Search Documents

The residues produced during the incineration of leather scraps contain significant amount of chromium which can be recovered and reused in the tanning industry. The objective of this study is to develop a cost effective method for chromium recovery from leather ashes produced during the incineration of leather scraps using a fluidized bed incinerator. The entire process investigated involves fusion of leather ash with sodium carbonate in air to oxidise chromium to sodium chromate, leaching with distilled water to dissolve chromates, and chromium reduction from the hexavalent to trivalent state by sodium thiosulphate solution. The main factors affecting chromium extraction, such as temperature, reaction time, and sodium carbonate to leather ash ratio, were investigated. Based on the results obtained, almost 100% Cr extraction can be obtained at 700°C fusion temperature, sodium carbonate to ash weight ratio equal to 3 and retention time longer than 50 min.

Jan 1, 2006

By M. Aljarrah

The phase equilibria in the Mg-Al-Ca system was investigated experimentally by differential scanning calorimetry (DSC) and X-ray diffraction (XRD) techniques similarly the Mg-Al-Sr system has been studied using DSC and XRD as well as scanning electron microscopy/energy dispersive spectrometer (SEM/EDS) and quantitative electron probe micro-analysis (EPMA). A new ternary solid solution MgxAl4,xSr was confirmed in Mg-Al-Sr system, which is a substitutional solid solution of Mg atoms in Al4Sr. Maximum solubilities of 21.3 at.% Al in Mg17Sr2 and 11.4 at.% Al in Mg were observed. It was also noticed that Mg38Sr9 dissolved 12.5 at.% Al. In the Mg-Al-Ca ternary system, one of the invariant transformations predicted by thermodynamic modeling was verified experimentally and found to occur at 512°C with composition close to 10.8 at.% Ca, 79.5 at.% Mg and 9.7 at.% Al. A ternary solid solution (Mg,Al)2Ca was confirmed where large solid solubility of Al in Mg2Ca was observed.

Jan 1, 2006

By A. C. Legg, M. T. Malema

Keywords: Pyrometallurgy, flash, smelting, furnace, nickel, copper, Botswana BCL Limited operates the only Flash Smelting Furnace on the African continent, at Selebi-Phikwe, situated in north-eastern Botswana. The furnace was commissioned in 1973 and produces a high-grade sulphide matte containing nickel, copper and cobalt, which is shipped to refineries in Zimbabwe and Norway for further processing. This paper outlines the recent process improvements and plant expansions that have resulted in a capacity increase from 40 000 to 60 000 tons per annum of metal production.

Jan 1, 2006

The corrosion behaviour of a low carbon steel was investigated in natural seawater and various synthetic seawaters. It was found that the steel corroded nearly four times faster in a 3.5% NaCl solution than in natural seawater for an exposure time of 21 days. The corrosion rate after immersion in synthetic seawaters (ASTM D1141 and Marine Biological Laboratory seawater) is similar to the corrosion rate after immersion in natural seawater. Calcium carbonate (aragonite) deposits were found on the surface of the steel after immersion in natural seawater and the synthetic seawaters. Some magnesium-containing deposits were also found after immersion in the natural seawater. These deposits act as a barrier against oxygen diffusion and thereby lower the corrosion rate. The morphology of the calcium carbonate deposits that formed during immersion in the natural seawater is different from those formed during immersion in the synthetic seawaters. This may explain the slightly lower corrosion rates obtained in the natural seawater. X-ray diffraction also showed that the oxy-hydroxides formed in the 3.5% NaCl solution differed from those formed in the other solutions. Keywords: Corrosion, seawater, low carbon steel, 3.5% NaCl, aragonite

Jan 1, 2006

By Bjørn Nilsen, Brian J. Ballou

The Tellnes open pit mine in Southwestern Norway has been operating since 1960. The maximum height of pit walls is currently about 150 meters with the current mine plan extending this distance to 400 meters with slope stability being a major controlling factor. As a result of unfavorable combinations of directions of major joints and faults, local stability problems have occurred several places in the pits walls. Stability problems have affected the reliability of main transport roads on several occasions. Most of such incidents have occurred during heavy rainstorms and during periods of repeated freezing/thawing. This paper reviews some of the stability problems and the measures taken to deal with such stability problems.

Jan 1, 2006

By W. D. Guo

With an experimental apparatus developed recently, model tests on piles were conducted in sand subjected to triangular soil movement profiles. Four instrumented piles tests are reported, which show the pile behavior predominantly determined by soil sliding depth. Axial load can create additional bending moment and pile deflection, which also make mode of pile-soil interaction change with sliding depth. Limiting resistance was found 1.5~3 times higher than currently used for laterally loaded piles in sand.

Jan 1, 2006

The present work is mainly focused on developing intermetallic inert anodes for aluminum electrolysis. The anode alloy based on Al-Ti-Cu system was prepared by casting, followed by the application of a protective coating. Behaviour of corrosion and the passivation under anodic condition was characterized using the electrochemical and microscopic techniques. The results obtained clearly demonstrate that the oxide coating can provide good corrosion resistance via surface passivation of alloy anodes, rendering them inert in cryolite melt.

Jan 1, 2006

By Roberto Parra

The wear and corrosion phenomena in the furnace lining of the ferrous and non ferrous pyrometallurgical processes are complex problems where chemical, interfacial and mechanical phenomena are presents. The characteristics of the processes determine the conditions to which these materials are submitted, where the thermal conditions reached during the operation is one of the most important parameter. Assuming that all the degradation phenomena are thermal activated, the rate of the different steps of the wear mechanism will depend on the thermal field in the lining. In view to apply the independent physicochemical knowledge of degradation mechanisms to the analysis and design of furnace lining the methodology of the Nodal Wear Model (NWM) was done. It combines the mathematical modelling of the heat transfer in the lining with the physicochemical control equation for the wear-corrosion phenomena. The NWM has been applied to different examples: theoretical analysis, laboratory scale test and industrial applications. We present in this paper the theoretical background of the model and two examples of applications: the sole of an electric furnace and the earth of a blast furnace.

Jan 1, 2006

By F. A. Guo

Ultrafine-grained surface layers were obtained by surface mechanical attrition treatment (SMAT) in copper and titanium samples. The thermal properties of the deformed layers were characterized using a scanning thermal microscopy (SThM) that allows thermal conductivity to be mapped down to the submicrometer scale. A theoretical approach, based on this investigation, was used to calculate the heat flow from the probe tip to the sample and then estimate the thermal conductivities at different scanning positions. Experimental results and theoretical calculation demonstrate that SThM can be used as a powerful tool for the thermal property and microstructural analysis of ultrafine-grained microstructures.

Jan 1, 2006

By Li Rongxing

A general regular solution model put forward in this paper defines a general interaction parameter that includes both composition and temperature dependence. On the basis of this model, analytic express of solution excess properties was obtained by least square fit using the composition and temperature relations in binary alloy phase diagram. After some solution excess properties analytic expresses of correlated binary alloy system obtained, the analytic express of ternary alloy system could be obtained by superposition of general geometrical model. The ternary alloy system Pb-Sn-Zn has been predicted in terms of this method and the result was very in agreement with actual measured value.

Jan 1, 2006

This paper is for mine managers. It is about maintenance of mining equipment. This is an extremely broad subject so this paper is given with the caveat that it necessarily contains generalisations, not true in all cases, but broadly correct. The job of mine managers is to be good at making money from the excavation and preliminary treatment of mineral. To do this well, they need to understand the cost and value drivers in the business. This includes understanding the drivers associated with maintenance. Maintenance is often identified as a problem at mine sites. It is frequently listed as the cause of production shortfalls when reporting. The state of maintenance within mining as an industry is generally among the lower end of the range, when compared to manufacturing, petrochemicals, etc. Why is this? Experience and review of many audits and evaluations of maintenance has shown that some patterns are consistent with good performance and some consistent with poor performance. These often centre around the time horizon of the management team and are associated with knowing the sensitivity of the business to certain maintenance drivers and the mechanisms of maintenance and their results. To summarise, some common misunderstandings can be listed as statements that are obvious and extrapolations from those, which are not necessarily correct. For example: High availability of equipment is necessary for production. Incorrect extrapolation:focus on availability will produce high production. Design is often the greatest factor in determining the reliability of a mining machine. Incorrect extrapolation: the newest and biggest machines generally have the lowest cost operations. Operation has an enormous impact on machine productivity and reliability. Incorrect extrapolation: the fastest operators are generally the best from a productive point of view. Some maintenance improves the performance and reliability of machines. Incorrect extrapolation: more maintenance will give you more reliability. Some maintenance depends on disassembly and reassembly of components. Incorrect extrapolation: assembly is basically the reverse process of disassembly. Maintenance improvement in the mining industry in the last 15 years has focused largely on planning and systems improvement. Incorrect extrapolation: most of the problems in maintenance can be traced to a lack of planning. Actions based on flawed extrapolations will steer a business suboptimally. It is therefore important that the mine manager understands these issues so that the improvement effort can be directed to the greatest benefit.

Jan 1, 2006

By L Mariani, G. Mendoza-Suarez

In this investigation, TiH2 powders were coated with copper and nickel by electroless plating to delay hydrogen evolution. Copper-coated samples were found to have a mixed acicular (2D growth) and cauliflower (3D growth) morphology whereas the nickel-coated samples had a cauliflower morphology. Examinations of the coated powder cross-sections revealed that the coating thickness ranges from 0.2 µm to 4 µm. Uncoated areas on the powder surface and coating flakes unattached to TiH2 particles suggest poor adhesion between the coating and the substrate. The phase transformation undergone by the TiH2 during dehydrogenation was studied in samples taken at intermediary points in the heating cycles and examined by XRD. The findings reveal that as the powder is heated from room temperature to 800°C, it changes from TiH1.971 to Tiu and to aTi. Differential Thermal Analysis (DTA) was performed to study the effects of the coatings on the temperature of hydrogen release. It was found that increasing the number of plating iterations, and therefore the thickness of the coating, creates a significant shift in the temperature of gas release.

Jan 1, 2006

By H. Kurokawa

Sumitomo Metal Mining decided to expand copper production capacity of Toyo Smelter and Refinery to cope with the recent copper demand growth in Asia, and to survive by reducing cost. The expansion plan is promoted to increase electrorefined copper production capacity from 270,000 metric tons in 2001 to 450,000 metric tons in 2007. The major changes in smelting section are introduction of the rotary steam dryer, renewal of the feeding system for flash furnace, improvement of the concentrate burner, modification of the flash furnace cooling materials, renewal of the slag cleaning furnace, modification of the flash furnace waste heat boiler, installment of a new converter furnace, enlargement of two anode furnaces. In addition, the gas cleaning system was upgraded and the second acid plant was installed. In the refinery section, the existing tank houses have been operated at high current density of 300A/m2 using the conventional starting sheet cathode technology and moreover a new tank house utilizing the permanent cathode technology was constructed. Although the copper production capacity has been increased, SO2 emission has been kept the lowest in the world through consideration of influence on the environment by expansion project.

Jan 1, 2006

This symposium is dedicated to the lifetime achievements of Professor H.Y. Sohn. It covers the scientific fields, processing routes and investigation techniques in which Prof. Sohn has worked during his career and is based in the equally important three topical areas: Principles, Technologies, and Industrial practice. Professor Sohn was General Chair of the very first TMS Fall Extraction and Processing Symposium in 1983 in San Francisco which led to the Annual such symposia as this International symposium. Furthermore, the theme of that symposium was sulfide smelting, which is also included in this symposium. [ ] Professor Sohn was born in a beautiful dynastic capital Kaesung, Korea on August 21, 1941. He received his B.S. degree in 1962 from Seoul National University, M.Sc. in 1966 from the University of New Brunswick, Fredericton, N.B., Canada, and his Ph.D. degree in 1970 from theUniversity of California at Berkeley all in Chemical Engineering. After working as a Research Associate at the State University of New York at Buffalo and as a Research Engineer at Du Pont?s Engineering Technology Laboratory, Dr. Sohn joined the Department of Metallurgical Engineering at the University of Utah in 1974 and currently holds the ranks of Professor of Metallurgical Engineering and Adjunct Professor of Chemical Engineering.

Jan 1, 2006

By Philip Dubbeling

Conventional dynamic sheetpiling techniques are ill-suited to urban development because of the emission of excessive noise and ground vibrations. Drilled shafts and slurry walls alleviate some of these environmental concerns but add additional problems due to large bulky machines, reliance on dusty concrete plants and urban trucking grief. To solve these problems, pre-fabricated sheetpiles are hydraulically jacked-in by reaction principle using a compact and lightweight press-in machine, a so called the "Silent Piler". Through scientific analysis, definition and systemization of press-in machines and methods, new construction concepts such as the one-step approach, implant structures, functional design and life cycle design have been developed to comply with new basic construction principles.

Jan 1, 2006

By N Hungerford, A Coote, S Doyle, D Henderson, F Della-Pasqua

A systematic, detailed airborne geophysical programme carried out in the Taupo Volcanic Region (TVR) in 2005 by Glass Earth NZ Ltd culminated in the identification of 21 epithermal gold targets. In this paper we present the follow up ground-truthing results from the first target drilled, Tahunaatara (TAH).   The Tahunaatara target was identified by means of a multi-disciplinary integrated approach (ôdata interventionö) that defined and ranked the target as being highly prospective for epithermal gold mineralisation. A follow-up ground resistivity survey over the target area revealed the presence of a ôresistorö buried beneath an extensive cover of recent volcaniclastic material. Geochemical soil sampling carried out in conjunction with the resistivity survey yielded anomalous gold values.   The host unit at TAH consists primarily of flow banded rhyolitic lavas, volcaniclastic deposits and tuffs of the Ohakuri Ignimbrite with small outcrops of silicified bedded breccias forming local topographic highs. Results from the first orientation drill hole show wide zones of intense silicification, clay alteration and mineralisation. Sulphide mineralisation is disseminated throughout the core in association with hydrothermal replacement and also occurs in association with quartz veins and infill in fractures (sulphide-only veinlets as opposed to quartz + sulphide veinlets). Textural evidence from drill core indicates that hydrothermal fluid flow was multi-staged with potential for multi-stage gold, and other elements. The presence of polymictic hydrothermal eruptive breccias indicates a hydrothermal vent system.   Alteration varies from argillic to silicic, with pervasive adularia and vuggy silicification also present. Chlorite is minor and associated with quartz, illitic clay and adularia. Assay results currently available confirm the presence of anomalous gold values in association with zones of vuggy silica deposition and intense silicification.

Jan 1, 2006

The desire for minimising impacts of mining activities on the environment, and in particular, water resources; is usually tempered by the costs and practicalities of implementing æbest practiceÆ measures. This paper briefly discusses the theoretical and practical options for water management for typical mines and quarries in a range of environments to assess if adverse impacts can be completely eliminated or at least be perceived as doing so. The regulatory requirements for water resources management are usually an essential part of mine planning and operations that can be a primary focus for all stakeholders. As such they can distract attention from implementing best practice in water management for the benefit of the environment and the community for altruistic reasons that have a long-term benefit for the mining industry as a whole. Cost-effective options for supply, demand and quality management of water that comply with basic regulatory requirements are readily available. Making a mine æinvisibleÆ in a practical sense, in terms of impacts on water resources would require eliminating potentially contaminated discharges, minimising demand, maximising reuse and recycling and putting back a healthy proportion of the clean water that is taken out of the natural environment for use in mine operations. This may sound simple enough and there are many well-known standard approaches that are usually applied. But which are the most effective, and who benefits? New approaches to water management are becoming more affordable and can benefit the bottom line as well as the environment, but can they make a mine ædisappearÆ? The perception of whether a mine is æinvisibleÆ in terms of its impacts on water resources is as important as the actions taken to try to achieve such an objective. The viewpoints and thresholds of perceptions of the different stakeholders are therefore relevant to how ævisibleÆ mining activities become.

Jan 1, 2006

By P Atkinson, M P. Simpson, J R. Kyle

BM37 is a bonanza-grade (>30 ppm Au) ore shoot of the Maria Lode of the Karangahake adularia-sericite epithermal deposit in the southern Hauraki Goldfield. Samples from BM37 contain up to weight percent gold. The ore shoot is a vein that pinches and swells, but is typically tens of cm thick, and locally exceeds 0.5 m in true width. Gold occurs as irregular anhedral electrum grains that range up to 300 microns across and contain 38 to 59 wt per cent Au (ave. 52 wt per cent Au). Electrum occurs in sulphide-rich bands in association with pyrite, chalcopyrite, acanthite, galena, sphalerite, and local covellite. Lower grade samples contain local to rare mckinstryite [(Ag, Cu) 2S] and polybasite [(Ag, Cu) 16 (As, Sb) 2S11]. Pyrite from BM37 is nearly stoichiometric; it lacks the As that commonly occurs at up to percent levels in pyrite from other veins in the goldfield. Acanthite also contains low quantities of trace metals, and typically has less than 2.5 per cent Se. The vein shows complex textures. Bonanza grade sulphide-rich ginguro bands form discrete layers adjacent to the vein margins, and occur as breccia fragments encased by later massive to comb quartz with local quartz after platy calcite. Both the breccia fragments and ginguro bands are cross-cut by later quartz veins. Textures thus indicate that formation of the high-grade portions of BM37 resulted from one or more discrete events that differed markedly from the events that formed the bulk of the vein.

Jan 1, 2006

By G. Barrasso

REACH was proposed by the EU Commission in October 2003 and stands for the Registration Evaluation, Authorisation and Restriction of Chemicals. It requires that all substances identified as persistent, bio-accumulative and toxic, whether the risk of those chemicals being released is real or perceived, require registration prior to them being allowed to be imported into the European Union. An internal investigation by the metals industry indicates that almost all primary raw materials streams would be classified as hazardous due to the potential health or environmental hazard properties of one or more of their ingredients. REACH uses a wide definition for chemicals and metals and as such its implications greatly impact the entire supply chain of the metals industry. The process of registration would require the producer/ importer to produce a dossier. Initiatives along the same lines as the EU REACH are also coming up in other parts of the world. REACH requires registration of at least four substances manufactured by the aluminium industry: aluminium metal, including powder, aluminium oxide, and aluminium hydroxide. The proposed legislation permits the affected companies to band together to form a consortium to develop certain aspects of the registration application. The aluminium industry has established a consortium and testing is currently underway.

Jan 1, 2006

By Elli Nurminen

Fouling of heat recovery process equipment may significantly decrease their heat transfer efficiency. In Copper Flash Smelting process flue dust tends to form build-ups on the heat recovery boiler walls. Thermal transportation properties of copper flash smelting flue dust and its components have been studied. The effects of porosity and temperature on thermal transportation properties have also been determined. The results indicate that dust and its components are effective thermal insulators and build-up layers on the boiler walls are likely to decrease greatly the heat transfer efficiency of the boiler. Decreasing dust layer porosity has a strong increasing effect on thermal conductivity and increasing temperature has a slight decreasing effect on thermal conductivity. The results may be used in CFD-modelling and optimisation of the process.

Jan 1, 2006