Search Documents

By Patrick Clark

As part of the Mine Waste Technology Program (MWTP), a large-scale column test using bacteria and a sulfide ore was conducted at McClelland Laboratories, Inc., in Sparks, Nevada. Four technology providers participated in this demonstration. A mining company in Nevada provided the sulfide ore, process effluent and make-up water. A process effluent column, a chemical oxidation column, and the four biological treatment columns were set side by side on a test pad outside the laboratory building. The process effluent and chemical oxidation columns were used for experimental control. The goal of this project was to evaluate the viability and feasibility of using these biodegradation technologies to reduce the cyanide to the regulatory level of 0.2 parts per million (ppm) within an acceptable timeframe and with low operational costs. The column testing began on December 3, 1998 and operated until May 17, 1999. One technology provider reached the regulatory level within the 158 days. The remaining three biotechnology columns were approaching the regulatory limit at completion of the demonstration. The MWTP is funded by the U.S. Environmental Protection Agency (EPA) and is jointly administered through an interagency agreement with the U.S. Department of Energy (DOE).

Jan 1, 1998

Many studies have been conducted over the past 3 decades on the leaching of gold in solutions containing thiosulfate, ammonia and copper. However, most of these studies have been carried out using ore samples, with very few fundamental studies of this system being attempted. The majority of the published studies have failed to acknowledge the undesirable side reaction between copper(H) and thiosulfate, let alone account for its effect. The fact that the solution chemistry is constantly changing makes it very difficult to perform a fundamental study of gold leaching. With the advent of the rotating electrochemical quartz crystal microbalance (REQCM), such fundamental studies are possible as this instrument measures mass in real time. This has allowed leach kinetics to be measured in a matter of minutes and hence at essentially constant solution conditions; The present paper highlights that a sufficient concentration of copper(II) and ammonia are required in order to achieve appreciable gold leach rates. However, the use of air (oxygen) to maintain the copper(Il) concentration catalyses the undesirable copper(II) reaction with thiosulfate. The presence of ammonium ions is shown to have an effect on this undesirable reaction as well as on the gold leaching ?reaction. Preliminary electrochemical studies into .gold electrowinning using the REQCM show that gold(I) thiosulfate cannot be readily reduced to metallic gold in the potential region at which cementation usually occurs. However, it is well known that gold cementation onto copper occurs rapidly. The current study addresses this discrepancy by studying the effect that copper and silver have on the reduction of gold thiosulfate. It has been found that the presence of both silver and copper enhance gold deposition, particularly at low over potentials. While this is beneficial in cementation, the presence of copper and silver in solution has been found to cause passivation of the cathode surface during electrowinning at 'higher overpotentials.

Jan 1, 1998

A very wide range of technologies are utilised in the mining and processing of ores and a great deal of effort is expended in the development of ænew technologiesÆ to improve mining performance and economics. Traditionally, technology and people have been treated as separate aspects of an operation, when in fact they are inextricably linked. The successful implementation of new technologies is entirely dependent upon the actions, enthusiasm and skills of people, both as individuals and working in groups. This paper discusses the role of technology in mining and how new technologies are implemented by the industry. The paper argues that existing technologies have not been fully or adequately utilised and that effort should be re-focussed on the implementation of technologies that have been taken for granted for many years. The need for greater emphasis to be placed on the management of the human-technology interface is discussed.

Jan 1, 1998

By R. V. Ramani

"In this paper, the current status of respirable dust control in coal mine atmospheres is presented. The advancements in the engineering control of dust generation and entrainment, and of reducing the exposures are summarized. The results of the Health Surveillance Program are briefly reviewed. The results of research conducted in the Generic Mineral Technology Center for Respirable Dust are presented. The 1995 NIOSH criteria document on respirable coal mine dust is briefly reviewed. The fundamental scientific and engineering issues in need of research are discussed. A detailed bibliography is attached.IntroductionFor coal mines in the United States, the current permissible exposure limit (PEL) of 2mg/m3MRE-equivalent concentration (an 8-hour TWA concentration measured gravimetrically) was established by Public Law 91-173: the Federal Coal Mine Health and Safety of 1969 (the 1969 Coal Act). This standard is reduced when the respirable quartz content in the dust sample exceeds 5%; the reduced standard in mglm3 is obtained by dividing 10 by the percent quartz. The OSHA and ACGIB PEL for respirable coal mine dust is also 2 mg/m3 , and OSHA PEL for respirable quartz is 100 µg/m3 . The 1969 Coal Act also prescribed two activities in the Coal Mine Respirable Dust Sampling Program and the National Coal Workers' Health Surveillance Program n to control respirable dust in mines, and the coal worker's pneumoconiosis (CWP) among the coal miners.There are three principal methods by which personal exposures to respirable dust are controlled. The first is engineering control where the aim is to reduce the concentration in the mine atmosphere to or below the mandated level. The second is the provision of personal protective devices which allow the miner to work in dusty atmospheres without increasing personal exposure. The third is the use of administrative controls where the miner's exposure is controlled through work schedules and procedures to keep miner exposure at or under the mandated levels. The 1969 Coal Act specifically prohibits the use of respirators in lieu of environmental control. The compliance sampling program essentially does not give any credit to the use of administrative controls."

Jan 1, 1998

Kroemer(1-3) and Kroemer et al.(4) define the isoinertial technique of strength assessment as one in which mass properties of an object are held constant, as in lifting a given weight over a predetermined distance. Several strength assessment procedures possess this characteristic. Most commonly associated with the term is a specific test developed to provide a relatively quick assessment of a subject's maximal lifting capacity using a modified weight-lifting device.(1,5) The classic psychophysical methodology of assessing maximum acceptable weights of lift is also considered an isoinertial technique under this definition.(6) While the definition provided by Kroemer(1) and Kroemer et al.(4) has been most widely accepted in the literature, some have applied the term "isoinertial" to techniques that differ somewhat from the preceding definition, such as in a description of the Isotechnologies B-200 strength testing device.(7) Rather than lifting a constant mass the B-200 applies a constant force against which the subject performs an exertion. The isoinertial tests described here apply to situations in which the mass to be moved by a musculoskeletal effort is set to a constant. Is Isoinertial Testing Psychophysical or Is Psychophysical Testing Isoinertial? As various types of strength tests have evolved over the past few decades, some unfortunate developments in terminology have arisen to describe and classify different strength assessment procedures. This is particularly evident in sorting out various tests that have been labeled "isoinertial." One example was cited earlier. Another problem that has evolved is that the term "isoinertial strength" has two connotations. The first is the conceptual definition: isoinertial strength tests include any strength test in which a constant mass is handled. In practice, however, the term is often used to denote a specific strength test in which subjects' maximal lifting capacity is determined using a machine and a constant mass is lifted.(1,5) Partially as a result of this dual connotation, the literature contains references to both "isoinertial strength test" as a psychophysical variant(8) and the psychophysical method as an "isoinertial strength test" (4,9) To lay the framework for the next two chapters, the authors will briefly discuss some operational definitions of tests of isoinertial and psychophysical strength. In stating that the isoinertial strength test is a variant of the psychophysical method, Ayoub and Mital(8) refer to the specific strength test developed by Kroemer(1) and McDaniel et al.(5) Clearly, this isoinertial protocol has many similarities to the psychophysical method: both are dynamic; weight is adjusted in both; and both measure the load a subject is willing to endure under specified circumstances. However, while both deal with lifting and adjusting loads, there are significant differences between the psychophysical (isoinertial) technique and the Kroemer-McDaniel (isoinertial) protocol in their procedures and the use of the data collected in these tests. For our purposes, we designate the

Jan 1, 1998

By P G. Hicks

The influence of feed size and pulp density on the specific rate ofbreakage of quartz was investigated. Plots of log fraction of feedremaining within the feed size interval against grinding time allowed the application of the first order grinding model to be examined. Substantial non-linearities were observed for all feed sizes due to environmental and material factors. For feed sizes above 1.3 mm, the specific rate of quartz breakage was higher with rod milling than ball milling, but below this size the reverse was true. Material that remained in the feed size interval after the initial grinding broke more slowly in subsequent grinding than the original feed material. Grinding media and time as well as feed size influenced the effects of pulp density on grinding. More dilute pulps (eg 50 per cent solids density by weight) were favoured for higher rates of breakage in rod milling but for ball milling, the optimum pulp density appeared to be 60 to 70 per cent solids by weight.

Jan 1, 1998

By M. Cai

Transformation of the measured borehole deformations induced by stress relief relies on the traditional assumption that the rock is continuous and homogeneous. Systematic and quantitative tests were carried out to check the performance of devices commonly used for measuring borehole deformations within different types of discontinuous rock conditions. Test results provide a reliable basis for considering the influence of discontinuities on in situ stress measurement and for choosing the best measuring device for a given rock type and condition.

Jan 1, 1998

The total cost of horizontal development can be minimised by optimising the cost of each of the component operations (eg drilling, blasting, etc). Component costs should not be minimised. To optimise blasting results (ie the mean advance per round, muckpile characteristics and overbreak), operators need to optimise the blast design and drilling and blasting procedures. The costs of pulling extremely long (say >6 m) rounds, producing unnecessarily fine fragmentation, and minimising overbreak are excessively high. Operators should continually consider how they can shorten the cycle period by saving time at the face. To enable it to be matched to the pertinent rock properties, the blast design needs to be based on as much relevant experience as possible. To develop the most valid correlation between blasting results and blast design, the latter must be implemented carefully and accurately, but without sacrificing speed excessively. The total cost can often be reduced by using: 1. computer-controlled jumbos (to reduce the period and cost of drilling and to increase drilling accuracy); 2. larger diameter (51 mm to 64 mm) and longer (4.5 m to 6 m) blastholes; 3. at least three large diameter ( ¦89 mm) relief holes that are 0.2 m to 0.3 m longer than the blastholes; 4. explosive products that are selected on the basis of proven reliability and overall cost efficiency rather than price; and5. stemming (to increase the amount of effective work done by each kilogram of explosive and, hence, to reduce the powder factor and possibly the number of blastholes and the costs of drilling and initiation). Non-perimeter blastholes should be charged with ANFO or a bulk emulsion of established performance. Upper perimeter blastholes should be charged with a bulk explosive with a much lower effective density. But where geology varies considerably, greatest control over overbreak could possibly be achieved with the versatile pre-assembled charge shown in Figure 1. This paper presents numerous potential ways in which the total cost of development can be minimised. It concentrates on recommending blast design features and the safe, rapid, cost-effective implementation of designs.

Jan 1, 1998

By P. V. Golde, R. A. Poole, G. R. Baiden

"INCO is committed to proceed into the next century using automation and robotics to achieve safety and productivity goals necessary to enhance its competitive position. Stobie Mine, decades old, is the first of its mines to change from labour-intensive to automationassisted techniques. This paper is a synopsis of the progress made during the transition period including overviews of some of the projects as well as some of the difficulties in the assimilation of the technology. BackgroundThe ObjectiveThis paper is an update on remote control and LHD automation installation at Stobie mine. The communications system installed at the mine and the ability to remotely control underground equipment from surface is reviewed (Poole et al., 1996, 1997). It discusses some of the experiences and processes required to further the concept to consolidate the operation of multiple machines under a single operator. It considers the communications systems requirements and their focuses, particularly on the development of systems for the tele-operation of LHDs and drilling machines from surface."

Jan 1, 1998

By Susumu Okabe

Mitsubishi Continuous Copper Converter employs the top blowing lance system for the continuous supply of reaction gases into the molten bath. In order to avoid the excessive refractory wear caused by the melt splash without loss of the reaction efficiency, the furnace design and the blowing condition should be optimized. Empirical equations which correlate the splashing rate on the' side wall with the dimensions of the furnace, lance position, lance size, gas velocity and bath properties were obtained by by the physical model study, and compiled into a computer program. The computer program is effectively utilized for the analysis of the actual operation and for the optimum design of new furnaces.

Jan 1, 1998

By Tianrui Xu, Chaohong Liu, Bangqing Ding

The authors were responsible for a series of large scale multiple chamber charge blasts conducted in the granite mountain area for making construction space on the southeast sea coast in China during 1993-1996. This paper describes the blast design and damage control of one mountain blast 320m in length and 280m in width in the vicinity of two wharfs and a dam. In order to obtain better rock fragmentation and muckpile, the explosive charge should be well-distributed in the mountain. The charge pattern, therefore, was designed with mainly 5 rows of tunnel charge in regular terrain in combination with a chamber charge in irregular topography area and the maximum burden was limited to be less than 38m. In order to protect the dam and wharfs the firing sequence was carefully arranged in 29 intervals and the distance between different charges of the same delay to the dam or wharf was taken into account as an additional delay interval based on the difference of p-wave propagating times. The maximum charge fired in an interval was also limited to less than 34t explosives through dividing the larger charge by a stemming deck.

Jan 1, 1998

By T. A. Toney

With new lightweight designs, spirals have become standard equipment in coal preparation plants worldwide. To their credit, spirals typically show very low coal losses to the refuse stream under most operating conditions. However, spirals do tend to separate at cut points in excess of 1.80 S.G. Attempts to obtain lower cut points have typically resulted in coal losses to middlings. Middlings retreatment with secondary spirals is therefore becoming common place. Other forms of retreatment with water-only cyclones, hydrosizers, and recirculation have been attempted with some success. This paper reports on a novel (Patent Applied For) approach to retreating spiral middlings m a heavy-media-cyclone circuit.

Jan 1, 1998

By K. R. Miller

In recent years, surface mine equipment operators in the Campbell County region of the Wyoming Powder River Basin have found new ways to solve old problems. This paper will examine overburden stripping equipment and techniques by focusing on evolving applications for draglines, shovels, and dozers.

Jan 1, 1998

By M McGeough

Following the success of calcrete sampling at Challenger, calcrete sampling has been widely adopted as the primary exploration technique for gold exploration, in the Gawler Craton. Calcrete is uniformly distributed over large areas and produces discrete gold anomalies. This allows drilling to focus on specific gold anomalous targets. However, despite widespread use of calcrete sampling, very little is known of the origin of calcrete in the Gawler Craton, and the link between calcrete gold anomalies and primary mineralisation. In an attempt to understand this association Lisa Gibbons recently completed an honours project at the Old Well Prospect approximately 45 km SSE of Tarcoola. Her work is part of a collaboration between CRCLEME, MESA and MIM Exploration. At Old Well, a calcrete anomaly (>10 ppb Au)covers an area approximately 7 km x 2 km with a peak value of 97 ppb Au. The study looked at the regolith as a whole, processes of its formation and nature of mineralisation within it. She was able to combine previous calcrete and drilling results with her own observations. The results from this study highlighted problems in relating surface calcrete anomalies to in situ gold mineralisation.

Jan 1, 1998

By P Hatherly, H Gurgenci

With the depletion of the mineral reserves that can be mined by surface mining, demand for highly productive and safe underground mines will increase. Underground drill and blast techniques continue to be refined but true æmass productionÆ is difficult to achieve. As is evidenced by the longwall mining of coal, alternative mining methods based on mechanised mining can meet the expectations but the issues of how to effectively cut strong rocks, how to define the orebody and how the mechanised miners can be automated and maintained all need to be addressed. CMTE is working in all of these areas. We believe that the oscillating disc cutter may provide the long sought-after breakthrough in mechanised rock cutting. Disc cutters are one of the most robust designs of cutting tool and the cutters attack the rock in a manner which effects direct tensile breakage. The internal cutter drive and the inertial damping mean that the already low cutter forces are not all transmitted back to the machine, making it possible to design lightweight, flexible mining systems. For orebody delineation drill monitoring, drillhole logging and geophysical imaging are key procedures being developed at CMTE. To automate mining machines, work is progressing well in the development of systems for autonomous vehicle navigation and mining robotics. A strategic contribution to maintenance issues is being made through the development of procedures for automatic analysis of used oils, monitoring the strength of mechanical structures, and operating point optimisation.

Jan 1, 1998

By F. C. Nicolli, J. P. Barbosa, P. S. M. Soares, A. V. Estevez

INTRODUCTION Spent household dry cell batteries are frequently disposed of with metropolitan wastestream (MSW) in landfills where they can leak due to handling or aging. Frequent rain and sun cycles, especially in tropical environments, coupled to the action of leachate, dissolve their metal constituents which will eventually reach rivers, lakes and underground water. It is well known that some of these metals are fundamental to sustain life and that is why living organisms concentrate them through their metabolism, but it has been also recognized that beyond specific limits they can definitely be deleterious to the environment. In other words, high concentration of heavy metals are proven to cause chronic or acute diseases and toxic reactions, by acting on mammals' kidneys, liver and nervous system. In addition, some metals frequently used in household batteries, as mercury and cadmium, are said to be carcinogenic (Landis et al. 1995, Silva et al. 1988). Occasionally, plants to treat MSW are coupled to compost production. Household batteries present in MSW can be dragged into these plants, contaminating their products and eventually reaching vegetables making them not proper to consume by people and animals. Alternatively, batteries are also conveyed to incinerators and burned, throwing into the atmosphere volatile species. These can either act as contaminants as toxic vapor species or be delivered by winds and scavenged by rains contaminating soils and water far away from their source. In conclusion, despite the treatment applied to MSW, one can say that battery residues are potentially environmentally hazardous. The careful assessment of the environmental impact caused by residues of household batteries it is not an easy task and it can be referred as a multivariable problem. First, many different household batteries are produced by industry and the potential environmental hazard associated to their disposal depends primarily on the type of battery and manufacturer's technology. These characteristics will dictate how resistant the battery case is to handling and the

Jan 1, 1998

By T. Carageorgos

The removal of arsenic from process streams as ferric arsenate compounds is being practised by mining industries. Therefore, the solubility and stability of these solids is of considerable importance to the mining plants that have to keep the environment free from pollutants. There is some information on the solubility of the ferric arsenate compounds, mainly on scorodite, obtained from synthetic solution. However, there is not so much work on ferric arsenate compounds formed at high temperatures (175 - 230°C) during the leaching process. In the present work, the solubility of the ferric arsenate compounds formed during acidic pressure oxidation of arsenopyrite is presented. The results of the solubility tests showed that the ferric arsenate compounds formed at high temperatures (200 - 230°C) and high pressures (1034 - 1551 kPa 0,) released arsenic into solution in amounts less than 1.2 ppm and iron in amounts no higher than 1.0 ppm. So, they seem to be potential compounds for arsenic and iron disposal.

Jan 1, 1998

By J D. St George

In this paper a laboratory investigation into the effect of confining stress, water content and gas desorption on coal permeability is presented. Of major significance is the effect of coal permeability on outburst occurrence and methane production, which is influenced by changes in stress. Test results indicated that the shrinkage of the coal matrix associated with desorption is greater than the coal matrix compressibility which will cause a reduction in the effective stress, hence increasing coal permeability.

Jan 1, 1998

By R. R. Tatiya

"The ultimate aim of a mine design is to determine the development work involved and resources required by adopting one or more specific alternatives. A part of the process is the production of mining plans/designs, an outline of the amount of work and costs involved as well as a prediction of the revenues expected. The paper aims to examine these aspects of mine design using the computer models developed. These models are capable of designing and performing economic analysis for one or more stopes for a continuous orebody. IntroductionTatiya and Allen (1987) have described ’defining stope boundaries using a computer.’ Using the stope boundaries defined or even hypothetical ones, algorithms have been prepared to design the layouts of the following stoping methods: 1. sublevel stoping (longitudinal as well as transverse);2. DTH (Down-the-hole) stoping; and3. flat back cut and fill stoping with posts and pillars.Tatiya (1989) presented this work at the 21st symposium on the application of computers and operations research in the mineral industry (APCOM). Economic analysis of a stope is the additional feature incorporated with these algorithms.The system has been tested by an economic analysis of the three stoping methods modeled for a small portion of a deposit of a copper mining complex. The deposits at this mining complex form lenses of varying shapes and sizes, having low copper content. These chalcopyrite lenses are steeply inclined with a thickness in the range of 5 m to 60 m. The strata are competent and suitable for underground mining.In different sections of the mines different sets of equipment are used to perform the basic unit operations. Some of the ore handling levels in the mines are trackless, the rest are tracked."

Jan 1, 1998

By Dave Southworth

After Abe Lee discovered gold (in April 1860) near the site of present-day Leadville, Colorado, he and is group staked nearly all of California Gulch with "speculative claims." They did so in an effort to grab any property that might be potentially profitable. But the plan did not work. New prospectors demanded a miners' meeting, from which arose the official "Bylaws of California Mining District, California Gulch, Arkansas River." These bylaws, adopted on May 12, 1860, established provisions as to the number, size and type of claims that could be filed. Fair laws invited more newcomers. By mid-summer, 5,000 people with tents and wagons were scattered from one end of the gulch to the other.Among the earliest arrivals to the region that spring were Horace Austin Warner Tabor and his wife, Augusta. H.A.W. Tabor, who was to become a pillar in the development of Leadville, arrived at California Gulch during a food shortage. He sacrificed his oxen so that hungry miners could eat. By doing so, he immediately became the friend of many. Augusta established a little store where she sold her baked goods and provided meals. Like most of the men, Horace prospected the surrounding hills. He only did so, however, for a short time. California Gulch yielded more than $5 million in gold during the next five years. By 1866, however, the placer gold was gone and most of the miners had packed up and left. Charles J. Mullen and Cooper Smith, who were grubstaked by a Philadelphian named J. Marshall Paul, found a new, rich lode at the Printer Boy Mine in 1868. It was the first underground gold mine in the Leadville area and marked the transition from surface mining to underground hard rock mining. Its discovery created a new but modest flurry of activity. Heavy black sand covered the region and made gold mining difficult. In 1875 William Stevens and Alvinus Wood decided to have the sand assayed. They discovered that it contained 15 ounces per ton of silver and was rich in carbonate. Stevens and Wood kept their find a secret for nearly two years. When the word spread in late 1877, the silver boom was on. In 1878 prospectors, merchants and others trickled into town from all directions. Dr. David H. Dougan closed his office. in Alma, crossed Mosquito Pass and set up shop in Leadville. Nobody seemed to need a doctor, however, and Dougan sat in his office for 28 days without a customer. On the 29th day he received word that there had been a mining accident and he was needed immediately. -That was the begin¬ning of his illustrious career in Leadville. Dougan was a successful physician, became mayor in 1881 and was later president of the Carbonate National Bank. Leadville was a simple community of log structures in 1878. By June of the following year, however, it had blossomed considerably. According to Cass Carpenter, as of May 1,1879, Leadville had "...19 hotels, 41 lodging houses, 82 drinking saloons, 38 restaurants, 13 wholesale liquor houses, 10 lumber yards, 7 smelting and reduction works, 2 sampling works for testing ores, 12 blacksmith shops, 6 livery stables, 6 jewelry stores, 3 undertakers and 21 gambling houses where all sorts of games are played as openly as the Sunday School sermon is conducted." Additionally, there were 36 brothels. When George E. King and other architects arrived, Leadville took on an air of elegance and sophistication. In sharp contrast to some of the Victorian-style, gingerbread-laced homes in Leadville, its suburbs were comprised of many tenement shacks and plain cabins mixed with a few commercial buildings, many mines and smelters. Mines sprinkled the area east of Leadville like pepper from a pepper shaker. Wherever there was a cluster of mines, a camp usually sprang up. Most were very close together. South of Leadville the giant Arkansas Valley lead smelter sprawled out between Stringtown and Bucktown in an area known as Smelter Valley. Founded in 1879 as the Billing and Eilers Smelter, the Arkansas Valley plant was operated by the American Smelting and Refining Company. Several other smelters operated in the vicin¬ity. In April 1878, Horace Tabor grubstaked prospectors August Rische and George Hook. For $64 worth of supplies and tools, he was guaranteed a one-third interest in their findings. Rische and Hook discovered the Little Pittsburg (often spelled Pittsburgh) Mine and made Tabor an instant millionaire. Tabor once purchased a "salted" mine, the Chrysolite; but instead of considering it a bad deal, he further developed the property and struck rich silver ore. Later, Tabor purchased the Matchless Mine for $117,000, possibly the only investment he made without partners. During its peak years, the Matchless yielded $1 million worth

Jan 1, 1998