Search Documents

By T. Ruben

Micropiles have been used for the last forty years to strengthen building foundations. This article gives information about the technology and capacity of micropiles.

Jan 1, 2000

By Pierre Pelletier, Christian Pichetie, Dany Pelletier

"IntroductionDuring 1994, Barrick Gold Corporation, or American Barrick at that period, acquired Lac Minerals Ltd. properties. One of them was the Bousquet Complex. The Bousquet Complex is divided into three distinct sites: one mine (Bousquet 2), one mill (Est-Malartic Division) and one analytical chemistry laboratory (Les Terrains auriferes).The Bousquet 2 orebody was discovered in 1986. An extensive drilling program was initiated during 1987. Its purpose was to define the orebody extent. At the end of 1997, gold production from Bousquet 2 mine reached 1 290 000 oz of gold from a cumulative tonnage processed of 4 175 000 M t.From 1980 to 1990, the Est-Malartic mill was used for the treatment of ore from the following mines: Bousquet 1, Doyon, Francoeur (Richmont mines), Buckshot and 1-20 stope. At present, the mill receives ore from the Bousquet 2 mine.HistoryThe Est-Malartic mill is located close to the town of Malartic in northwestern Quebec. The mill has been in production since the mid-1930s processing mainly clean, free mill gold ore. Active mining from the Est-Malartic mine ceased in 1979 and the mill was switched to custom processing of ore from La Mine Doyon located some 45 km to the west. This custom processing arrangement continued until 1987 when the expanded mill at Doyon became available to process all of the Doyon production. In 1987, Lac Minerals commenced development of a second mine at the Bousquet site located 40 km west of Malartic. This mine, Bousquet 2, is the down dip extension of the La Ronde mine developed by Agnico Eagle. During pre-feasibility evaluations, it was determined that it would be economically more attractive to modify the existing Est-Malartic mill than building a new facility on site. The Est-Malartic mill modifications for processing the high-copper/gold ore from the Bousquet 2 mine began in late 1989 and new circuits were commissioned in mid-1990. Modifications included the addition of both gravity and flotation concentration circuits to recover coarse, free gold and the copper. The existing leaching circuit continued to operate on the copper flotation tailings with some minor modifications to the solution handling systems. A S02/Air cyanide destruction circuit was also added at that time."

Jan 1, 2000

By R. R. Oder, R. E. Jamison, E. D. Brandner

This paper presents preliminary test results obtained with a 0.38 kg/s (3000 lb-hr) beta prototype MagMill™. In processing Upper Freeport coal the beta prototype recovered 82% of the weight of the feed and 91% of the heat content while reducing the potential emissions of sulfur, kgSO2/GJ(lbSO2/MBtu), by 61%. Pyritic sulfur in the MagMill™ product was reduced by 78% compared to that in the feed. For all runs, the mill product was controlled between 70 to 80% finer than 74 µ particle size. Recoveries of mercury, arsenic, and selenium ranged from 35 to 45% of that in the feed. Power draw was reduced by 26% and mill throughput was increased by 9% compared to the pulverizer operating with no magnetic separator attached.

Jan 1, 2000

By Takeshita. Takuo

"In this work, the progress of the HDDR process is discussed mainly on the Nd-Fe-B magnet system. There are three technologies being used for the Nd-Fe-B permanent magnet production; the sintering technique, the rapid quenching annealing and the HDDR process. The HDDR process utilizes· the HDDR phenomenon, in which hydrogen absorbing intermetallic compounds go through as they are heated in hydrogen atmosphere, Hydrogenation - Decomposition Desorption - Recombination. In the HDDR process, these four steps in the HDDR phenomenon are processed by choosing suitable reaction conditions regarding to hydrogen gas pressure, temperature, rate ·of desorption and etc., and we can produce permanent magnet powders of good magnetic properties with microstructures consisting with sub-micron size crystalline grains. In the anisotropic magnet powders, the sub-micron size crystals are being mostly aligned in the crystallographic c-axis direction. Possible applications of the HDDR process to other systems are also discussed.Microstructures of the Nd-Fe-B Permanent MagnetsIt is well known that magnet properties of magnetic materials are very sensitive to their microstructures [l]. This is seen in almost all magnet materials from soft magnetic materials and hard magnetic materials to magnetic memory materials. In this regard, the production technology is very important for the control of microstructures of permanent magnets The Nd-Fe-B magnet is the most powerful permanent magnet as a practical permanent magnet, and its coercivity force is much dependant on the microstructure as is the case for other permanent magnets."

Jan 1, 2000

By D S. Stewart, K W. Keskimaki

The Henderson Mine has been utilising a continuous panel caving method to extract molybdenum ore since starting operation in 1976. In the past three decades since the mine was designed, many changes have taken place in underground technology as well as the general nature of the mining business. The impacts of larger scale underground equipment and automation are significant at Henderson and continue to reshape the nature of the enterprise. During the first years of operation in the 1970s, Henderson required almost 2000 employees to achieve full production, today only about 400 people are required to fully utilise the plantÆs capacity. The most recent change to the facility is the conversion from a rail haulage system to an underground crushing and conveying system that transports ore 25 km to the Henderson mill site. This change has required the introduction of large, rubber tired haulage trucks underground and the mining methods necessary to develop the large openings demanded by the trucks and underground crusher. The development of the underground crusher is also the first step to mining the final bottom horizon of the orebody. Along with this move comes an opportunity to almost triple the effectiveness of the mining effort, through higher draw columns and wider draw bell spacing. This final advancement to a totally trackless mine has positioned Henderson well for safe and efficient operation as it enters the 21st century.

Jan 1, 2000

By W C. Burton, J S. Kuszma, T O. Aspinall

The environmental impact of mining and evolving environmentallegislation has received increased attention worldwide in the last two decades (Bradfield, Shultz and Stone, 1996). The potential impacts associated with unstable spoil dumps from mine operations is the focus of concern both by the mining industry, environmental regulatory agencies and members of the public. Engineered slopes of mine spoils may be stable at the end of construction, but they can deteriorate over time. There is thus the need to increase the base of knowledge on the existing practices of spoil dump design and rehabilitation. Efficient engineering design and systematic economic evaluation of spoil dump reshaping techniques for mine rehabilitation assists in maintaining the expected standards of environmental compliance. As part of the overall approach for effective engineering design ofspoil dumps, a comprehensive, computational and efficient tool isrequired for assessing the economics and productivity of existing spoil dump reshaping practices for efficient mine rehabilitation. Such a design tool is useful in linking current spoil dump environmental management practices with engineering design planning and economic impact evaluation. This paper identifies the processes for the economic impact evaluation for existing spoil dump reshaping practices and proposed final site dump designs. Selection of an efficient spoil dump design at optimum costs will ensure operational efficiency. A case study is presented identifying economic impact evaluation in earthmoving equipment selection and the costs involved for the reshaping of spoil dumps to that of varying final site designs.

Jan 1, 2000

By Martin J. Pedley

The use of soil nailing has grown steadily in the UK over the last 15 years and it has recently become more popular in the Republic of Ireland. This paper presents three soil nailing temporary works case histories where the technique has been used to support steep excavations in difficult ground conditions. It demonstrates the effectiveness of soil nailing when applied in appropriate conditions. Details of design methods and construction techniques are described and those aspects of soil nailing that will benefit from further study and development are identified.

Jan 1, 2000

Your assessment of the minerals business. The global mining industry is strong. I am convinced it will continue meeting the mineral needs of the world population for the foreseeable future. Two developments have greatly enhanced the industry’s ability to produce low-cost minerals. Technological innovations have resulted in increased productivity. And there has also been a dramatic expansion of the number of favorable countries in which to explore and mine. Capital expenditures have flowed to the low-production-cost mines and development projects as well as to the exploration projects and stable countries having the best potential for valuable mineral discoveries.

Jan 1, 2000

By H. D. Van Veldhuizen

The Multilateral Investment Guarantee Agency(MIGA) is part of the World Bank Group, and has as its mission the facilitation of foreign direct investment by providing political risk insurance (guarantees) to foreign investors and lenders. As a development institution, MIGA is required to ensure that the projects that it insures will bring development benefits to the host country. Demonstration of this includes review and analysis of the environmental and social soundness of a prospective investment. Environmental guidelines and policies developed by the World Bank Group are important components both in analyzing the environmental and social soundness of a prospective investment and in risk management. MIGA has recently formalized and adopted environmental assessment and disclosure policies. The approach taken by MIGA to environmental review of investments and implementation of these policies is described in this paper.

Jan 1, 2000

By Neng-Wen Yu, Miao Wang, Ji-He Wei

The mass transfer characteristic between powder particles and liquid steel in the RH-PTB (Powder Top Blowing) refining has been investigated in a water model of 1/5 scale for a 90t RH degasser. The sodium chloride powder with analytical purity has been used as the flux for blowing. The mass transfer coefficient of the liquid side has been determined under the conditions of RH-PTB process. The influences of the main technological and structural parameters on the mass transfer rate have been examined. The results indicated that under the conditions of the present work, the mass transfer coefficient on the liquid side increases with raising the lifting gas blowing rate, inner diameter of the up-snorkel, circulation rate of the liquid and particle size of powder flux. And it decreases with an increase in the inner diameter of the down-snorkel. It is in the range of (l.36-7.30) x 10·4 mis, the appropriate dimensionless relationships have been obtained as follows:

Jan 1, 2000

By Ray D. Peterson, Annette Revet

The optimization of secondary aluminum furnaces is critical to the efficient operation of a recycling facility. Since all metal loss occurs in the drosses, physical and chemical analyses of these by-products are valuable diagnostic tools. Dross analyses can provide information concerning total furnace metal recovery efficiency as well as identifying areas for potential improvements. A complete dross analysis is a labor-intensive process that requires significant care both in sampling and performing the analytical techniques. Experiments can be done at a bench- or plant-scale depending on the facilities available. This paper outlines the benefits and information that can be generated through dross studies. Furthermore, several analytical methods are discussed as well as the special requirements needed to gain accurate results. Experimental data from industrial studies is provided to demonstrate the use of dross evaluations for ~ace optimization.

Jan 1, 2000

By Mark R. Svinkin

Construction vibrations may be harmful to adjacent and remote structures, sensitive instruments and people. Construction vibration sources have a wide range of energy, displacement, velocity and acceleration transmitted on the ground. Effects of different dynamic sources and soil conditions on construction vibrations is analyzed. Consequences of construction vibrations are developed in various ways. It is important to assess intolerable vibrations before the beginning of construction activities. Guidelines for preconstruction survey are presented. Pre-construction survey and prediction of anticipated vibrations by IRFP method, monitoring and control of measured vibrations are important steps in preventing intolerable vibration effect.

Jan 1, 2000

By R. L. Howell, L. C. Atkinson

Typical sedimentary sequences overlying coal seams consist of interbedded sandstones, siltstones, shales, and rider coal seams. In many surface coalmine settings, these sediments are saturated; and prior dewatering of them is necessary for effective and economic mining, including the stacking of saturated spoils. Such sedimentary sections usually have a very low vertical hydraulic conductivity that does not allow them to drain in a timely manner prior to their being stripped. One potential solution is installation of drainwells. Drainwells are small diameter wells that can collect water laterally from the various more permeable layers in the overburden and then gravity drain it to a lower layer – often the coal seam being mined – where it can be removed by pumping wells or sumps located in the bottom of the pit. A ground-water flow model utilizing the 3-dimensional finite element code MINEDW has been used to evaluate the effectiveness of usingdrainwells in a hydrogeologic setting that is typical of the Powder River Basin. A series of numerical simulations were completed using various combinations and spacings of drainwells and pumping wells to dewater the overburden and coal seams. The numerical simulations suggest that drainwells can be a very effective method of overburden dewatering.

Jan 1, 2000

By S. de Vries, B. Wasmund, J. Metric, N. Voerrnann, S. Kasinger

Gulf Chemical & Metallurgical Corporation (GCMC) operates a circular DC electric smelting furnace to treat nickel and cobalt bearing residues at its plant in Freeport, Texas. The furnace, originally built by others, has experienced problems including runouts through the hearth and the lower sidewall. Hatch has designed several improvements to the furnace to alleviate these problems. The single anode at the centre of the hearth was replaced with a patented system of twelve air-cooled copper anodes evenly spaced around the furnace lower sidewall. The DC power supply comprises two transformers and two rectifiers operating in parallel. The water-cooling system on the bottom and lower sidewall shell plates was replaced with an air-cooling system using copper cooling fins. The existing row of water-cooled copper coolers in the metal bath zone was re-designed for greater heat removal capacity and better element joint sealing, and a new row of water-cooled copper coolers was added to cool both the alumina bath and freeboard zones. The existing water-cooled metal and alumina tapblocks were also re-designed for more robust cooling. A binding system was added to provide refractory compression that reduces the risk of liquid leaks. Finally, the furnace tilting frame was relocated to the top of the furnace where it is less likely to be damaged.

Jan 1, 2000

By C. W. Benjamin

The paper covers the development of an efficient, "state-of-the-art" design approach encapsulating extensive research and development by Gulf on soft loading, low impact, zero spillage transfer chutes. The development, which interacts and interfaces the comprehensive methodologies for transfer chute design, allows Gulf to deliver detailed designs within 8-24 hours rather than the norm which is weeks or months. Outputs include 3D models of completed transfers and support structures along with rendered 3D representations of the design which can be fully manipulated around all axis in 3D.

Jan 1, 2000

By M F. Lee

Although the Mt Charlotte gold resource was discovered in 1893, it was only in 1954 that geologists correctly interpreted drill data and defined a large low-grade orebody. The mine has been a large, low-cost and profitable producer since 1962 when bulk mining commenced using cut and fill. From 1968 a combination of long hole open stoping with delayed mass blasting was used. This proved to be an excellent mining method for the large, separate subvertical orebodies. The structured but otherwise good quality rock allowed very large stopes to stand unsupported. Exceptionally large equipment, for its time, was used to efficiently mine, muck and move the ore at low-cost. The mine only just survived severe cost pressures in 1974-76, due to very low gold prices. Better gold prices in 1979 and a need to access deeper ore meant a bold commitment to sink the Cassidy Shaft and refurbish the mine to sustain future profitability. In 1997 the Sam Pearce Decline connected to the underground workings, making it profitable to mine upper level remnant ore. Mining-induced seismicity has been a feature of mining at Mt Charlotte. The main cause has been shearing on structures. A mine-wide seismic system was installed in 1994. Large seismic events have occasionally made management question whether a safe working environment can be maintained. Thorough investigations led to an understanding of the problem and development of procedures to minimise seismicity.

Jan 1, 2000

By R. L. Grayson

Focusing on relationships between severity measure versus productivity and other factors, this paper presents a comprehensive study of injuries for U.S. underground coal mines in 1996 by mine size. Based on analyses of data, generally the larger the mine, the more productive it is (in tons per employee-hour), but the more severe is its injury experience (r = 0.65). Within very large, large, and medium mine sizes, however, the more productive the mine, the less severe is its injury experience (r =-0.43, -0.36, and -0.26, respectively). For small and very small mines, a more deeply nested analysis is required to understand relationships. Other interesting relationships and comparisons are presented.

Jan 1, 2000

By D. N. Wilson

The potential risks of working with lead have been recognised for centuries, but it is only with the development of sensitive measuring techniques in relatively recent years that it has been possible to establish effective approaches for the monitoring and control of lead exposure. This paper examines the principal control measures employed today - lead in air and lead in blood - and reviews the evolution of numerical standards, with particular reference to the latest understanding of health effects. In addition to lead, a large number of other metals are commonly encountered when producing lead and zinc - both primary and secondary - and the health effects of many of these are discussed. Modern hygiene practices and technologies, which have proved successful in reducing worker exposures, are reviewed. The paper concludes with a look at how exposure standards are likely to change in the near to medium future

Jan 1, 2000

By Garry Biles

The Eskay Creek Mine is a high-grade gold and silver underground mine in northwestern British Columbia. The mine started operations in late1994. For the first three years, ore was crushed to -50 mm(-2 in.), blended to satisfy smelter terms and shipped to smelters in Japan and Canada. Preliminary evaluations indicated that a complex metallurgical facility, requiring a large capital investment, would be required to recover the precious and other economic metals. So markets for raw ore were identified and underground mining and ore transportation operations began at a production rate of 300 t/d (330stpd).

Jan 1, 2000

The more than 40,000 mining industry professionals that are expected to attend the National Mining Association’s(NMA) MINExpo International2000 trade show and conference will be treated to the exhibition’s largest display ever. The exhibit is expected to cover more than 60,385 m2(650,000 sq ft) and feature more than 1,300 exhibitors. The event is set for Oct. 9-12, 2000 at the Las Vegas Convention Center in Las Vegas, NV. Richard L. Lawson, NMA’s president and chief executive officer, said, “MINExpo 2000 will showcase everything that mining is proudest of. This is the largest premier mining exposition in the world.” MINExpo is held every four years.

Jan 1, 2000