. The writer visited the Utah Copper mine in September, 1923; the Nevada Consolidated in August, 1923; the Chino in July, 1924; and the New Cornelia, the Sacramento Hill, and the United Verde open cut at various times during 1922, 1923, 1924, and 1925, mostly in connection with other work.

Jan 1, 1927

By Norman L. Wimmler

Active placer mining in Alaska began near Juneau in 1880, but the first gold rush did not start until 1896; then the discovery of the Klondike brought gold seekers from all parts of the world. A few of the newcomers were experienced miners, but the majority knew nothing whatever of placer mining. Even those who were placer miners of much experience found entirely new conditions, notably frozen ground, that presented many difficult problems. As a result, numerous methods of mining and of thawing frozen ground were tried. From these trials the practice described in this bulletin has been developed. All known placer fields in Alaska have been mined to some extent, and some have been virtually exhausted. In most districts, however, there remain large quantities of low-grade gravel and also some small isolated areas of comparatively rich gravels which could not be successfully mined because of adverse physical conditions. These districts are now the scene of most placer mining, including dredging, hydraulicking, drifting, mechanical methods of open-cut mining, and ground sluicing (or booming) followed by " shoveling-in."

Jan 1, 1927

By Francis W. Gray

Introduction Extensive undersea coal-mining has developed on both the east and west coasts of Canada, and at this time some four million tons, or 25 per cent of the total output of Canadian coal, representing a pit-mouth value of $14,000,000 per annum, is coming from coal seams lying under the sea. Of the coal now being mined in Nova Scotia, 55 per cent comes from under the sea, and this proportion is likely to increase. The Province of Nova Scotia is at this date receiving in royalties paid upon coal ?removed from undersea areas a sum exceeding $400,000 per annum. The subject is, therefore, one of special interest to the Mining Society of Nova Scotia and the Canadian Institute of Mining & Metallurgy, and while this paper will deal chiefly with undersea coal-mining in Nova Scotia, an attempt has been made to summarize the development of mining practice in the winning of undersea coal in other parts of the world, with the hope that such a recital may assist in the assessment of local problems. The connection between the mining of coal under the sea and an insular or maritime geography is obvious in regard to Great Britain, Japan, Vancouver Island, Australia, and Cape Breton Island, and also in regard to the curious conformation of Chile; the tendency towards growth of a mercantile marine and naval eminence is equally obvious where coal is mined at tidewater. But, there is the further and less favourable significance that the mining of coal under the sea is associated with poverty rather than with abundance of coal reserves.

Jan 1, 1927

By Oliver Bowles

Lime is of tremendous importance to modern industries. In agriculture it is regarded as essential to the continued fertility of many important regions; in building it is indispensable, and in the many ramifications of the chemical industries it is so necessary and so widely employed that it has been designated "the king of all the bases." Figure 1 shows a general view of a modern lime plant producing more than 500 tons of lime daily. In 1924 the production of lime was reported from nearly every State in the Union and amounted to more than 4,000,000 tons, valued at, nearly $40,000,000. For a production of that magnitude between 8,000,000 and 9,000,000 tons of limestone are required. The many problems involved in winning this great quantity of raw material from the natural rock and preparing it for the kilns have in the past received little attention from any governmental agency. Therefore, in compliance with a request from representatives of the National Lime Association in 1922, the Bureau of Mines began a study of problems in limestone quarrying in an effort to advance more economical methods of operation and the utilization of waste material. Field studies were made at many quarries, and the information thus compiled, besides data already at hand from work in other branches of the stone industries, were disseminated to operators in the form of mimeographed Reports of Investigations, eight of which were issued at intervals during 1922, 1923, and 1924. A questionnaire was appended to each report, and quarry operators were invited to contribute additional information obtained as a result of their actual experience and observation. Operators of lime plants have been cordial in their responses and have supplied the bureau with much valuable information. From the data thus obtained, supplemented by later field studies, the revised reports have been combined to form the major part of this bulletin, which is believed fairly to represent present knowledge on the subject of quarrying limestone for lime manufacture.

Jan 1, 1927

By Robert S. Archer

THE proper material of construction for a given purpose is that material which meets the requirements satisfactorily at the lowest ultirnatc cost. It is consistent with this principle that most aluminum castings are made of an alloy containing about 8 per cent. copper. This alloy possesses mechanical properties satisfactory for general engineering purposes together with manufacturing characteristics leading to the production of finished castings at low cost. It is to the aluminum industry what gray iron is to the iron and steel industry. Just as some services require "semi-steel," malleable castings or steel castings instead of gray iron, there is a certain and growing demand for aluminum castings of superior strength or ductility, or both. Since the beginning of .the industry producers and others have sought to develop alloys or processes by which such castings could be made. Out of these efforts have emerged many alloy compositions and special processes, of which only a few have had sufficient merit to survive. It is the purpose of this paper to describe those which seem to the authors to offer the greatest promise for the production on a commercial scale of aluminum castings of superior mechanical properties, with special reference to heat-treated castings. The suitability of an alloy or process for actual manufacture is affected by so many factors that the problem of appraisal is not a simple one. Since this is such an important part of the whole subject it is proposed to discuss briefly some of the requirements. The final verdict is of course the result of commercial trial and experience. It will therefore, perhaps, be profitable to employ a somewhat historical method of treatment in discussing the subject of alloy development. The alloys or processes to be used in the production of aluminum castings are to be considered from the standpoint of their effects on both the utility and the cost of the finished casting. Specific gravity and mechanical properties come under the first head, while the properties

Jan 1, 1927

By W. R. Crane

Mining of the red iron ores of the Birmingham district, Alabama, has _gone on energetically for the past 50 years and has created a large iron and steel manufacturing center, the only important one in the South. The district produces about 10 per cent of all the iron ore mined in the United States and 80 per cent of the Alabama output is red ore ; moreover 43 of the 419 blast furnaces of the country are in the district tributary to Birmingham and produce 7 per cent of the pig-iron output. The rapid growth of the district has been made possible by investigations that have led to radical changes in furnace practice; studies of methods by which the low-grade, highsilica ores may be treated by concentration 1 will give still greater impetus to development. The· mode of occurrence of the ore has made mining practice comparatively simple, but with the rapid extension of the workings underground and the disturbed condition of the ore bed some distance from the outcrop, conditions tend to become more difficult. Stoping, handling, support, drainage, and ventilation are all affected, sometimes favorably and sometimes adversely, by the extended workings and increased depth of cover. Should beneficiatioil make available the high-silica ores of the lower bench of the Big Seam, mining practice must necessarily be adapted to the new conditions and will be rendered more difficult as the weight of cover increases at long distances from the outcrop. The support of workings will require more attention as the weight of cover increases, and the efficient and economical operation of the mines will depend largely upon improvements in mining and handling the ore.

Jan 1, 1927

By Maust. E. J., W. R. Crane

"IntroductionIn the study of mine drainage in the red iron ore mines of the Birmingham district of Alabama, an extensive series of measurements were made in order to determine the drainage from the area overlying and adjacent to the mines. Gaging rods were generally used in measuring streams, and weirs in ditches and sometimes as a check on rod work. These tests in turn were checked by current meter tests. In all, 725 separate stream gagings and 97 weir measurements were made. Certain relationships were worked out, particularly between rod and weir tests, which permitted obtaining results that are much more accurate 'under the existing conditions, than any available formula would give. The large number of weir measurements and the period covered by the tests made it impracticable to construct a weir for each observation so portable, adjustable weirs were built. The methods used are described here for the benefit of those interested in measurement of streams in connection with a study of mine drainage or otherwise. The Drainage AreaThe area draining the mining district lies between the crest of Red Mountain and Little Shades Creek, and for convenience was divided into sub-districts adjacent to certain groups of mines. Gaging stations were established on Little Shades Creek at the upper and lower boundaries of each sub-district, also at points on the tributaries near their junction with the creek. The difference between the volumes of water flowing in Little Shades Creek as it entered and left the sub-districts represents the flow from the tributaries on both sides of the creek. Since the flow coming from the sub-districts was measured direct, the inflow from the tributaries on the opposite side of the creek can be computed from the three volumes determined."

Oct 1, 1926

By E. C. Bennett

"INRTODUCTIONVarious methods of making leakage tests have been tried during a study of losses in the transmission of natural gas. This work has been carried on by the Bureau of Mines in cooperation with the Natural Gas Association of America. Results of torts show that the ""shut-in -pressure-drop"" method described by Rawlins is the most accurate and reliable; therefore its use is recommended. This paper describes a graphic method for computing the rote of leakage from the fall in pressure and change in temperature determined by the ""shut -in pressure-drop"" method of testing.METHOD OF MEASURING PRESSURE DROPThe gas is ""shut in"" line to be tested and is not allowed to escape except through existing leaks. The leakage causes the pressure in the line to fall. The charge in pressure is obtained with a dead weight gage. Approximate results may also be obtained from readings on a good spring test gage. Numerous tests show that the dead weight gage is more sensitive to small changes in pressure than spring gages.The temperature of the gas in the line is observed simultaneously with each pressure reading. Temperature changes affect the pressure exerted by a given quality of gas ""shut in a line, end since the rate of leakage from a closed system is directly proportional to the rate of pressure drop, fluctuations in temperature must be considered."

May 1, 1926

By H. A. Stacy

THE ability of galvanized sheet steel to withstand severe bending is of very great importance as relates to all such sheet material which, in service, is not used in the flat condition in which it is purchased. A "bend-test" clause is found in, all specifications for material of this kind. In the attempt to draw up a specification for galvanized sheet steel the subcommittee of the Federal Specifications Board having this work in charge, soon found that there was a surprising lack of published data and apparently very little available from manufacturing sources upon which to sustain or reject the various requirements embodied in the tentative specification which, in turn, had been based largely upon other specifications submitted to the subcommittee for this class of material. Specifications from 25 sources were received; 10 Government specifications, 10 from private users of such material, and five from manufacturers. The main points raised were: (1) The minimum mandrel thickness, expressed in terms of the thickness of the sheet tested, over which sheets with different weights of coating can be bent 180°, without serious damage to the coating; (2) the minimum radius of curvature on the inside of the angle in 90°-bends in such material; (3) effect of double seaming on the coating; (4) uniformity in the thickness of coating over a sheet, particularly as relates to the results of bend tests. In view of the uncertainty existing, it was considered very desirable for the subcommittee to conduct a series of tests in order to secure reliable information.

Jan 10, 1926

By Samuel Hoyt

THE hardness of annealed copper has been given in the literature and is easily obtained by any of the standard methods of hardness testing. It is not our intention to correct published values or to add to them, but to describe tests of two bars of annealed electrolytic copper in which the methods of Meyer's analysis were employed. MEYER'S ANALYSIS OF BALL INDENTATION TEST The ball indentation test is probably the most valuable hardness test we now have but, as it is carried out in the Brinell or Rockwell test, the result may be seriously in error without the operator suspecting such to be the case. This condition results from the isolated and uncontrolled nature of the measurement. The accuracy depends on the accuracy of the equipment and the care and skill used in the operations; there is nothing in the impression diameter, which is all that is measured, to indicate the presence of error. Meyer's analysis supplies a control of the measurements that goes far toward eliminating unsuspected errors. The principles of this work maybe obtained from elsewhere.1 As this subject has not received the attention of this Institute, it may be well to summarize the more important points as follows.

Jan 2, 1926

By F. E. Millett

The following notes deal chiefly with changes from steam to electric drives, or, in the case of the Bellevue pumps, from air to electric. Where electric power can be purchased or generated cheaply it can be used to advantage and is generally more economical than steam, especially in places remote from the central power-plant. Nothing could be more simple than the operation of electrical gear. It does not require a competent engineer constantly on the alert, oiling and watching bearings, and maintenance is at a minimum. The ease with which the current is transmitted from its source to where it must do its work is one of its greatest advantages. Transmission losses are very low. Generally speaking, the smaller the plant the lower the loss and 90 per cent, and better, efficiency is easily attained. In and around Bellevue 2300-volt, three-phase, is the standard distributing pressure; our power requirements and the distances transmitted, for the present, do not require more than this. Most of the heavier motors are 2300-volt .machines, which eliminates the cost and possible troubles of step-down transformers, and makes for a cheaper and less bulky motor. This applies to two fan, two hoist, and two compressor motors, the smallest being 75 and the largest 520 horse power. The standard pressure on power lines to all inside pumps is 550 volts, and 220 volts is general for the the tipple. While 110 volts is used for house and office lighting service, it is not economical around and in the mine. No matter what kind of device is used to lock and protect the lamps, they are invariably missing.

Jan 1, 1926

By E. O. Bennett

Various methods of making leakage tests have been tried during a study of losses in the transmission of natural gas. This work has been carried on by the Bureau of Mines in cooperation with the Natural Gas Association of America. Results of tests show that the "shut-in pressure-drop" method described by Rawlins2 is the most accurate and reliable; therefore its use is recommended. This paper describes a graphic method for computing the rate of leakage from the fall in pressure and change in temperature determined by the "shut-in pressure-drop" method of testing. METHOD OF MEASURING PRESSURE DROP The gas is "shut in" the line to be tested and is not allowed to escape except through existing leaks. The leakage causes the pressure in the line to fall. The change in pressure is obtained with a dead weight gage. Approximate results may also be obtained from readings on a good spring test gage. Numerous tests show that the dead weight gage is more sensitive to small changes in pressure than spring gages.

Jan 1, 1926

By Ben E. Lindsly

The recovery or partial recovery of the oil remaining in oil sands after the usual methods of production have become unprofitable is perhaps the greatest problem in the petroleum industry today. The amount of this oil remaining in the sand is variously estimated by those familiar with the subject to be 25 to 90 per cent of the original content.2 Lewis3 states, "The estimate of 80 to 90 per cent of the oil left underground does not seem incredible."

Jan 1, 1926

By E. E. Mueser

As Mr. Lundberg has already ably covered the theory of various methods of electrical prospecting, I shall confine my remarks to a consideration of the features which must obtain in an electrical prospecting method in order that it may be useful from a practical standpoint. These remarks I shall make with particular reference to the Elbof method. The successful application of all these methods rests, in the first place, upon the possibility of correlating theory, or empirically established facts, with the field data. Their practical usefulness, however, requires that the technique of making the field observations, and the procedure itself, be such that the method may be applied to large areas, under normal average conditions. The method, therefore, should not involve excessive preliminary labour costs to prepare the ground for actual prospecting work, nor should the prospecting work itself be so slow that its cost, when applied to extensive areas, becomes prohibitive. Moreover, it should be possible to apply the method even under difficult terrain conditions, such as rough topography and dense vegetation. It may be said of most of the methods referred to in the preceding paper, that, while they are interesting and theoretically sound, they fail to meet such practical requirements as I have outlined.

Jan 1, 1926

By E. L. Rawlins

The Bureau of Mines, with the cooperation of the Natural Gas Association of America, has conducted a study of leakage losses from natural-gas transmission lines. This study has shorn that surveys to determine the leakage from transmission lines lead to line repair work that not only aids in the conservation of gas, but can be made to show financial returns of large magnitude.2 In order to conduct the study, it was necessary to develop accurate and reliable methods of determining the actual leakage from pipe lines. METHODS OF TESTING Three methods that were developed and used to determine the leakage losses from high-pressure natural-gas transmission lines are: (1) The "pressure-drop" method, (2) The "metering-in and metering-out" method. (3) The "metering-in" method.

Jan 1, 1926

By J. C. Murray

Introductory: In dealing with a topic so large, one that involves such a multiplicity of details, and that also has certain controversial aspects, it is quite impracticable within the limits of this article to touch upon many most interesting phases and incidents. Also, to bring out the actual truth, it is necessary to make certain categorical statements. The writer believes that all such statements made here-under are supported by facts. Again, however, it is out of the question to cite all the proof. The writer, therefore, will gladly answer any pertinent criticisms or questions and thus supplement the unavoidable brevity of this paper. Controversial points will take care of themselves. Historical: For present purposes the history of gold mining in Nova Scotia may best be summed up in a very few paragraphs, in some of which the writer quotes freely from recent reports compiled by himself. The first material discovery of gold was made in the year 1860. As this and rapidly succeeding discoveries were looked upon as bonanzas, the claims were fixed at a size of 20 by 50 feet, and a yearly rental of $20 was charged. Later the claims (areas) were increased in size to 50 by 150 feet. In the year 1866 a temporarily successful company, so we are informed by a contemporary writer, owned a mill and mining plant worth $6,000. As this fact is cited with admiration, it is apparent that most of the mining and milling must have been done in a very primitive manner indeed.

Jan 1, 1926

Jan 1, 1926

By Paul D. Merica

This year of 1926 marks the 40th. anniversary of nickel mining in Canada. Although the first nickel mine of the Sudbury basin was discovered in 1883, it was not until 1886 that the Canadian Copper Company was organized and actually began to mine copper-nickel ore from the Lady McDonald, Stobie and Evans mines. The intervening years have witnessed some exceedingly interesting nickel history, particularly interesting and gratifying as well to Canadians. Forty years ago, at the inception of Canadian nickel mining, the world's consumption of that metal was about 1000 tons per annum and this was supplied largely from New Caledonia ores refined in France. This nickel was used principally for the production of nickel-silver, coinage alloys, and for nickel-plating. No processes were then known for refining the Sudbury ores nor for the separation of copper from nickel. Consequently, the pioneers in Canadian nickel mining faced the double problem of finding a method of treating their ores, and of finding a market for the nickel when and if they could extract it.

Jan 1, 1926

By Lewis C. Karrick

Although the Bureau of Mines has thus far made no large-scale experiments with oil shales, and the feasibility of the commercial manufacture of shale-oil products suited to present market requirements has not been demonstrated, there is ample reason to believe that these products will eventually supplement the more commonly used petroleum products and give equally good service. In 1919 the bureau, in cooperation with the Department of Metallurgical Research, University of Utah, began investigating the oil shales of the United States to obtain detailed information on their value. The States of Colorado and Indiana also cooperated through their State universities, in which research laboratories were organized to assist in carrying on the oil-shale studies planned and directed by the bureau. As a result of these studies much information is now available concerning laboratory methods of producing the greatest yields of the best products from oil shale. In order to study the principles that govern the retorting of oil shales and to test the oils produced, it has been necessary to develop and standardize reliable apparatus and methods for distilling shale, and to adapt to the testing of shale oils some of the methods the Bureau of Mines uses for testing petroleum. The methods employed by the Scottish shale-oil manufacturers were also studied, but most of them have been superseded by those described in this bulletin, which give more comprehensive and accurate results and employ more convenient apparatus. This paper is presented, therefore, as a manual of apparatus and methods that the bureau has developed for work on oil shale and found satisfactory for routine tests and for research. Explanation and discussion of the principles underlying the methods of testing are included wherever necessary for a clearer understanding.

Jan 1, 1926