Search Documents

By Nozomu Hasegawa

The phase diagrams and microstructures of the slags in the Mitsubishi Continuous Copper Smelting and Converting Process were studied for the prevention of the magnetite troubles such as accretion build-up on furnace hearths and launders, blockages at the melt outlet, slag viscosity increases and so on. According to the results of those studies, the silica and lime contents in the silicate slag at the smelting furnace, and the lime content in the lime-ferrite slag at the converting furnace were changed, resulting in lower and more consistent copper levels in the discard slag, with much less need for operators to clean melt outlets and launders. However, these changes may decrease the desirable amount of accretion-coating inside the furnaces and thereby reduce furnace campaign lives. Therefore, a method of estimating the magnetite level in the melts was developed, and slag compositions and temperatures have been controlled within the appropriate ranges to prolong furnace lives and also prevent magnetite troubles.

Jan 1, 2003

By K. Tozwa

The electrical conductivity of electrolytes for copper electrorefining and electrowinning processes has been reported by many researchers since 1911. The experimental results show that the conductivity increases with an increase in sulfuric acid concentration and decreascs with an increase in copper concentration. In pure copper sulfate solution, however, the conductivity increases with an increase in the copper concentration. After confirming the conductivity of pure and acidified copper sulfate solutions experimentally, the concentrations of hydrogen ion and free (not hydrated) water in the electrolytes were estimated and it was found that the relation between the conductivity of acidified copper sulfate electrolytes and the products of concentration of hydrogen ion and free water is linear. Accordingly, the conductivity of acidified copper sulfate electrolytes increases with an increase in sulfuric acid concentration and decreases with an increase in copper concentration.

Jan 1, 2003

"Industry Guide 7 contains the Securities and Exchange Commission’s basic mining disclosure policy. It provides guidance for Registrants on various matters including the definition and disclosure of proven and probable reserves and the definitions of exploration, development and production stages. The definitions and disclosure instructions contained in this Guide apply to all public mining entities and their public disclosures. As NI 43-101 is law in Canada, the SEC allows mineral resources and mineral reserves prepared under CIM Definition Standards for issuers that are reporting in Canada but are also registered with the SEC. The SEC places conditions on the disclosure of these estimates. US shareholders are cautioned that the requirements under NI 43-101 and the CIM Definition Standards differ significantly from those of Industry Guide 7.Note: this Guide contains the Commission's basic mining disclosure policy. The definitions and disclosure instructions contained in this Guide apply to all public mining entities and their public disclosures pursuant to the rules of Regulation S-K. Questions regarding the application of these definitions and rules to specific situations should be asked of the Commission's mining engineers or geologists at either the Office of Engineering, Division of Corporation Finance, 202-272-3252, or the Branch of Geology, Central Regional Office, 303-844-1000.(a) Definitions. The following definitions apply to registrants engaged or to be engaged in significant mining operations:(1) Reserve. That part of a mineral deposit which could be economically and legally extracted or produced at the time of the reserve determination.Note: Reserves are customarily stated in terms of DoreD when dealing with metalliferous minerals; when other materials such as coal, oil shale, tar, sands, limestone, etc. are involved, an appropriate term such as Drecoverable coalD may be substituted.(2) Proven (Measured) Reserves. Reserves for which (a) quantity is computed from dimensions revealed in outcrops, trenches, workings or drill holes, grade and/or quality are computed from the results of detailed sampling and (b) the sites for inspection, sampling and measurement are spaced so closely and the geologic character is so well defined that size, shape, depth and mineral content of reserves are well- established.(3) Probable (Indicated) Reserves. Reserves for which quantity and grade and/or quality are computed from information similar to that used for proven (measured) reserves, but the sites for inspection, sampling, and measurement are farther apart or are otherwise less adequately spaced. The degree of assurance, although lower than that for proven (measured) reserves, is high enough to assume continuity between points of observation.(4)(i) Exploration StageDincludes all issuers engaged in the search for mineral deposit (reserves) which are not in either the development or production stage."

Jan 1, 2003

By F. Peer

In most coal preparation processes, water is a necessary medium, but the presence of water in coal after it has been cleaned has a negative impact on transportation costs, handling and specific energy values. The utilization of super absorbent polymers (SAP) in the nappy application is well known. The concept of utilizing these polymers was investigated for the purposes of dewatering coal and other fines, generated by preparation processes such as flotation. SAPs are granular highly cross-linked synthetic copolymers with excellent water-absorbing properties. The dewatering process is characterized by three main stages: (a) contact of super absorbent polymer with high-moisture fine coal; (b) separation of dewatered fine coal from super absorbent polymer; and (c) regeneration of used super absorbent polymer, by exploiting its response to changes in conditions such as pH or temperature. Preliminary tests showed the separation step to be very difficult. The novel idea of encasing a given amount of polymer in a water permeable cloth solved this problem (of separating the swollen polymer from the dewatered coal). Preliminary tests investigating the effectiveness of the sachets of polymer showed a drastic decrease in the moisture contents of slurries. Furthermore, it was shown that it was possible to regenerate the polymer (still within the sachets) through thermal drying. A full-scale experimental programme was then followed to accurately determine the feasibility of using sachets of SAP. The experimental variables were initial slurry moisture content and polymer dosage. It was observed that the sachets seemed to work fastest and most effectively at high moistures and also at higher dosages of SAP. Regeneration of the polymer was also investigated, using two methods: thermal regeneration and pH-induced regeneration. The experimental variables, for investigating the regeneration process, were method of regeneration and grade of water used. Thermal regeneration at 70°C seemed to work successfully. Although the cost of using thermal energy is still a problem, the safety aspect (fire hazards) has been addressed since the polymer does not ignite when heated, unlike fine coal particles that may do so. The alternative method of regeneration, which exploits the pH-sensitivity of the polymer, was less successful, and further work needs to be conducted.

Jan 1, 2003

By Enrique Fernandez

The success of the excavation of a sewage tunnel in a very extreme geological conditions, from river deposits and sandy layers to hard dolomite, and several meters below the estuary under the sea water influence, shows that the choice of a right equipment together with the use of chemical products like foam and polymers enable to dig tunnels in unexpected areas and give solution to the environmental problems. The paper describes the excavation and support process as well as the adopted solutions in every material and during the cross through the intermediate shafts, also under sea influence.

Jan 1, 2003

By Dong-Hyun Kim Kim, Tai-Ro Lee, Young-Hwa Seo

Overbreak occurred inevitably in a tunnel excavation, is the main factor for increasing cost and period in tunnel projects. Furthermore the damage to the remaining rock mass related to the overbreak can give rise to a serious safety problem in tunnels. As a rule of thumb, causes for the overbreak are inaccuracy in drilling, the wrong design of blasting and selection of explosives, and heterogeneity in rock mass. Specially, the geological features of the rock mass around the periphery of an excavation are very important factors, so a lot of research has been conducted to describe this phenomena. But the geological rockmass classification for the overbreak and the method for decreasing the overbreak have not been fully established. Besides, the technical improvement of the charge method is needed as explosives for the smooth blasting have not functioned efficiently. In this study, the working face around periphery of an excavation has been continuously sectionalized to 5~ 6 parts, and the new Blastability Index for the overbreak based on 6 factors of RMD(Rock Mass Description), UCS(Uniaxial Compressive Strength) JPS(Joint Plane Spacing), JPO(Joint Plane Orientation), JPA(Joint Plane Aperture) and FM(Filling Material) is proposed to classify sections of the working face. On the basis of this classification, the distance between contour holes and the charging density are determined to minimize the overbreak. For controlling the charging density and improving the function of explosives, the New Deck Charge(N.D.C) method utilizing the deck charge effect and detonation transmission in hole has been developed.

Jan 1, 2003

The 15m high Inco flash furnace uptake was designed as a reaction chamber with the objective of destroying the H2S contained in the furnace off-gas by combustion with oxygen at about 1300°C. Until recently, the oxygen required for this purpose was injected through afterburners located at the bottom of the uptake. An undesirable side effect of this practice was the formation of build up accretions on the inside walls of the uptake. This buildup had a negative impact on both the furnace on line time and the control of the flash smelting process. In late 200 I, the afterburners were relocated to the roof of the uptake. As a result, about 80% of the uptake accretion buildup disappeared with obvious beneficial effects for the operation of the furnace. This paper discusses key flash smelting aspects that affect the operation of the flash furnace uptake such as the dusting rate, the formation of H2S in the freeboard of the furnace, and the impact of using coke to supply some of the heat required by the process. The mechanism of buildup formation and its dependence 'on uptake afterburners location are also examined. Prof. Yazawa's sulfide smelting thermodynamic relationships proved instrumental in understanding the conditions that influence the formation and the elimination of H2S and uptake buildup.

Jan 1, 2003

By J. -H. Wu, S. Nishiyama, Y. Ohnishi

The behaviors and stress distributions of the inclined jointed rock masses with different dip angles obtained from DDA are compared to the results of laboratory tests. By calculating the block stress distributions, it is confirmed that DDA can reproduce the arching around the trap door when lowering the trap door. The shapes of arching change with the angles of inclined layers. In addition, the earth pressures acting on the trap door shows non-symmetrical distributions when the layers are not horizontal. The stress concentration occurs in one side of the rock masses close to the trap door. Furthermore, the surface settlements are also related to the inclined angle, and the loosening zone in rock masses can be different from Terzghi’s theory [1]. Since, simulations have good agreements with the laboratory test , it demonstrates the applicability of DDA to explain the mechanical behaviors of tunnel, such as arching phenomenon, non-symmetrical earth pressure distributions acting on the trap door, and the surface settlement profile in the jointed rock masses. Dans cet article est décrite l’étude numérique du perçage d’un tunnel dans un massif de couches rocheuses jointes inclinées. La simulation à l’aide de l’Analyse de Déformation Discontinue (DDA), en faisant varier l’angle d’inclinaison des couches de roche, nous apporte des résultats en termes de distributions de contraintes et de comportement des couches, résultats qui sont ensuite comparés avec des résultats de tests en laboratoire. Les résultats confirment le fait que la DDA est capable de reproduire le phénomène d’arcage autour de la trappe lorsque la trappe s’abaisse. Les formes d’arcage varient selon l’angle d’inclinaison des couches de roche. Par ailleurs, lorsque les couches ne sont pas horizontales, la distribution de pression agissant sur la trappe est assymmétrique. La concentration de contraintes se produit du coté proche de la trappe. De plus, les tassements de surface dépendent eux aussi de l’angle d’inclinaison. En conséquence, les résultats de simulation sont en accord avec les tests en laboratoire, ce qui prouve que la DDA permet d’expliquer des comportements mécaniques du tunnel tels que l’arcage, les distributions assymmétiques de pression du sol sur la trappe, ainsi que le profil du tassement de surface dans la masse de roches jointes. Dieser Beitrag beschreibt eine numerische Studie über Tunnel im geklüftetem Fels. Das Verhalten und die Druckverteilungen in den unterschiedlich geneigten und geklüfteten Felsenmassen wird mit Hilfe des Discontinuous Deformation Analysis Programms (DDA) simuliert, und mit Laborversuchen verglichen. Die Resultate bestätigen, dass DDA der Gewölbewirkung im „Trapdoor“ Experiment gut reproduzieren kann. Die Form des Gewölbes, ändert sich mit unterschiedlichen Neigungswinkeln der Schichten. Bei geneigten Schichten entstehen unsymmetrische Druckverteilungen. Auch die Oberflächenabsenkung ist von dem Neigungswinkel abhängig. Die gute Übereinstimmung der Simulationen mit den Laborversuchen zeigt, dass die DDA-Methode gut geeignet ist, um das mechanische Verhalten von Tunneln, wie z.B. den Effekt der Gewölbewirkung, die unsymmetrischen Druckverteilungen bei geneigten Schichten, oder die Oberflächenabsenkung in geklüfteten Felsenmassen, zu erklären.

Jan 1, 2003

By J Fut=

The rotary drilling of rocks is widespread technology in mining and in tunnelling. The paper describes the results of research by aim to find relationships between optimal drilling and sound signal of drilling machine. The optimisation criterion has been formulated as the minimisation of specific energy with maximal effective speed of drilling in process of the rock disintegration. The research in this field has been made on experimental drilling stand. Our monitoring system has measured following variables: the pressing force of core drill, the revolutions of drilling head, the length of drilling, the time, the power, and the acoustic signals. For measurement of acoustic signals have been used very sensitively sound meter MEDIATOR 2238. From this measurements have been processed acoustic spectrums. Then we are found relationships between optimal control of drilling and composition of acoustic spectrum. On base of experimental results, we can formulate the optimal control following: æTo achieve the minimum difference between the equivalent sound level at the load and idle modes only at the representative frequency (f = 1000 Hz)Æ. The representative frequency dependences on type of the rock New method based on these relationships enables the optimal control of drilling machine by using measured acoustic signals only.

Jan 1, 2003

By C. Zangerl, K. F. Evans, S. Loew

ABSTRACT: Settlements above fractured crystalline rock masses are rarely observed and in the past, geotechnical engineers would not expect substantial subsidence to occur in association with a deep tunnelling project. However, recent high precision levelling measurements along the Gotthard pass road in central Switzerland, have revealed up to 12 cm of subsidence along sections that pass several hundred metres above the Gotthard highway tunnel. Large-scale consolidation resulting from tunnel drainage and pore pressure changes in the rock mass are believed to be the contributing mechanism. This paper presents results from an extensive numerical modelling study focussing on the processes responsible for this subsidence. Results derived from 2-D discontinuum (i.e. distinct-element) and continuum (i.e. finite-element) modelling show that both discrete fracture deformation (i.e. fracture closure and shear) and poro-elastic consolidation of the intact rock matrix equally contribute to the observed magnitudes and shape of the surface subsidence trough. RÉSUMÉ: Des tassements aux dessus de massifs cristallins sont rarement observés et par le passé les géotechniciens ne prévoyait pas de subsidence significative associée avec des projets de tunnel profond. Cependant, de récentes campagnes de nivellement haute précision le long de la route du Col du Gotthard (Suisse centrale), ont mis en évidence des subsidences atteignant 12 cm sur des sections passant plusieurs centaines de mètres au-dessus du tunnel routier du Gotthard. Le mécanisme invoqué pour expliquer ce phénomène est la consolidation à grande échelle due au drainage du tunnel et aux variations de pression de pore dans le massif rocheux. Cet article présente les résultats d’une modélisation numérique intensive mettant l’accent sur les processus responsables pour la subsidence. Ces résultats obtenus grâce à des modèles 2-D discontinus (p. ex. éléments distincts) et continus (p. ex. éléments finis) montrent que la déformation sur des fractures discrètes (fermeture de fractures, cisaillement) ainsi que la consolidation poro-élastique de la roche intacte contribuent également aux magnitudes et aux géométries de subsidence observée en surface. ZUSAMMENFASSUNG: Beachtliche Oberflächensenkungen in einem kristallinen Gebirge, deren Ursache im Vortrieb eines mehrere hundert Meter tiefgelegenen Tunnels liegt, wurden bisher nicht erwartet und beobachtet. Dennoch wurden nach dem Bau des Gotthardstrassentunnels, entlang der Gotthardpassstrasse Oberflächensenkungen mit einem Maximalbetrag von 12 cm bei der Auswertung von Präzisions-Nivellements entdeckt. Dieser Maximalbetrag wurde in einem granitischen Gneis gemessen. Die örtliche Übereinstimmung zwischen dem maximalem Senkungsbetrag und dem maximalem Wasserzufluss zum Tunnel, und die zeitliche Abfolge von Tunnelbau und auftretenden Oberflächensenkungen lassen hydromechanisch gekoppelte Prozesse als Ursache dieser Gebirgsverformungen vermuten. In dieser Arbeit werden die Ergebnisse ausgedehnter prozessorientierter numerischer Simulationen präsentiert. Resultate aus den 2-D Diskontinuum (d.h. distinct-element) und Kontinuum (d.h. finite element) Simulationen zeigen, dass beide Verformungsmechanismen, d.h. an diskreten Brüchen und der intakten Gesteinsmatrix, gleichbedeutend für die beobachteten Senkungsbeträge und der Form des Setzungstroges verantwortlich sind.

Jan 1, 2003

By Brad Marchant, Rick Lawrence, David Kratochvil

"BioteQ has successfully developed commercial operations for ARD treatment and selective metal recovery using the patented BioSulphide and Thiopaq® biological reduction technologies. The BioSulphide-Thiopaq process was developed to provide biogenic sulphide for the selective recovery of high purity metal concentrates from acidic wastewater, which are sold to recover capital costs and off-set water treatment costs. The BioSulphide-Thiopaq process can be used on a stand-alone basis or in conjunction with a lime circuit. Process advantages include: selective recovery of metals, very low metal concentrations in effluent, reduced waste sludge liability, reduced lime treatment costs and, in some cases, profitable sale of metal concentrates. Two case studies are presented to illustrate operations focused on metal recovery at the Caribou Mine, New Brunswick, Canada, and at Phelps Dodge, Arizona. A third case study is presented to highlight environmental control as well as metal recovery for treatment of ARD at the Raglan Mine in Northern Quebec. Process flowsheets, capital and operating costs are presented for the three case studies.INTRODUCTIONProtection of water quality has become one of the most important environmental challenges facing the mining industry. Although new mining projects can be designed to minimize impacts to the environment, many existing and abandoned mining operations have water quality problems. The principal cause of water contamination is acid rock drainage (ARD), which is generated when residual sulphide minerals in waste rock, tailings and other mine components and products are exposed to air and water. These reactions can produce acidity and elevated concentrations of metals in drainage and seepage that can adversely affect surface and groundwater resources. To meet regulatory criteria for water quality in the receiving environment, many mine operators must consider treatment of mine water and other effluents prior to discharge."

Jan 1, 2003

By K. Drescher

Excavations in deep level hard rock mines show rheological or time-dependent deformation responses to mining-induced stresses. These are generally not as dramatic as those seen in soft rock environments, such as potash and salt mines, but these deformations can nevertheless become substantial in time. It is usual to see total excavation closure at a much earlier stage than predicted by numerical models, and real-time measurements underground have confirmed that closure takes place on a more-or-less continuous basis, with highest closure rates observed after a blast and then slowly diminishing with passing time. This paper describes laboratory tests to determine the time-dependent response of hard rocks to loading, the results of the tests, and then quantifies these effects to explain the time-dependent phenomena observed underground. The primary intention of this work is to help explain the various time-dependent deformation processes around typical deep level hard rock tabular excavations. Three mechanisms were investigated in two typical hard rock types present in the deep level gold mines in South Africa, namely Ventersdorp Lava and Elsburg Quartzite. Uniaxial compression creep studies were done as the first part of the study followed by shear creep studies on discontinuities where crushed lava and crushed quartzite as well as a natural gouge were used as infilling. The last part of the study consisted of triaxial post-failure relaxation tests. The compression creep tests and the triaxial post-failure relaxation tests showed that the amount of energy dissipated by the lava is significantly less than for quartzite. For mines operating at depths greater than 2000 m the implication is that the lava must show a greater rockburst-proneness than the quartzite. Since the lava shows a lower post-failure stress relaxation, it can store sufficient energy for multiple rockbursts, which is seen in the clustering of multiple seismic events in the deep level mines. This study provides the first data available for energy change calculations in fractured rock masses, and provides the first general indications for rockburst intensities ahead of active mining faces.

Jan 1, 2003

By Yutaka Shiraishi

Two methods were developed to measure the viscosity of the slag from the glassy to the liquid states in an ascending temperature process. The first method employs rotating parallel plates within which is placed a solid cylindrical sample in line with a sphere. The second method uses a tube which is pushed into a sample held in a rotating crucible. Both methods were tested using standard glasses, including boron trioxide and NBS standard glass #711. The main difference between these two methods is in sample preparation. Comparative measurements between two methods were performed using a sodium boro-disilicate glass containing 5%mol of alumina. The results showed good agreement in the mid-range of glassy viscosities, 105 to 107 Pa.s. In the liquid state, there were no significant differences between the two methods.

Jan 1, 2003

By K. P. Kavun, M. N. Denisov

Discussed in the paper is the redesigned reserve/resource classification for solid minerals being put forth by the authors to replace the acting Russian classification of 19961. The new version is based on the traditional foundations of former Russian classifications and the principles of the ‘McKelvey box’, both categorizing mineral resources according to the degree of geological assurance and economic viability. Based on these approaches the classification deliberately deals with both reserve and resource categories very similar to those established by the Geneva Accords in terms of definitions implied. The authors proceed from the UN-ECE proposed concept of ‘reserves’ being a part of ‘total resources’ explored in great detail by geological and feasibility studies and economically mineable at the time of reporting. The draft classification distinguishes ‘proved’, ‘probable’ and ‘possible’ categories of reserves depending on the stage of feasibility assessment carried out, i.e. the degree of detail and accuracy with which modifying factors affecting mineability of an orebody are taken into account. The reserves are regarded as a product of feasibility assessment of ‘measured’, ‘indicated’ and ‘inferred’ resources. The portions of them not having been classified as ‘reserves’ are regarded as composed of two classes: ‘subeconomic’ and ‘potentially economic’ resources (or ‘resource base’). All the cells of the classification matrix are provided with traditional for Russia alphanumeric designations and appropriate UNFC codes. The classification scheme recommended is viewed as a step forward in improvement of the State inventory and reporting mineral resources in market conditions, conducive to cross-border professional collaboration in the field of providing reliable information on the mineral rawmaterials base of the world’s economy. Besides, it recommends an easy way to get rid of amethodological error in the UNFC classification scheme where consecutive stages of geologicalexploration are identified with a single inherent degree of geological assurance. Keywords: mineral resources, mineral reserves, classification, geological assurance, feasibility studies, subeconomic resources, undiscovered resources, competent person.

Jan 1, 2003

By Liping Yu Che, Xiaotie Wang, Mingli Cao, Jizu Yongfu Yuan

"It is difficult separating fluorite from Ca, Ba, Si intergrowth minerals than simple from Si, using common reagents such as combination of oleic acid or paraffin soap and water glass, but the finest quality fluorite concentrate whose grade is over 96%F must be required in chemical plant.This paper studies the flotation process of native fluorite from calcite, barite and silicate minerals whose flotation properties is similar to fluorite, using new effective collector H602 and new depressor S602 that is cheaper in cost, and describes the flotation properties. In order to determine optimum flotation separation condition, the effect of pulp pH, pulp temperature, pulp density and the effect of dosage of reagents on flotation were investigated and the flotation result was provided by oleic acid collector and the results of collector H602 were compared with those of collector oleic acid in the test. The test result of ore samples shows that at moderate pulp pH values (10.5-11.5) and other moderate technical conditions, the fluorite mineral can be obtained by new reagents and the rational reagents combination. The conclusion is 98%F of fluorite concentrate can be obtained, using the combination of H602 and S602 and only 5 steps in techniques. The paper discusses the mechanism of the flotation separation of fluorite mineral from intergrowth minerals."

Jan 1, 2003

By Y. H. Liu

Several foaming aluminum samples of different density were prepared in a semi?industrial scale experimental system, Their properties such as the energy absorption characteristics, mechanical properties, heat conductivity and acoustical properties were measured. The results showed that the foaming aluminum with a density of 0.5 to 0.6 g/em3J has the best energy absorption and this makes it suitable as the ensuring bar of the automobiles and also as a cushion material for the engine. The foaming aluminum with a density of 0.25 to 0.4 g/em3 has the best acoustical properties and heat conductivity resistance, which is suitable for the door filling material, the ceiling and the partition or the car engine.

Jan 1, 2003

By Ralph J. Holmes, Victor Sharp, Steven J. Spencer, CSIRO Minerals, Kevin J. Davey, Jonathan J. Campbell, Peter L. Phillips

"Improved measurement tools for monitoring and control of AG/SAG mill performance have a high level of interest in industry. Historically, acoustic emission monitoring has been widely used on SAG/AG/ball mills and hydrocyclones to provide new information on the conditions inside these devices affecting their performance. The current work was focused on a new technique using surface vibration monitoring of a number of pilot-scale and production-scale AG/SAG mills to yield insights into the events occurring in the mills. The development of relationships between signal analysis outputs and mill operating conditions can be used for soft-sensor measurement of mill process variables. The technique used an array of accelerometers mounted on the mill lifter bolts linked to a fast data acquisition system which monitored the surface waves generated during operation. Details of the system are presented. Mill operating variables were adjusted systematically to provide a wide range of operating conditions for surface vibration signal collection. The experimental approach is discussed.The signals acquired during the experiments were analysed using a range of techniques. The results show that strong relationships exist between measured vibration power (both total power and within certain frequency bands) and mill load level/power and mill speed. A new method for extraction of power spectral density and band power information on features of interest in a mill rotation cycle is also presented."

Jan 1, 2003

By Maurice Hunter

The paper outlines recent design developments in the computerization of surface crawler drills for the quarry industry. It references the technology firstly developed for the underground mining and construction industry, where automation and computerization has been in demand for a number of years.

Jan 1, 2003

A new technology for the treatment of copper nickel-containing concentrate after high-grade matte flotation to blister copper with the production of liquid silicate slags in a vertical autogenous unit with upper oxygen blow has been considered. The copper and nickel behavior in the process of sulphide copper concentrate interaction with silicate melt containing oxide copper has been studied. The general mechanisms of such interaction are found.

Jan 1, 2003

By Mark Svinkin

The purpose of this paper is to present an overview of recommended existing criteria of ground vibrations generated by blasting. It is shown that these criteria have limited liability because they were found for specific categories of structures. A new approach based on measurement of structure vibrations is suggested for assessment of damage in structures subjected to blasting vibrations. This approach provides the flexibility of implicitly considering a variety of soil-structure interaction and structure conditions. It is explained a new frequency-independent safe-level criterion of 51 mm/s (2 in/s) for the PPV of structural vibrations. Attention is brought to use seismographs properly calibrated for the required frequency range. Positive flexibility is demonstrated in assessment of structure and component of concern vibrations from blasting.

Jan 1, 2003