Search Documents

By J. M. Schaekers

In the first part of the article, the authors give a broad overview of the chemistry and some engineering aspects of bioleach processes, eventually leading to the important and critical issue of the stability of arsenic-containing residues, especially those derived from bioleaching of sulphidic gold ores. In the section ?Factors affecting arsenic stability? they give an excellent summary of the factors normally affecting the stability of such residues. This is followed by some valid comments on the suitability of a single leach test to evaluate the long-term stability of solid waste streams. However, they fail to mention that, up till now, no tests procedure has been accepted by either environmentalists or the mining/processing industry as a valid method to test the long-term stability of solid wastes. Their own method is no exception, although, like many others, it is useful to identify potential problems with solid wastes considered for disposal.

Jan 1, 2001

By Sandra Penttinen

To assist blasting professionals with the creation, documentation, and appropriate methodology to standardize the data collection of the pre and post blast investigation process. Penttinen Associates will present a logical non-technical presentation focusing on: Why pre-blast surveys SAVE How to prepare for pre-blast inspections What to do in preparation of pre-blast inspections The creation of an industry standard all-inclusive pre-blast document Establishing pre-blast inspection operational standards Preserving the data.

Jan 1, 2001

By Jacques Magnaudet, Julie Cranga, Didier Huin, Pascal Gardin

"With the aim of controlling steel grade in steelmaking reactors, IRSID and IMFT are developing a numerical description of the evolution of bubbles in the vicinity of a liquid steel/ slag interface. The objective is to identify the main parameters affecting the hydrodynamics of the various phases. The goals of the present paper are:• To describe the numerical technique developed to predict the multi phase flow including bubbles, liquid metal and slag layer.• To analyze the influence of the absolute pressure on the bursting of bubbles in a RH degasser. Validation is given by comparison with results available in the literature. The major point concerns the distinct behaviors observed whether the pressure is low or high.• To study the influence of the properties of the slag layer (thickness, viscosity and interfacial tension) on the entrainment of liquid metal in the wake of the bubble and on the nature of the projections from the bath surface.IntroductionMost of secondary steelmaking processes use gas stirring for homogenization, removal of nonmetallic inclusions or decarburization under reduced pressure. The bursting of gas bubbles at the metal or slag layer surface produces a beneficial ejection of metal droplets in the low pressure atmosphere, provided that there is no violent projection, which may have detrimental effects on the process.Our objective is to develop a numerical tool to study the phenomena occurring in the vicinity of the bath surface, in particular bubble bursting under reduced pressure and entrainment of metal in the slag layer. In this paper we report the first conclusions of our study. In the first section we describe the numerical model used to describe the three-phase flow and the expansion of the gas bubbles under the effect of the ferrostatic pressure. The second section is devoted to the study of pressure effects on bubble rise and bursting. The third section reports some computational results about the rise of a gas bubble through the interface between the two liquids."

Jan 1, 2001

By Harry Verakis, Thomas Lobb

In the past decade, approximately 5 billion pounds of explosives were used annually in the United States. Most of this quantity of explosives was used by the mining industry and coal mining was the dominant application for explosives. Considering the large amount of explosives used, the accident safety record for the mining industry has improved significantly over the past two decades. Blasting accidents are usually a small percentage of the total number of mining accidents. However, blasting accidents continue to occur and the severity of these accidents is disproportionately high with respect to other types of mining accidents. This paper is a summary and an update of the surface mine blasting accident investigations and studies conducted previously by the Mine Safety and Health Administration (MSHA) and the former U.S. Bureau of Mines.

Jan 1, 2001

By Neil Hepworth

Neves Corvo Mine employs four mining and four backfill methods, including paste fill. The paper shows how the strength requirement for backfill in primary stopes was calculated and the relationship between laboratory strength and in situ strength requirement. The liquefaction of paste in secondary stopes is discussed with methods to determine the liquefaction potential. It was found from laboratory tests and the preliminary results of the underground trial, that the liquefaction potential of the paste is low at 2% and is high at 0.5% cement. The results to date are inconclusive regarding 1% cement.

Jan 1, 2001

By R. Padilla

The reaction of chalcopyrite with gaseous sulfur has been investigated in the range 350-450 °C in order to transform this mineral into a more acid soluble copper sulfide and insoluble iron sulfide. The results of thermodynamic analysis of this system as well as the X-ray diffraction analysis of the reaction products showed that in the temperature range 350 400°C the sulfidation reaction proceeded without formation of intermediate copper-iron sulfides according to: The effects of temperature and time on the conversion of chalcopyrite were studied. Conversion of chalcopyrite reached about 80% very rapidly with increase in temperature up to about 400°C. The recovery of copper from the sulfidized samples was determined by leaching in oxygenated 1.2M H2S04, 2M NaCI solution. Copper recoveries over 90 % were obtained from samples sulfidized for 30 min at temperatures lower than 400°C.

Jan 1, 2001

By R. Colás, A. Salas, M. P. Guerrero Mata, R. Garza

"The use of the finite element method (FEM) for studying the plastic behavior of metals has become a common practice over the past few years, because it has been proved to be a good means of evaluating processes parameters, and predicting and improving processes, avoiding the traditional trail and error technique. FEM was used via a commercial package (Abaqus) to create two dimensional models to simulate uniaxial tensile tests for a galvanized low carbon steel. The aim of the work was to analyse the plastic behaviour of a distribution of grains on the zinc cover of a set of galvanized low carbon steel samples. A mesh with lines 2 mm apart was drawn on one of the faces of the samples that were deformed at room temperature, at constant crosshead speed, stopping the deformation at different times. Before and during the stops the deformation measurements were recorded for further calculations in an image analyser in order to compare these with computational predictions, as well as validate the numerical model. The results of this study can be extended to other testing conditions, besides the model can be used for obtaining constitutive equations of the materials.INTRODUCTIONThe use of the finite element method has been widely spread during the last two decades in most engineering areas, it is a good means of obtaining approach values at a first try [1-4]. Thanks to the software and hardware developments it is now possible to run huge problems within hours or minutes, making the technique more accessible and useful for the industry.The aim of this work is to create a finite element model for the uniaxial simple tension test, and compare the results with some experimental results, and asses the validity of the model.The plastic behaviour of the materials with FEM has been studied for a long time [5] and there is always something new to learn about this behaviour of the metals in particular, as well as to characterized new materials and alloys [6,7]. The tension test has been used since XIX century to get knowledge of the materials [5,8], it is the test that has been used the most and the only that is fully standardized, although it has the limiting of low strains, it is still the most widely used, especially in the industry.Two different finite element models in two dimensions (2D) have been developed, one called the mesh model and the other one the grain model, attention was focused on the geometry and strain prediction. The model is validated with experimental test, by using the data and directly comparing it with the numerical predictions. All the tests were carried out at the same constant crosshead speed at room temperature. An analysis of the grid distortion using FEM and analytical methods has been carried out."

Jan 1, 2001

By John Popovich

The MICON RokLok binder system including component and consolidation processes and safety and its first aide are described. The implementation procedures and selection of injection parameters are discussed. Finally a case example of recovering a 30-ft. long roof fall in mainline haulage entry is used to illustrate the economic potential of preventive measures by RokLok injection.

Jan 1, 2001

By J. C. Potvin

Although the occurrence of deposits of titanium minerals on Kenya’s present day beaches and adjacent dune systems has been well documented, the potential for older formations to host economically viable deposits had not been recognised until recently. The Magarini sands formation in Kenya has been found to contain deposits of ilmenite, rutile and zircon in quantities and grades that have the potential to be commercially exploited. Since 1995, Tiomin Resources Inc. has explored these deposits and has identified one deposit, the Kwale project, as being able to support the development of a mine producing some 300,000 tpa ilmenite, 75,000 tpa rutile and 37,000 tpa zircon. Tiomin plans to start production by late 2002. Construction of a US$137 million operation is set to commence in the first half of 2001.

Jan 1, 2001

By K. Noda

Tamano Smelter of Hibi Kyodo Smelting Co., Ltd. started its operation adopting the Flash Smelting Furnace with Furnace Electrodes (FSFE). Thereafter, it developed a coke combustion technology based on C() concentration control, which made possible a low cost and high productivity operation without using electrodes. However, increase of treated concentrates and upgrading of matte grade for production expansion started to cause difficulties in operation control with then existing operation control system. This paper outlines recent improvements for stable operation of the Tamano Type Flash Smelting Furnace (T-FSF), such as computer aided operation guide system.

Jan 1, 2001

By Raymond W. Henn, Kent A. Pease, Glen J. Rorison

The paper focuses on construction of a 2.55-km (8,365-ft) long, 2.4-m (8-ft)diameter storm drain tunnel in Evansville, Indiana. The tunnel was driven through saturated soft ground varying from clay to fine sand. The paper presents: an overview of design and design rational including specific EPB machine requirements; the contractor’s proposed and accepted alternative construction methods and TBM design; and construction issues and performance. Some of the key points discussed are the use of the TBM in different operational modes for alternative ground conditions, the effectiveness of dewatering systems, production rates, and issues such as surface settlements and gas.

Jan 1, 2001

By Remo Grandori

The Umiray Angat 13,2 km long tunnel in Philippines have been bored through extremely variable and difficult ground conditions including a number of special events. In particular the following adverse conditions were found: faults in decomposed ground, high temperature rocks, extremely rapid and important convergence phenomena, water inflows up to 800 litres per second. The special El Nino climatic conditions caused a long dry season and lower the level of the lake that was granting the access by barge to the site under the minimum navigable level. Many equipment have had therefore to be transported to site by a 10 ton capacity helicopter, after having been partially dismounted. For the same reason most of the tunnel drive have been bored servicing the site by 1 ton capacity helicopters to transport materials, spares and personnel. In order to overcome the above geological and logistic problems several innovation were introduced and tested in this project. Despite all that difficulties the 13,2 km of tunnel were bored in about 24 months, with a global average of 500 m/month.

Jan 1, 2001

By M. J. Price

The usage of Geographic Information Systems (GIS) is increasing rapidly throughout the Mining Industry, especially in the Industrial Minerals sector. GIS provides an efficient and robust link between spatial (often CADD) and tabular (database/spreadsheet) components. Mineral economists and corporate planners employ GIS to perform market analyses, to source raw materials, and to schedule and monitor deliveries to customers. Exploration and acquisition groups apply spatial analysis to identify high quality resources that meet economic guidelines. Mining regulators and environmental affairs departments expedite and monitor permitting, environmental compliance, and best management practices reclamation through GIS data management and Electronic Permitting. Operations staffs monitor overburden removal, material extraction, quality control, and stockpile volumes with GIS. This paper summarizes the many aspects of GIS in Industrial Minerals. It also introduces and addresses issues and concerns commonly encountered during a mining GIS implementation.

Jan 1, 2001

By Mark R. Jolly, Jean-Christophe Gebelin, Aleksander Cendrowicz

"Injection of wax patterns is the first stage of the multi-stage process of investment casting. The quality of the final casting and its dimensional accuracy is highly dependent on this stage of the process. Pattern waxes used in the industry behave in a complex visco-elastic-plastic manner. The modelling of such material behaviour is therefore not simple.In this paper a number of configurations of die will be shown in which the injection of the wax has been carried out for a range of processing conditions. Some of the dies are transparent and the movements of wax front observed can be compared with those predicted by simulation. Surface defects in final components will also be shown and compared with the location predicted by simulation software. Some discussion will be presented on the limitations of the software used and the time-scales achieved for practical use as a design tool within the foundry environment. IntroductionThis paper presents the research activities carried out at the University of Birmingham on the modelling and prediction of the behaviour of industrial investment casting waxes during the injection of wax patterns. These research activities are done in the context of a more global study of the fundamental aspects of the investment casting process, the FOCAST project. Regarding the wax injection process, the aim of the project is to achieve a better understanding of the key factors that will lead to better castings. The filling of the die during the injection has been studied. Some other phenomena such as shrinkage/warpage or creep under residual stresses are also studied, but not presented here. Two commercial investment casting waxes have been characterised in order to model their behaviour and predict mould filling and subsequent defects.This paper will present the models that have been used in our work, the simulation packages used, the experiments carried out to validate the modelling and exhibit the defects due to bad filling, and finally the numerical simulation results."

Jan 1, 2001

By D Pastars, J L. Mauk

Located at the southern end of the Awhitu Peninsula, the Waikato North Head ironsand mine is approximately 50 km southwest of Auckland . The ironsand deposit consists of Quaternary sands, clays and peats, formed by aeolian and marine processes. We sampled on widely- and closely-spaced intervals to test variability within the mining area. X-Ray powder diffraction shows that samples contain feldspars, quartz, pyroxenes, amphiboles, clays and titanomagnetite. Densities range from 1.6 to 2.5 grams/cubic centimetre, with porosities from 30 to 43 percent. The percentage of magnetic minerals values range from 0 to 75 percent, slimes (clay minerals) values of 0 to 26 percent and non-magnetic minerals from 20 to 95 percent. Mineralogical differences in the Mitiwai Formation and Waiuku Blacksand Member cause bimodal populations in the density, magnetic minerals, nonmagnetic minerals and slimes plots. The Mitiwai Formation has higher non-magnetic mineral values and lower density, slimes and magnetic mineral values than the Waiuku Blacksand Member.

Jan 1, 2001

By Rob Farnfield, Yuill Gavin

The rock blasting industry continues to be under pressure to reduce the level of vibration induced by the use of explosives. In recent years much research and development has been directed to minimizing vibration levels by controlling the delay period between blast holes. The most commonly applied technique is known as Linear Superposition. This technique takes the vibration produced from a single-hole test shot and simulates the vibration that would be produced from a full-scale production blast. The simulation can be run with various delay periods and the optimum delay chosen. The success of the Linear Superposition technique depends to a great extent on having accurate delay detonators and on the single-hole test shot reliably indicating the vibration signal produced from each hole in a production blast. A quarry-based case study is given illustrating how these assumptions are not always valid. In this case the use of electronic detonators has controlled frequency but not vibration level. The paper goes on to describe a series of single-hole test shots in an U.K. limestone quarry. The vibration 2 signals recorded are examined in terms of variations in free-face provision, blast geometry, explosive properties, etc.

Jan 1, 2001

By Jon Y. Kaneshiro, Ed Walton, Stephen J. Navin, Robert M. Sergeant, Storer J. Boone

The Coronado Traffic Tunnel is a proposed two-lane, reversible, road tunnel, which will relieve severe peak hour congestion problems on surface streets. The tunnel will take traffic from the Coronado Bay Bridge to Naval Air Station North Island. The project will include 12.5 m (41 ft) inside diameter by 1,112 m (3,650 ft) of tunnel, 552 m(1,815 ft) of cut and cover box structure, and 400 m (1,315 ft) of open cut structure. The geology consists of predominately clean and silty sand, saturated sand, with some clay layers, requiring Earth Pressure Balance or Slurry Shield tunneling technology.

Jan 1, 2001

By James A. Warren

The phase field method has been successfully employed as both a tool to model heterogeneous materials and as numerical method for calculating the motion of interfaces and phase boundaries without explicitly tracking those interfaces. The method has been used to model a diverse suite of problems describing the microstructural evolution in materials. These models are derived from thermodynamic arguments and symmetry principles, and usually guarantee positive local entropy production for systems out of equilibrium. Descriptions of how phase field methods can be applied to the problems of solidification, grain growth, and electroplating will be presented.

Jan 1, 2001

By P. Katsabanis

Numerical modelling was used to examine damage in wall control operations. Decoupled charges appear to create larger damage zones than fully coupled low density charges with similar charge distributions: Air was shown to be a very efficient coupling medium, while water coupling resulted in significant damage. However, Mach stems are formed when air is used as a decoupling medium, leading to compression of the charge ahead of the detonation wave. Air decked charges generate two damage zones, one close to the charge and another close to the air-deck/stemming interface, where pressure pulses are reflected. The extent of the latter depends on the length of the air-deck.

Jan 1, 2001

By A. S. Macfarlane

The introduction of new technology into mining operations is seen as a strategic necessity by many mining companies, in order to improve safety and to improve operational effectiveness. Many attempts have been made in recent years to introduce new technologies into mining operations in southern Africa. Amongst these are noteworthy successes, as well as some disappointing failures. Often, the reason for failure does not lie with the technology itself, but with the work system into which the technology is introduced. Such failures may come with a significant opportunity cost, and have a detrimental effect on future development, simply because the system has not been adequately engineered, and the risks have not been adequately assessed and managed. This paper examines the reasons for such failures, and proposes a methodology to be followed to ensure successful and sustainable implementation of new technologies, such as to reduce technical and financial risk to the company, and to energize the workforce into ensuring the initial objectives of the project are met. The paper also focuses on the application of appropriate technology, and the development of technological applications which are commensurate with the level of development of the work environment into which it is introduced. The paper therefore focuses on the application of risk management, change management, systems engineering and feasibility analysis as being key elements of a successful and holistic technology implementation programme.

Jan 1, 2001