Search Documents

By W. –E. Marx, M. Faber, R. Pollak, I. Astberg

INTRODUCTION Essentially three strategies are pursued in parallel for protecting the underground working force in mining against the consequences of methane ignitions which might lead to explosions: • Sufficient ventilation for avoiding the formation of explosive methane-air mixtures. • Avoiding sources of ignition caused possibly by electrical equipment or friction. • Structural explosion protection for limiting explosion propagation to the farthest-going extent for the case that methane is fired because of failing of the above preventive measures taken. The corresponding methods taken in mechanized roadheadings with point-attack roadheaders in German coalmining are subject of this paper. VENTILATION In ventilation of roadheading sites the following is to be considered in respect of methane control: • Sufficient air flows by volume being cycled to the heading face for diluting released methane to safe concentrations. • Sufficient local air velocities for effective mixing of methane and air in the whole heading site, in particular directly on the heading face and underneath the roof. Furthermore, ventilation needs to be laid out in a way that cut- ting does not result in health affecting dust exposure at any working place. Accordingly, the ventilation systems shown on Fig. 1 including primary and, if necessary, secondary auxiliary ventilation air ducts as well as dedusters, are used in roadheadings. This equipment is run according to the following principles: • If the roadheader is at standstill, the heading face is ventilated by the free air jet from the blowing duct closest to the face. In this operation phase the deduster is shut-down. • During cutting, the exhaust of the blowing air duct is automatically closed, and the deduster is taken into operation. The in- coming fresh air is now locally discharged via a lateral orifice, or distributed by Coanda-type ducts from the primary or secondary ventilation air duct. In this way, a stable dust wall not disturbed by the jet of the air duct is formed in front of the heading face. Only the ventilation air stream taken in by suction of the close-to-face deduster is passed through the inby zone of the heading face (over approx. 20 m). The clean exhaust of the deduster is dischayed to the roadway in some distance outby. Immediately at the heading face, methane accumulations possibly released by cutting are diluted by compressed-air jets from air-movers located near the roof which assure more rapid motion of the air without distuhing the dust wall. • In the zone of overlapping of primary and secondary duct and the deduster - that zone possibly is poorly ventilated during cutting - sufficient local air speed is assured by Coanda-type ducts or additional ventilation jets for avoiding methane accumulation. The regulations of the inspectorate specifies geometrical conditions to be met with these configurations of ventilation equipment. In-seam roadways are ventilated at rates > 0,5 m/s. For dedusters, present-day ventilation air flows are of 600-800 m+/ min. Ventilation monitoring and control is assured by units for measuring methane and ventilation air flows. If pre-set thresholds are exceeded or fallen short of, these measuring units shut-down - dependent on potential hazard - any not intrinsically safe electrical equipment in the roadheading, either totally or in limited zones. In addition, CO-measuring units near the roadway en- trance serve for early detection of mine fires. In spite of this ventilation layout and the equipment used and in spite of the water spray systems on the cutting head (discussed later in this paper) several cases of methane ignition and subsequent burning off (however, no explosions) have been recorded in the recent past. Therefore, the above-described ventilation is nowadays complemented in many cases by machine-mounted ventilation equipment for the immediate surroundings of the cutting head. Ventilation of the surroundings of the cutting head Investigations carried out subsequent to the above-mentioned gas ignitions have shown that the high ventilation air speed necessary for rapid dilution of methane could not permanently be arrived at in the following zones: • The direct zone of cutting, in particular during sumping. • The floor zone above the debris, predominantly below the cut- ting head. Accordingly, VOEST ALPINE-Bergtechnik, a producer of mining machinery, in cooperation with DMT developed for point- alttack roadheaders a novel machine-mounted ventilation equipment, the Jet-Block" (AERO SAFE Jet-Block) shown on Fig. 2. This system allows to ventilate the above-mentioned critical zones with high flow speeds. One AS Jet-Block is mounted on each side of the boom approx. 0.5 m behind the cutting head. The blocks discharge compressed-air jets with high energy from 10 nozzles per block into the hazardous zones (Fig. 3). Two nozzles of each jet block are tangentially oriented toward the upper circumference of the cutting head, the others are arranged fan-like with orientation to the heading face underneath the cutting head and the debris. The nozzle array of the blocks as well as the com-

Jan 1, 1997

By Damien Gaboury

"Two practical methods for correlating two or more diamond-drill core intersections, using a stereographic projection software are presented. The first may be used to establish if two or more vein intersections are correlative, based on their core angles and diamond-drillhole attitudes. The second method allows prediction of main vein attitudes from numerous intersections, based on a spherical density contouring projection. The methods are suitable for: (1) correlating veins in complex orebodies; (2) ascertaining lateral continuity of ore for reserve estimations; (3) demonstrating the hidden complexity of an orebody; and (4) correlating and interpreting various planar elements.IntroductionModern mineral exploration relies on diamond- drill core data and on the ability of geologists to interpret them. Drill core generally yields unoriented information, unless an expensive orientation device is used. As a consequence, strike and dip of planar elements such as lithological contacts or mineralized veins cannot be determined easily. This is particularly true for blind deposits (covered by thick overburden) and complex orebodies, where field data cannot support drilling interpretations. Such a problem has been addressed previously using two and three diamond drillholes and several solutions were proposed based on trigonometry, and geometric and stereographic projections (Mead, 1921; Wisser, 1932; Fischer, 1941; Stein, 1941; Bucher, 1943; Gilluly, 1944; Addie, 1962; Mills, 1963; Lyons, 1964). However, these solutions are time consuming and not relevant to present day computerized data plots."

Jan 1, 1997

By D. J. Farmer

Mining hoists are major components of any underground mine, however, the detailed design work required to get the actual power required for a particular hoist is outside the scope of preliminary feasibility studies. Nonetheless, a hoist is costly. Therefore, an accurate estimate is needed for the design parameters and the power required. There are two methods available, namely, the O’Hara method and the Society of Mining Engineers’ method. Tests were done for both methods employing nine friction hoists and 19 drum hoists currently in use at Canadian mines. The O’Hara method provided unacceptable results for both friction and drum hoists. While, the SME method was designed for American regulations and factors of safety which often differ significantly from Canadian ones, good results were obtained. The two relationships deter-mined were simply to add 5% to friction hoist design and to add 4% to drum hoist design. Modifying the SME method by these two factors will allow the hoisting system determined by the SME method to be within the error for a prefeasibility study.

Jan 1, 1997

By A. Deneys

An experimental technique has been devised for studying the reaction kinetics of the reaction: ZnO + 2Fe0 = Zn(g) + Fe203, by which zinc evolution can occur from a molten slag bath in the absence of a carbonaceous reductant. When studying the reaction kinetics by heating from room temperature, solid state reactions and poorly defined melting points may obscure the starting point of the reaction. In order to eliminate this problem, an experimental technique was devised whereby two molten slags could be melted independently, and then mixed, to provide a well defined starting point from which to begin taking measurements. Two crucibles were mounted in a vertical reaction cylinder. The upper, mild steel, crucible had a bottom pouring plug which was sealed by a steel stopper rod. A fayalite mixture was contained in this crucible. The lower crucible contained an A12O3-CaO-SiO2-ZnO solution. Once the two slags had been melted, the steel stopper rod was removed from the upper crucible. The upper, reduced slag (fayalite in equilibrium with the upper steel crucible), drained into the lower crucible where the two slags were mixed by submerged argon stirring. Dip samples were taken to measure the zinc content of the final mixture as a function of time. The experimental procedure will be described, as well as results of experiments which were conducted on synthetic slags. The system investigated was similar to the lead blast furnace slag which is produced by the primary lead smelters of Missouri, USA.

Jan 1, 1997

By R. Llewellyn

"Wear damage is responsible for very high maintenance costs and significant production losses in the oil sands industry of northern Alberta.It affects all areas of operations and involves a panoply of wear mechanisms from low stress sliding abrasion at extremely frigid temperatures during winter mining, to elevated temperature erosion/corrosion in processes where bitumen is converted to lighter hydrocarbon products.There is no universal panacea to defend against such diverse attack and a wide selection of resistant materials and systems is employed. These range from relatively soft rubbers which rely on their elastic properties for their protective capability, to some of the hardest ceramics and cermets which are currently available commercially.Details are presented of the characteristics and forms of the variety of wear materials being used and how they relate to the requirements of their areas of application. The review focuses on the practices followed at Syncrude Canada Ltd., which is the larger of the two commercial oil sands plants."

Jan 1, 1997

By H. Polat

Relatively large amounts of such hydrocarbons as fuel oils are often needed in flotation of low rank coals. The amount of oil can be decreased considerably by using surfactants as promotors. The reagents which are good candidates as surfactants to promote hydrophobicity can also act as emulsifying and wetting agents. Since the physical and chemical variables influence various sub-processes in different ways, their influence on the performance parameters is complex. The results of laboratory tests are presented to show that the dual role of reagents can be judiciously exploited to increase both the recovery and grade of clean coal. The mode and order of reagent addition is critical in enhancing their efficacy as flotation promotors. The results demonstrate the benefits of proper conditioning of the pulp prior to flotation.

Jan 1, 1997

This chapter describes the adverse health effects associated with exposure to respirable coal mine dust. Epidemiological studies of underground and surface coal miners in the United States and other countries are discussed. Also discussed are animal studies that add to our understanding of particle deposition and retention in the lungs and associated disease responses. This chapter emphasizes studies that (1) were performed since the passage of the Federal Coal Mine Health and Safety Act of 1969 [P.L. 91- 173], (2) used standardized methods of exposure monitoring and disease classification, and (3) investigated exposure-response relationships between respirable coal mine dust exposure and disease. Several published review articles contain further discussion of health effects studies of coal miners [Attfield and Wagner 1992b; Petsonk and Attfield 1994; Cotes and Steel 1987; Merchant et al. 1986; Morgan and Lapp 1976; Morgan 1975].

Jan 1, 1997

By D. F. Malan

In deep level hard rock mining the rheological behaviour of the rock is important as time-dependent aseismic processes can lead to a stable dissipation of energy thus reducing violent outbursts. Underground closure measurements, observations of time-dependent fracture formation and siesmic data indicate that the rock in deep South African gold mines shows significant time-dependent behaviour. The objective of this work is to quantify the time-dependent rock behaviour for laboratory specimens and underground conditions. Laboratory experiments indicated that lava and quartzite specimens undergo measurable creep strain at stress magnitudes below the failure stress. Quartzite is however prone to more significant creep at lower stress levels. A viscoelastic analysis showed that laboratory creep results can not fully explain the behaviour observed underground. The in situ behaviour is governed mainly by the rheological behaviour of the fracture zone and the resulting time-dependent formation of new fractures. A viscoplastic discontinuity model implemented in a boundary element program is used to simulate this behaviour.

Jan 1, 1997

By Clarence Zink

The need for continual process improvement and innovation to reduce operating costs in the mining industry extends to the first significant encounter all production miners have with the rock: drilling blastholes. Material and design advances alone have greatly increased the productivity of today's tricone blasthole bit over bits used just a few years ago. Significant additional operating savings are being realized by utilizing improved air practices on blasthole drills, and by selecting drilling equipment designed to provide optimum air volume and pressure at the blasthole bit.

Jan 1, 1997

By M. R. Stokes

Over the recent years there has been an increase in the application of retreat mining on longwall faces as mine operators strive for ever greater productivity. The purpose of this paper in then to review current practice as a starting point and then move forward to discuss the future geometry's that a longwall face may take. Single and double production zone three roadway faces are assessed. All possible configurations of three roadway faces are defined. Unsuitable configurations are rejected after analysis of broad ventilation issues. The remaining configurations are then assessed on an operational basis, this includes: limits on retreat synchronisation, structure of centre gate, floor bulging and equipment installation. The remaining viable configurations are then further assessed on ventilation issues, this includes: provision for gas control/gas fringe, face climate and balancing of face flows. Possible face climate is assessed using numerical simulation of the various configurations, the predicted dry/wet bulb temperature and predicted levels of heat stress indices are given and discussed in detail, along with face flow balancing. The necessary conditions required for the successful operation of a double production zone three roadway face system are formulated, together with conclusions as to the possible level of application.

Jan 1, 1997

By Bernie W. Martin, Raymond Leray, Christian Criado

Aguas Argentinas,1 a consortium managed by Lyonnaise des Eaux of France and operator of the world’s biggest privatized water supply and waste water collection system for the City of Buenos Aires, a city of 9 million people, was faced with the daunting task of providing new service to 1.6 million more people in the first five years of their 30 year concession. Aguas Argentinas elected to use the Negotiated Compressed Process - NCP - for the fast track implementation of a 15000 meter, 3,5 meter diameter tunnel, a key component of the infrastructure master plan. NCP was developed by Klohn Crippen for the $200 million international railway tunnel between Canada and the United States. The conceptual design of the project was performed by Safege Montgomery-Watson, who engaged Klohn Crippento assist with the NCP, the preparation of the tender documents, and implementation of theproject during construction. The process included the purchase by the client Aguas Argentinas of two sophisticated 4 metre diameter earth pressure balance tunnel boring machines from Herrenknecht of Germany. Construction of the tunnel is being performed by the consortium Wayss & Freytag (Germany) and Sollazzo Hnos S.A. (Argentina). The water tunnel is being built with a one pass, bolted segmented gasketed reinforced concrete liner. The purpose of this paper is to describe a transferable methodology for this innovative contracting procedure, the project organization and quality control plan for this important world class tunnel project which is designed to service one of Latin America’s largest metropolitan areas.

Jan 1, 1997

By Joseph Lynch, John DiPonio

This report refers to the Chicago Deep Tunnel Contract 13A, which was the first contract let in the City of Chicago requiring the construction of deep drop shafts for the transportation of high level sewage to the deep tunnel system. The basic contract required the contractor to construct certain drop shafts designed to deliver surface and high level sewage to the deep tunnel system approximately two hundred feet below. The design of the drop shafts was in a degree affected by their proximity to the existing deep tunnel. The tunnel, approximately three and one-half miles long, was to have five shafts dropping sewage at five locations. Four of the drops were approximately one-half mile apart and spaced from the dead end of the tunnel. One shaft divided the remaining two miles from the existing work shaft at the southeast end of the tunnel wherein a 220' deep pumping station was to be built. The existing tunnel had been built some time previously and all dewatering had stopped, allowing the tunnel and main shaft to fill with water. According to the plans, the drop shafts were all between fifty and ninety feet north or south of tunnel center line, and located in heavily built-up residential and industrial property. This then defines the problems: How do we control the water. If we excavate from the top down, how do we handle the slurry and the muck from five locations. How shall we construct the connecting tunnel between

Jan 1, 1997

By J. Ling, L. Racine, P. Cousin, A. R. Laplante

"The problem of gold recovery by gravity from high density gangues is first discussed from a fundamental perspective. Three potential difficulties are presented: poor liberation and fine gold particle size, concentrate bed erosion by coarse dense particles, and slow percolation of gold particle through the high density gangue bed. Two case studies are presented to illustrate the impact of these three problems on circuit performance and the feasibility of gravity recovery. It is concluded that careful testing can determine the scope of the first problem and feed preparation can limit the extent of the second. The third problem is clearly the most serious and results in lower gravity recoverable gold recoveries than would be achieved with the same recovery effort on a low density gangue application.IntroductionSince the commercialisation of the Knelson Concentrator in 1980, gold gravity recovery has experienced a surge in interest, in Canada and the United States first, then Australia, Zimbabwe and Russia, and finally worldwide. Table I details number of units sold in various countries, which corresponds approximately to their importance as gold producers 1. Exceptions. such as the low rank of South Africa or the importance of Zimbabwe, despite the much higher gold throughput of the former, are generally the result of differences in the effectiveness of the local marketing strategies, as well as a reflection of the ""philosophy of recovery"" prevalent in the country.The impact of the Knelson has not been felt equally in all plants. Typically, a highly successful application falls into the following categories: (a) alluvial or hard rock recovery for which gravity is the sole recovery method, (b) hard-rock free gold milling with ores which have a very high gravity-recoverable gold (GRG) content, (c) low grade sulphide copper-gold ores which include flotation ahead of cyanidation and (d) free-milling gold ores ahead of Other applications can be successful, but are not as common. The ""explosion"" of centrifuge concentration, of which the Knelson is the most successful but by no means the sole model, has created a certain euphoria which can be summarized as ""gravity recovery will improve the profitability of gold milling, no matter what."" This presentation is about applications that are not so successful, or even downright unsuccessful. The rationale is not to down-play gold gravity recovery, but to set it in its rightful position: metallurgically, it is not appropriate all of the times; it can become inappropriate if poorly designed; and it can be metallurgically possible but economically unjustifiable. In this paper, this will be illustrated and explained rather than demonstrated, with the use of both industrial plant surveys and laboratory test work. Alternate gravity approaches will be suggested."

Jan 1, 1997

By Ron Frye, Carl Liibbe, Wayne Curtis, Julie Pecori, Dan Leach

Test work comparing the performance of a Low Density Porous Ammonium Nitrate Prill to regular Porous Ammonium Nitrate conducted in Pennsylvania and New York showed that less ammonium nitrate was required to perform the same work and that improved sensitization of an emulsion/ammonium nitrate blend reduced “orange fumes”. Fragmentation was similar in all tests with improved heave and throw experienced.

Jan 1, 1997

By N. Behnood, W. Pascheto

"Laboratory wear tests are important tools that can be used for the evaluation of materials for wear applications and mitigation of wear problems in the mining industry. However, laboratory test parameters must be fully characterized and test results must be carefully interpreted if a material selection is to be made. Failure to do so may lead to erroneous conclusions. Suitable lab-oratory tests are valid only if they reflect the field conditions to which materials are subjected. Therefore, it is important to know, in detail, the field conditions, as well as the wear test techniques being considered. It is important to recognize the limitations of the various wear tests and the wear test data published in the literature. This work will review present wear testing technology, including the various wear tests avail-able, wear test equipment and test limitations. Several wear test procedures will be related to common equipment used in the mining industry.IntroductionThis paper will concentrate on non-lubricated wear mechanisms, because they are the most costly to the mining industry. Very frequently we are faced with the task of selecting materials for wear applications or improving existing systems that are giving poor performance. There are plenty of examples in the literature of practical wear cases and ranking of materials for wear applications. It is also very common to find materials manufacturers’ data -sheets listing wear tests results by comparing their materials performances against those of competitors. Much of the published wear data lack the description of the type of wear test, test parameters and the type of wear mechanism to which the data should be applied (if any).Before considering wear test data for a specific problem one should ask which type of wear mechanism is involved? What type of test and what test parameters were used to produce the results? Even if the type of wear tests and parameters are known, how accurate and useful are the published wear data? How are the results related to a particular type of wear? It is important to point out that even the standardized wear tests, such as those in ASTM standards, have limitations. Such limitations are recognized and clearly spelled out in the standards themselves. Basically, wear tests may lead to erroneous results if the test is not able to repro-duce the same wear mechanisms encountered in the field. Therefore, the use of published results may be helpful, as a starting point, but may be of little value for a final material selection.This work will discuss the main types of non-lubricated wear mechanisms encountered in the mining industry. In addition, it will discuss the many wear tests available and their correlation with the various types of wear mechanisms. The limitations of several standardized wear tests and the limitation of using published wear data will also be discussed."

Jan 1, 1997

By Kumara Rachamalla

North American mining companies are lagging behind their global competitors in participating in the outstanding opportunities in India. The Indian government has liberalized foreign equity participation in the mining sector by up to 50% and, in some cases, even higher. Delegates from Europe, North America and South Africa learned this at an information seminar held in London, England, Attendees were welcomed by L.M. Singhvi, the UK's high commissioner for India. He introduced a government of India delegation headed by B.P. Baishya, minister of steel and mines. Singhvi is an eminent jurist and leading constitutional expert. He reiterated the soundness of India's legal system. He also outlined the recent Investment Protection Treaty between India and the United Kingdom. Baishya emphasized thee geological diversity and strengths of India's domestic market with its population of more than 920 million people the second largest in the world after China and its reservoir of skilled labor. He also outlined the potential of India's untapped natural resources. The private sector is the backbone of the Indian economy. It accounts for 75% of gross domestic product (GDP). The current minimum program of the new United Front government envisions 12% growth in the industrial sector, 7% in GDP and direct foreign investment of US$10 billion a year. "Mining is an area that can attract a sizable part of this investment," Baishya said. "Projected growth of the Indian economy will require increasingly large quantities of basic raw materials, such as coal and base- and precious-metals to meet the needs of domestic and export markets." Administration of India's mining sector is divided into the Ministry or Mines for regulating and developing the country's mineral resources, five public sector Mining Enterprises, the Geological-Survey of India (GSI), the Indian Bureau of Mines (IBM)and 25 states and seven Union Territories. The GSI is the second oldest (founded in 1851) and the third largest organization of its kind in the world, Baishya said. It has geologically mapped more than 90% of India's 3.2 million kmz (1.2 million sq miles) at a scale of 1:50,000. Several promising mineral projects have emerged from regional exploration programs conducted by GSI and the Mines and Geology State Governments. IBM recently completed a national mineral inventory. It covers 13,000 deposits/prospects of 61 nonferrous minerals. GSI also compiled a similar inventory on 61 coal fields. India is attractive to exploration companies for several reasons. These include favorable geology, accessible locations and a large mineral database. India also has many experienced geoscientists with well-equipped and efficient laboratories, Baishya said. Secretary to the Ministry of Mines A.C. Sen emphasized the largely untapped-geological and mining potential of India. He also discussed the new vistas that have opened up opportunities for exploration and mining. India has large quantities of mineral reserves, Sen said. Its vast Precambrian Shield - like those in Canada and Australia - is endowed with gold, platinum group and base metals, as well as coal and industrial minerals. Annual mineral production is valued at more than US$7 billion. Sen pointed out that India is the largest single consumer of gold. And domestic gold prices command at least a 20% premium above international prices. Recent diamond, gold and base-metal discoveries and prospects uncovered by GSI have generated investment interest from abroad, he added Delegates heard that the Indian Constitution gives the central government the job of framing legislation and the regulation and development of minerals. This ensures that mineral laws are uniform throughout the country. However, the right to grant mineral concessions, such as prospecting licenses and mining leases, rests with the minerals' owner. In India's case, that is the state government. The Indian government has formulated several guidelines that regulate the granting of prospecting licenses for large areas. ? The central government will consider the requests of state governments for the granting of prospecting licenses for areas exceeding 25 kmz (9.6 sq miles). But the license must include a provision to conduct aerial prospecting of the area. ? Any prospecting licensing area should not exceed 5,000 kmz (1,930 sq miles). for a single license. And the total area held by one company should not exceed 10,000 km2 (3,861 sq miles) for the whole country. ? The grant of larger areas will be linked to a mini- mum expenditure commitment on physical targets. State governments will monitor these expenditures. ? The granting of large areas for prospecting will be linked to a schedule of relinquishment.

Jan 1, 1997

By R. R. Jozefowicz, T. X. Ren, J. S. Edwards

The control of methane emission into underground mine workings is important both for the safety and productivity of the mine. As deeper and gasser coal seams are mined, ventilation methods involving increasing air pressures and quantities across mine workings may not be able to cope consistently with methane emission rates during the production cycle. An accurate prediction of methane emission into mine workings is of great significance in the design of ventilation systems and additional methane control methods if required. Research has been conducted to develop a numerical method for simulating methane flow through strata in which permeability is strongly influenced by mining-induced stress. To achieve this objective, both numerical modelling using Computational Fluid Dynamics (CFD) and laboratory tests on rock samples and granular materials under triaxial stress condition were carried out. Correlation has been established between stress and permeability characteristics of rock-measure rocks and laboratory results are being incorporated into the CFD models. This paper introduces the use of CFD techniques to model methane flow through permeable strata around longwall coal faces currently undertaken at the University of Nottingham.

Jan 1, 1997

By G. F. Revey

Most commercial explosives contain from 70% to 94% (by weight) ammonium nitrate. When some of the explosives end up in shot rock and ore, through either spillage or incomplete detonation, ammonia and nitrates can leach into the ground water. In recent years, state and federal regulators have applied more stringent water-quality standards, particularly at new mines and development projects. When mining conditions permit, bulk ANFO, a mixture of ammonium nitrate and fuel oil, is the explosive of choice. ANFO is less costly than other explosives but it dissolves readily in water. Several case histories in the United States and Canada show a clear connection between uncontrolled losses of bulk explosives and high nitrate levels in mine effluents. Mining companies have tried several approaches to reduce ammonia and nitrate levels in groundwater. These approaches range from controlling explosive losses to treating the mine effluents. In this paper, controlling explosive losses is addressed For both packaged and bulk explosives, guidelines to limit losses during storage, handling and use are described in detail.

Jan 1, 1997

By G. J. Hartman

The Fort Cady in situ borate mining project involves recovery of boron from a mineral deposit located over 1400 feet below the surface. The resource recovery method is being developed using in situ mining technology employing weak acid solution injected directly into the ore body. As the acid contacts the calcium based ore (primarily natural colemanite), the contained borate values are digested as boric acid. This boric acid solution is then pumped to the surface by use of submersible pumps. At the surface the borate values are recovered as a finely divided solid white powder after a series of chemical reactions and precipitations resulting in the production of calcium borate. The refined product is then sold under the trade name CADYCAL 100.TM All environmental permits for up to a production rate of 90,000 tons per year have now been obtained. These permits required an Environmental Impact Study (EIS) for federal lands and an Environmental Impact Report (EIR) for the private portion of the property. Regulatory permitting took over 5 years to obtain all authorizations for this operation. The ore body has an average thickness of 118 feet extending over 273 acres. At a production rate of 90,000 tons per year with only a 70 percent resource recovery allowance, in place reserves are sufficient to sustain production for over one hundred years.

Jan 1, 1997

By V. B. Achanti, A. W. Khair

Developing a laboratory procedure for the determination of coal-seam compressive strength has been a subject of discussion for many decades, and the reliability of laboratory determinations is often the subject of debate. A coal seam’s characteristics, the method of sample collection, the specimen preparation method and the testing procedure can often result in drastic variations in the test results. In this paper, the development of a laboratory testing procedure for the determination of coal-seam compressive strength is presented. Two samples that were collected from different coal seams were tested in this study. First, the inherent characteristics, i.e., coal structure. Hardgrove grindability index (HGI), Slake durability index, proximate analysis and mechanical properties (Young's modules and Poisson's ratio), of each coal were determined. The results were used to categorize the coal scams in terms of the characteristics liable to produce variable strength data in typical laboratory tests. Second, two commonly used laboratory specimen shapes, cylindrical and cubical, were tested to determine which shape produced the most reproducible strength values. Third, four loading rates within the static testing range, i.e., 0.007, 0.07, 0.34 and 0.7 MPa/s (1.0, 10, 50 and 100 psi/sec), were used to determine the ideal loading rate. Finally, the number of test samples required to produce strength data within the acceptable standard deviation, considering coal seam characteristics, were established. Background Laboratory testing of coal specimens for the determination of seam compressive strength has been a subject of discussion since the early 1900s. Many researchers have tested coal specimens to estimate coal-seam compressive strength for use in pillar design to insure the safe operation of [ ] mines (Unrug et al., 1986; and Hirt et al.. 1992). Yet, there is a lack of a universal procedure, and, no matter which approach is used, it becomes the subject of intensive debate. A great deal of work has been performed on the subject, and there is much information available in the literature. Some of this work concerns quantifying the influence of specimen shape and size on compressive strength (Bieniawski. 1968: Barron et al.. 1992: Khair and Xu 1994; and Khair 1994). As indicted in the literature, coal is a heterogeneous material, consisting of discontinuities such as cleats and bedding planes, which are likely to produce variable strength results (Holland, 1964; Unrug et al., 1986). Some of the prominent issues that influence the determination of coal-seam compressive strength in the laboratory are: •the collection of a representative sample from a coal seam; •the geometry, i.e., shape and size of the specimens to be prepared and tested: •the loading rate at which the specimens are to be tested:

Jan 1, 1997