Search Documents

By D. H. Flather, J. W. Hendry, K. Drover

Black Hawk Mining Inc. has completed a comprehensive program on the prediction and management of acid rock drainage (ARD) at their Keystone Gold Mine (Keystone) near Lynn Lake, Manitoba. The program, initiated in 1994, followed a phased approach utilizing initial acid-base accounting (ABA) results and subsequent laboratory kinetic testwork to define site-specific sulphide oxidation and neutralization consumption rates in waste rock. Net acid generating waste rock at Keystone was defined through the kinetic testwork as waste rock yielding a net potential ratio (NPR) of less than two. A preliminary waste rock management program based on blending of potentially acid generating and acid neutralizing waste rock was advanced. Subsequent refinement of the management program followed the analysis of over 1580 ABA samples collected from individual blast holes during the initial bench development phase of the Keystone pit. Uncertainties in actually achieving adequate blending within the dumps at a mining- scale resulted in the development of a revised waste rock management program based on segregation. Recognizing that any successful management plan requires that the ARD characteristics of the waste rock be identified prior to in-pit blasting, the extensive ABA database was utilized to develop a rapid characterization scheme. By implementing a characterization scheme based on total sulphur concentrations and fizz rating, waste rock could be quickly segregated without delaying the natural flow of ore from the pit. Interestingly, it also became apparent that gold values were strongly correlated with total sulphur, such that traditional fire assays were supplanted with a simple and more cost-effective total sulphur determination. The program highlights the importance and benefits of collecting and exploiting data beyond that necessary to acquire appropriate development permits.

Jan 1, 2000

By J. M. Mutmansky, Y. J. Wang

The method usually used to predict the direction of flow in a connecting airway is to conduct a survey of the two existing nodes to be connected by the new pressure airway. It is then assumed that the air will flow from the node with the measured higher pressure to the node with measured lower pressure. This paper examines this direction-of-flow problem using properties of the system characteristic curve for a two-terminal network and specifies some conditions that will ensure that the air will flow in the direction anticipated. It was concluded that the only requirement is that all characteristic curves of the fans in the network should be strictly decreasing. Five numerical examples illustrate some important proper- ties of the direction-of-flow problem.

Jan 1, 2000

Just as geophysics, in the form of 3D seismic and wireline logging, plays a key role in petroleum reservoir management, so too will geophysics play an important role in mining of coal, metals, and minerals in the 21 st century. The commercial and social imperatives driving greater use of geophysics are reduced costs, increased revenues, and enhanced safety. In short, superior utilisation of capital and management of risks. In relatively undeformed sedimentary environments it is possible to adapt petroleum-style 3D reflection seismic to image mines. This has been demonstrated most impressively in the Witwatersrand. Anglo-American, for example, completed a $1 million 3D seismic survey at Western Deeps in order to site a new $300 million shaft with confidence. Likewise, 3D seismic has gained rapid acceptance at Australian coal mines in recent years. Encouraged by these successes, metalliferous mining companies are supporting research in Canada and Australia, as well as South Africa, to adapt 3D seismic for more highly structured, metamorphic terranes. Because the mining industry is far more diverse than the petroleum industry in terms of commodities and geological environments, 3D seismic is not always cost-effective. A plethora of other geophysical techniques can be applied, many of which are employed in mineral exploration. Mine applications of geophysics differ from traditional exploration applications in two main ways: time scales and length scales are shorter, and boreholes are more plentiful. Borehole geophysical techniques therefore play a more significant role, both for logging and imaging. Logging systems detail the variations of in situ physical properties down the borehole at scales measured in centimetres, while geophysical imaging techniques can map features located tens or even hundreds of metres from the sensors. While geologists tend to think of boreholes in terms of chips and core, geophysicists perceive them first and foremost as access paths for instruments. Borehole logging has been employed at iron and coal mines for decades, mainly to accurately define ore boundaries in delineation holes. In base metal mines, Outokumpu implemented logging widely for orebody delineation in percussion holes in the 1980s. The benefit was a direct cost-saving, arising from substitution of core drilling with percussion drilling plus borehole logging. The practice has since spread to other companies. INCO, for example, defines nickel boundaries in blast holes at Sudbury using conductivity logs. The benefits are in the form of reduced dilution and enhanced ore recovery, flowing from a more accurate mine model. Density, natural gamma radiation, magnetic susceptibility, and conductivity are the principal metalliferous mine logging parameters because they can be recorded in both dry and water-filled holes. Sonic velocity is the premier geotechnical logging parameter, given its sensitivity to rock strength, stress, porosity, and degree of fracturing. Sonic is recorded routinely in exploration and geotechnical holes at coal mines. With the advent of slimline dipmeter, full waveform sonic, and optical and acoustic scanner tools, the role of borehole logging in geotechnical evaluations is expanding. Monitoring of strain and micro-seismic activity enhances safety during mine production. While qualitative interpretation of logs is adequate for stratigraphic identification or definition of boundaries, a wealth of quantitative information, eg density, can be derived from properly calibrated, repeatable geophysical logs. Moreover, geophysical logs can sometimes serve as surrogates for geochemical assays, and not only for magnetite and uranium. At OutokumpuÆs Kemi chromite mine, for example, gamma-gamma logging provides the basis for grade control. By reducing reliance on assaying, three benefits can be realised: reduced reliance on core drilling; lower core handling and assaying costs; and shorter turn-around times. Conventional downhole EM and borehole magnetics are used for near-mine exploration, and for ground sterilisation. Inco has enjoyed considerable success with borehole UTEM in the Sudbury Basin, for example, and Geopeko has applied three-component borehole magnetics successfully in the Tennant Creek area. Electrical techniques such as applied potential and magnetometric resistivity (MMR) are also finding application at mines. For higher resolution, borehole seismic, radio imaging, and radar have been invoked, with varying degrees of success, to delineate orebodies and map structures, or to geotechnically characterise the rock mass and identify hazards. Success mapping nickel sulphide shoots with borehole radar has been reported by WMC at Kambalda. There are no universal geophysical panaceas, and each mine imposes different geological, logistical, and economic constraints. Geophysics will not always be cost-effective. However, the greatest single impediment to expanded use of geophysics at mines has been the low level of awareness of geophysics on the part of most mine geologists, engineers, and managers and, equally, the limited understanding of mine geology and engineering exhibited by the majority of geophysicists. This myopia will be remembered as a 20th century affliction! Blue Sky areas for mine geophysics in the next ten years include integration of geophysical data acquisition with drilling, enhanced grade estimation and rock mass characterisation, and the incorporation of geophysical information into mine models using geostatistical techniques. All these advances will be predicated on an expansion of petrophysical knowledge.

Jan 1, 2000

By N. S. Yet

This paper shall present the design and construction of bored pile and diaphragm wall for the proposed MHA complex in Singapore. The work was carried out by L&M Foundation Specialist Pte Ltd and PWD Consultants Pte Ltd was the consultant for this project. A brief description of the project is first presented to illustrate the scope and scale of the work involved, which includes the construction of bored piles and diaphragm walls and installation of steel stanchions in the bored piles. This is followed by a description of the methodology used to analyse and design the wall and bored piles. As both towers in this project are supported on bored piled foundation and are constructed by top down construction method, the analysis of the wall has taken into consideration the sequence of work phase by phase and this was carried out by means of a commercial finite element program called CRISP. Modelling of the problem will be briefly described and the findings from the numerical analysis will be presented. This is followed by a description of the structural and geotechnical design aspects of bored piles. The paper shall then describe the difficulties encountered for this project and solution used to solve the problem. The subsoil condition will be described with special mention on the encounter of very strong granitic rock at depth above the maximum excavation level of the basement at certain locations, hence necessitating the drilling of rock for a considerable depth for both bored piles and diaphragm wall. At this juncture, the construction method used to drill through the rock will be briefly described. For construction of bored piles, penetration of rock was carried out by chiselling or drilling using reverse circulation rigs. For construction of diaphragm wall, it requires the employment of Bauer hard rock cutter which uses cutting wheels fitted with roller bits and are capable of excavating into granitic rock of compressive strengths more than 100 MPa.

Jan 1, 2000

By Paul Mitchell, Clive Potter, Miles Watkins

Meldon Quarry is a seemingly rare occurrence of acid rock drainage (ARD) in a quarrying operation.4 With surface waters discharging to a tributary of a salmon-bearing river, it is subject to stringent discharge conditions. The quarry predates effective environmental management, and preventative, control and treatment measures were not implemented until relatively recently. However, retrospectively implementing standard preventative approaches at the site is costly, technically difficult and of uncertain benefit. This paper overviews the recent site history and introduces data from a demonstration by KEECO (UK) Limited of its Silica Micro Encapsulation (SME) water treatment technology.

Jan 1, 2000

By J. Tuzson, H. McL. Clark

Introduction Wear of pumps, wet cyclones and pipelines by suspended solid particles will impact their operating economies by limiting their useful life, reducing their reliability and increasing the amount of servicing. Erosion is considered a materials problem. The empirical solution consists of testing different materials in field applications. Such tests are time consuming and expensive. The prediction of localized wear rates, life estimates and appropriate material selection demand a better understanding of the slurry wear process in environments corresponding to those found in working equipment. Key words: Wear, Slurry abrasion, Coriolis erosion tester The slurry wear process Solid particles suspended in liquid generally move with the flow, but such particles deviate under the centrifugal and Coriolis forces encountered in pumps. The concentration of particles will increase, and a solid layer or bed may accumulate if the acceleration is directed against the flow passage wall. Large particles in dilute suspensions may impact the wall. dissipating their kinetic energies and removing material. However, particles smaller than about 11)(1 µm encounter great drag when moving through the liquid. and such par¬ticles have little kinetic energy left when they reach the wall. They cannot penetrate the stagnant boundary layers present in pumps. Therefore, small particles tend to form beds that slide along the wall, removing material by a process that could he called sliding erosion or wet abrasion. Wear by impact erosion from large particles in dilute slurries can he predicted by appropriate analytical and empirical methods. However, laboratory tests and calculations of wear rates that correspond to sliding erosion are more likely to correlate with field experience from wear under similar conditions. Specific energy Data from laboratory slurry erosion experiments have shown that the amount of material removed is approximately in proportion to the energy expended in the erosion process. Thus. the specific energy-energy expended in removing by erosion a unit volume of material-offers a simple, practical measure for the erosion resistance of materials. The concept was found to also apply to sliding erosion (Clark et al.. 1997). Generally, the study of the material-removal process in slurry erosion continues to remain a subject of research. Conceptually, if the flow velocities and accelerations could be calculated in a pump or pipeline, the energy dissipated at the passage walls could also be estimated, and the material removal rate would become known from the specific energy determined by laboratory tests. Slurry erosion testing Laboratory devices made specifically for slurry erosion testing may be grouped into the following: jet erosion devices, slurry pots and the Coriolis test machine (Pagalthivarthi and Helmly, 1992). Jet erosion devices use a slurry pump and nozzle to produce a high-velocity slurry jet that is directed at a flat material specimen, either perpendicularly or at some acute angle. Combined impact and sliding erosion are produced. but the processes cannot be separated, and the wear is difficult to assess except by weighing. Slurry pots consist of a cylindrical vessel containing the slurry of interest. In the slurry pot, test specimens are attached to a rotating arm. The samples are rotated in the slurry and experience local flow conditions that result in combined impact and sliding erosion. Wear depth measurements from detailed laboratory experiments have been successfully correlated with results from an analytical model of the process, and specific energy values have been calculated (Wong and Clark, 1995). In industrial use, the samples are weighed to determine the total material loss. Materials are ranked with respect to some reference material. The Coriolis erosion tester (Tuzson, 1984) consists of a rotor with a central cavity, from which two opposing radial passages lead out (Fig. 1). The slurry is fed to the centerof the rotor in one pass from a stirred overhead tank. The slurry particles are subjected to the Coriolis acceleration as they flow out through the radial passages. The material specimens are mounted into the radial passage walls facing the direction of rotation and are eroded by the particles that are pressed against them as they flow out radially. A narrow groove is worn into the sample within a few minutes, using a few gallons of slurry. Material removal is estimated accurately from profilometer traverses across the wear scar at different locations. The energy dissipated by the particles can be estimated, which leads to a well-defined experimental value for the specific energy.

Jan 1, 2000

The excavation of ramps and tunnels often requires high-speed development with (or without) the use of high-energy mining equipment such as loaders, dump trucks, TBMs and roadheaders. This high-speed development creates a challenge in terms of providing a safe and productive working environment. For example, heat from continuously exposed surrounding rock, heat from broken rock, heat generated by mining equipment, potential in flows of hot ground water, pollution from associated diesel equipment and the distance of the advancing face from fresh through-ventilation all have to be taken into account when designing ventilation systems for high-speed ramp and tunnel developments. This paper discusses methods of achieving acceptable environments at the face and along the length of the tunnel. The methodology has been successfully implemented in the development of long (up to 20 km) TBM drives in the Lesotho Highlands Project and in mining projects in hot rock using drill and blast methods as well as mechanized methods using continuous miners and roadheaders. The determination of heat loads includes calculation of the heat flow within the surrounding rock, evaluation of the operating cycle of the equipment and the contribution to the overall heat load of the broken rock as it travels out of the tunnel. The determination of heat loads from surrounding rock in new tunnels required a modification of the algorithms generally used for established excavations. The paper also examines the use of, for example, mobile duct and fan systems to ensure that fresh air is delivered to the specific areas where workers are located.

Jan 1, 2000

By J. A. Flinn

Phelps Dodge’s Morenci copper mine has had six drills, six track-dozers, 16 shovels, two loaders, and 90 haul trucks equipped with either Caterpillar, Aquila, or Modular GPS systems for nearly three years. The Caterpillar Computer-Aided Earthmoving System is an open-architecture system, which allows for inputs to enhance orientation solutions and system functionality. This system has begun a new phase that leads to an intelligent mining system. Optimization techniques of the current system and inputs are reviewed. In addition, some practical issues of implementing new technology in a mining environment have been identified to aid in this new phase.

Jan 1, 2000

Analysis of rock discontinuities, collected using a scanline method, has been undertaken at the Iron Duke open cut mine, on the southern margin of the Middleback Range in the Gawler Craton, South Australia. The iron mineralisation, which is a product of supergene enrichment of carbonate sediments, is located on the W (western) limb of a gently N plunging D2 macrosyncline. Mesofolds plunge shallowly to the NE or steeply to SE, suggesting two shortening events, of which the second produced significant macrofolds. Discontinuities include:faults and shears which display variable orientations, mainly striking WNW dipping steeply N; mesofractures or joints maintaining a well constrained orientation, dipping steeply S, subvertical striking E-W; and bedding surfaces which are folded about a gently N plunging axis. Through this example of the regional control exerted on local discontinuities, it is clear that discontinuities are not randomly distributed as often assumed in purely statistical approaches. Commonly for rocks of any age there is a distinct discontinuity pattern, reflecting the geological deformation history. If the controls exerted on local rock discontinuities can be determined and assigned a number related to their significance, the way forward is available to develop a site specifc knowledge base that can make realistic predictions for any position in a given rock mass. Such a procedure would involve assessment of the regional geology, linked to scanned discontinuities either via manual or automatic means. Recent advances in automatic scanning rock faces (eg by the I-SiTE Laser Radar) to determine discontinuities distributions, enable the rapid calculation of rock characteristics. This is a significant advance in rock engineering, providing a method of safe and quick collection of data. However it creates problems in the presence of an increase in the geotechnical data available, which should be assessed in the context of the regional geology. Although techniques are underway to analyse post-blast discontinuities, the next signifant potential advance in this area could be the integration of a knowledge based system to assess discontinuities ahead of mining, incorporating regional assessment and human intuition.

Jan 1, 2000

By Greg Mclellan, Mark Johnson, John Pepper

Several large quarrying projects recently occurred in Miramar, Florida. These were closely monitored by the Seismologist of Record and Broward County in accordance with County and City regulations. In addition to this monitoring, the City of Miramar employed The Pepper Engineering Group, Inc., to provide additional spot check monitoring and to review the records of the other two parties on a routine basis. Broward County ordinances require that the location of each shot and the nearest protected structure be recorded along with seismograph measurement of each shot at the nearest protected structure. The positions of the blasts and nearest protected structures were determined using GPS. The blast vibrations were measured by seismograph. Over 600 shots, which are the subject of this study, were measured both by the County, the Seismologist and, on many occasions, The Pepper Engineering Group. As such, the vibration data was constantly cross-checked for consistency. The blasting contractor also provided blast designs for each shot. In this paper, the measured vibrations are plotted in terms of Resultant Peak Particle Velocity (RPPV) versus Scaled Distance (SD) on logarithmic scales. The data curves are fitted with least squares and upper 95% and 99% prediction limits are provided. Equations are presented to predict the RPPV based on scaled distance and prediction level using power fits. Statistical information concerning the derivation of the various limits is presented. The raw data used to develop this paper, along with other information concerning the shots, will be posted on the Internet for use by other researchers.

Jan 1, 2000

By Rajive Ganguli

There are several elements of online pedagogy and information technology that are being used in the University of Alaska Fairbanks’(UAF) course “ES 201: Computer Techniques,” to enhance classroom teaching. The use of information technology in this class grew from a desire to make lecture notes available to students. This has grown to include a sophisticated, online delivery software package. It provides chat rooms, discussion groups, and online testing and grading. Online delivery aside, the class uses the telnet, e-mail and C++/FOR-TRAN compiler facilities of the university server during class to enhance learning. During class, for example, the students read the lecture notes on the Web browser, telnet to their university Unix accounts, check their e-mail and download programs (to be covered in class) sent by me, and then compile, run and modify the programs. The class, therefore, requires students to be active most of the time. This ensures their full attention and better learning due to the hands-on experience (Fig. 1).

Jan 1, 2000

By S. Banisi, M Nesari, J. A. Finch, N. Nobari, H. Javani

"The flotation circuit of the Sarcheshmeh copper mine, which processes 40,000 t/d of ore at 0.9% Cu, consists of rougher, cleaning and recleaning stages. Mechanical flotation cells are used in all stages. To investigate the amenability of flotation columns in the plant especially for cleaning and recleaning stages, a column was designed, constructed, and installed at the Sarcheshmeh pilot plant. The pilot plant, which has an identical circuit configuration compared to the plant, can process up to 2 t/h of ore. The overall rate constant of the ore along with the target recovery of 94% were used to size the column. A 26 cm by 550 cm column with two filter cloth spargers and a submerged froth washing system using perforated tubes was constructed. To detect the interface level a 180 cm conductivity probe consisting of 1.5 cm diameter ring electrodes was installed. The tailings flowrate controlled by a variable speed pump was used as the main control variable. The initial testing program revealed that the optimum superficial gas and wash water flowrate were 1.5 and 0.3 cds, respectively. It was observed that the cleaning stage grade when using the column could increase by 2-3% at constant overall copper recovery.IntroductionThe Sarcheshmeh copper ore body which may rank as third or fourth largest in the world contains 1 billion tomes averaging 0.90 % copper and 0.03 % molybdenum. It is in located south-east Iran and has been processing 40,000 t/d of ore since 1982. After three stages of crushing, the ore with a F80 of 12.7 mm is fed to 8 parallel ball mills in closed circuit with cyclones to produce a product 70% finer than 75 microns. The concentrate of the first stage of flotation is reground and the tailings constitutes the main component of the plant final tailings. A concentrate with an average grade of 31% Cu (chalcopyrite and chalcocite) is obtained after cleaning and re-cleaning stages in mechanical cells. Total recovery of the plant varies between 83-87 % depending on ore type and operating conditions."

Jan 1, 2000

By L. C. Stilwell

Input-output analysis is a major branch of quantitative economics, and is used to analyse the flow of goods and services between production sectors in a national economy. Its purpose is to determine the relative value-adding capacity of each sector. The model has also, in recent years, found increasing use in assessing the environmental and ecological impact of development projects. It has, however, never been applied to individual production facilities, such as large mines, which themselves have complex economic structures, through which there is a flow of goods and services. Conventional cost and accounting systems, as used on mines, treat production sectors as separate cost centres, and do not determine the inter-relationships between them. This can lead to incorrect conclusions on the relative value of sectors and their impact on the total economic performance of the facility. This paper explains the basic principles of input-output analysis, and presents an example of its application to a simplistic model of a mine, which is used in the absence of any real data. The paper concludes that, by forcing definition of the value adding function of each sector, input output analysis will facilitate control of inputs, or costs. This will result in optimal application of resources and exploitation of ore reserves. The authors realise the model needs to be tested on an operating mine, and hope this paper will result in an opportunity to do so. The authors wish to thank the anonymous referees for their valuable comments.

Jan 1, 2000

By Bingchen Chen, Zhitong Sui, Junwei Ma

"In the blast furnace slag, titanium disseminated in various mineral phases Titanium could be concentrated mainly in perovskite, which could be selectively precipitated and grown by optimizing the operation factors like the slag composition, temperature of heat treatment and additive agents. This study aims at establishing the titanium slag mineralogy and its distribution in the treated slag and the as-received slag, as well as the methods of perovskite separation. After heat treatment, the grain size was grown from 5 - 20µm to 80 - 200µm, the distribution of Ti02 in perovskite was increased from 48% to 81 %, the morphology was changed from snow-shaped grain to coarsening dendrites or equiaxed crystals. A concentrate were produced by gravity separation analyzing 35.25% Ti02 with a recovery of 68.28% and a tailing analyzing 9.53% Ti02 , and a possibility of flotation upgrading was discussed. I INTRODUCTION CHINA is rich in mineral resources of titanium, 92.4% of which is vanadium-titanium bearing magnetite. About 53% titanium were in iron concentrate after mineral processing, by which the blast furnace slag containing about 25% TiO2 were produced[11 • The content of TiO2 in such slag is too low to separate titanium dioxide, and it is also too high to produce slag cement[21. It has been accumulated to 50 million tons so far, which is still increasing at a rate of 3 million tons per year, and results in a waste of titanium resources and pollution of environment. Due to the dispersed distribution of titanium component in various mineral phases, very fine grain(<10µm) and complex interfacial combination, it is very difficult to recovery titanium component from the slag by traditional separating technique. In this paper, a novel technique to recovery titanium from the waste slags was proposed [3H4l, on which three continuous processes were involved: selective concentrating, selective growing and selective separating. Perovskite was designed as a titanium-rich phase, in which the most titanium was concentrated promptly, then perovskite could be selectively grown and coarsened by optimizing the heat treatment and the appropriate additives [ 5l[6l. The grain size of perovskite phase was larger than 80 µm, and the crystals appeared as coarsening dendrites or equiaxial grains like lump."

Jan 1, 2000

By D. H. Rubisov, V. G. Papangelakis

Sulphuric acid pressure leaching is the process of choice to recover nickel and cobalt from laterites with variable iron and magnesium contents. The latter influences the acidity levels required for effective leaching of nickel and cobalt, and during leaching, iron is rejected in-situ as hematite. Classical solid/liquid separation is performed via a CCD circuit, the performance of which depends upon the size and shape of precipitated particles. In this paper, precipitates obtained by acid-leaching of various lateritic feeds at 270°C are characterized using SEM/EDX and laser particle size analysis. It is shown that as acidity increases, the shape of the precipitates gradually changes from platelets to spheres, thus improving the S/L separation properties of the residue. The use of hydrogen ion concentration “at temperature,” calculated from a speciation analysis, allows the explanation of this change of morphology independently of the type of the ore feed. The possibility of precipitating magnesium sulphate “at temperature” is also discussed. In order to take advantage of this precipitation for scale reduction (as has been proposed in the past) without compromising the residue quality, [H+] “at temperature” must be controlled within an optimum range.

Jan 1, 2000

By P. -M. Tardif, S. Outalha, R. Le

"This paper proposes a new direction to implement an underground mine communication system. It presents actual underground communication systems and discusses their technological limits. A new system based on a wireless local area network (WLAN), together with its main systems characteristics, is then proposed. This paper also presents an experimental protocol for radio frequency propagation measurements. Finally, the paper describes the projected implementation of a WLAN in an experimental mine. IntroductionDuring the last decade, a number of Canadian mining companies have invested in modern communications systems in order to automate processes and reduce operational costs. Safety of miners is also a concern, regulated by health and safety regimes.Underground communication systems rely mainly on analog technology (especially the leaky feeder). Digital upgrades have been made to modernize this technology using a coaxial or fibre optic cable to transmit voice, documents, commands, controls, and video. Therefore, all wired equipment can benefit from an increase in efficiency from the digital technology.However, when it comes to mobile equipment, the only medium was, and is, still radio waves. With the advent of the wireless local area network (WLAN) standard, one can use a technology similar to that of the cellular phone to connect transparently different equipment. WLAN enables the transmission at rates higher than 2 M bits of voice, documents, commands, controls, identification, and of course, digital video. This technology was developed with inbuilding use in mind. Now, one can try to adapt it to underground mines."

Jan 1, 2000

By M P. Simpson, J L. Mauk

The Golden Cross, low-sulfidation, epithermal deposit shows a number of features that are directly or indirectly related to boiling hydrothermal fluids. Occurrences of lattice calcite and their quartz pseudomorph equivalents in veins, and occurrences of adularia in veins and in the surrounding altered rocks in the vicinity of ore, are both direct evidence of deposition in the presence of boiling hydrothermal fluids. Loss of carbon dioxide causes calcite deposition (platy variety) near the level of first boiling, while adularia deposits due to the attendant pH increase along the cooling flow path. Indirect evidence of boiling include crustiform-colloform quartz banding, late massive calcite veins, clay-carbonate alteration in the shallow and peripheral parts of the ore zone, and the restricted vertical interval of precious metal mineralisation. The colloform quartz banding strongly resembles the banding in amorphous silica deposits found in geothermal surface pipes. This implies that fluids ascending the Empire Vein structure were saturated in amorphous silica. If so, then they must have undergone phase separation, which initiated at considerable depth (e.g. =1000 m) and very hot temperatures (e.g. =300¦C). On the basis of stable isotope data, late massive calcite veins appear to have deposited from CO2-rich steam-heated waters. Calcite deposited along heating paths as these waters descended into the upflow zone during late stage collapse of the hydrothermal plume. In active systems, such steam heated waters form by deep boiling. The high CO2 contents of these waters promote hydrolytic alteration and the formation of clay-carbonate alteration. Reaction path modelling using CHILLER and a deep, Broadlands-Ohaaki water as an analogue, shows that minerals deposit along boiling flow paths over discrete spatial intervals. Calcite and adularia deposit near the site of first boiling, followed by gold and then by amorphous silica. For deep boiling starting at 300¦C, these minerals deposit over a path length that exceeds 1000 m. The distribution of banded quartz and gold at Golden Cross are consistent with such a boiling model. However, the elevation of first boiling must have fluctuated over 500 m to account for the coincidence of lattice quartz (pseudomorphs of platy calcite) and adularia, crustiform-colloform silica and gold over distances of a few centimeters in veins. We deduce that a downward propagating boiling front and expansion of two-phase flashing in a flowing water column occurred during episodes of high vertical permeability and fluid flux in the Empire vein structure.

Jan 1, 2000

Traditional fine grinding mills in mineral processing relied on the use of steel medium for particle size reduction. The successful development of the Isa Mill(a horizontal stirred mill with 3000 litres of net chamber volume and 1120 kW rated motor power)adopted a novel product separator design that has led to a major revision of medium use in fine grinding. The Isa Mill separator has also successfully operated with a wide variety of medium types such as silica sands, river gravel, smelter slag, run-of-mine ore fractions and steel shots, with size ranges from 0.5 to 10 mm. A great flexibility of the Isa Mill operations has been achieved for processing a feed as coarse as 120 um to a product as fine as 5 µm. This paper discusses the performance of two inert grinding media used in the Isa Mills in Mount Isa Mines of Australia for processing galena and sphalerite bearing ores to below 10 microns. They are the copper reverberatory furnace slag (CRFS)and the heavy medium plant rejects (HMPR). A methodology was also demonstrated for comparing the medium performance and for scaling up the Isa Mills from a 1.5-litre laboratory batch mill to a full scale 3000-litre mill.

Jan 1, 2000

By Joseph A. Dos Santos

The Expanded Conveyor Technology, a rationalization of the conventional conveyor technology, allows us to apply the theory and principles beyond the current (perceived) limits. This was first prompted by the writer&apos;s advancements in Sandwich Belt High Angle Conveyors. The introduction defines the Expanded Conveyor Technology and outlines the range of applicability for the wide variations in conventional and non-conventional conveyors. The writing deals with the theory and design of sandwich-belt, high-angle conveyors in the context of the Expanded Conveyor Technology, including the equations of friction, hugging pressure and the continuity of hugging principle; curvature constraints and criteria for tension, curvature, trough, and belt construction; and drive and tension analysis, load sharing and traction, including "derived load equivalents."

Jan 1, 2000

By P SSrkkS

Mining is commonly seen as a typical basic industry with rough and even dangerous working conditions, heavy environmental load, and a low level of high-technology and automation with much manual work and operations. A mining operation (open pit or underground) is a very complex one consisting of many manual, physical, mechanical and logistical operations with different human interfaces and decisions. For this reason it is a demanding and potential area for all applications of automation and information technology: controlling difficult non-linear, time varying multivariable processes and machines; solving of ergonomic safety and environmental problems; automation of logistical systems; applying robotics, mechatronics, and information handling, etc. In addition to that, big economic sums are involved with these operations. On the other hand, automation technology has developed towards intelligent and adaptive systems including some from the above mentioned fields of automation. Connecting them with modern information and communication technologies makes the idea of an intelligent and unmanned mine more and more feasible in the near future. This requires intensive co-operation and co-ordination between the mining industry and manufacturers of mining machinery. This has been successfully accomplished in the five-year Intelligent Mine research and development program as well as the three years of subsequent implementation of its results in Finland. The basic elements of an Intelligent MineTM concept are:mine-wide information and data acquisition system; high-speed two-directional mine-wide communication network for real-time monitoring and control; computerised information management, mine planning, control and maintenance systems; automated and tele-operated machinery and equipment which are connected to the information system; and links to the public information networks. The degree of automation of an intelligent mine depends on many technical and economical factors. The basic precondition for such an approach is that it will improve the total economy of the mine. This paper will describe the Intelligent Mine Technology Program with the results. Also the implementation which took place during starting of a new underground mine (Outokumpu Chrome Oy Kemi Mine) will be described.

Jan 1, 2000