Search Documents

By R. Chiarizia

Third phase formation, i.e., the splitting of the organic phase in two layers, is a common feature observed, under conditions of high loading, for many solvent extraction systems of both analytical and industrial interest. Although this phenomenon has been investigated in a large number of works, a structural and physico-chemical description is still lacking. In this work, small-angle neutron scattering (SANS) data for the tri-n-butylphosphate (TBP)-n-octane,Th(NO3)4-HNO3 solvent extraction system have been interpreted using the Baxter model for hard-spheres with surface adhesion. The increase in scattering intensity in the low Q range, observed when increasing amounts of HNO3 and/or Th(NO3)4 are introduced into the organic phase, has been interpreted as arising from interactions between small reverse micelles containing three TBP molecules plus solutes in their polar core. This intermicellar attraction, under appropriate conditions, leads to third phase formation.

Jan 1, 2003

By Varadarajan Seshadri

A physical model based on similarity principles was constructed for simulating the RH degasser of CST (Companhia Siderurgica Tubarao, Vitoria, ES, Brazil) to evaluate the circulation rate of the metal which essentially defines the degree of exposure of the metal to vacuum in the chamber and thus of the refining rate, The circulation rate on the other hand will influence the decarburization rate and removal of dissolved gases like nitrogen and hence it is essential to optimise this parameter to get maximum refining efficiency with minimum refining times, thus improving the productivity of the secondary refining process. Mixing characteristics in the ladle is evaluated by pulse tracer addition using conductivity-meters located at the down leg as well as at several locations in the ladle. The influence of gas injection through nozzles in the upleg with simultaneous bottom injection of gas as well as nozzle blockage on the circulation rates were investigated. Also simulation experiments of kinetics of decarburization were carried out using CO2 adsorption-desorption process in sodium hydroxide solution as circulating fluid and the effect of, bottom gas flow rate in this case was also evaluated. The results were carried over to prototype and to optimize the process.

Jan 1, 2003

By A. Bouvard, N. Hoteit, E. Boidy, F. Pellet

In the context of the construction of an Underground Research Laboratory devoted to the feasibility studies of radioactive waste deposits, it appears of the utmost importance to study the long-term behaviour of rock, over a long time period. In this paper, some results of tests performed on the argillite from the Meuse-Haute-Marne site test in Eastern France are presented. Then a numerical simulation of one of this test using the viscoplastic damaging constitutive law proposed by Lemaitre is presented. Finally, this law is used to simulate numerically the behaviour of the rock at the wall of a circular tunnel in order to determine the extension and the change along the time of the Excavated Damaged Zone (EDZ). Advantages and limitations of the model are discussed. Dans le cadre de la réalisation d’un laboratoire de recherche souterrain conçu pour étudier la faisabilité d’installations de stockage de déchets radioactifs, il apparaît fondamental de caractériser non seulement le comportement viscoplastique à très long terme des matériaux mais aussi les phénomènes d’endommagement consécutif à la redistribution de contraintes provoquées par l’excavation des cavités. On présente ici les résultats d’essais réalisés sur les argilites du site de Meuse/Haute-Marne et destinés à caractériser leur comportement visco-endommageable. Il est ensuite procédé à une application de la loi viscoplastique endommageable de Lemaitre pour simuler l'un de ces tests. Les apports et les limites d'un tel modèle sont mis en évidence par des simulations numériques du comportement de la roche au pourtour d'une galerie circulaire permettant de suivre l’évolution au cours du temps de la zone endommagée (EDZ) à la paroi . Im Rahmen des Baus eines unterirdischen Forschungslabors für die Untersuchung der Machbarkeit von Deponien für radioaktive Abfälle erweist es sich als äußerst wichtig, das langfristige Verhalten von Gestein über einen langen Zeitraum zu untersuchen. Im vorliegenden Artikel werden einige Ergebnisse von Untersuchungen vorgestellt, die mit Tonschiefer aus der Meuse-Haute-Marne in Frankreich durchgeführt wurden. Anschließend wird eine numerische Simulation der Untersuchungen unter Verwendung des von Lemaitre vorgeschlagenen viskoplastischen Verformungsgesetzes vorgestellt. Schließlich wird dieses Gesetz auf die numerische Simulation eines Kreistunnels angewandt, um die Ausdehnung und die zeitliche Entwicklung der Auflockerungszone (EDZ) zu bestimmen. Es werden die Vorteile und Grenzen des Modells diskutiert.

Jan 1, 2003

By Yunqing Zhang

Roof failure occurs much more frequently at intersections than entries and crosscuts. Using a commercial finite element package, four-way and three-way intersections reinforced with the tensioned bolts are modeled. The 3-D model considers bolt pre-tension, bolt installation procedure, bedding planes and in-situ horizontal stresses. The modeling results from both four-way and three-way intersections are analyzed with regard to the intersection stability. The mechanisms of tensioned bolting at the intersections are investigated and some tensioned bolting guidelines for intersections are given. Based on this study, a better way to enhance intersection stability is to use longer bolts than entries or crosscuts and increase the bolt density near the intersection corners.

Jan 1, 2003

By Alan Bugden

Goedehoop colliery in South Africa has experienced a number of substantial roof falls in roadways and intersections. Many of these have been associated with geological slips and/or horizontal compressive stresses. This paper describes a numerical modelling study conducted after one such fall with the objective of clarifying the roof failure mechanism associated with these falls. The fall was located at an intersection and occurred as the last cut was being made to complete the intersection. One bounding surface of the fall was formed by the geological slip; the others were formed by fresh failure surfaces. The fall took place despite the slip being identified as a hazard and additional bolts being placed by the workforce. In conjunction with the modelling work tests were conducted on samples from the roof in which the fall occurred, these gave a U.C.S. of 80 -100MPa. Several in-situ stress tests had already been conducted at the mine; a further test was conducted close to the fall site. The tests show that the largest stresses are horizontal. However, the maximum stresses of 6-12MPa are small compared to the compressive strength of the root. Computer modelling highlighted a mechanism arising from the conjunction of a geological slip and horizontal compressive stresses that could result in tensile failure of the roof leading to the fall. Sensitivity studies were conducted to identify risk factors associated with this mechanism and the modelling results used to assist in formulating a support strategy to combat falls of this nature.

Jan 1, 2003

"The Australasian Joint Ore Reserves Committee (JORC), which is sponsored by the Australian mining industry and its professional organisations, developed the JORC Code to provide minimum standards for public reporting. JORC was first published in 1989 and later incorporated into the Listing Rules of the Australian and New Zealand Stock Exchanges making compliance mandatory for listing public companies in Australia and New Zealand."

Jan 1, 2003

By M. Arnesen

Mining professionals recognize the need to continuously evaluate and refine mine planning standards and scheduling. We must examine our current reality, and evaluate the following: •How well do our planning standards represent the actual mining process? •To what extent do they support the requirements of the downstream mining activities? •How we apply them to operational management and control? In most operations, mine-planning standards are global averages. Little differentiation is madein quantifying key planning variables. Often standards used in the long-term, are applied to the short-term, and the standards and scheduling precedents are only reviewed occasionally. Mine-planning standards applied to production schedules are often only focused on the management of functional mining performance, and play no role in managing the requirements of down stream processing. Many mining operations are characterized by high levels of fluctuation, and typically incorporate a wide range of factors and adjustments to compensate for deviations from performance targets, in mining operations as well as for the other business areas. The reason for using global averages is because of a lack of understanding of the causes of deviations that occur through the process, and the impact that they may have on the performance of the business as a whole. Average standards and factors are often used to quantify the variability in a system. From these average values, measurement standards and performance targets are derived for the planning and execution environments. During the execution of a plan/schedule there will be deviation in actual performance and the planned ‘average’ standards. In reality the ‘average’ conditions seldom occur and the impact of variability and interdependency are seldom constant or predictable. The predictability of variability and interdependency is further complicated by the fact that mining conditions have a role to play in the actual production performance, and they too are variable. By developing the throughput knowledge of our production systems, we can better understand the nature of variability and the interdependency within the systems as well as the impact of interdependency between the links in our production chains. With this knowledge, planning standards and scheduling precedents can be better defined and sensibly differentiated. This will improve planning and management of ore utilization, mining production and the effectiveness of processing. As a result the business will be more stable and predictable and business performance will be improved. The purpose of this paper is to describe: •At a high level, the scope for refining and differentiation in mine planning standards, and incorporating geological and plant parameters into mine scheduling. This will improve planning and scheduling and the overall performance of the mine. Given our current level of scientific knowledge and the technological tools at our disposal we should be able to plan and schedule production so that we can manage pro-actively and improve business performance. In doing so we can also improve reconciliation and value tracking through mining and processing •The flexibility and functionality of the XPAC planning and scheduling tool that will enable a throughput management approach.

Jan 1, 2003

By D Williams

Recent advances in global positioning systems (GPS), machine guidance technology and telemetry allow an unprecedented level of control of surface mining operations. GPS technology can now locate the bucket of a shovel or the blade of a dozer within 50 mm. Some of the outcomes possible are: precise selective mining û even when the ore is visually indistinguishable from waste; tracking grade and tonnage of every ore parcel through the mine; real time productivity monitoring; detailed post accident safety analysis; and tracking the movements of every piece of equipment. This paper will consider the contribution that GPS based machine control systems can make to ensuring that surface mining projects deliver the outcomes promised in the feasibility studies. Case studies of installations are presented.

Jan 1, 2003

By D. G. Hulbert, D. J. Oosthuizen, D. de V. van der Spuy

Expert Online, as a software system, is aimed at providing plant operators in the minerals industry with effective training and on-the-job assistance. It incorporates a number of features to achieve this goal, of which the most important is its ability to explain the dynamics of the plant and control system in simple language, mimicking an informed plant expert who has online access to the inner workings of the plant and control system. This is made possible by a novel form of Artificial Intelligence, called the Interpreting Expert System. Previous implementations of the IES were only capable of explaining controller actions. Expert Online will extend this capability to also perform the more difficult task of explaining process behaviour. Expert Online will implement three main processes, namely the accumulation of data from the controllers and plant models, the interpretation, processing and filtering of that data and lastly communicating the relevant information to the user, both as written messages and in other audio-visual forms. Although Expert Online is aimed at the operator, other plant personnel, like supervisors and plant managers, will also benefit from it. This paper focuses on the structural and functional design of Expert Online for implementation on the latest version of Mintek’s open control platform, PlantStar, highlighting advances and additions since the previous implementations of the Interpreting Expert System and concluding with an example illustrating some of the principles.

Jan 1, 2003

By Noel A. Warner

Modern steelmaking is based on direct use of oxygen in high intensity batch reactors. A totally new approach is proposed in this paper, based on the view that pursuit of high intensity is unlikely to lead to successful coal-based continuous steelmaking. By substituting carbon dioxide and water vapor as the oxidants rather than using oxygen directly, the intensity is greatly reduced. Accordingly, subsurface formation of carbon monoxide bubbles can be avoided by careful manipulation of the three participating rate processes, gaseous diffusion, interfacial chemical kinetics and liquid phase mass transfer. Steelmaking can then be carried out without explosive ejection of molten droplets and the generation of micro-spray but rather in a controlled and fume less fashion. The vital component is the introduction of generic melt circulation technology. Three melt circulation loops in series are envisaged. Starting with a composite feed of iron ore fines, pulverized coal and lime flux, a metallized solid raft floating on molten iron is propelled out of the ironmaking loop onto the first of two downstream steelmaking loops. In the first, a liquid slag is formed, primary decarburization is undertaken not with oxygen but rather with CO2 and H2O and the melt is desulfurized. The semi-product stream enters the third melt circulation loop, where open-channel decarburization is effected along with dephosphorization to yield a low carbon steel product. Alternatively, the melt leaves the last loop to irrigate a packed tower countercurrent to argon at around 100 mbar to continuously produce ultra-low carbon (ULC) steel.

Jan 1, 2003

By S. Crewdson

Vertical hoisting of materials using hoists and skips is common in the Mining Industry. These systems have a number of drawbacks, one being limited hoisting capacity at medium depths. FKC-Lake Shore and Metso Flexowell have been developing and installing vertical belts for medium depth shaft applications for many years, progressively going deeper whilst increasing belt capacity. The latest development from Metso the Pocketlift® belt advances this technology allowing higher tonnages to be lifted from greater depths. The design, manufacture, installation and operational experience of a 1818 tonnes capacity, 273 meters vertical lift Pocketlift® system at the White County Coal Pattiki 2 mine is the subject of this work.

Jan 1, 2003

By S. Fiore, M. C. Zanetti, C. Clerici

The processes and fluxes of a cast iron foundry plant located in the North of Italy were analyzed in order to determine the amount and kind of wastes produced from the different activities. The main fractions are the molding sands, furnace muds and powders coming from the dust abatement plant, the exhaust lime, the furnace refractory, the metallic shotting and the sludges and powders coming from the dust abatement plant of molding lines for a total production equal to 800 t/d. All wastes were sampled and particle-size and chemically characterized to evaluate the best recycling or reuse solutions. Wastes were sieved and divided in three categories according to the particle-size dimensions: below 0.1 mm, between 0.1 and 0.6 mm and above 0.6 mm. The fraction above 0.6 mm dimension underwent magnetic separation to recover and quantify the potentially available iron fraction. The fraction between 0.1 mm and 0.6 mm was chemically characterized in order to understand if it could be fed to the sand regeneration plant. The below 0.1 mm fraction was characterized to evaluate the following recycling and reuse solutions: additive for molding sands and/or raw material for the concrete industry.

Jan 1, 2003

By N. Sahay

Improvement in work place environment by conventional methods viz., installation of higher capacity fan, fans in parallel operation or booster fan is a risky proposition in many coal mines in India because of difficult geo-mining condition such as shallow depth, multi seam workings having thin parting and inter connected goaves one above the other. The situation is further worsened if the mines have fire affected sealed off area connected to different ventilation circuits. On many occasions circulation of more air quantity by increasing fan pressure have resulted in initiation of spontaneous heating. To address these problems, authors have made some improvement in conventional Dynamic Balancing of Pressure Technique and worked out few ventilation schemes which are aimed for neutralization of pressure differential across sealed off area at the same time having improvement in ventilation in the mine. The excess pressure differential across sealed off area is mainly caused by introduction of higher capacity fan. Similar situation prevailed in one of the mines of Jharia Coalfield, India. The problem was solved by application of the above technique. In this paper, brief description of the technique, the problem in the mine, results of investigation, computer simulation studies of various schemes and methodology adopted for implementation of the technique in the mine have been discussed in some detail. Keywords: Dynamic Balancing of Pressure Technique, Spontaneous heating, Work place environment.

Jan 1, 2003

By Katsunori Okaya, Toshio Inoue

"Movement of mill charge in the centrifugal mill is essentially dissimilar from that in the vibration mill with circular path despite the apparently similar mode in the motion of mill body. This dissimilarity is the reason for the substantial advantage regarding the comminution intensity of the centrifugal mill over the conventional vibration mill accounting approximately to one order of magnitude.Bradley et al. (1983) developed a math model regarding the mill charge as a lump. This model is presented in a simple equation with which motion of the mill charge can be predicted in terms of the parameters describing the specification and the operation of the centrifugal mill. This equation can be used to explain the power draft of the mill as well as the stability of mill operation. More recently, on the other hand, a numerical simulation technology called discrete element method (DEM) has become a vital vehicle for estimating the motion of the grinding media in the mill. The authors developed a mill simulator called ‘Mill Solver’. Mill Solver is designed to simulate various types of mills including centrifugal and vibration mills. The principle of this simulator is to calculate individual kinetic events of interaction of balls in the mill in a minute time interval, hence the mill performance can be constructed for estimation."

Jan 1, 2003

By Kathleen M. Kowalski-Trakofler

This paper discusses human judgment and decision making under stress. The authors review selected recent literature across various disciplines and suggest a definition of stress within the context of decision making during the management of emergencies. They also discuss fieldwork by the Pittsburgh Research Laboratory, NIOSH, which explores traumatic incident stress, the relationship between previous training and performance under stressful conditions, and human behaviour in underground mine fires. The authors assert that stress is one of the factors that decision makers must contend with in most life-or-death situations. They suggest that a better understanding of individual judgment and decision making activities whilst under stress would yield a better understanding of how people reach the choices they make in emergencies. This enhanced understanding would be of enormous value to emergency managers, researchers and policymakers.

Jan 1, 2003

By Yoichi Takeda

Copper solubility in Si02-CaO-FeOx slag equilibrated with copper matte in 10% S02 atmosphere at 1573K was estimated. Essential parameters are activity coefficients of copper oxide and sulfide, oxygen and sulfur potentials and activity of copper in the slag-matte system. A large number of experiments provide proper parameters to calculate copper solubility in slag. A classical thermodynamic model postulating CUOO.5 and CuSo.; molecules assists in estimating copper solubility in slag. Additions of Si02 and CaO reduce copper solubility almost in any condition. Copper loss, that is function copper solubility and slag volume, in the silica saturated Si02-FeOx binary slag is minimally equilibrated with less than 66% copper matte while copper loss in the 50% FeOx-SiOrCaO ternary slag saturated with 2CaOSi02 is minimally equilibrated with over 66% copper matte. This slag composition has potential for continuous copper converting, direct copper production or high-grade matte production.

Jan 1, 2003

By A. M. Hefny, F. P. Siew, P. G. Ranjith

Fracture initiation and propagation, being one of the most intensive subjects in rock mechanics; contribute significantly to the deformation of jointed rock masses. An experimental study on fractured granitic rock was carried out to determine the peak strength of specimen under triaxial loading conditions. The commonly observed failure mode for rock specimens in this study was found to be the shearing of the plane of weakness. The minimum peak strength of fractured rock is observed when the joint orientation is approximately 70° to the horizontal axis. Based on experimental test data, an empirical expression was developed to accommodate the effect of joint orientation and joint trace length in estimating the peak strength of fractured rocks. The predicted values of peak strength using the proposed equation well agree with the experimental results carried out on singly fractured specimens under triaxial loading conditions. The threshold stress values of crack initiation and propagation depend on joint geometrical parameters, their degree of interconnectivity, as well as surrounding stresses on the fracture plane.

Jan 1, 2003

Vertical flow systems (SAPS, vertical flow wetlands) are increasingly used for passive treatment of mine drainage that is net acid. Data on 30 systems in eastern US show that well designed systems typically add about 40 g/d/m2 of alkalinity to influent net acid water. If they are designed with a conservative loading rate of 25 g/d/m2 and carefully constructed, they produce net alkaline water. Alkalinity added depends on influent acidity, Fe, pH, and retention time, and ranges widely, from 7 to 484 mg/L, so this is not a useful design criterion. Some waters may benefit from retention times longer than the conventional 12 - 16 hours, but the design must be partly based on cost-benefit considerations. Systems with fine limestone added to the compost layer perform better than average, perhaps to an alkalinity generation rate of 80 g/m2/d. A variety of problems are noted in the 30 systems and others reported in the literature. Systems with high influent Fe (> ~75 mg/L, varying with pH) tend to gradually decrease in flow rate because of precipitation and settling of Fe hydroxides on top of the compost layer. Some high-Fe systems precipitate Fe in the limestone layer, suggesting inadequate compost thickness, or short-circuiting through thin spots. Systems with Al exceeding about 10 mg/L tend to plug because of Al hydroxide precipitation in the limestone layer. Flushing only removes a small part of this precipitate, but can extend life. Some systems are ineffective because of failure of the inflow system. Some systems are uneconomic because they are oversized. A continuing program of inspection and maintenance is necessary for long-term performance.

Jan 1, 2003

By J Mauk, J Rowland, S Rabone

Most epithermal Au-Ag deposits in the Hauraki Goldfield are hosted in late Miocene andesites. Broken Hills is an exception, being one of the few economic deposits hosted in rhyolite. Investigation of Broken Hills provides the opportunity to collate structural data that may be compared with that collected from andesite-hosted deposits in order to evaluate the importance of rock type on vein development. The rhyolite host rock at Broken Hills is strongly flow-banded, but this anisotropy does not appear to affect the orientation of mineralised structures. There is a range of structures at Broken Hills: veins, faults, fractures, and large breccia pipes. Veins generally strike north-south, with localised changes in strike and thickness. Slip vectors determined from striations indicate near pure dipslip on the main lode, indicating an extensional tectonic setting. The orientations of vein deflections are parallel to slip vectors. This correlation is common in modern extensional fault arrays where fault growth and linkage produces subvertical deflections in fault orientation (eg TVZ). There are three main types of breccias: 1. Primary breccias related to rhyolite emplacement. 2. Jigsaw type secondary breccias that are that developed during the life of the hydrothermal system. 3. Breccia pipes. Broken Hills was a dynamic epithermal mineralising system.

Jan 1, 2003

By M. Kawakami

In relation to the designing of a new-type blast furnace, the reaction of carbonaceous materials with C02 is expected to occur at as low temperature as possible. In order to get a highly reactive carbonaceous material at low temperature, the reaction kinetics was investigated by measuring such quantities as the reaction rate from weight loss, the amount of CO adsorption and specific surface area by BET method. The reaction rates were large in the order of the Bintyo char, metallurgical coke, graphite and glassy carbon. If the rate was converted to the rate per unit area, however, those of the Bintyo char was smaller than that of graphite. Thus, it is suggested that the rate of the Bintyo char is influenced by the pore diffusion of C02. The rate had a positive relation with the amount of CO adsorption, showing that the rate determining step would be the desorption of CO from the active side on the surface. The rate independent of surface area was derived, combining al\ the obtained data.

Jan 1, 2003