Search Documents

By Steve Kral

Through advanced technology and innovative thinking, the mining industry has become one of the world’s leading industries in environmental protection. But it only takes one Summitville, Omai or, most recently, the Aurul gold tailings retreatment operation in Romania to provide ammunition to the industry’s critics in their attempts to sway public opinion against mining. So for the mining industry to continue operating with the public’s support, it must continue to improve its tailings waste-disposal processes and the dams that hold this waste. In January, about 120 specialists in the mine waste management field gathered together to discuss the available technologies and materials for controlling mine waste and mill tailings disposal. “Tailings and Mine Waste’00” was held at Colorado State University in Fort Collins, CO. This meeting, begun in 1978, is a continuing symposium. It provides a forum for environmental professionals to discuss the state-of-the-art in mill tailings and mine-waste disposal methods.

Jan 1, 2000

By Masayuki Kudoh, Kiyotaka Matsuura

"Molten aluminum and nickel cast onto a steel block exothermically react and produce molten nickel monoaluminide, NiAI, which is simultaneously joined to the steel. The heat of the exothermic reaction is transferred to the steel block, and steel near the surface of the block is melted. The depth of the melted steel increases with both the initial temperature of the steel block and the thickness of the produced NiAI. Iron from the melted steel dissolves in the molten NiAI, and an intermetallic compound of NiAI-Fe pseudo-binary system is produced. During solidification of the intermetallic compound, it is strongly joined to the steel. The Ni.Al-Fe intermetallic compound has an excellent resistance to oxidation and corrosion.IntroductionAn intermetallic compound of nickel monoaluminide, NiAl, offers many advantages over conventional superalloys, such as higher melting temperature, lower density, greater specific modulus and higher thermal conductivity [1]. NiAl also exhibits excellent high-temperature oxidation resistance when doped with zirconium or hafnium, and excellent high-temperature corrosion resistance when doped with chromium or yttrium, that are superior to existing high temperature alloys or coating materials [1-4]. On the other hand, NiAI is significantly brittle at temperatures below 600 K [5-7], which is the most sigriificant disadvantage of NiAI. A possible way to overcome the disadvantage and to utilize NiAl as an environmental-resisting high-temperature structural material may be joining of NiAl to a ductile material."

Jan 1, 2000

By Wade L. Karlsen

"Revision surgery to replace joints in the human body requires materials that are strong, long-lasting, and biocompatible. Metallic implants made of cobalt-chromium-molybdenum alloys are already popular because of their proven corrosion and wear resistance properties, but there is an on-going effort to economically improve their performance. Alloying with inert nitrogen can enhance the mechanical properties of the alloy, enhance its corrosion resistance, and elevate the temperature at which the metallic implants can be thermally treated, without increasing the threat to the human body. The current work has produced a high-nitrogen Co-Cr-Mo alloy through HIP consolidation of metal powders that have undergone nitriding in a mechanically fluidized bed. The already fine microstructure of the powders combined with the increased nitrogen content resulted in significant property gains in the consolidated materials.IntroductionMetallic implants made of cobalt-chromium-molybdenum alloys are already popular because of their proven corrosion and wear resistance properties, but there is an ongoing effort to improve their performance. Research on a Stellite 21 cobalt-chromiummolybdenum alloy has shown that nitrogen alloying can be desirable from several standpoints [l]. Firstly, it has indicated that nitrogen can enhance the mechanical properties of the alloy, which could allow more demanding implant designs. The same work also demonstrated that nitrogen can elevate the temperature at which the metallic implants can be thermally treated, which is desirable in situations in which surface textures are to be sintered to the implant to enhance its fixation properties. Finally, that research work discovered that, not only does nitrogen not harm the corrosion resistance of the cobalt-chromium-molybdenum alloys, but it may in fact enhance it. Combining this with the fact that small amounts of nitrogen are not considered a threat to the human body, makes nitrogen alloying an attractive alternative for enhancing the properties of Co-Cr-Mo."

Jan 1, 2000

By Alun J. Davies

This paper describes a design-build project for the construction of a tanker wharf for 150,000 dwt vessels. The tankers deliver oil from offshore oil fields to a Transshipment terminal on the south coast of Newfoundland. The project described is an expansion to a previously constructed facility, adding an additional berth. The first berth was designed conventionally as concrete structures supported on groups of independent, single piles. The second berth was awarded to Peter Kiewit Sons' Co. Ltd. based on an alternate design which utilized a "jacket" concept whereby prefabricated steel frames are placed on the seabed and serve as permanent templates and also give lateral support to the piles, thereby increasing their load capacity. This led to economies and time savings. Discussed herein is the design process and the field installation, covering the jackets, driven pipe piles, and the rock anchors.

Jan 1, 2000

By T. Goda, H. Kiuchi, M. Iguchi

"IntroductionThe utilization of silver in the electronic industry has been increasing in recent years. It is desirable that valuable metals are recovered from the used scraps of these industrial goods. Condensor chips, for example, contain silver, palladium, and Ag-Pd alloy. The dissolution behavior of silver was studied assuming that scraps such as used condensor chips in which Ag-Pd paste is used are subjected to wet treatment.ExperimentalIn this study the powder, granules, and flakes of silver were used in these nitric acid leaching experiments. The nitric acid solution was agitated in a glass reactor with a magnetic stirrer and heated to the required temperature. The experiment was started by putting the silver sample in the solution. After the leaching, the solution was filtered and the concentration of silver in the filtrate was analyzed by ICP.ResultsIn dilute nitric acid of less than 5 N, silver powder dissolved easily with increase in the concentration of nitric acid and temperature. However, the more intensive the stirring of the solution was, the lower the dissolution quantity became. Fig. 1"

Jan 1, 2000

By Jaroslav Horskoý, Miroslav Raudenský, Bogdan Filipic, Božidar Sader

This paper describes main elements and practical use of the computational system for automated setting of optimized casting conditions in the continuous casting of steel. The system consists of the heat transfer model of the process, empirical metallurgical criteria, and optimization algorithm. The physical model of the, strand temperature distribution relies on the classical Bennon-Incropera mixture continuum formulation for the convective-diffusive heat transport. Fluid flow effects are considered through enhanced thermal conductivity of the liquid phase. The model is solved by the operator-splitting Crank-Nicolson finite volume version of the Voller-Swaminathan scheme. The solution procedure is coupled with the IDS solidification analysis package. Boundary conditions for the strand cooling rely on combination of the generic and plant-specific mold, spray, and roll heat transfer coefficients ' by coping the effects of the casting speed, casting temperature, casting powder, mold oscillation mode, steel grade, water or air-mist spray type, running water, trapped water on the rolls, and radiation. The caster safety and productivity and the quality of the strand are related to nine empirical metallurgical criteria. The criteria ensure the caster safety and economy as well limit the internal, longitudinal, and transversal surface cracking possibility. The problem of finding optimum casting parameter values is stated as a minimization problem based on the analytical form of the cooling criteria evaluated from the steady-state temperature distribution of the strand. To solve the optimization problem, a genetic algorithm is employed. The algorithm explores process parameters settings heuristically by applying the principles of biological evolution. It starts with a random set of solutions and iteratively improves them through selection and variation. Solutions are evaluated by running the heat transfer model of the process and extracting the values of the empirical metallurgical criteria.

Jan 1, 2000

By Toshihide Takenaka, Takashi Matsui, Nao Murakami, Masahiro Kawakami

"Electrowinning of Ti have been investigated in a LiF-NaF-KF melt including K2TiF6 at 773-923K by applying electrochemical oxidation ofH2 gas as an anodic reaction. The cathodic behavior of titanium and the anodic behavior of H2 gas were studied by voltammetry in detail to clarify the electrolytic condition for the process. The electrowinning of Ti was carried out by potentiostatic _electrolysis. Steady electrolysis was achieved under the suitable electrolytic condition without breaking out the anode effect. Titanium metal was electrodeposited on a Ti cathode though the deposits were usually powdery. It is concluded that this process is potential if the morphology of the deposit can be improved.IntroductionTitanium has such good properties as high specific strength and high corrosion resistance. However, the availability of Ti has been limited because the price of Ti is much higher than those of other common metals, such as Fe and Al. The production process of Ti ingot from its ore is rather intricate so that the production cost is high. If the simpler process is developed, the production cost should be retrenched. Titanium metal is usually produced by the Kroll process, which consists of the electrowinning of Mg metal in molten salt and the chemical reduction of TiCl.i by Mg metal. The Kroll process is very elabrate, but not simple. Because the chemical reduction ofTiCl4 by Mg metal is highly exothermic, a considerable amount of energy is wasted.Titanium metal can be electrowon in molten salt bath in principle. A simpler and more effective process than the Kroll process may be realized by the direct electrowinning so that the electrowinning of Ti metal has been studied widely[ 1]. Some researchs progressed to a pilot plant stages [2], but the electrowinning of Ti has not been industrialized yet."

Jan 1, 2000

By Norihiko Fukatsu, Takashi Iwamoto, Noriaki Kurita, Koji Katahira, Kunihiro Koide, Teruo Ohashi

"The galvanic cell-type hydrogen sensor employing CaZro.9Ino.t03-a. as the solid electrolyte was designed for the measurement of hydrogen activities in molten copper under industrial .conditions. The sensor probe consists of the cap-shaped solid electrolyte with porous platinum electrode on the inside and alumina refractory tube. The gas mixture of the composition 4%H2-0.5%02-Ar was made to flow on the inside electrode. The hydrogen sensor probe was inserted directly into molten copper and the melt was used as the outer electrode. The effect of oxygen activity gradient to EMF was eliminated theoretically by measuring the oxygen activity in the melt simultaneously with an oxygen sensor. The high stability of output and excellent response to the change of hydrogen activity were obtained over the wide range of industrial copper melting conditions.IntroductionIn the metal casting process, hydrogen easily dissolves in molten metals from water vapor in the surrounding atmosphere. Owing to the large difference in hydrogen solubility between liquid and solid metal, dissolved hydrogen becomes a cause of the defects of blowholes in castings or ingots. It is necessary to control the hydrogen content in the molten metals [l]. Using proton-conducting ceramics as a solid electrolyte, high temperature-type hydrogen sensor can be constructed [2]. SrCe03- and BaCe03-based perovskite-type oxides exhibit appreciable proton conduction under hydrogen containing atmosphere at high temperature [3-5]. A hydrogen sensor for molten aluminum using CaZro.91no.103-a. has been developed and widely used in the ·process control in the aluminum melting industry [6,7]. The same type of hydrogen sensor has also been expected in the copper melting industry. .. However, CaZro.91no.103-a shows ·not only proton but also oxide ion conduction in the high temperature and at low oxygen activies like the copper melting· conditions. Then we studied the oxide ion conduction in CaZro.91no.103-a. iit · detail [8]. From the consideration on the EMF of the galvanic cell employing this material as electrolyte, it was shown that the unknown hydrogen activity may be precisely determined from cell potential which is corrected for the effect of oxygen potential gradient And the hydrogen sensor based in this principle was constructed and tested in laboratory-scale [9,10]. We repeated the similar tests in factory-scale and developed the sensor system for practical uses [11, 12]. In this report, the structure and system of the hydrogen sensor for molten copper will be introduced first. The reliability of the sensor will then be demonstrated from the results of experiments for sensor probes carried out in TYK's laboratory."

Jan 1, 2000

Increasingly specialized blasting needs require that the explosive energy available in a borehole be reliably known for representative blasting conditions. The underwater test, when properly performed, can yield such information and thus provide a reliable rating of explosives in terms of energy release. This paper reiterates the stringent experimental conditions to be satisfied, and data analysis and interpretation techniques to be followed to achieve this. This is supported by detailed experimental studies involving select parameters in both detonator and booster sensitive explosive compositions. The paper also illustrates the inadvisability of equating blasting performance with the commonly calculated energy values.

Jan 1, 2000

By Leo Brewer, Kazuyoshi Shimakage, Mamoru Mitomo, Toshiyuki Nishimura, Yoichiro Uemura, Shinji Hirai

"In the synthesis process of ß -La2S3 via the sulfurization of La2O3 powder using CS2 gas, La2O2S was formed. This occurred at an initial stage of the reaction for sulfurization temperatures below 973K, and ß -La2S3 was also formed at a shorter period for higher sulfurization temperatures. It was found that the oxygen content in ß -La2S3 powders decreased gradually with an increase in sulfurization temperature. On the other hand, the carbon content in these powders increased gradually with an increase in the sulfurization temperature. Though it has been reported that ß -La2S3 was transformed to Y -La2S3 at 1723K± 50K, the sintered compact of double-phase Y -La2S3 and ß. -La2S3 was formed at a rather higher temperature of 1973K when the synthetic powder of ß -La2S3 containing a high amount of oxygen was used. However, phase transformation of -La2S3 to Y -La2S3 progressed preferentially with a decrease in the oxygen content of synthetic ß -La2S3 powder. The Seebeck coefficient of the sintered double-phase Y -La2S3 and -La2S3 was higher than that of the single-phase Y -La2S3, reported previously.Introduction La2S3 exists in three polymorphic forms that are similar to a series of Ce2S3, Pr2S3 and Nd2S3: a, ß , and Y'. The a -La2S3, which is stable at low temperature, is irreversibly transformed to ß -La2S3 of various compositions in the solid-solution range between La2S3 and La3S4, at 923 ± 50K. The -La2S3 may also be an oxysulfide of La10S14O2. Moreover, the ß .-La2S3 phase is transformed to Y -La2S3 ,which has a Th3P4 structure, at 1573 ± 100K. The melting point of Y -La2S3 is 2398 ± 30K where this temperature is similar to those of common refractory materials such as silica and alumina. Therefore, it can be predicted that y -La2S3 which has a high melting point and a thermodynamic stability due to the strong affinity of La for S, would have &high refractory character and chemical inertness in many molten metals. The y -La2S3, colored vivid faint yellow is stable up to 623K in air, where oxidation starts. y -La2S3 is frequently used as pigments for plastics and paints3. Furthermore, Y -La2S3 which is a semiconductor, is considered to be useful as a thermoelectric conversion materials, because it has a high Seebeck coefficient."

Jan 1, 2000

By Y. Ide, K. Kishitake

It is expected that an Al-Cr-N composite nitride film may have a higher resistance to oxidation at elevated temperatures than the well-known Ti-Al-N films. The formation conditions of Al-Cr-N films by a de reactive sputtering method and their properties were studied in this study. The films characterized with respect to their high temperature properties such as chemical composition, crystal structure, microhardness, wear and· friction. The crystal structure of the Al-Cr-N films changed from hexagonal phase to cubic phase with an increase in Cr content in the films. The resistivity to thermal oxidation of the Al-Cr-N films is superior to that of usual TI-Al-N films. A half of the friction coefficient in the Al-Cr-N film was obtained comparing with that in the ordinary TI-Al-N film at room temperature and the wear rate of Al-Cr-N film was 2 order smaller than that of TI-Al-N film. The Al-Cr-N films show a small friction coefficient at 500°C and then they are recognized to have good tribological characteristics.

Jan 1, 2000

By Hidefusa Takahara, Koichi Miyake, Dierk Raabe

"Mechanical properties of copper wires were examined. The copper wires containing 5-10 mass % chromium and 1-3 mass % silver were produced through heavily cold deformation. It was expected that the copper wire was easily fractured during cold deformation because of the existence of brittle chromium phase in the alloy. In fact, the copper wire was fractured due to large work hardening, when the true strain [n] exceeded 5. However, the copper wire annealed at 1273K for 6 ks ·in the middle of deformation process could be smoothly drawn to 11=8. After precipitation treatment for silver phase at 473k for 1.8 ks, the wire was able to further drawn to n=8.4. The final deformed wire showed tensile strength higher than 1200MPa.IntroductionDownsizing of electronic devices has led to the demand of finer and higher strength materials for cables. Conventional copper alloys have about 800MPa in ultimate tensile strength. These strength are mainly obtained by precipitation hardening. Nowadays, a process for higher strength wire has been developed, where dual phase copper alloy is used. When it is drawn heavily, the' second phase is elongated along drawing direction and the wire gets high strength due to fiber reinforcement (1). That alloy is so called in-situ formed fiber reinforced ·alloy. Cu-Ag(2), Cu-Nb(3) and Cu-Cr(4) systems are well known as such alloys. It is also well known that chromium is brittle material except single crystal and high purity of chromium. However, Mihara et al. C5l have achieved 1 GPa in ultimate tensile strength in the Cu-Cr-Zr and Cu-Cr-Ti alloys by appropriate thermo-mechanical processing.In this study, the Cu-Cr-Ag systems were investigated: The alloys contained 10 or 5% chromium and 3 or 1 % silver. It was demonstrated that silver precipitated in copper matrix contributed on further hardening."

Jan 1, 2000

By L. Ozdemir, M. Cigla

This paper presents and discusses some of the computer models developed and currently used at the Earth Mechanics Institute (EMI) of the Colorado School of Mines (CSM). These include the performance models for full and partial face machines. Examples of input and output of these models will be illustrated for typical mining operations by using machines such as Tunnel Boring Machines (TBM), Continuous Miners (CM), Marietta borer miners and longwall drum shearers. The general approach to modeling and the available models are discussed and some examples of these models are presented. The comparison between the estimated and achieved performance, as well as the degree of improvement in the performance due to balancing and modification in cutterhead design are also discussed.

Jan 1, 2000

By H. K. Fouad, L. A. Guirguis

The starting mill strip solution· for this study· is an ammonium uranyl tricarbonate solution of pH 8.2 containing 20g uranium/liter, after a DEPA/TOPO extraction process from sulfuric acid leaching liquor. To the first portion of the concentrated acidified strip solution, hydrofuoric acid is added at 95°C in reduced condition to obtain uranium tetrafluoride. The second portion of the uranyl carbonate strip is subjected to a precipitation step by admixing 0.3 volume of non-solvent precipitating agent such as acetone per volume of uranium. ·Uranium oxide (U30 8) is obtained from this precipitate by calcination for half an hour at 800°C in air. The third portion of the strip solution is neutralized to a pH 6.5 with sulfuric acid to precipitate iron and other contaminants. The solution is further acidified to a pH 1.85 with continuous air bubbling to remove CO2, followed by H2Ch precipitation at pH 3.5 to obtain uranyl peroxide. The latter is reduced by stannous chloride to obtain uranium trioxide dihydrate UO3. 2H20. Identifications, characterization· and purity of these products are carried out by complete chemical analyses, Scanning electron microscope study, tap density determination, X-ray diffraction and infrared spectroscopic investigations. The achieved results agreed well with that of the published data for these nuclear grade purity products.

Jan 1, 2000

By Kunihiko Takeda, Kimio Imaizumi, Tsuyoshi Arai

"The study on the preparation of mono-dispersed liquid droplet was performed using ultrasonic as one of the steps of producing the perfectly mono-dispersed particle. The ultrasonic system was a 33.6kHz ultrasonic generator, an amplifier, an electric distortion element, and a bolted Langevin type horn installed in .a cell. For the first time, a liquid pillar under a nozzle of the cell ·was stably formed. Then, dense and coarse parts were alternatively constructed by oscillating the wavelength of the ultrasonic.· The diameter of those liquid droplets were found to be· perfectly uniform, therefore, it was measured by ""multiplex photography"" using a synchronized stroboscope with the ultrasonic.- From the results, more than 30,000 of perfectly uniform liquid droplets in 1 second were observed by this method.IntroductionRecently, research on the control of physical form is done in various fields of industry. Some examples are the processing technology of the minute compound material of micro-machines and integrated circuits, and the form control of molecule size like catalysts. There is a need for such material to take on various forms in correspondence to its use. ""Form control"" as used in this study will indicate ""research on physical chemistry factors which determine the size of the material"" and will refer to the contour uniformity of comparatively little particles. A well-known method of preparing particles is to spout a mist of liquid and slurry from a nozzle l) 2). Particles for metals, catalysts and food have been prepared by this method. In this case, although an approximate particle diameter can be decided by controlling the nozzle diameter and the violent outflow velocity, it is not easy to completely control ·the contour and to prepare a particle with uniform diameter. ·However, the preparation of perfectly uniform particles is necessary for solders for the adhesion of electronic wiring 3), ion exchange resins4), catalysts and so on. Large quantities of fine particles and super-fine particles are generated when manufactured in the usual way. Large quantities of these fine· particles and super-fine particles have polluted the internal and external' environments of factories. The products yield' ·decreases, also. From such a background, this study examines the preparation of perfectly uniform particles that could be· collected -100% as products. Recently, NASA has succeeded in the preparation of perfectly uniform particles in zero gravity 5). But the preparation of 'perfectly uniform particles by this method is difficult, and it can not be used in general industry"

Jan 1, 2000

By A. D. Zunkel

Increasing amounts of electric arc furnace dust (EAFD) are being generated worldwide as more steel is produced from electric furnace melting of galvanized steel scrap. In most countries, the management of this material is a costly technical, economic, and legal problem for minimill steelmakers. Many technologies and processes are being developed and implemented worldwide to manage this material to recover contained zinc, lead, and iron values and render it nonhazardous. These processes are pyrometallurgical, hydrometallurgical, or hybrid in nature. Some produce zinc oxide, some zinc metal, some lead metal, and some lead cement. Some are successful, some have failed, many are dormant. or abandoned, and others continue to be developed and emerge. This paper updates the current status of 20-30 processes in various stages of commercial application and development used worldwide to manage EAFD and recover its nonferrous, particularly zinc and lead, and ferrous values.

Jan 1, 2000

By G. Ferrara, P. Bozzato, B. Chinè

To obtain a reliable comparison between conical and cylindrical separatory vessels used in dynamic dense-medium separation systems, the following two studies were made: a study of the swirling flow in conical and cylindrical vessels using laser-Doppler velocimetry (LDV) and a study of the behavior of suspensions of magnetite and ferrosilicon in water in both separators. It was found that the tangential velocity profiles differ in conical and cylindrical vessels. In a conical cyclone, free vortex conditions affect the largest part of the vessel, while in a cylindrical vessel, the motion approaches that of a forced vortex, i.e., that of a centrifuge. It was also found that the conical vessel manifests higher centrifigal acceleration and very strong densifying (the density differential) and, hence, the density gradient inside the vessel is large. It was found that the cylindrical vessel manifests lower centrifugal acceleration and low densifying, i.e., low-density differentials, and hence, the density gradient inside the vessel is small. Also, due to greater densifying, the density cut-point in cyclones is higher than the operating medium density, while, in cylindrical vessels, the density cut- point is closer to the medium density. The results provide an interesting description of the differing behaviors of conical and cylindrical vessels, and they help explain the differences in pegormance between the two types of separators.

Jan 1, 2000

By A. J. Maselli, E. C. Cemak

Hartford Steel Technologies (HST) has a pyrometallurgical and hydrometaliurgical process capable of reclaiming valuable metals from a hazardous waste· stream such as EAF Dust. The HST Process effectively addresses the growing environmental concerns surrounding the increasing production of EAF Dust without producing any hazardous waste material as byproducts. Currently EAF Dust production levels are exceeding the 1,000,000 metric tons per year mark. The HST Process is designed to separate iron, zinc, lead, cadmium, copper, and silver metals using a two-phased process. The Pyrometallurgical side of the Process utilizes a Rotary Hearth Furnace to separate the iron metal from the remaining metals. These remaining metals are further separated, using a Hydrometallurgical Process, in a series of digestion tanks. The individual metals are then collected in saleable form.

Jan 1, 2000

By A. Arik

An accurate estimation of mining block grades continues to be a challenging task for ore reserve practitioners. Two of the factors that affect the accuracy of the estimates are the estimation method used and the variability of the mineralization in the deposit. The objectives of the study are twofold: Firstly, to see how different estimation methods perform on a given deposit. Secondly, to determine the impact of particular nature of the mineralization on the results. The comparison of several estimation methods for the prediction accuracy is performed using the conditional simulation results as the basis.

Jan 1, 2000

By L. Lacerda, C. Rose, E. Zellers

Approximately six hundred air sample measurements were taken at several U.S. underground metal/nonmetal mines in 1998 and 1999. This air sampling effort was organized by the Nevada Mining Association to evaluate mining conditions and to evaluate the Mine Safety and Health Administration’s (MSHA) Proposed Rule on Diesel Particulate Matter Exposure of Underground Metal and Non-metal Miners. MSHA’s proposed air sampling method, NIOSH Method 5040, was tested under controlled conditions and under normal mining conditions. Unfortunately, NvMA sampling results have indicated that carbonaceous rock dust, oil mists and even cigarette smoking create severe sampling interference problems for NIOSH 5040.The main conclusion was that NIOSH 5040 did not distinguish between DPM and other airborne carbon particulate. Thus, it is not a reliable method of accurately and unequivocally measuring DPM in underground metal/nonmetal mines.

Jan 1, 2000