Search Documents

By M I. Pownceby, W J. Bruckard

A South African chromite sample was subjected to characterisation and physical beneficiation testwork in order to assess its suitability to produce an upgraded chromite product with a silica level of <1 per cent SiO2 and a chromite level of >46 per cent Cr2O3. Chemical analysis by XRF indicated that the bulk material had a Cr2O3 content of 40.5 per cent w/w and a SiO2 content of 7.5 per cent w/w. Combined XRF analysis with sizing data showed that the majority (~70 per cent) of the siliceous material was present in the +600 ¦m fraction while ~70 per cent of the Cr2O3 was in the -600 ¦m fraction. Qualitative mineral phase analysis by XRD indicated that the sample mineralogy was dominated by ferrian-magnesiochromite spinel ([Fe,Mg]Cr2O4) and aluminium-chromite spinel (Fe[Al,Cr]2O4), with enstatite (Mg2Si2O6), haematite (Fe2O3) and anorthite (CaAl2Si2O8) as minor phases. SEM and EMP characterisation showed that the silica was mainly present in discrete enstatite grains but lesser amounts were also present as the high silica phases plagioclase and enstatite on the edge of grains. Wet gravity separation performed on sized fractions (-600+106 ¦m size range) from the -2.0 mm (primary) ore as well as the ore that had been crushed to pass 0.6 mm (secondary) showed that stage crushing of the -2 mm +600 ¦m fraction followed by wet gravity separation upgraded the Cr2O3 grade at 70 per cent Cr2O3 recovery from ~44 per cent Cr2O3 in the primary material to 46 per cent Cr2O3 (the target grade specification) in the secondary sample. It also showed that the stage crushing of this +600 ¦m fraction at a cut-off level of one per cent SiO2 increased the cumulative Cr2O3 recovery from ~50 per cent in the primary material to ~63 per cent in the secondary sample in the same size range of -600+106 ¦m. The extent to which additional crushing could lead to improved chromite recoveries at the required chromite and silica grade target specifications was not determined. This experience demonstrates that prior to processing test work being conducted, a thorough understanding of the chemistry and mineralogy of the test sample promotes efficient and targeted processing research.

Jan 1, 2008

By H. K. Lin

The effect of metallic iron fines on froth flotation of a sulfide ore was examined by comparing the flotation results with and without iron fines present in the flotation feed. Mild steel and ceramic laboratory ball mills were used to grind 600 g sulfide ore charges. The mild steel ball mill generated approximately 4.6 g of iron fines (0.8% of the ore charge mass) when grinding to a product size of 80% passing 200 mesh (75 mm). When a low dosage of a weak xanthate collector was used in flotation, the impact of the iron fines on sulfide flotation was marked. Higher dosages of stronger xanthate collectors rendered the impact of the iron fines much less significant. Consumption of the collectors by the powdery iron fines is believed to cause the differences observed in the flotation results. A galvanic effect on flotation was not evident in this study. The impact of the iron fines on silicates depression was also examined.

Jan 1, 2008

By Brett Campbell

The San Vicente to 2nd Aqueduct Pipeline?Tunnel project is a raw water conveyance tunnel linking the San Vicente Reservoir (SVR) to the 2nd Aqueduct Pipeline via Rancho Penasquitos Pressure Control Facility (RPPCF). This 58,230 lf long tunnel will be 8.5? final ID, and has four points of construction access. The job is classified into 6 Reaches of tunnel, identified by the dominant geology within the reach. This paper will focus on Reach 3, specifically the measures necessary to drill and blast a 550 lineal foot section of granitic rock tunnel immediately in front of an open face digger shield.

Jan 1, 2008

By M Fahey, A B. Fourie

Over the past ten years, the mining industry has witnessed the introduction of a new and innovative mine filling technique known as paste fill, which consists of placing full stream tailings with small amounts of binder and water into underground stopes. Paste fill has benefits over traditional backfill methods, such as higher solids contents than hydraulic fill and easier transportation than rock fill. From a geotechnical perspective, the behaviour of very fine material in a fully saturated state can be complex, particularly when binder is added. Previously, there has been no rigorous solution to understanding the paste fill deposition process, resulting in uncertainty regarding critical aspects such as barricade load calculations. This uncertainty has the obvious consequences of potential barricade failures (including at least 12 over the past four years), and for many operations attempts to deal with this uncertainty has led to excessively conservative filling schedules, restricting production. This paper presents an application of Minefill-2D, the first rigorous model capable of representing the paste fill deposition process. The model couples the processes of material accretion, consolidation and cement hydration to calculate the distribution of stress around a stope (including the total stress applied to barricade structures) during filling. Minefill-2D is a finite element numerical program, which has been verified using laboratory element tests, centrifuge tests and in situ measurements (Helinski, 2008). The authors present a sensitivity analysis, carried out using the model, to demonstrate some of the critical and less critical aspects relating to paste backfill deposition. The results of this sensitivity analysis are used to devise a fill management strategy that can be utilised to minimise the risk of barricade failures and maximise fill rates where appropriate.

Jan 1, 2008

By Steven J. Page

Researchers have developed a model to describe airborne respirable dust (ARD) generation on surface coal mine drills. By measuring a few basic parameters and using a graph, a drill operator or engi­neer can estimate the relative severity of drill dust emissions as well as how much of a reduction in ARD can be obtained by changing any given parameter. Geometric parameters include: drill deck cross-sectional area, shroud leakage associated with the deck shroud as well as the operational parameters of bailing air­flow, and dust collector airflow. The rela­tionships yield predictive ARD values which fall in the range measured on oper­ating drills for collector/bailing air flow ratios greater than 2. Overexposure to airborne respirable crystalline silica dust can cause serious or fatal respiratory disease. Exposures of sur­face coal mine rock drillers to respirable crystalline silica are of particular concern. In a 1992 alert on silicosis in rock drillers, the National Institute for Occupational Safety and Health (NIOSH) reported on 23 cases of advanced silicosis (acute, acceler­ated, and chronic) ranging in ages from 25 to 60 with drilling tenures ranging between three and 20 years.1 Most of the cases involved drill operators in their 30?s and 40?s, indicating high silica exposure levels are associated with their occupation. A more recent lung x-ray surveillance study of a 664 volunteer population of surface coal miners showed that the prevalence of silicosis-like abnormalities was 9%.2 The two most significant factors associated with these abnormalities were increasing age and years of drilling experience.

Jan 1, 2008

By R Bertuzzi

This paper presents a three-dimensional analysis of a trapezoidal-shaped segmental tunnel lining for a recent tunnelling project in Sydney. Two- dimensional analyses, hand calculations and equipment selection defined the lining geometry and loads. The analysis, which was undertaken using 3DEC (Itasca), included a complete ring of six segments bolted together to assess the impact of imperfectly built rings. Asymmetry was induced in the analysis by unfavourable positioning of segments within construction tolerances. Model output includes displacement and stress within the entire ring and normal, shear and bending moments at the joints. For the case analysed, the results suggest a 10 mm construction tolerance increases normal and shear stresses along the radial joints by approximately 25 per cent and 15 per cent, respectively and up to a doubling of the induced moments.

Jan 1, 2008

By Stephen Chung

The quality of a blast design can be evaluated in many ways. It may involve fragmentation, muck profile, environmental effects in terms of vibration and the excavation of the blasted material. To assist and ensure an achievable cost effective design, numerical modeling techniques are often applied as part of the operating procedure. While excavation is one of the mining operations which has a direct influence on the bottom line cost of productivity, the characteristics of a pile of blasted material deserves a closer look in terms of diggability. This paper reviews the current diggability techniques available for application to the blasting operation. To help better understand the involvement in digging, this paper also introduces an evaluation approach based on a discrete element method. The model presented in this paper deals with many variables that are considered to directly affect digging. They are the density and cohesion of material, fragment shape and size distribution as well as the swell of a muck pile. To help visualize the analysis approach, sample runs and animations are given in the paper to show the setup of muck piles produced in bench blasting as well as in sub-level caving. The computed forces experienced by the bucket during each mucking cycle are also discussed.

Jan 1, 2008

By Guozhu Ye, Mikael Larsson, Eric Burström, Sten Ångström

"Increased use of scrap in steelmaking including scrap use in BOF has a high economic and environmental potential in terms of increased productivity, energy saving and reduced emission of CO2. Preheating and surface cleaning of steel scrap is a concept developed by MEFOS in a four year research program funded by MISTRA, Swedish Foundation of Strategic Environmental Research. The process concept consists of four major steps: 1) Combustion of ASR or other waste fuel and composing of the gas composition. 2) Scrap heating and cleaning in a shaft where the coated zinc is removed as ZnCl2 and scrap is heated to about 600 ºC. 3) Dust separation for recovery of metal zinc. 4) Gas cleaning. This paper will describe the process concept and highlight the major results from preliminary trials around the scrap heating and cleaning shaft.IntroductionSteel is often coated to increase the corrosion resistance. Share of coated and galvanized steel in the world marked is steadily increasing. This results in increased amounts of scrap with different types of coatings. Use of galvanized scrap in EAF plant results in an EAF dust with high content of zinc ferrite and many other impurities like Pb, Hg, Cd and halide. EAF dust is classified as hazardous waste in most of the developed countries and the steel plant has to pay for external treatment for zinc recovery. For use in BOF plant this will result in a BOF dust containing typically 1-5%Zn making it impossible for recycling to the blast furnace.Different approaches for surface cleaning have been investigated in past. Dapper et al. [1] examined the possibility to evaporate Zn, Ni, Cr, Sn from coated materials using chlorine. Chlorinated rinsing of non iron oxides and metals using HCl from combustion of PVC was discussed by Fray [2]. Further studies by Tee and Fray [3-5] have been concentrated on the possibility to vaporize coatings with an air and chlorine gas mixture. The O2:Cl2 ratio in the gas mixture was found to have great importance for control of the process. To avoid the chlorination of iron, this ratio should be kept at a level of 10:1.Scrap pre-heating up to about 600 ºC is a well known method and this alone could save up to 100 kWh per ton steel. The technology has been established since many years and efficient processes were developed in the 90’s. However, no process has fully gained the expected energy savings as the large quantity of the exhaust gas has to be reheated to over 1000 ºC again to destroy the hazardous components like dioxins."

Jan 1, 2008

By Michael Schmalzel

Freeport-McMoRan Copper & Gold, Inc. (FMI) will soon begin copper production from the Dos Pobres and San Juan deposits near Safford, Arizona. Ore reserves total 615 M tons grading 0.36% copper, predominantly as chrysocolla. Copper extraction will be by leaching with sulfuric acid. Fluor Canada Ltd. provided EPCM services to design an ore handling and conventional SWEW facility capable of producing a nominal 240 million pounds per year of cathode copper. The ore handling facility will process 114,000 tons per day of ore through three-stage, open-circuit crushing followed by agglomeration and product placement on the permanent leach pad. Stacking of ore on the leach pad will utilize Terra Nova Technologies' "Super Portable" mobile stacking system. The stacking system fleet consists of 13 self- propelled, crawler-mounted mobile conveyor units, each with 72-inch-wide belting and a capacity of 6,800 tons per hour, including ten 250-foot-long portable conveyors, a horizontal feed conveyor, a 285-foot-long horizontal conveyor and a 220-foot-long radial stacker. PROJECT BACKGROUND Project History The Safford Leach Project is located in the Safford mining district in Graham County, Arizona, approximately eight miles northeast of the town of Safford and 170 miles east of Phoenix. The 3,360-acre property is located in the Gila River Valley, immediately south of the Gila Mountains, at elevations between approximately 3,000 and 5,400 feet above sea level. The Safford Leach Project is comprised of the Dos Pobres and San Juan deposits, two of five known copper ore deposits in the Safford mining district.

Jan 1, 2008

By Edward Jacobsen, Patrick J. Lydon

"The ongoing expansion of the Oak Creek Power Plant in Oak Creek, Wisc., includes a tunnel bored in rock that connects to four vertical intake shafts approximately 1.5 miles (2.4 km) offshore in Lake Michigan. In 2004, Case Foundation Company was awarded a lump sum contract to install these intake shafts. In spite of delays that shortened the May to September construction season by up to 50%, four shafts and liner assemblies were drilled in 2005 and 2006. The shafts were connected to the tunnel in 2007 by mining upward to reach the lower portion of each liner and then removing its internal bulkheads so that lake water fl owed into the tunnel. The project is one of the largest private construction projects ever undertaken in Wisconsin. The expansion adds 1,230 megawatts of generation. In addition to the tunnel and offshore work, there will be 16 miles (26 km) of railroad track and 6 million cubic yards (4,600,000 m3) of earth work. The 27 ft (8.2 m) diameter tunnel, drilled some 150 ft (46 m) below the surface of Lake Michigan, originates onshore at a pump house. A structural slurry wall was constructed as the foundation for the pump house. The tunnel passes to the south near the current water intake before bearing east toward the new offshore intake shafts, which are 12 ft (3.6 m) diameter by 108 ft (33 m) long steel liner assemblies. These were grouted in place from approximately 3 ft (1 m) above the crown of the intake tunnel and then to 20 ft (6 m) below the lake bottom.Site GeologyOffshore. The plant site is north of the Racine-Milwaukee county line in an area affected by glacial activity. The soil conditions encountered at each shaft location were consistent, with noticeable variations occurring in the top of rock elevations that sloped downward from the innermost to the outermost shaft."

Jan 1, 2008

By James W. Marold

Tunnel and shaft plugs have been designed to assist in construction of new and rehabilitation of existing tunnels and shafts. Tunnel plugs have been used to provide construction access for side by side tunnels, separation of raw and treated water, and to allow operation of one tunnel during construction of a nearby tunnel. Shaft plugs have been used to seal up surface openings to tunnels and to prevent seepage of water to the surface through adjacent tunnels or shafts. The design construction details of tunnel and shaft plugs are provided. Typical examples of tunnel and shaft plugs are provided.

Jan 1, 2008

By Stephen A. Orr

Underground mining is a dynamic art and science with a diverse set of design, production, and economic criteria that must be considered before selecting an optimal method to extract the ore. While all methods can be technically classified as either self-supported, supported, or caving, the multitude of subsystems and existing variations bear witness to the fact that each orebody is unique and, as such, justifies an individual approach to optimize mineral extraction. In this sense, underground mining is an art. The ability to evaluate the unique characteristics of each ore body and utilize sound engineering principles to design the optimal system constitutes effective method selection. The task by no means ends at this juncture, however. Subsequent implementation requires an ability for modification. Very rarely are all the facts available to make a concrete decision prior to development of the resource. As a result, the risk of a wrong decision can never be eliminated. This requires a significant degree of flexibility with each method. Each unit of exploration, development, or exploitation work contributed to a deposit enhances knowledge of the ore body. The best mining methods are those that correctly account for the known parameters but provide an allowance for change at minimal cost and adapt to unanticipated conditions.

Jan 1, 2008

By Milance Mitovski, Milorad Cirkovic, Vlastimir Trujic, Dragana Živkovic

"In this article, it is analysed the possibilitis and the effects utility waste energy of process sulfuric acid production in the existing technical-technological conditions. The utility second process energy, reduction the fuels consumption, reduction environment pollution and its effects are shown, too. High heat quantity is produced as the result of exothermal reactions in the production process of sulfuric acid in Bor. A part of this heat is sufficient for the process development, and significant part of this heat presents low-temperature heat energy that is irretrievable lost. Investigations were carried out based on production of 485 t of monohydrate/day of sulfuric acid. By recovery of this heat quantity for heating purposes, about 20.000 – 25.000 t of coal/year would be saved, what would significantly improve the power efficiency of the smelter copper production. IntroductionTechnological process of copper production in RTB BOR (Serbia) produces a significant quantities of high temperature secondary (waste) heat energy that is uncontrolled “lost” in the vicinity. Secondary heat energy is produced in pyrometallurgical copper production in quantity of 1,621 kWth/kg of dry concentrate or existing heat (that presents a difference of heat at furnace outlet and heat at temperature over temperature of dew point of sulphuric acid gases) in quantity of 1,315 kWth/kg of dry concentrate. For designed capacity of Copper Smelter in Bor, the existing heat power of secondary energy is 92,111 MWt, what is an equivalent to the power of steam-turbo plant where the Rankine-Clausius heating cycle is done, and that is 28,334 MWe."

Jan 1, 2008

By J. A. Organiscak

Enclosed cabs are a primary means of reducing the silica dust exposure of equipment operators at surface mines. The National Institute for Occupational Safety and Health (NIOSH) has investigated various factor effects on enclosed cab air filtration system performance. Factors experimen­tally investigated were intake filter efficiency, intake air leakage, intake filter loading (filter flow resistance), recirculation filter use and wind velocity effects on cab penetra­tion (inside to outside cab concentration ratio). Adding an intake pressurizer fan to the filtration system was also investigated. Results indicate that the intake filter efficiency and recirculation filter were the two most influential factors on cab penetration. Use of a recirculation filter significantly reduced cab penetration over the intake air filter by itself due to the multiplicable filtration of the cab interior air. Cab penetration was also affected to a lesser extent by intake filter loading and air leakage. Adding an intake pressurizer fan notably increased intake airflow and cab pressure while providing only minor changes to cab penetration.

Jan 1, 2008

By Gregory Molinda

NIOSH has recently completed a study of the interaction between polyurethane (PUR) and coal mine roof in order to determine the mechanism of reinforcement, in both highly fractured rock and unfractured rock. Four case studies of PUR rein­forcement are presented. At a West Virginia site, a borehole camera revealed the location of roof voids and guided the PUR injection. By injecting polyure­thane into a zone from 0.6 to 1.8 m (2?6 ft.) high in the roof, a roof beam was created and ongoing intersection falls were halted. In another highly fractured roof in a western Pennsylvania mine, a total of 5.8 cm (2.3 in.) of rubbleized rock was found in a zone up to 3 m (10 ft.) into the roof. Untargeted PUR injection filled approximately 1/2 of the fractures. These two case studies showed that it is not necessary to fill up 100% of the void space to create stability. In the other two field sites, polyurethane was injected into weak, but unfractured roof. Post-injec­tion video monitoring showed that weak bedding planes were hydraulically wedged open and polyure­thane injected along bedding. The reinforcement value of this injection method is limited because of the wafer-thin layer of PUR introduced along bedding, and the lack of a PUR ??webbing?? which would serve as a structural framework to provide strength. It was determined that video inspection prior to PUR injection can aid in identifying the fracture zones to target, and minimize ??blind?? pumping and loss of PUR.

Jan 1, 2008

By I. Kylmakorpi

In non-ferrous metal smelting, when the concentrate entering the furnace contains high levels of moisture, energy requirement for heating and drying increases and large volumes of exhaust are produced. To solve this problem, rotary dryers and flash dryers using direct heating, and also steam dryers using indirect heating have all been used for drying concentrate. The focus of this paper is to present the development and current applications of the Kumera Rotary steam dryer. The advantages of this technology are numerous, including reduced heating requirements, environmental friendliness, operation reliability and minimum maintenance needs; making it a top choice for drying concentrate.

Jan 1, 2008

By Jim Sarvinis, Mark Berkley, David Clarry, Jason Berzansky

"Technologies developed to sequester CO2 or use CO2 for enhanced fossil fuel recovery are currently being utilized across the globe. Taxation regimes and CO2 credit trading are becoming drivers for a number of projects. Some mining companies have also identified ancillary opportunity to sequester CO2 in their by-products; recent work in the alumina industry is a prime example. In addition to process plant emissions, mining companies are becoming increasingly aware of their overall carbon footprint, including CO2 generated during the production of utility power. New power plant designs, in various stages of development, include CO2 separation and sequestration techniques. This paper summarizes the state-of-the-art for these technologies; including integrated gasification combined cycle (IGCC) power plants. A concept to use the gasification products as reductant in metallurgical processes is also described. The relevance of technology from power plant designs with post-combustion capture to the processing of off-gas generated in metallurgical facilities is also reviewed.IntroductionGlobalization and international economic growth have led to an increase in energy demand worldwide, and a corresponding increase in greenhouse gas (GHG) emissions. In 2005, 81% of global energy supply came from fossil fuels [1]; and while alternative energy technologies are emerging, it will require many decades to curb society’s fossil fuel dependence. Given the global concern of climate change and its scientific relationship with anthropogenic carbon dioxide (CO2), there is at present great interest in the development of techniques to reduce emissions of CO2. While most of these efforts are related to power generation and energy efficiency, the development of technologies for CO2 capture may offer opportunities in reducing emissions from industrial processes."

Jan 1, 2008

By Zhigeng Xu

Pressure leach of a Yunnan marmatite concentrates with adding coal as the elemental sulfur disperser was investigated. The experimental results show that the coal with carbon content higher than 70% is incapable of dispersing elemental sulfur from minerals and cannot improve the leaching of zinc. The coal with low carbon content (lignite coal) can act as excellent sulfur-disperser in the pressure leaching at 423K. The mechanism of lignite coal as sulfur disperser was further discussed by ultraviolet, infra-red spectrum and mass spectrum.

Jan 1, 2008

By Jerry Pyatt

Lead has been used by mankind since before the Egyptian pyramids were built. Its durability provides for a continuum of innovation. As the largest integrated lead producer in the Western Hemisphere, The Doe Run Co. is committed to locating, mining, processing and sup-plying lead in ways that are responsible and sustainable. It takes ingenuity and resolve to successfully operate in the heavy industry field today. Doe Run is committed to applying responsibility through sustainability, lean manufacturing, safety, environmental stewardship, education and workforce development, and com-munity support.

Jan 1, 2008

By Norm Disley, Kingsley Hortin, Gertjan Bekkers

As part of the expansion of the Kidd Creek Mine to 2,682 meters (8800 feet) below surface, two largediameter 3000kW (4000HP) booster fans were installed at the 6000 level. Shortly after commissioning the fans, significant damage to the fan bearings were observed, forcing several shutdowns for repairs, which were very disruptive to the mine’s production process.

Jan 1, 2008