Search Documents

By V. Saltas

In the present work, dielectric spectroscopy experiments were conducted on bentonite samples collected from Milos Island, in order to study their electrokinetic behavior in correlation with water content and mild heat treatment. Low-frequency dielectric spectroscopy has proved to be a power tool in the study of the electrical behavior of clay-water systems, because polarization and relaxation processes typically affect response at frequencies below 100 kHz. Therefore, dielectric and conductivity measurements in the frequency range of 10mHz to 1MHz were carried out by means of a high-resolution broadband spectrometer on bentonite samples, at various levels of hydration. The evolution of dielectric response was also examined after annealing of the samples. Experimental data were computer fitted with the empirical Havrilliak?Negami dielectric relaxation function on which a conductivity term was superimposed. The evaluated parameters of the fitting function are shown to be strongly affected by the water content of the measured samples.

Jan 1, 2006

By D. McConchie

BauxsolTM, prepared by treating bauxite refinery residues with Mg2+ and Ca2+, has an excellent ability to remove arsenic from acidic waters. The addition of BauxsolTM to sulphidic waste rock at the Gilt Edge Mine, South Dakota, reduced As concentrations in leachate water from 35 mg/L to < 0.005 mg/L; the concentrations have remained below 0.005 mg/L for the five years since the treatment was initiated. However, ordinary BauxsolTM does not effectively remove As from near-neutral water and it needs to be acid-treated or blended with small amounts of reagents, such as jarosite or ferrous sulphate, to increase the proportion of positively charged binding sites on the particles. The use of a jarosite/BauxsolTM blend can effectively treat ponded water, and As(V) concentrations can easily be reduced from over 1 mg/L to < 0.001 mg/L; As(III) has to be oxidised to As(V) for effective removal. Metal contaminants in the jarosite are trapped by the BauxsolTM and only very small amounts of the As, or other elements bound during treatment, are liberated using a TCLP leaching test. The exhausted treatment reagents meet the criteria for classification as an inert solid and do not need to be disposed of in a secure repository.

Jan 1, 2006

By E Baafi, G Brassington

Coal mining operations can impact on various types of surface infrastructure or natural features, including cliff-lines, steep slopes and natural watercourses. Longwall mining leads to a subsidence depression due to the changing geometry of the mined out area. The current regulatory process for managing subsidence in New South Wales (NSW) involves the preparation of a Subsidence Management Plan (SMP). This paper demonstrates the use of a Weights of Evidence (WofE) technique applied within a Geographical Information Systems (GIS) environment to predict potential areas for rockfalls along cliff-lines in the NSW Southern Coalfield. The WofE is a ædata-drivenÆ method that can be used to predict subsidence impacts prior to mining. The WofE method was applied to ten known rockfalls along the Cataract River to evaluate the reduced impact of not mining within 50 m of cliff-lines along the Nepean River. There is significant reduction of probabilities of rockfall occurrence when mining is avoided within 50 m of cliffs.

Jan 1, 2006

By Esher Hsu

In Taiwan, around 8,000 tons of batteries are consumed per year but only 17% of which were collected and transported to oversea for recovery. The dumping used batteries have become a potential environment problem. How to increase the collection efficiency of used batteries is an important issue for EPA in Taiwan. Besides, some treatment plants are on process to get permission for recovering used batteries. The objective of this study is to estimate the recycling cost of spent consumer battery and explore the feasibility of recovering used consumer batteries in Taiwan based upon the principle of cost-efficiency. The recycling cost including collection cost and recovery is estimated based on a survey. Results would provide some suggestions to Taiwan EPA regarding feasibility of recovering used batteries in Taiwan.

Jan 1, 2006

By Yavuz Ali Topkaya

Rare earth ferrosilicide is a versatile alloy mainly used to control the detrimental effects of sulfur in steel and to modify graphite structures in cast iron. The aim of this study was to determine the optimum conditions to make rare earth ferrosilicon alloy using a preconcentrate produced from a bastnasite type of ore present in the Beylikahir-Eskisehir region of Turkey. This concentrate contained 23.5%REO, 41.37% CaF2, 10.69% BaSO4, 8.50% CaCO3, 4.18%Fe2O3, 2.83% Al2O3, 2.74% SiO2, 1.20% P2O5 and small amount of other oxides. The initial metallothermic reduction of this concentrate using ferrosilicon and aluminum in a graphite crucible placed in a muffle furnace gave very low recoveries due to the difficulties encountered in adjusting the slag composition, temperature and amount of additives. Therefore, two batches of rare earth oxide concentrate containing 61.1% and 81.7% cerium oxide, respectively, that were procured from a Turkish glass producer, were used to optimize with respect to temperature, duration, slag-making additives and amount of reducers. In these experiments, smelting and reduction was done in an induction furnace with graphite crucible, and, ferrosilicon and aluminum were added after melting the charge. As a result, there was no difficulty in obtaining a rare earth ferrosilicon alloy containing 35-55% RE, 5-25% Fe and 20-40% Si, with about 80% metal recovery. When the optimum conditions were applied to the preconcentrate, alloys of similar compositions were obtained with 70-80% recovery. Experiments were also done with mixtures of preconcentrate and rich concentrate, and, recoveries as high as 95% were obtained. Only in this case, to increase the recovery, mixtures had to be charged to the empty graphite crucible after heating the crucible to the required temperature.

Jan 1, 2006

By Francis Vanbellen

Umicore Precious Metals Refining operates an integrated precious metals smelting and refining plant in Hoboken, Belgium. Once a smelter and refiner of complex concentrates, the plant today?s feed consists exclusively of industrial and consumer recycled products, making it the world?s largest recycling facility for precious metals. Unlike the fairy tale of the Frog Prince, it took much more than a princess? kiss to successfully realize this makeover. A completely renewed plant has been built over the past decade. The most visible technological innovation was the commissioning of the Pb-Cu smelter. Its flexibility towards very different types of feed makes it perfectly suited as main entry to the Hoboken flow sheet. A new Cu-leaching & electro winning plant and precious metals refinery make up the Precious Metals Operations (PMO) whose targets are fast throughput and maximized yields for gold, silver and the platinum group metals. The Base Metals Operations (BMO), flexibly process the by-products from the PMO, valorizing ?impurities? like indium, tellurium, selenium and others. Off gas and waste water treatments ensure compliance with strict environmental standards. Precious metals recycling is an art that goes beyond mastering a unique flow sheet. Umicore Precious Metals Refining offers a complete recycling service, taking care of sampling and assaying, metals management and logistics. The quality of this integral service is recognized through the attribution of ISO certifications for our operational activities, sampling and the environmental care. And it?s an art that follows Michelangelo?s experience: ?Art is 5% of inspiration and 95% of transpiration.?

Jan 1, 2006

By H. E. Urtubia

"BHP-Billiton’s Minera Escondida Limitada, in Chile, is one of the world’s largest copper producers. It treats a combined 10,500 tph of copper ore through its two concentrators: Los Colorados and Laguna Seca. The performance of the rougher circuit at each concentrator was measured and analysed using the JKTech flotation optimisation methodology. This involved developing a flotation model for each concentrator based on cell operating parameters (for example bubble surface area flux and froth recovery) and feed ore floatability characteristics. The rougher circuit performance was evaluated in terms of traditional measures, such as grade and recovery. The operation was also analysed using the measured cell operating parameters and ore floatability and the effect of these with regard to performance (grade / recovery) was assessed.This paper presents a comparison of the rougher circuit at each concentrator in terms of these parameters. The main differences in rougher circuit performance between the two plants were attributed to differences in feed ore floatability characteristics and froth recovery. The comparison highlighted opportunities where performance improvements could be made. The study also showed the usefulness of separating the flotation process into easily measurable subprocesses to further identify the different mechanisms occurring in each rougher circuit. Traditional measures like grade and recovery are useful for monitoring flotation operation but this data lacks the depth to determine the root cause behind operational issues. Determining the operating parameters and ore floatability provides the operating plant metallurgist better tools to assess and manage these issues."

Jan 1, 2006

By Tim Ross

Several shear failures were observed in Shaft #1 at the Mountain Coal Company, LLC, West Elk Mine, after mining longwall Panel 23, 1,100 ft to the east of Shaft #1. It was speculated that this shear damage could be related to differential ground movement caused by in situ stress relief from the ?stress shadow? of the caved zone above longwall Panel 23. A numerical study was conducted to assess the possibility of the shaft shear damage being caused by in situ stress relief and the potential for additional damage to Shaft #1 and two other nearby shafts, due to mining nearby longwall Panel 24. Three-dimensional (3D) models were built in FLAC3D to simulate past and future mining near shafts, the estimated local anisotropic and directional horizontal stresses, and the overlying variable surface topography. The numerical analyses indicated that stress relief due to mining Panel 23 caused the shear damage to Shaft #1and that additional damage to Shaft #1 and the other two shafts, would likely result from mining longwall Panel 24. Additional shear damage was documented in Shaft #1 when longwall Panel 24 was mined, confirming the results of the numerical analyses.

Jan 1, 2006

By Armando Valenzuela

Arsenic has been a common impurity in copper sulfide concentrates treated pyrometallurgically in Chile, which inevitably during the smelting-converting process reports in the final copper product affecting its properties, but also affecting environment as a very toxic occupational hazard. The enforcement of air quality standards, which regulate pollutants such as sulfur dioxide, particulate matter, and arsenic, has resulted in the implementation of pollution abatement plans and emission reduction schedules mainly by state-owned copper concentrate smelters. Investments associated with these plans incorporated gas-handling systems in order to capture polluting emissions. Electrostatic precipitators recover dusts containing mainly Cu and As which are leached to recover copper, while arsenic is disposed currently in the form of ferric arsenate. Gases containing high sulfur dioxide content are treated in plants to produce sulfuric acid, which is used in various classical and new hydrometallurgical processes. Additionally, smelters have effluents treatment plants for arsenic disposal either as ferric arsenate or calcium arsenate/arsenite. This paper reviews the environmental situation of the Chilean metallurgical industry, and the present trends for arsenic management are particularly emphasized since Chile is the world?s largest copper producer.

Jan 1, 2006

By Nam-Il Um

Bottom ash contains several ferrous materials (ferrous metals, Fe3O4, Fe2O3, FeS, etc.). In particular, ferrous metals contain heavy metal because Ni and Cr are chemically attracted to iron. Likewise, Cu is used to coat Ni and Cr metals as polish or to prevent corrosion. In this study, an Fe3O4-Fe2O3 double layer (similar to pure Fe) was found to have been formed in ferrous metal during air-annealing in an incinerator (1000°C). A strong thermal shock such as one that occurs during the water-cooling of bottom ash results in the breakdown of this oxidation layer, facilitating the degradation of ferrous metals and formation of corrosion products. Therefore, Fe-ion (heavy metal) oxides may be formed on ferrous metals and may be separated from bottom ash via magnetic separation. This study sought to investigate the separation ratio of heavy metals as magnetic separation and mineralogical formation of Fe-ion (heavy metal).

Jan 1, 2006

By Bern Klein, Malcolm Scoble, Justin Widdifield, Andrew Bamber

"It has been suggested that the pre-concentration of ore underground can bring positive economic and environmental benefits to underground mining, particularly at extreme depth. The integration of mineral processing systems for coarse waste rejection and disposal into the underground mining environment has a substantial impact on the economics and operation of the mine. A case study for the integration of underground pre-concentration at Falconbridge’s Thayer Lindsley and Fraser Copper operations in Sudbury, Ontario is discussed, with particular focus on ore evaluation, system design, integration, and impacts on the operation. Conclusions as to the overall feasibility and potential impacts of underground pre-concentration are presented.INTRODUCTIONObjectivesA scoping investigation has been conducted for Falconbridge Ltd on the Fraser Copper Zone and Thayer Lindsley mines in order to develop a better understanding of the operations, and to do a preliminary evaluation of the potential for pre-concentration of the ore underground. The objective was to develop a conceptual design and evaluation of a pre-concentration system for each site. The results are to be used as the basis for a more detailed future study.Underground Pre-ConcentrationThe pre-concentration of ore to reduce the quantity and improve the quality of material transported to the processing plant is not a new concept and has been in practise at several mines including the American Zinc Company in Mascot Tennessee (Munro et al, 1982), the Sullivan Mine in British Columbia and presently at Xstrata’s Mt Isa lead-zinc mine in Australia, as well as at several PGM mines operating in the South African Bushveld. For each of these mines, a high degree of waste rejection was achieved at a coarse particle size with good metallurgical recoveries. The benefits arising from the surface pre-concentration of ore are well documented in the literature (McCullough et al, 1999; Miller et al, 1978; Munro et al, 1982; Schena et al, 1990; Sivamohan & Forssberg, 1991)."

Jan 1, 2006

By D Craw, R Norris

The Golden Bar pit is part of the Macraes mine, the largest gold mine in New Zealand. The Macraes mine is mainly developed in the late metamorphic Hyde-Macraes Shear Zone. However, the Golden Bar pit was developed in a mineralised zone about 200 m structurally above the Hyde-Macraes Shear Zone. The host rocks are dominated by massive quartzofeldspathic schist (5 - 10 m layers) with minor intercalations (1 - 5 m scale) of micaceous schist. All the host schist has disseminated pyrite (micron to mm scale) from pervasive late metamorphic hydrothermal alteration. &nbsp; In addition, there has been more localised (metre scale) relatively intense hydrothermal alteration controlled by shears subparallel to foliation. Gold occurs in three types of mineralised rock: silicified schist, which dominates, fissile black sheared rock, and cross-cutting quartz veins. There are three principal structural zones in the deposit: 1. &nbsp; a strongly sheared micaceous and graphitic zone at the base of the structural sequence; 2. &nbsp; a weakly deformed schist zone cut by relatively flat-lying (= 20¦ dipping) quartz veins; and 3. &nbsp; a stack of imbricated schist pods and deformed silicified schist confined between two sub-parallel low-angle (ca. 30¦) shears. &nbsp; These structural zones were juxtaposed during thrust deformation. The lower black shear zone has m-scale folding and over-thrusting packages, kink folding and foliation stacking with associated striations that imply west-directed thrusting. Striations and imbrication geometry between the upper two shears imply oblique thrusting that was directed towards the west. Post-mineralisation normal faults locally disrupt the mineralised zone. The Golden Bar pit mineralised zone has some of the structural and mineralogical characteristics of the main Hyde-Macraes Shear Zone, and may be genetically related.

Jan 1, 2006

By T Sparks

The Collie River catchment, located approximately 200 km south of Perth, covers an area of around 2830 km2 and is the source of run-off to the Wellington Dam, an important irrigation water resource for the Collie Irrigation District. The salinity of the Wellington Dam has increased due to historical clearing and irrigators currently use water with salinity levels approximately twice that of the Murray River in South Australia (Water and Rivers Commission, 2001). The Collie River Salinity Situation Statement (2001), released by the Water and Rivers Commission (now the Department of Water), identified realistic actions that could achieve the salinity reduction target. Subsequent benefit-cost analyses and prefeasibility studies recommended the diversion of the most saline flows in the Collie River away from the dam as an immediate intervention (URS, 2003). The East Branch of the Collie River above the locality of Buckingham (20 km east of Collie) contributes around half of the salt that flows into the Wellington Dam and the diversion and storage of the saltiest flows from the East Branch at Buckingham was identified as a viable option for reducing salinity in Wellington Dam. The proposal had one problem û the water could not be disposed of as quickly as it was diverted. However, in the vicinity of the diversion site were a number of coal mine voids and after preliminary discussions, the Government/Griffin Coal alliance was formed and from this the opportunities have continued. Diverted water would be stored temporarily in an adjacent mine void (Chicken Creek 4 void) and then disposed of to the sea. The disposal options included Western Power CorporationÆs saline discharge pipeline from Collie Power Station, or a new pipeline. The diverted water was also identified as a potential raw source for treatment and use in industry. This has opened up opportunities including desalination, water efficiencies in the power stations, increased reliability of water supply for the power stations, water for new industries, wastewater disposal options and extra water for PerthÆs water supply. In the process of solving the water storage problems the project introduced a range of mine water quality problems û heavy metals and pH û and the Department of Water (DoW) is now working with the mining industry and the Centre for Sustainable Mine Lakes (CSML) to develop treatment and management technologies. The project has received support and funding through the National Action Plan for Salinity and Water Quality (NAP) and it has been possible to accelerate and enhance this project as a result of NAP. The DoW has developed the proposal to an advanced stage and gained approvals for the capital diversion program to go ahead. The partnerships have expanded to include the second mining company, Premier Coal, the Water Corporation, Western Power and the Harvey Irrigation Cooperative. The proposal could feasibly result in a $90 million integrated water management initiative for Collie using the latest technology, mining operations and providing water for value adding industries in the local area. The DoW is not a mining company; however, our experience in managing water in times of shortage, environmental water quality criteria, competition for water and managing community expectations will have the same success factors:consultation and knowing your community and stakeholders, sharing issues and working in partnership can provide results far greater than the initial issue, even brackish water has value, every sector is in competition with each other and has to have a share of the water, an integrated approach can provide opportunities for development in areas of water shortage, and never think of water as wastewater.

Jan 1, 2006

By Donald J. Hallbom

"While pipeline hydrotransport is often the most economical way to transport large volumes of mineral concentrate, tailings, or fine ore slurry over long distances, it is in mountainous terrain that pipelining becomes particularly attractive. These areas are often remote, with limited existing infrastructure and few potential users willing to share in the cost of new infrastructure. The rugged terrain makes the construction of railways or roads suitable for haul trucks difficult and expensive. The elevation difference between the mine and the terminal means that the empty trains or haul trucks need to return up-hill, resulting in high fuel costs. With pipelines, this elevation difference may reduce or even eliminate the need for pumping. As a result, numerous pipelines have been built, or are being considered, in mountainous regions around the world including: Tasmania, New Guinea, China, Madagascar, the Rockies of North America, and the Andes of South America. However, there are technical difficulties that need to be overcome in the design and operation of mountain pipelines that do not affect pipelines on more level terrain. This presentation reviews some of these difficulties and methods used to overcome them.INTRODUCTIONPipeline transport of solid-liquid slurry (“hydrotransport”) is an important and cost-effective means of transporting large volumes of solids over long distances, especially from a single supplier to a single user (e.g., a concentrator to a port, a concentrator to a tailings dam, or a coal mine to a power plant). Pipelines are generally found to be more economically attractive than alternate transportation methods (e.g. trucking, rail, conveyors, shipping, or some combination) over the life of a project (Aude et al. 1974).Hydrotransport systems have been built in a variety of terrains, but it is in mountainous regions that pipelining becomes particularly attractive. These regions are often remote and generally do not have existing transportation infrastructure (roads, railways, navigable rivers). There are few potential users (e.g., farmers, other mines, forestry companies, etc.) who may be willing to share in the cost of new infrastructure. The rugged terrain makes the construction and maintenance of railways or all weather roads suitable for large haul trucks difficult and expensive. Mines tend to be higher than the receiving terminal (e.g. a port). This means that the empty trains or haul trucks need to return up-hill, resulting in high fuel costs. With pipelines, this elevation difference may reduce or even eliminate the need for pumping. Pipelines are easier to construct than roads and railroads in these areas for several reasons, including:"

Jan 1, 2006

By William R. Yernberg

The Society of Economic Geologists (SEG) held its biennial conference May 14 through 16, 2006, in Keystone, CO. SEG is an international organization with about 3,500 individual members with interests in economic geology. The 2006 SEG conference theme was “Wealth creation in the minerals industry — integrating science, business and education.” The conference exceeded expectations with 705 participants, including 102 students, from 44 countries. The conference featured 30 oral presentations, 24 professional posters and more than 70 student posters. The conference also included a trade show with 50 vendors, numerous field trips, workshops and social activities.

Jan 1, 2006

By Jose R. Hernandez-Aguilar, Chris J. Martin, Rob Thorpe

"This study presents an approach to establishing relationships between metallurgical performance and the characteristics of the bubble population (gas dispersion) inside flotation cells. Bubble size Db, superficial gas velocity Jg, and bubble surface area flux Sb (Sb = 6Jg/Db) measurements were obtained along with metallurgical samples in full-size equipment processing different ore types. The gas dispersion was manipulated by changing the operating conditions of the cells (gas flowrate and frother type) and the metallurgical performance (grade-recovery) was determined. In two cases, the Sb had a strong relationship with grade and recovery, hence, Sb could be used as practical operating parameter. In another case, Sb did not correlate with recovery. The reasons were attributed to creating small bubbles using frothers with desired anti-coalescence properties. This illustrated that bubble size was the key parameter for metallurgy rather than Sb.INTRODUCTIONUnravelling the mechanisms that govern the relationships between metallurgical performance and the characteristics of the bubble population (gas dispersion) inside a flotation cell remains a major challenge. Information on this subject is scarce in the literature, particularly, plant-scale data. The report of Jameson and Allum (1984) appears to be the first gas dispersion study conducted in industrial (mechanical) cells. To introduce concepts, some aspects of their work are reviewed here.The prime motivation of that study was to establish whether any particular cell design (among 44 cells surveyed) could produce very small bubbles (< 0.1 mm), which laboratory research suggested would increase the recovery of fine particles. Although one of the outcomes was that the (examined) cells did not seem to produce such small bubbles (Sauter mean1 D32 ˜ 0.9 mm), the analysis highlighted the importance of including other factors. Jameson and Allum indicated that, besides bubble size (Db), other characteristics of the bubble dispersion should be considered, namely: gas holdup ?g – the fraction of cell volume occupied by bubbles, superficial gas velocity Jg – is the gas flowrate divided by the cross-sectional area of the cell and, bubble surface area flux Sb – the rate of production of (new) bubble surface area (m2/s) per m2 of cell cross-sectional area. It should be noted that, whereas Jg, ?g and Db can be measured directly, the Sb is derived: Sb = 6Jg/Db, where Db is usually substituted by the Sauter mean diameter (D32)."

Jan 1, 2006

By Stephen C. Tadolini

The International Ground Control Conference in Mining has always provided an open forum for the publication, presentation, discussion, and often heated debate on roof bolting systems mostly with attention to how, when, and why they work. During the last 24 Conferences at least 170 papers have been presented by International Experts on these ?simple? devices that range in length from 30-inches to 20 ft and from 5/8 to 2 inches in diameter. Roof bolts are primarily mechanically anchored, glued, cemented, or driven. Bolts are placed vertically, angled, or tied together with special fixtures (trusses and slings). They have been termed active, passive, stick-slip, and several other descriptive acronyms or mining slang expressions. This retrospective paper will present the changes in bolt types and usage, point out some of the biggest myths and hail the most significant advances (according to the authors? opinions of course).

Jan 1, 2006

By Peter Middendorp

Pile foundations are widely applied in the Netherlands because of the soft soil conditions. One of the popular pile types are cast-in-situ piles, which have to be integrity tested to get accepted. Integrity testing has been applied for more than 30 years, with the number of integrity test performed nowadays exceeding 400,000 per year and subsequently there is a substantial amount of practical experience with this testing method. This paper will deal with some basics of integrity testing and describe some of the techniques that have been adopted in the Dutch pile testing practice, like detection of pile head defects with a spike type hammer pulse, and the site average or pile group average for the qualitative interpretation of measured signals.

Jan 1, 2006

By Rob Thomas

Main gate roof control during longwall retreat is subject to a significant increase in horizontal stress and risk. The implementation and management of an appropriate roof support design is as a result, an imperative requirement for any longwall mine and must in addition to the likely consequences of a roof fall, also consider the variables of the geotechnical environment, associated support costs and practicalities. This paper will therefore summarise a number of recent advances in main gate roof control in the Australian coal industry. Points considered include; (i) the ?Longwall Acceleration? concept, (ii) macro-scale horizontal stress notching, (iii) micro-scale horizontal stress notching, (iv) bedded versus laminated roof types and (v) the type of cable reinforcement used.

Jan 1, 2006

By R. Frim, S. D. Ukeles

The present U.S. production of bromine is from inland brines located in Arkansas and Michigan. The most concentrated domestic brines (up to 5,000 ppm bromide) are situated in Arkansas. Less concentrated brines (about 2,500 ppm bromide) are located in Michigan. The amount of bromine sold or used in the United States came from three companies operating in Arkansas and Michigan. Arkansas, with its six plants, was the leading U.S. state in bromine production. Bromine being the leading mineral commodity valuewise produced in the state. The Michigan bromine production was a byproduct of magnesium compounds production.

Jan 1, 2006