Search Documents

By Chris Uys, Johan Labuschagne

Sishen Iron Ore Mine, located in the Northern Cape, is an open cast mine excavating approximately 100 million tons rock to produce 25 million tons of high grade haematite ore per annum. The size of the pit is approximately 12 km ‘1.5 km ‘150 metres. The final depth is planned to be around 350 metres. It is hard rock mining operation employing the conventional truck and shovel method. Mining benches are twelve and a half metres in height and are divided into blasting blocks, each consisting of approximately 300 000 tons of material.

Jan 1, 1997

By F. E. Wagner, L. J. Cabri, Y. G. Safonov, N. S. Bortnikov, A. D. Genkin, J. Friedl, G. N. Gamyanin

"A multidisciplinary investigation (including INAA, SIMS, EPMA, and Mossbauer Spectroscopy) was used to characterize gold in four of the largest Siberian mesothermal sulfide gold deposits. These are the Olympiada (""'750 metric tons gold) and Veduga (estimated at 75-100 metric tons gold) deposits in the Enisei Mountain Range and the Nezhdaninskoye (z500 metric tons gold) and Sentachan deposits in the Verchoyansk-Kolyma area. It was found that some of the mineralization is refractory in all four deposits, largely due to the occurrence of ""invisible"" gold in arsenopyrite as well as within pyrite, but with a lesser concentration. The gold concentration and its distribution varies considerably both within and between arsenopyrite grains, with implications for processing options such as heap leaching. The ore most likely to be amenable to heap leaching is the oxidized ore of the #4 orebody of the Olympiada deposit, but further quantitative mineralogical investigations are recommended for this orebody's sulfide ore and for the ores of the Nezhdaninskoye deposit. Following a full mineralogical characterization, it is possible that economic viability will depend on a combination of pre-concentration with or without pre-treatment, followed by heap leaching of some tailings products.Acknowledgements· The Russian authors performed this study under an ""Eco res"" Project which was financially supported by the Ministry of Science and New Technology of the Russian Federation. C.J. Stanley wishes to thank John Spratt and Terry Williams for help with EPMA. F.E. Wagner acknowledges the Deutsche Forschungsgemeinschaft for a grant supporting the Mossbauer studies. L.J. Cabri is grateful to the following: M. Beaulne, D. Carson and J.H.G. Laflamme for technical support, K.E. Haque for technical comments, and D.M. Hausen and W. Petruk for editorial suggestions."

Jan 1, 1997

By Richard D. Begley

This paper will present the results of an analysis of several abandoned coal mine projects and includes field data for over a dozen different reclamation projects recently completed in the state of West . Virginia. The analysis was performed with the objective of summarizing and or classification of the environmental consequences with reference to the characteristics of the mining facilities (surface, underground, etc.). The analysis also addressed the itemized cost of remediation with respect to procedures, environmental concerns and time. The results of the analysis are that each abandoned coal mine site in West Virginia have/had many unique features and in most cases include a combination of environmental concerns that complicate comparisons. The study also revealed that the abandoned mine land program for mines abandoned prior to 1977 that is being financed by a tax on the production of coal, has produced many benefits for the state of West Virginia. This grant program administered by the Office of Surface Mining, has resulted in a high quality methodology of remediation that has been successful for many years in greatly minimizing and/or eliminating environmental concerns from abandoned coal mines.

Jan 1, 1997

By R. J. Sawyer

The Greens Creek underground polymetallic mine restarted production in 1996 from a newly discovered high grade ore zone. Efforts to improve payable gold recovery have focused on gravity separation. The paper compares testwork and plant results for a newly installed gravity circuit.

Jan 1, 1997

By P. T. Velu, R. G. Reddy

"The use of emf measurements to derive classical thermochemical data has been in use for many years. The reaction associated with electrochemical process is harnessed in a galvanic cell and energy involved measured in terms of electromotive force. The property requirements of sensor electrodes used differ for various aqueous, molten salt and solid electrolyte systems. The electrodes for molten salt electrolytes need special care for construction. This paper describes the studies carried out using an Ag/ AgCI reference electrode. This electrode was used to measure the solubility of compounds in molten salt electrolytes. The results obtained using this electrode are in excellent agreement with the values from chemical analysis method.I. IntroductionThe technique of obtaining a metal from its oxides by electrolysis is more than a century old process now. In these processes, it has been well established that for halide electrolytes, only the dissolved oxides are available for the dissociation at the electrode to release the metal during electrolysis. Therefore, the solubility of metallic oxides in the molten salt electrolytes is an important parameter which determines the economical and technical viability of these processes. The widely used molten salts systems in halides are fluorides and chlorides. The fluoride electrolyte system is used in our present study.The viability of obtaining aluminum alloys by in-situ electrochemical processing has been outlined in our earlier publications[1-8]. Studies on the solubility of various alloying element compounds is a part of our ongoing research efforts for the direct production of Al-Li alloys. As mentioned above, the solubility of lithium oxide and lithium carbonate compounds in molten fluoride electrolyte system have studied using EMF technique. The change in potential of the molten electrolyte was measured by a working electrode against the reference electrode with the addition of lithium compound."

Jan 1, 1997

By Dennis R. Barratt

Rockbolting is now used extensively as a method of primary support in UK coalmines. Over the past fifteen years an optimum bolting system has evolved, based on a high grade steel bolt and a very strong stiff resin. Where necessary, cablebolts are used in conjunction with rockbolts as a supplementary means of support. The rockbolting system, as currently used, is based on a maximum bolt length of 2.4 m whilst cablebolts are generally 6 or 8 m long. Based on the UK experience, there are situations where it is necessary to extend the bolted horizon above that normally achieved with a 2.4 m long rockbolt. Until recently the only options available were coupled rockbolts or cablebolts, both of which have inherent problems in terms of installation. Flexible Strand Rockbolts (FSR), in lengths of 4 to 6 m, provide the means of being able to extend the normal bolted horizon Other advantages include increased strength characteristics (tensile and shear), able to be installed in the UK standard hole size (26-28 mm), encapsulation using resin capsules, thus offering immediate support, high bond strength compared to conventional strand, and able to be installed using existing drilling and bolting equipment. The FSR is considered to be a new concept in terms of strata control and one that compliments the rockbolting system currently in use.

Jan 1, 1997

By Dunne RC

The physical properties of an orebody require determination for virtually all mining projects, new and existing. The extent and regularity of such determinations being subject to the size and homogeneity of the orebody. Such properties have an impact at the design stage of new plants, with respect to equipment specification, and thus effects capital costs; and also impacts on the operating costs of new and existing plants, with respect to power consumption, production levels and part replacements. All of these can severely alter the bottom line and can be the determining factor in the economic viability of many projects.This paper examines some of the most common properties that are measured, the procedures utilised in determining these properties, and their variability under conditions of reproducibility, and to a lesser extent repeatability.

Jan 1, 1997

By Kim M. Cornelius

Musculoskeletal injury is a term used to describe a wide range of soft tissue disorders which affect the nerves, tendons, and muscles. Common examples include lower back pain, tendonitis, and carpal tunnel syndrome. The majority of these injuries are not the result of sudden mishaps, but usually develop gradually from repeated wear and tear. Symptoms may first appear after weeks, months, or even years. Symptoms may result from many types of activities, performed at work or at home, and it is often difficult to attribute a single event. In fact, it is more common to identify the factors which may have contributed to the development of the condition. The terms repetitive strain injuries or cumulative trauma disorders (CTDs) have been commonly used to refer to disorders that have occurred due to work related activities (Putz-Anderson, 1988; Fraser, 1989). Three main risk factors contribute to CTDs: force, repetition, and awkward postures. Any one or combination of these may contribute to the development of CTDs. Therefore, the design of equipment in conjunction with the required tasks should attempt to reduce these risk factors. Examining the layout of the work area to help identify tasks which may contribute to cumulative trauma is necessary. The following list(Putz-Anderson, 1988), describes ergonomic concerns that, overall, should be minimized at the work area:

Jan 1, 1997

Mine geologists have access to an economic mineral deposit, production parameters and secure exploitation title. They are well placed to understand ore formation and should contribute to the effective exploration of company mine property. Application of their special skills has been curbed by pre-occupation with production duties and by company re-engineering, including staff reductions. Contributions to exploration have been diminished and personal development inhibited. Modified management is required. Participation in mineral system studies and in exploration research comprise part of the basis for the re-emergence of mine geologists on the exploration scene. Changes in investment strategies in the minerals industry may create new employment opportunities. With regard to estimation of resources and reserves, the competence of practitioners who are incapable of disclosing their methods in transparent terms is under question. Ethical standards are also under public scrutiny because of some notable malpractice. Independent auditing may hecome more intrusive. While understandable in a market context, it reflects poorly on the profession. More substantial effort in public communications can improve the credihility ofthe industry and equip practising mine ceolouists for snider responsihility.

Jan 1, 1997

By Steve Colburn

The CRITERION Survey Systems utilize both theodolite mounted and hand held reflectorless distance meters. These are eye safe, easy-to-use, and specifically designed to endure the harsh environments characteristic to the mining, quarry and explosives industries. Survey data collected by the systems is digitally stored in a ruggedized data collector and then processed with a specialized, Windows-based, interactive software program which can be run on any standard PC.

Jan 1, 1997

By F. S. Knoll

Magnetic separation employing superconducting technology is now accepted within the Kaolin processing industry, proving the value of this technology and its ability to operate reliably even at the most remote site. Developments in superconducting magnet engineering, including cryogen free operation, combined with experience in mineral processing enables new forms of Wet and Dry superconducting magnetic separation to be developed. Applying the high magnetic force advantages at 5 T else available from such magnets to other materials is now a reality. High magnetic force mineral separating system developments are reviewed allowing the mineral processor to take advantage of a technology that is no longer confined to the laboratory.

Jan 1, 1997

By M. L. Leming

Introduction In the decades since silica gel was first identified in material exuding from cracked concrete, a great deal of research has been conducted regarding the chemical reactions between the alkalies found in portland cement and silica found in aggregates. The reaction is complex and one that is not yet completely predictable, especially from the point of view of developing specifications that are appropriate to all situations. This paper is not intended to be a rigorous review of the research findings but is an attempt to provide a simplified review of the mechanisms of the alkali-silica reaction (ASR), so that one can better understand the implications of the specifications, test results and effects on structures. In addition, the contractual relationships between the aggregate supplier and one of their major clients, the concrete supplier, will be examined with regard to the ASR. ASR basics Silica. Silica (silicon oxide) may exist in naturally occurring aggregates in various forms and in combination with a number of other elements. When the silica is completely crystalline, such as in quartz, it is chemically and mechanically stable. Quartz silica is impermeable and reacts only on the surface of the crystal, where the silicon and oxygen bonds are broken. Because the surface area per unit volume of most quartz is low, the reactivity is also low. Completely amorphous (noncrystalline) silica is, on the other hand, more porous and very reactive. The less "crystalline" the silica is in the aggregate, the more reactive. Silica that has melted and cooled quickly without recrystallizing, creating a glassy material (such as in certain volcanic aggregates), has a very low state of crystallization and will be much more reactive in an alkaline solution. Crystalline silica that has been transformed by heat and pressure may have a large quantity of strain energy stored in the crystal lattice. The presence of this higher energy will make the silica more likely to react. The "strained quartz" found in many metamorphic aggregates means that these aggregates are potentially susceptible to deleterious alkali silica reactivity, although the rate of reaction is typically much slower than with aggregates composed of or containing glassy or amorphous silicas. Another problem may exist with aggregates in which the silica is primarily crystalline. In aggregates such as chert, in which the silica exists as very fine crystals (i.e., crypto- or microcrystalline), the very high surface energies between the crystals contribute to alkali sensitivity. Therefore, the potential reactivity of an aggregate is seen to be a function of both the degree of crystallization of the silica in the aggregate and the amount of energy stored in the crystal structure, whether due to a large quantity of microcrystalline silica, a high strain energy stored in the crystals or some combination of these factors. The surface area per unit volume of the reactive silica will also affect the rate of reaction, because a larger surface area of reactive silica will have more opportunity to react. Obviously, the reactivity of the aggregate is also affected by the silica content. However, in this case, the results are not quite so obvious. A discussion of the effect of silica content will be postponed until after a discussion of the contribution of the cement paste. Paste characteristics. Hydrated portland cement is a very alkaline material with a pore solution pH typically in excess of 12. The alkaline environment of moist concrete provides an ideal place for noncrystalline or cryptocrystalline silica to react. However, not all alkalies are equal in their effects. Calcium compounds react with glassy silica to form calcium silicate hydrate, commonly abbreviated C-S-H a poorly crystalline material that can occur in several forms and chemical compositions. C-S-H was at one time called tobermorite gel, because it was chemically similar to the naturally occurring crystalline mineral tobermorite and because it had a gel-like (noncrystalline) structure when viewed under an optical microscope. The formation of C-S-H is the basis for both portland cement hydration and reaction with, for example, fly ash. C-S-H is relatively stable. Although drying will cause some shrinkage and rewetting will cause some expansion, the volume stability of the C-S-H is very good compared to the volume stability of most alkali silica gels. Alkali silica gels with high sodium contents, for example, are nonstable compared to C-S-H.

Jan 1, 1997

By D. Pacey

"This paper reviews the installation, start-up, and operation of a comprehensive monitoring and targeting management technique in which all plant utilities (i.e., electricity, natural gas, compressed air, and water) are managed as controllable resources in the same way that raw materials, mined ore, personnel and capital are managed.The essential elements of monitoring and targeting (M&T) include:•gathering in a systematic, disciplined way the utility information by energy account centres;•closely monitoring the utilities used in each centre and comparing them with production on a common time base (e.g., kWh/ton per day);•bench marking and target setting to pro-vide attainable energy reduction goals which can be further refined as they are achieved; and•establishing an implementation plant that may provide efficiency enhancing benefits to various operating areas within the plant.The M&T system will reduce utility consumption per unit of production on a continuing basis.This would translate into sustained operating cost and waste. M&T will also provide better information for assessing the plant operation and progressively implementing further enhancements."

Jan 1, 1997

By Bernard Woolley

The history of the use of calcium aluminates in mining is discussed including a review of very rapid hardening concretes, anchoring using cement capsules and pumped ground control systems. Specific reference is made to the long term performance of highly abrasion resistant orepass lining in South Africa and the use of rapid hardening materials for a range of applications in Australian coal mine where water infiltration creates difficulties or where rapid repair or return to service is required. The topics covered in detail are, high strength abrasion resistant concretes with a 20 year, 30 million ton ore pass life. Rapid reinstatement of wet and worn roadways using mineral dewatering and rapid roadway rebuild solutions, all in I maintenance shift. The different applications are illustrated using examples from operating mines.

Jan 1, 1997

By J. N. Eskilsson, W. P. Chen, J. L. Kaplin, V. S. Romero

The Massachusetts Water Resources Authority is currently improving its primary water supply system for the Boston Metropolitan area. The improvements planned by the Authority, which provides water for 46 communities and over 2.5 million people in eastern Massachusetts, include the MetroWest Water Supply Tunnel (MWWST) to provide redundancy in the transmission system, a large capacity water treatment plant and extensive covered storage facilities. The 28.3 km (17.6 miles) long, mostly 4.3 m (14 ft.) I.D. MetroWest Water Supply Tunnel will allow repair of the aging Hultman Aqueduct, which for 56 years has served as the transmission main from the water supply reservoirs to Boston. On completion of the tunnel, the old pipeline aqueduct will be repaired and brought back into service as a parallel, redundant transmission main. This paper describes design considerations and the design process for pressure tunnels in general and the MWWST in particular. It provides an overview of how the design of pressure tunnel and shaft components progresses.

Jan 1, 1997

Bigger is indeed better in today's surface mining operations. That is especially true regarding haul trucks. Building larger, "supersize" trucks, however, means designing more powerful engines and drive systems that are also more efficient and environmentally friendly. And miners are demanding that these trucks have longer service lives with minimum maintenance. So truck makers are teaming with engine manufacturers and mining customers to design these larger trucks that will ultimately lead to reduced mining costs. About 180 of those truck makers, engine designers and miners gathered in Tucson, AZ in September to discuss the state of haul trucks in today's mining environment. Haulage 2000 was sponsored by World Mining Equipment and attracted attendees from around the world. Manufacturers described the latest in haul truck advancements. These included the design of more powerful engines, improvements to mechanical and ac and dc drive systems and suggestions on how to reduce maintenance spending. Technology improvements in tires for larger struck was discussed as was the cost efficiency of new, lighter-weight bed liners. The following is a summary of a handful of the presentations.

Jan 1, 1997

By Paul C. Miclea

With the growing urban population and the concern for traffic congestion and pollution (emissions control), public transportation is becoming more and more attractive to both city dwellers and managers. To gain access to the central area of the city, the sub- way remains the most viable alternative, despite its higher cost when compared to above ground or elevated transportation systems. There are relatively few regulations and criteria for subway ventilation, particularly when compared with mine ventilation. The main document that provides guidance and general recommendations for subway ventilation and environmental control is the Sub- way Environmental Design Handbook, published in 1976 (2nd edition) by the U.S. Department of Transportation, Office of Re- search and Development. Many of the subway systems in existence today have been designed and built with ventilation features adequate for normal train operation, but their design does not consider stringent criteria for such emergency conditions as a train fire in a tunnel. The National Fire Protection Association's Standard for Fixed Guideway Transit Systems known as NFPA 130 as well as the ASHRAE Handbook - HVAC Applications (1995) provide specific design and operation requirements for subway ventilation systems. Some of the existing, old subways are upgrading their ventilation systems to comply with the new regulations. The ability of a particular ventilation system design to provide adequate ventilation during normal and emergency conditions can be evaluated using computer modeling and simulation techniques. A train fire will cause a sudden change in the tunnel ventilation pattern by adding an unsteady and fast-growing source of heat. The hot air and gasses created by a fire will tend to flow uphill, possibly against the normal flow, producing a 'backlayering effect." To prevent this effect from happening, enough ventilation must be provided and the governing criterion to establish the required airflow is called 'Critical Velocity." Several software packages are available for special applications on tunnel and station ventilation as well as to model the spread of smoke and heat in case of a major tunnel fire, using Computational Fluid Dynamics. This paper presents the current issues in subway ventilation, as shared by the public transit community around the world, together with modern alternative design concepts vis-à-vis the more stringent emerging Fire-Life Safety criteria. Examples of recent studies and ventilation systems design are provided.

Jan 1, 1997

The National Mining Hall of Fame and Museum in Leadville, CO seized the opportunity to show off during its 10th anniversary induction banquet on Sept. 6. "We wanted to make people more aware of the mining hall of fame and museum," said Carl Miller, its executive director. The annual event honors inductees into the Mining Hall of Fame. This year, the inductees included Paul Wheeler Allen, Joseph Rosenblatt, Arthur Fay Taggart, Joseph Toy, Joseph Wharton and John Benjamin Zadra (ME, August, pp. 60-63). Allen, of Pasadena, CA and Rosenblatt, of Salt Lake City, are both living. Only Allen was able to attend. This year's induction banquet was the first held in Leadville, North America's highest incorporated city, at 3,094 m (10,152 ft) above sea level. The banquet gave attendees an opportunity to see the museum in its century-old 6,500-m2 (70,000-sq ft) Victorian schoolhouse. Many of the 350 guests came in 1890s dress to the black-tie affair. The evening included a cocktail reception and an open house along with a catered, prime rib dinner. During the open house, attendees had the opportunity to tour the museum's 12 rooms of exhibits and displays. Among items of interest, it was noted that a framed directory of inductees now enhances the entrance to the hall of fame. The directory is organized by the inductees' names and the location of their plaques, allowing visitors to quickly find hall of fame members. Noted mining historian and author Duane Smith delivered the keynote address at the banquet. After the induction of the six honorees, attendees danced to the big-band era music of the Leadville 17-piece band BandAge. Karl Elers was the master ceremonies for the evening's program. He is a member of the hall of fame's board of directors and is chairman of Battle Mountain Gold Co. Allen was honored by the presence of 26 former colleagues and associates. He told the audience that he originally thought the museum should have been located in Denver. "But I have been proven wrong," he said. For many years, Allen was the operational executive of Cyprus Mines Corp. and a key participant in the company's growth. Allen received a replica of his mining hall of fame plaque from Thomas Falkie, chairman of the hall of fame's board of governors and president of Berwind Natural Resources Co.

Jan 1, 1997

The recent mine disasters in Australian coal mines have initiated an introduction of Self-Contained Self-Rescuer (SCSR) as component in the development of new escape strategies for miners. These self-contained self-rescuers are closed circuit, demand sensitive breathing apparatus that make oxygen available to the wearer for a nominal period of time. Their operation is completely independent of the surrounding atmosphere. Once properly donned, the SCSR can assist a miner to escape from an area containing smoke, toxic gases or an oxygen deficient atmosphere. The duration of a typical SCSR is usually taken at the point of complete collapse of the breathing bag which is accompanied by an increase in breathing resistance and inhaled levels of carbon dioxide. Because the oxygen consumption (V02) and the heart rate are correlated, a prediction of V02 and consequently the duration of an SCSR can be made by monitoring the heart rate. Thirty-seven volunteers participated in field simulated escape trials at four underground coal mines. The results from the field trials suggested that oxygen consumption depends on the heart rate, the body weight and exercise rating of the miner. All the volunteers were asked to fill out the questionnaires to evaluate the performance of the units. The miners indicated that they could tolerate the inhaled temperature without any difficulty to breathing resistance. A complete statistical analysis of the field results is also presented.

Jan 1, 1997

By Tom Treleaven

The widening of the Panama Canal to approximately 130 feet (40 m) for its entire length began just a few years ago. The original expansion program was slated for completion in 18 to 20 years, but has recently been reduced for completion within the next four years. This means that a tremendous amount of blasting at simultaneous points along the canal, by both the Panama Canal Commission (PCC) and many subcontractors, is necessary to achieve the new completion deadline. The accelerated program also imposed many logistical concerns, since marine trafIic is always heavy and cannot be stopped for blasting. Because some of the large and heavy cargo vessels clear the bottom of the canal by only about 6 feet ( 2 m), the blasting cannot result in any large boulders into the center of the canal, for fear of grounding and damaging a vessel, not to mention the traffic delays and lost income of approximately 1 to 2 million dollars per day.

Jan 1, 1997