Search Documents

By M. A. El-Sayed

"Double oxide films (bifilms) are significant defects in light alloy castings that occur when, during melt handling, the oxidized surface of the melt is folded over onto itself and then entrained into the liquid metal, encapsulating a portion of the local atmosphere. These defects create crevices in the final castings and have been shown to decrease tensile and fatigue properties, and also to increase their scatter, making casting properties unreproducible and unreliable. This paper reports on two different experiments performed to study the behaviour of such defects in Al alloys. In the first experiment and as a proxy for a bifilm, air bubbles were held in an Al-5Mg alloy melt for varying periods of time before the melt was allowed to solidify. The composition of the gas content of the bubbles was subsequently analysed using mass spectrometry to ascertain how it changed with time. In the other experiment the influence of the age of bifilms on the mechanical properties of Al-5Mg castings was assessed by holding castings in the liquid state for different times before solidification, followed by mechanical property testing and SEM and EDX studies of the fracture surfaces of tensile test bars. This research could provide a better understanding of the behaviour of double oxide film defects, and may lead to the development of new techniques by which these defects could be eliminated, or at least deactivated, in light alloy castings. Introduction One of the major structural defects affecting the reproducibility of mechanical properties of aluminium castings is the double oxide film defect (El-Sayed and Essa, 2017; El-Sayed and Ghazy, 2017). This type of defect is usually created as a result of poor filling system design. Owing to the very high reactivity of liquid Al-Mg alloy with oxygen in the air, the surface of the liquid metal can be considered to be permanently coated with an oxide film (Weigel and Fromm, 1990). As a consequence of surface turbulence, the oxidized metal surface can become folded over onto itself, but not fused, and then submerged into the bulk liquid, with a portion of the mould atmosphere being entrapped within it (Campbell, 2003; Al- Sayed, 2016; El-Sayed, Hassanin, and Essa, 2016)."

Nov 1, 2018

By J. Sepulveda

"Despite the recognized influence of product fineness on line capacity and downstream process performance, few mineral concentrators today use particle size measurement of the final product in automatic control applications for particle size. ‘Near-line’ particle size instrumentation has existed for decades and is utilized in modern concentrators, but low availability and measurement frequency, due to problems with slurry sampling and transport systems, make these technologies unreliable for use in automatic control. An innovative technology for real-time particle size measurement on individual hydrocyclones, named CYCLONEtrac™ PST (particle size tracking), has been developed by CiDRA Minerals Processing, and proven in commercial installations, demonstrating near 100% availability with minimal maintenance requirements, thus overcoming the limitations of previous technologies. Potential stakeholders require convincing, reliable information regarding the economic value delivered by automatic grind control projects. In this paper we present a methodology for estimating such value with the CYCLONEtrac™ PST technology, and demonstrate unique opportunities to improve process stability and performance. Based on actual plant data accumulated over time, the evaluation approach assesses and highlights the significant potential process improvement that can be expected with the particle size tracking technology. As an extension of previous work, in this paper we present the key operating criteria for optimizing the production of valuable metals and increase mill throughput by identifying the optimal grind size. As this requires operating closer to the process boundaries, accurate real-time particle size measurements, such as those provided by the CYCLONEtrac™ PST system, become essential for achieving the maximum potential value from every operation. For further illustration, data from three different copper plants is compared.Introduction Owners and operators of mineral concentrators constantly search for the most economically attractive way to increase the output of valuable metal. A logical approach is to identify a key parameter that has the greatest impact on the performance of multiple stages of the process and then use a holistic analysis methodology to determine how this key parameter can be controlled to optimize the final output.Particle size is widely recognized as such a key parameter; however, very few concentrators today use real-time particle size measurements for automatic control of the final product size due, to a large extent, to the inherent limitations of existing technologies. ‘Near-line’ particle size measurement instrumentation, which has been used for decades, typically suffers from low availability because the fundamental measurement technologies were developed for other, less demanding industries and then adapted to the harsh environment of the typical mineral concentration process. An outline of the key differences among the available technologies used for particle size measurement in comminution circuits has been completed in previous work, and plant data has proven the benefits of measurements on individual cyclones – something that, until now, has not been possible (Cirulis, 2017)."

Nov 1, 2018

By A. Tosun

"The size distribution of the muckpile formed as a result of open pit blasting operations has a considerable effect on the efficiency of loading, hauling, and crushing. Various researchers have developed specialized computer software that uses image analysis methods for determining the size distribution of the muckpile. However, these methods have some limitations. One of the most important of these limitations is that the very fine fragments in the muckpile cannot be used in the size distribution calculation. In this study, 18 test blasts in total were carried out in two limestone quarries belonging to Batiçim Corp. in Izmir, Turkey. A new model was developed in order to ensure that very fine fragments are used in the size distribution calculation. The size distributions of the test blasts were calculated by both the Wipfrag computer program and the new model. Correlations were established between the muckpile size distributions determined by both methods and the parameters determining the efficiency of the loader. IntroductionThe size distribution of the muckpile formed as a result of open pit blasting operations has a considerable effect on the efficiency of loading, hauling, and crushing. Various researchers have established certain correlations for predicting the efficiency of the operations according to the muckpile size distribution so that production can be carried out economically (Tunstall and Bearman, 1997; Nielsen and Kristiansen, 1996; Workman and Eloranta, 2004; Michaud and Blanchet, 1996; Frimpong, Kabongo, and Davies, 1996; Osanloo and Hekmat, 2005; Molotilov et al., 2010). In these studies, the 50% passing size (X50) is generally used. These methods rely on the correct measurement of the size distribution of the muckpile formed by the blast. The most reliable measurement method would be to subject the entire muckpile to a sieve analysis, but this is obviously impracticable. Therefore, computational method based on image analysis have been developed. These include IPACS (Dahlhielm, 1996), Tucips (Havermann and Vogt, 1996), Fragscan (Schleifer and Tessier, 1996), Cias (Downs and Kettunen, 1996), GoldSize (Kleine annd Cameron, 1996), Wipfrag (Maerz, Palangio, and Franklin, 1996), Split Desktop (Kemeny, 1994), PowerSieve (Chung and Noy, 1996), and Fragalyst (Raina et al., 2002). In these methods, the size limits of the fragments forming the material are determined by image analysis on photographs of the muckpile. However, the computer software has some limitations. It does not take into account the third dimension of the muckpile, nor the size distribution of very fine fragments. In particular, the fragment size ranges below 2.5 to 3 cm cannot be determined, and therefore these cannot be included in the muckpile size distribution. However, the muckpile formed by a bench blast contains a wide range of particle sizes (Tosun et al., 2015)."

Oct 1, 2018

By S H. Algie, E J. Knoblauch, I A. Lovatt, S G. Doig

Mill operating teams are expected to engage in a perpetual quest for process improvement – pushing the boundaries of practical process limits and testing new technology to achieve the next step-change in plant performance. Often the barrier to improvement lies in gaining management approval for process changes.Getting approval for investment in novel technology carries an added degree of difficulty, particularly in risk-averse operations, when it challenges conventional wisdom. A case in point is a new technology for controlling variability in slurry distribution. There is a widely held view that less-than-specified classification efficiency and spraying and roping of individual units in a hydrocyclone cluster, must be accepted as unavoidable. That these are wholly correctable deficiencies resulting from unequal loading of the individual units seems a bold claim. Wouldn’t the high turbulence of pumped slurries overcome all potential for segregation of solids? This paper discusses how the task of developing confidence in a new technology can be approached by a combination of physical modelling at small scale, and full-scale operating experience. Proving efficacy then leads to the next task: demonstrating value. Again, the particular technology serves as an example that could be of value to others developing relatively low-cost technologies. A high-pay-off as an investment may be achieved with improvements in metallurgical performance that are small in relation to normal process variations. This has led to an exploration of how process simulation modelling could be used, in conjunction with production data, to provide a benchmark for the expected change, which could be expressed in monetary terms.The next goal, which is currently being achieved in operating plants, is to realise the greater value now available through the optimisation of cyclone configuration, which becomes practical when the confounding effects of cluster instability are removed through equal loading.CITATION:Doig, S G, Algie, S H, Lovatt, I A and Knoblauch, E J, 2018. Investing in new process improvement technology: reducing the risk of implementation – a way forward, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 571–584 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By M Yahyaei, M S. Powell

Mineral processing plants have become large and complex, generally through progressive expansions. Addition of a pre-crushing stage to conventional Semi-Autogenous-Grinding (SAG) and ball mill - crushing (SABC) circuits has introduced a complex materials handling system coping with +200 mm particles. Application of High Pressure Grinding Rolls (HPGRs) and implementing hybrid comminution circuits (ie, HPGR-SAG mill) requires proactive control of the feed size distribution to each unit. Application of Vertical Tower Mills (VTMs) and other fine grinding equipment to achieve a finer grind size, while maintaining the throughput, requires splitting the feed evenly between parallel units. Many of the conventional comminution circuits (ie, staged crushing and screening followed by staged ball milling) must deal with the transition from open pit ore, which is generally altered and soft, to underground ore, which is intact and hard, requiring existing crushers to produce a finer product to unload the ball mills.This paper presents common process improvement opportunities which have been identified during a number plant process reviews conducted by the authors in Australian and international operations. The operation of comminution circuits to known and accepted standards, which is explained in this paper, could improve the performance of circuits by between 5 and 10 per cent, generally at no capital cost and often at a lower operating cost. The performance improvement can be realised as throughput increase, a finer product size, or reduced operating costs (ie, energy saving, low maintenance, less consumables).Process optimisation opportunities presented in this paper include: enhancing materials handling and storage to avoid segregation; standard operation of screens to reduce misplaced materials; proper feeding arrangement and control of crushers to increase their utilisation; preparing proper feed for SAG mills to reduce grind size; splitting the feed evenly between parallel equipment to improve utilisation, and controlling operation of classification units to improve energy utilisation.CITATION:Yahyaei, M and Powell, M S, 2018. Production improvement opportunities in comminution circuits, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 233–248 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By H Law, M Muller

Mount Isa Mines (MIM) Copper Concentrator currently utilises Agitair 120 banks for its roughing flotation circuit. Apart from a rotor change, the only other significant work completed to the Agitair banks since their installation and commissioning over 40 years ago has been a like for like refurbishment in 2016. The Agitair banks at the MIM Copper Concentrator currently utilise the Pipsa rotor design which progressively replaced the original Chile X rotor design in the 1980’s and 90’s in the copper concentrator. Since the development of the Pipsa rotors, modern rotors such as the Dorr-Oliver (DO) high shear rotors have been released to the market with proven recovery and concentrate grade improvements over previous rotor designs. This paper aims to detail the installation, testing and comparison of Pipsa versus Dorr-Oliver rotors in two different flotation sections of the MIM Copper Concentrator.CITATION:Muller, M and Law, H, 2018. High shear rotor trials in the Mount Isa Mines Copper Concentrator, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 393–402 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By R Tooher, S J. Oliver

The operation of copper flotation circuit is a challenging task for the site metallurgists and plant operators. To optimise the performance requires meeting both grade and recovery objectives. These plants have numerous pieces of equipment that are monitored by hundreds of sensors. The challenge is to review these sensors and adjust the numerous control inputs to maintain peak operational efficiency for extended periods. There is also a need to respond to equipment failure. These challenges lead to in operational inefficiencies and can result in a reduction in revenue.This paper details an overview of an operational assistance tool implemented at Newcrest's Telfer plant’s copper flotation circuit. This tool is based on a digital twin of the plant. A digital twin is a model of the plant that is simulated in parallel to the normal plant operation. It is fed with the plant data in real time to provide a prediction of plant operation. The model outputs directly generate the metrics that are used to assess the plant performance, and these are compared with the metrics calculated from the actual plant’s operation. Deviations between the model estimate and the plant’s actual performance are used to gather insight into plant health and alert the operator to poor performance. The operators gather more information regarding the root cause by reviewing the model’s inputs that have deviated outside their normal operating range. An evaluation of the plant performance, following the commissioning of the digital twin, showed an overall reduction of acid soluble copper in the tails.This paper discusses the implementation of a digital twin of the plant to monitor plant performance during live operation. It will include details on data collection and cleansing, data reduction techniques, model development, and real-time implementation. The results of the case study of an implementation of a digital twin at Newcrest's Telfer copper flotation plant will be used throughout the paper.CITATION:Oliver, S J and Tooher, R, 2018. Optimising flotation plant operation by using a digital twin in the control room, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 93–100 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By A Roudnev, P Loderer

Mineral froth pumping utilising centrifugal slurry pumps is a major engineering challenge for both the end users and pump manufacturers. The traditional approach has been to oversize the pump for pumping mineral froth. New horizontal slurry froth pump designs offer opportunities to improve froth pumping capability of mineral froth with challenging (high) Froth Volume Factor while maintaining high efficiency, long wear life and stable pumping performance.CITATION:Loderer, P and Roudnev, A, 2018. A reliable solution for pumping mineral froth with challenging froth volume, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 291–296 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By M J. Thurley, L Lindqvist, D Degerfeldt, J Nyström, R Nordenskjöld

Rock breakage is a major component of all mining and mineral processing operations with the particle size distribution linked to productivity through the comminution chain. Optimisation and automatic control of comminution, material handling, and agglomeration processes is a complex task with large potential for gains in productivity, and energy efficiency. A key factor in realising these gains is the requirement for fully-automated online particle size distribution measurement to provide the necessary feedback and input for control. Moreover, to enable automatic control system it is necessary to provide a consistent, reliable size distribution measurement that avoids the significant errors resulting from under-sizing overlapped particles and over-sizing clusters of fine particles. Published literature and observation of commercial systems indicate a body of predominantly 2D photographic based particle size measurement systems that suffer from a number of significant errors except in the simplest case of a monolayer of particles under good illumination with limited colour variation in the material. In order to overcome these limitations a university and industry collaboration developed three-dimensional particle measurement (3DPM) between 2006 and 2012, based on 3D surface profile measurement of the visible material on conveyor. 3DPM avoids particle delineation errors due to variation in material colour and shadows, detects overlapping versus non-overlapping particles, and identifies areas of fine particles as fines and not large rocks. 3DPM measures: the visible material and calculates its particle size distribution, bulk volume, detects boulders, and conveyor belt fill factor in an automated consistent manner. Furthermore, 3DPM’s advanced algorithms allow observation of particle variation that would otherwise be undetected without the capacity to identify visible areas-of-fines and overlapped particles. Boliden Mines has installed 3DPM at three operations for measurement between the stockpile silo and grinding mill, and measurement after the primary crusher. Fragmentation measurements across multiple years of measurement are presented with some observations of plant behaviour. In the future 3DPM results will be incorporated into automatic control strategies for plant optimisation. 3DPM is used across a wide range of material types and applications that also includes; limestone aggregate for quality control in manufacturing, agglomerates for closed-loop automatic control in chemical production, and measurement of coke for size-based blending feed control to the blast furnace in steel production. CITATION:Thurley, M J, Degerfeldt, D, Nyström, J, Nordenskjöld, R and Lindqvist, L, 2018. Automated, online measurement of bulk material size distribution on conveyor using 3D profile imaging at Boliden Mines, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 641–652 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By J Seppelt, B Akerstrom, A Rice, J Bubnich, T Waters

The Concentrator 1 plant at Cadia transitioned from Cadia Hill open pit to the Cadia East block cave ore body in 2013. As a result of this change, major plant upgrades were required to achieve the desired throughput while treating more competent ore. The 40-foot (40’) SAG mill now receives a feed of predominantly high pressure grinding rolls (HPGR) product with a minor component of secondary crushed ore at a combined F80 of 17 mm. The significant reduction in feed size to the SAG mill has markedly changed the operating characteristics of the mill, which has been extensively studied since commissioning in 1998.This paper examines the operation of the 40’ SAG mill in its new configuration in the Concentrator 1 circuit. Operational stability is highlighted as a significant factor in delivering mill performance, which has been achieved through several key improvement projects utilising a theory of constraints framework. Five years of successful project implementation has progressively lifted the maximum processing rate of Concentrator 1 from the design estimate of 2455 t/h to above 3000 t/h. CITATION:Waters, T, Rice, A, Seppelt, J, Bubnich, J and Akerstrom, B, 2018. The evolution of the Cadia 40-foot SAG mill to treat the Cadia East orebody: a case study of incremental change leading to operational stability, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 217–232 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By J J. Cilliers, K Hadler

Air is fundamental to flotation; not only is it required to collect the valuable particles, but it also controls the froth stability and consequently the separation performance for a given feed. Froth stability can be described and quantified in numerous ways, which are subtly different. Air recovery is one such measure of froth stability which accounts for both the stability of the bubbles and the mobility of the froth. The benefit of using air recovery as a measure of froth stability is that it exhibits a peak as air flow rate is increased, and this corresponds to the air rate at which the optimal separation performance is obtained. As such, it provides a single target value for optimising air flowrate for a given set of feed conditions. Use of air recovery, however, has one potential drawback: accurate measurement of the inlet air flow rate to a flotation cell is required. This can be problematic for operations, particularly where calibration of air flow rate is carried out infrequently or where there is no air flow rate measurement, such as for many self-aerated flotation cells. To this end, we present an alternative method for determining the peak in air recovery (PAR) air rate.We introduce a simplified method for determining the PAR air rate using trends in froth velocity and overflowing froth height, both of which are readily measured using existing froth image analysis systems. We will show, using industrial data, the application of this simple technique to find the optimal air flowrate for flotation cells. We will also discuss other alternative techniques for air rate optimisation that have the potential to improve separation performance using existing technology.CITATION:Hadler, K and Cilliers, J J, 2018. How to find the optimum air rate for flotation cells, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 377–384 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By M Thompson, N Vines, Z Hearne, S Lam, G A. Gomes-Sebastiaõ, D van der Spuy

Construction and commissioning of the Nova Copper-Nickel project of Independence Group was completed in late 2016. The plant is in the Fraser Range of Western Australia, about 120km east of Norseman and produces separate Copper and Nickel concentrates. Since the early feasibility phases of the project, the importance of automation and control was recognised and planned for to ensure the plant performance meets the design expectations. The site is well equipped with common as well as advanced instrumentation. It currently boasts the largest number of Blue Cube MQi (mineral quantifier inline) slurry grade analysers on a single plant worldwide. It was also decided that 25 Blue Cube TempoTracks would be installed on the flotation cells. The TempoTracks provide information on froth height and velocity, hence giving continuous, quantitative measurements of the froth that is pulled off each cell, rather than relying on infrequent, subjective visual inspections.The Nova concentrator consists of a differential flotation circuit whereby copper bearing mineral are selectively floated prior to nickel flotation. It is imperative that losses of copper to the nickel circuit, and vice versa, are minimised. The plant metallurgical team and Process IQ collaborated to develop and implement the advanced control strategy for the plant. This paper focusses on the optimisation of the copper concentrate that is pulled off the copper rougher and scavengers. This strategy was made possible by the additional measurements listed above. The control optimisation of the copper rougher and copper rougher scavenger circuit was implemented during August 2017 on the StarCSTM advanced control platform. It continuously optimises the level and air setpoints. The control philosophy incorporates several notable techniques which include: a variable mass pull target that is a function of the quantity and grade of material entering the circuit, integrated compensation to prevent inventory build-up in cells, balancing of the froth velocity over the lip of each cell to adaptive, modular system usage and advanced error handling. CITATION:Gomes-Sebastiaõ, G A, Hearne, Z, Lam, S, van der Spuy, D, Thompson, M and Vines, N, 2018. Nova copper-nickel project optimisation of the copper rougher-scavenger circuit through advanced measurement and control, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 77–92 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By J Young, S Yu, P Moyo, M Powell, A Musunuri, B Bonfils, S Kanchibotla, P Yaroshak, V Jokovic

The appropriate design of liners continues to be an issue on many mills worldwide. Loss of milling capacity especially at liner change, uneven wear lives along the mill, substantial scrap on worn liners, excess mill down-time, undesirably short and unreliable wear lives are all common issues. This paper presents a designed approach to liner optimisation that follows a logical path of initial design and step-wise improvements based on liner wear monitoring. The target is to have a good liner design from start-up, then tune the profiles, heights and thicknesses based on wear monitoring. This is conducted as a team of liner specialist, site personnel and liner supplier. The application to the Pustynnoye SAG mill of JSC Altynalmas in Kazakhstan is presented. The increase in liner life by around 50% along with increased mill throughput of over 20% illustrate the huge benefit of the cooperative triumvirate approach through the gains that can be made in productivity and reduced liner costs.CITATION:Powell, M, Kanchibotla, S, Jokovic, V, Hilden, M, Bonfils, B, Musunuri, A, Moyo, P, Yu, S, Young, J, Yaroshak, P, Yalcin, E and Gorain, B, 2018. Advanced mine to mill application at the Barrick Cortez mine, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 177–196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By A L. Randriamanjatosoa, G Small, C Greet

In flotation simulation models, the effects of pulp chemistry other than pH are often ignored and reduced to particles hydrophobicity or contact angle, neither of which can be measured readily in real time in an operating plant. The flotation response of a given sulphide mineral is known to be influenced and can be improved by changing the chemical characteristics of the pulp during grinding and flotation. The on-line measurement of pulp pH, potential, dissolved oxygen, temperature and oxygen demand of a process stream was completed with the PCM® (Pulp Chemistry Monitor) developed by Magotteaux in this study. The data generated together with relevant plant operating parameters were used to construct an empirical model and simulate the metallurgical performance of the ore. The same approach was also applied to laboratory flotation tests data using various grinding media types. The flotation models better fit the actual data when the chemistry of the pulp is taken into account.CITATION:Randriamanjatosoa, A L, Greet, C and Small, G, 2018. Effects of pulp chemistry on plant and laboratory flotation modelling, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 423–432 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By R Bose, M Bovell, G Cheong

Grinding media is a major consumable in mineral processing and therefore decreasing costs associated with its consumption is regularly considered a key goal for the minerals processing industry. Grinding media manufacturers have historically developed steels with improved wear life for their products as a way of delivering incremental media quality improvement. This has included increasing carbon levels from low-to-medium carbon steels up to the eutectoid carbon composition of 0.77% where the relationship between higher carbon and better wear performance is well understood. Producers today will regularly use grades in excess of 0.8% to further improve wear performance particularly for rolled grinding media.This paper first introduces the demonstrated relationship between this increased carbon content and improved wear resistance along with metallurgical rationale behind the high carbon production process and limitations. To test the performance improvement associated with the higher carbon steel grade, a series of Marked Ball Wear Tests (MBWT) were carried out. This paper also explores the relationship between ball properties, test methodology and wear performance and concludes by correlating increased carbon grade with a reduced consumption rate of between 3.1% and 6.1% in the tests conducted.CITATION:Bovell, M, Bose, R and Cheong, G, 2018. Improved forged grinding media performance with carbon content greater than 1.0%, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 559–570 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By G R. Ballantyne, V Souto, K Bartram

Particle sorting allows partially liberated minerals to be separated prior to energy intensive fine grinding. Sensors select particles for separation and air, water or mechanical ejectors are used to physically deflect those selected. To achieve effective separation there has to be sufficient liberation, accurate detection and presentation of a separated monolayer of particles. These three physical constraints determine the particle size limits, the sorting technology utilised, the separation efficiency, and the throughput that can be achieved. The combination of all these factors controls the effective limits on the degree to which sorting can reduce the specific comminution requirements and increasing energy efficiency. This paper will explore two case studies: the application of sorting in base metal mining and precious metal mining.CITATION:Ballantyne, G R, Hilden, M, Bartram, K and Souto, V, 2018. Characterising energy efficiency of particle sorting, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 531–540 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By J Geronimo, P Kumar, Z Yussupova, M Yahyaei, M Powell

This work goes beyond the general perception of how the well-known mine to mill process can be applied, by applying deeper knowledge along the mining chain. Grade deportment and dilution are considered at the mining stage, and modelled with the new SMI blast movement simulator, linking with the block model data. Assessing the shift to a considerably more competent section of the orebody is quantified via substantial milling trials at standard and higher-intensity blasts. These were stockpiled for batch processing through the mill to ensure feed integrity. The trial work included operating the mill at widely different fillings to develop Grindcurve milling responses. Additionally, model informed process control is initiated via a mill prediction tool.It has been found that accounting for blast movement for the higher intensity blasts could generate additional value of around $1.5M per blast. With the high-intensity blast and changing mill control, the plant was easily able to exceed projected mill throughputs with the far more competent Pipeline ore. Strategies to shift the workload and debottleneck the milling circuit were proposed and proven during the milling trials, demonstrating an increase in throughput of 7 per cent despite running at a lower SAG mill speed, and potential of 16 per cent for increasing the SAG mill to standard operating speed. A number of process improvement opportunities have been identified to enhance current productivity and ensure long term capability to process the considerably more competent future ores. All of this is being linked in with the major digitisation program at the Barrick Cortez site, with an objective of linking all the data into a mine-wide process optimisation system, that can embed the processes by providing process-wide data access and production support via the future dynamic models linking ore body knowledge to productivity along the full process chain.CITATION:Powell, M, Yahyaei, M, Geronimo, J, Yussupova, Z and Kumar, P, 2018. The designed approach to mill liner optimisation – experience at Pustynnoye mine, Kazakhstan, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 595–612 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By M Randall, P Ebzery, F Burns, C Aisthorpe, P Blanz

SAG Mill process control classically maintains the SAG mill volumetric filling within a set operating range. Typically a SAG mill weight measurement, by either bearing pressure transducers or load cells, is used as an inferred measurement of volumetric filling. To maintain volumetric filling within a set operating range the SAG weight setpoint use for process control requires regular review due to changes in SAG mill charge density (rock:ball ratio) and the wearing of mill liners. At Lihir Gold Mine in Papua New Guinea, the use of SAG mill weight for process control is additionally complicated by compromised load cells and drifting bearing pressure measurements. The need for an improved method of measuring and controlling volumetric filling led to the recent installation of the Outotec MillSense, a SAG mill toe angle instrument. This paper presents the integration of the toe angle control in to the Lihir SAG mill process control philosophy as replacement for the traditional mill weight control.CITATION:Burns, F, Aisthorpe, C, Blanz, P, Randall, M and Ebzery, P, 2018. Toe angle measurement for SAG mill control at Lihir gold mine, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 59–76 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By A Price, D Okle, K Brooks

The operation of flotation plants has been improved over the years by use of fundamentally based design techniques, a better understanding of reagent chemistry, online metal analysis and the use of digital control systems. However, optimal operation of flotation banks is not consistently achieved using manual operation. The reason for this is that the system is a highly interacting one, with changes in air addition, cell interface level and reagent dosages all being available, without it necessarily being clear as to which change should be made for a particular situation.This situation is made more complex by the fact that the feed to a flotation bank can vary in flowrate, composition and density over a fairly short period of time. It is not possible for a human operator to reject these disturbances, given the extent of the operation that is typically being monitored.Model predictive control (MPC) is a control and optimisation technique, developed in the oil refining industry, that aims to manage just such interacting multiple input multiple output (MIMO) systems. This technology makes use of linear dynamic models of the plant, that are experimentally derived. These models are then used in a receding horizon strategy to determine an optimal trajectory of the inputs to the system.MPC has been applied to four areas of the lead zinc flotation unit at Mount Isa mines. A total of 31 cells are being controlled by the system, which varies air to the cells, levels and reagent addition on a minute-by minute basis. The MPC controls concentrate and tail grades, reagent dosages, as well as recoveries to ranges set by the plant metallurgists.The development of the MPCs is discussed, together with the benefits realised. The key factors in insuring an ongoing return on investment are described.CITATION:Price, A, Okle, D and Brooks, K, 2018. Glencore Mount Isa lead zinc flotation circuit – experiences from the implementation of model predictive control, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 101–110 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By L Mikhael Gurieff, D Baas

The Phu Kham Copper-Gold Operation (Phu Kham Operation) is located in the Lao People's Democratic Republic and is owned and operated by the Lao-registered company, Phu Bia Mining Limited (PBM). Australian-headquartered copper and gold producer, PanAust Limited holds a 90 per cent interest in PBM; the Government of Laos owns the remaining 10 per cent. The Phu Kham Operation was commissioned in 2008 with an initial concentrator nameplate throughput of 12 million tonnes per annum (Mt/a). Subsequent improvement projects, including the Phu Kham Upgrade Project (PKU), completed in 2012, and the Phu Kham Increased Recovery Project (IRP), completed in 2013, increased the design throughput to 18 Mt/yr. In 2016, the actual mill throughput exceeded 19 Mt/a, this throughput is budgeted to be maintained until the end of 2020.The concentrator flotation circuit upgrade, completed during the IRP, called for a non-selective bulk sulphide concentrate to be generated from the rougher circuit. This in turn caused the mechanical flotation cells in the cleaner circuit, particularly those in the second cleaner bank, to become volumetrically overload. The overload reduced the cleaner circuit performance to approximately 92 per cent copper recovery at a 23 per cent copper concentrate grade, below the expected 95 per cent recovery. This bottleneck restricted copper units entering the plant to approximately 14.5 tonnes per hour (t/h) due to uncontrolled recirculating load build-up in the mechanical cleaning circuit.Maintaining the operating methodologies would have led to a copper production shortfall beyond 2016, to address this shortfall the Phu Kham Operation looked to optimise the Jameson Cell and mechanical cleaner circuit performance. The work included fundamental application of flotation practice and modelling, mineralogical analysis, bubble size analysis, plant surveys and test work. The results were used to develop and implement an innovative automated control system strategy incorporating flotation theory and operating strategies. The automation has the ability to quickly adapt to disturbances in the circuit and maintain optimised performance with little or no intervention by flotation operators.Upon completion, cleaner recovery increased to 95 per cent at a final concentrate grade of 23 per cent copper, and copper units entering the plant increased to 17.5 t/h.CITATION:Baas, D and Mikhael Gurieff, L, 2018. Developing flotation circuit control and automation for the Phu Kham Copper-Gold Operation concentrator, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 37–58 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018