Search Documents

By Trent A. Tempel

In 1989 Newmont Gold company initiated a project to develop a treatment process for higher grade refractory gold ores to be mined from deposits along the Carlin Trend in Nevada. Extensive laboratory and pilot testing have identified a unique whole ore roasting process for oxidizing these ores prior to gold recovery by conventional cyanidation techniques. Subsequent detailed engineering studies by Fluor Daniel evaluated three different dry grinding flowsheets for feed preparation to this roasting circuit. The selected flowsheet will incorporate a two compartment ball mill with an attached drying chamber that is driven by a 11.2 MW (15,000 hp) wrap-around motor.

Jan 1, 1993

Segregation roasting tests were carried out on Zaire cobalt oxide ores assaying about 2% Co and 3.5 to 6.5% Cu. The major parameters tested during the laboratory investigations were temperature, dosage and type of reducing agent, dosage and type of chloridizing agent, and particle size. Results showed that standard conditions suited to the segregation of copper ores, i.e. low temperature and low dosages of reducing and chloridizing agents, resulted in the segregation of copper only, while conditions suited to the segregation of lateritic nickel, i.e. higher temperature and increased dosages of reducing and chloridizing agents, led to a successful segregation of both copper and cobalt. Under the best conditions, 88% of the cobalt and 98% of the copper could be recovered in a concentrate assaying 32.5% Cu and 8.5% Co. Alternatives to process such a concentrate are briefly reviewed.

Jan 1, 1993

By R. Tremblay, M. Burrows

"In the summer of 1990, pilot scale testing of a Jameson cell was carried out at Falcon bridge Limited, Kidd Creek Division. The Jameson cell is self aspirating and has fewer mechanical parts, thus it has a lower operating cost compared to conventional cells. This lower operating cost combined with positive pilot scale results, justified the evaluation of two full scale cells in the plant. The plant test had two mandates:1. Gain a thorough understanding of the cells operation and design constraints.2. Develop a flow sheet to replace three divisions of copper cleaner flotation.This paper provides an overview on the installation, commissioning and evaluation of the two Jameson cells acquired. The current status of the test program is also discussed.IntroductionThe Falcon bridge Limited-Kidd Creek Division concentrator is located in Timmins, Ontario. The concentrator, commissioned in 1966 and expanded in 1978, consists of four parallel grinding and flotation divisions utilising small cell (60 ft3) technology. With increasing pressure to maintain low operating unit costs a series of studies were undertaken to assess the impact of new technologies in the flotation circuits. The goals of the project were to improve productivity through increased metallurgical performance and/or reduced operating costs.One of the technologies investigated was the Jameson cell designed by Dr. Graeme Jameson of the University of Newcastle and marketed by MIM Holdings Limited, Australia. This style of column technology was chosen based on its potential for reduced capital and operating cost versus large conventional cells.The success of pilot testwork in 1990 led to the installation of two production sized Jameson cells beginning in October 1991. The units were to be used to confirm pilot results and determine equipment requirements for flotation modernisation. This paper will discuss the results and experiences Kidd Creek has had with the Jameson cell from pilot scale through installation and commissioning of the plant units."

Jan 1, 1993

By David R. Wilburn

The U.S. Bureau of Mines investigated the resources, costs, capacities, market relationships, and short-and long-term supply of bauxite, alumina, and aluminum. The 45 evaluated mines and deposits in 14 market economy countries (MEC's) have a demonstrated resource of 8.4 billion mt of bauxite and an aluminum content of approximately 2.1 billion mt. Developed world bauxite resources and existing primary aluminum smelting and refining capacity are sufficient to satisfy demand through at least 1995, when additional properties (with higher cost levels) would need to be developed to satisfy future demand levels. It is anticipated that new alumina or aluminum production most likely would occur in developing regions with large bauxite potential, low-cost energy sources, and a close proximity to refining and/or smelting capacity. An increase in aluminum recycling capacity would help meet future demand increases. A series of network model supply analyses was performed for the period 1988 through 2000. Based on announced future production levels and assuming demand grows at the level outlined in the analyses, model results indicate there is sufficient material available to meet demand until 1998, where-upon an aluminum shortfall is projected. Additional analyses investigated the effect of a reduced growth rate of demand and regional production variations in Venezuela on the international aluminum industry.

Jan 1, 1993

By Christopher J. Bise

Volume II of this collection of research reports, entitled "Model Training Program," provides the framework and details for developing a tailored training program for a specific mine based upon documented human-performance deficiencies. To do this, several steps must be followed prior to program implementation: 1) background information must be gathered (database analysis), 2) direct observation of indicated problem areas should be conducted (safety sampling), and 3) separation of those deficiencies to be addressed through training from those which would be better addressed by workplace or equipment redesign (trainability assessment). Once training is determined to be the appropriate strategy for addressing the noted deficiencies, several approaches can be taken, depending upon whether the problem is related to repetitive work procedures in a predictable, a variable, or a dynamic workplace with a substantial amount of interaction between workers, equipment, and the environment. Although this volume and the subsequent seven volumes provide examples of how the training information was field tested using various strategies (for example, loss control, task training, etc.) and techniques (for example, microcomputer-based exercises, lectures, etc.), the ultimate selection of the delivery method is based on cost/benefit analysis. Therefore, the Model Training Program has incorporated a Training Cost Model as a desirable component.

Jan 1, 1993

By Alan R. Buehler

The Bureau of Mines conducted a mineral investigation of the 177,000-acre Secesh study area; most of the area had been proposed as wilderness. Bureau personnel mapped and sampled several hundred mine and prospect workings; 1,715 rock, soil, and placer samples were taken during the investigation. The study area is centered about 25 mi east-northeast of McCall, Idaho, in the Payette National Forest. Five mining districts extend into or are adjacent to the study area. There have been more than 3,000 mining claims located inside the study area, 884 are current. In excess of $17 million (historical value) in placer and lode gold has reportedly been produced from the Warren district alone. The study area contains gold, silver, copper, lead, zinc, tungsten, and antimony. At least six properties that would be in the proposed wilderness contain gold resources; more than 18 million tons averaging 0.038 oz/ton gold have been identified. Additional resources may be located at 4 other localities. The 4th of July mine is currently producing gold/silver/lead ore. Similar resources may be located on at least 3 other properties. Placer samples from the study area contained up to 0.34 oz gold/yd3 ($120/yd3). The samples are representative of relatively small occurrences and do not constitute resources; small quantities of gold may be recovered by recreational placer miners.

Jan 1, 1993

Jan 1, 1993

"The Dome Mine, located in South Porcupine Ont. has been in operation since 1910 and is owned and operated by Placer Dome Inc. The current milling facilities were constructed in two phases with the first being commissioned in 1982. It consists of a grinding, gravity separation, thickening, and leaching circuits. The second phase was commissioned in 1988 with the addition of the CIP, stripping, electrowinning, and carbon regeneration circuits.It is now common practice in the gold processing community to add liquid oxygen to leach circuits to increase both recovery and kinetics. Along with these benefits the metallurgical group at the Dome realized the potential to replace compressed air with liquid oxygen as a source of oxygen for the dissolution of gold. A plant trial of liquid oxygen was undertaken during the fall of 1991. The results of this first test were favourable enough to warrant further investigation, and a second plant trial was conducted in December 1991.The data generated as a result of each trial revealed that oxygen could be economically substituted for compressed air as a source of dissolved 02. The energy savings in required horsepower enabled a rapid payback period. Thus the project was approved in the spring of 1992 and l should be operational during the final quarter of 1992. INTRODUCTIONIn a continuing effort to reduce operating costs and improve recovery at the Dome mill it was decided to investigate the feasibility of adding liquid oxygen (02) to the leach circuit. It is now common practice in the gold processing community to add 02 to the leaching process to increase both kinetics and recovery. It was anticipated that an increase in kinetics would allow us to eliminate one or more leach tanks while maintaining acceptable recoveries. The metallurgical group felt that along with these benefits, the potential was also there to reduce power consumption through the reduction in the processing of compressed air which is quite costly (12 cents/1000 cubic feet per minute in 1991)."

Jan 1, 1993

By P. N. Eksteen, G. E. Greig

The South African mining industry currently installs about 6 km per month of plastic pipes for conveying compressed air and water. Plastic pipes have a number of desirable properties and are favoured by many mining engineers because of their low mass, which facilitates ease of erection and assembly, and their excellent corrosion resistance and durability. However, they are combustible, and if involved in an underground fire can contribute to the overall toxicity of the combustion gases emitted. Furthermore, plastic pipes have the potential to conduct a fire from one part of a mine to another, and, by so doing, exacerbate an already hazardous situation. The limitations of small scale tests and the need to establish a large facility where underground conditions could be simulated was recognized by the South African mining industry. This paper briefly describes the Industry's full scale fire test facility and presents the conclusions drawn as a result of a number of full scale combustibility tests conducted on pipes manufactured from unplasticized Poly Vinyl Chloride (uPVC) and High Density Polyethylene (HDPE). Based on these findings, some practical solutions to prevent the spread of fire along the length of pipe columns of various pipe diameters and suspension configurations are presented. Recently some new and exciting developments in the field of intumescent coatings have occurred which are proving effective in minimizing the incidence of fire underground on South African mines. The potential benefits of these coatings are briefly discussed. INTRODUCTION Plastic pipes used underground on mines are predominantly in the form of protective cladding on insulated chilled water pipes and as service pipes for the conveying of water and compressed air to the workings. Plastic pipes have found wide use in the aggressive environmental conditions encountered underground due to their favourable properties relative to steel; these include being lightweight, easily installed and virtually immune to corrosion. However, plastic pipes are inherently combustible and can contribute to the overall hazard in three ways: (i) they are easily ignitable and can provide the initial fuel for a fire. (ii) once ignited, they can propagate a fire along their length and by so doing ignite other combustibles in their path, thereby contributing significantly to the overall conflagration. (iii) they can contribute to the overall heat, smoke and toxic gas emissions from a fire. While conscious of the value of small scale fire tests, the South African mining industry recognized the need for full scale testing to determine the combustion characteristics of plastic pipes under conditions closely approximating those underground and, as a consequence, a full scale fire tunnel test facility was commissioned with the objective of being able to (a), accurately evaluate the potential hazard of the various types of the plastic pipes found in mines, (b) use this information to suggest suitable fire engineering practices to minimize the hazard and (c), to practically verify the efficacy of the practices suggested. THE FIRE TUNNEL The fire tunnel is situated on a mine in the Western Transvaal and is 40 m long with a cross section of 3 m x 3 m which is typical of many haulages currently in use in South African gold mines. The ventilation drawn through the tunnel is provided by a 110 kW centrifugal exhaust fan and air velocities can be varied from 0 to a maximum of 5,8 m/s.

Jan 1, 1993

By Jack Parker

Critical width Before we go further into pillar design, we should look into the matter of "critical width," because of its effect on pillar behavior. Critical width refers to the greatest width that the rocks above the mine can span before failure or, if there are pillars, the width to which we must mine before the pillars accept the full weight of the overlying materials. There are theories to help calculate that probable width, and they usually boil down to one-quarter or one-third of the depth of cover; but they don't always fit, and it would be better for us to understand the factors that control local conditions. Critical width may be controlled by the thickness or strength of one or more of the strata above the mining horizon. In a gold mine, we might have a thick granite or basalt above us, perhaps capable of bridging across most or even all of a small ore body. In that case, pillars might have to support nothing, or perhaps just the weaker or damaged rock below the strong main roof. Obviously it would be wrong to design for tributary load on pillars based on some lab-determined rock strength. In some coal mining districts in Utah, huge steps can be seen in the mountain sides, with slopes on weathered shales and vertical cliffs 100 or 200 ft high in thick, hard sandstones. The sandstones are capable of bridging across hundreds of feet, often making mining deceptively easy at first, but it becomes more difficult as greater areas are opened. Sometimes such a mining sequence leads to violent bumps and bursts as the wide spans of sandstone sag and bear down on the working faces, like giant nutcrackers, or as bridges eventually fail, releasing much pent-up energy.

Jan 1, 1993

By C. J. Bise

One area of study for the Coal Mine Injury Analysis project was to illustrate how loss control can be used as a foundation for mine safety training. After an initial review of the principles of loss control, the instruments often used for worker/worksite appraisal, such as incident reporting, analysis, and investigation, workplace observation, worksite inspection, and safety audits and checklists were evaluated for their effectiveness. The findings were then applied to the continuous-miner worksite at several mines to modify the techniques for use in a highly dynamic man/machine work environment. Before the information gathered from the review of the various continuous-miner worksites was presented at the annual retraining sessions at five mines, a trainability analysis procedure was developed to separate training shortcomings from those problems resulting from improper equipment design or unsatisfactory working environments. Also, several microcomputer-based training programs were developed to aid in conveying the loss-control concepts to the trainees. Finally, the results from the implementation and evaluation of the loss-control-based training programs were documented, including the complete training script for one of the case-study mines. The procedures outlined in this study will aid mine training specialists in developing focused, pro-active accident-prevention strategies and training programs that are based on sound loss-control principles.

Jan 1, 1993

By Kerry Spickelmier

A traveler driving across desolate central Nevada to the Round Mountain property can easily identify with turn- of-the-century prospectors seeking a fortune, or at least an existence, from the high desert. But now a shadow passing overhead is as likely a sophisticated fighter aircraft from Stillwater Naval Air Station as a circling bird, and the famous trails west show only as historical markers along the highway. Even the approximately 400- km (250-mile) trip southeast from Reno or northwest from Las Vegas takes hours now, not days. And the camps of Round Mountain’s early prospectors have been replaced by one of the world’s largest gold heap-leaching operations. While Round Mountain’s uniqueness begins with its scale, it doesn’t end there. Consider the mine’s low cutoff grade of 0.2 g/t (0.006 oz/st) gold, made possible by a new dedicated (not reusable) leach pad. Also, the operation’s degree of automation means that ore dropped in the south crusher system is not manually handled until it is stripped from the pads. There is the bonus of a geothermal field that is tapped to heat the leach solutions in the winter. And, of course, there was that “unexpected” hitch expected in all mining operations. For Round Mountain, it meant buying a gravity plant to process the gold nuggets discovered last summer in a fault gouge.

Jan 1, 1993

By Ruoming Gong, Arindam Samanta, Ragula Bhaskar

Three studies conducted at the University of Utah relating to the effect of scrubbers on face airflow patterns, the resulting dust exposure of operators and the development of a throat scrubber for continuous miners are summarized in this paper. The first study involved full-scale laboratory tests to determine the potential dispersion patterns and transport of dust at a continuous miner face, using different ventilation configurations and a scrubber. Concentration maps were developed and potential exposures at operator positions were examined. The second study involved the development of a 3-D numerical model to predict airflow patterns generated by a scrubber at a continuous miner face. The model was designed to evaluate the role of various face parameters on airflow patterns at a miner face and to complement the full-scale testing. The third study involved the design and fabrication of a low profile hydraulically powered continuous miner throat scrubber. The scrubber uses three hydraulic motors and small diameter fans to draw about 3000 cfm (1.42 m3/s) of air and uses a flooded bed scrubber to filter dust particles.

Jan 1, 1993

By Henry A. Russell

During the last ten years Parsons Brinckerhoff has become a leader in the area of tunnel rehabilitation. A significant part of any tunnel rehabilitation program is the control of groundwater infiltration into the structure. This leakage over time, causes deterioration of the structures, and creates numerous operational problems for the tunnel operator. This paper will address current procedures for identification, documentation, and recommendations of repair methods for the control of groundwater infiltration in rail and highway tunnels.

Jan 1, 1993

By J. A. Brierley, C. L. Brierley, K. A. Prisbrey, R. W. Bartlett, J. G. Harrington

Bacterial oxidation of gold-encapsulating sulfide minerals in low-grade refractory ores was investigated over a period of one year. Crushed ore samples were held in wet, bacteria-inoculated, aerated columns. Sulfide mineral oxidation data were correlated with subsequent gold cyanide extractabilities. Experimental results for both sulfide conversion and gold extraction were compared with a biooxidation kinetics model that incorporates rock size, mineral grain size, and heterogeneous pyrite reaction kinetics. Using the model, extrapolations were made over three years for biooxidation of ore in large stockpiles. Ferric ion (oxidant) diffusion in the solution-filled pores of the rock matrix does not control the biooxidation kinetics of ore crushed to -25 mm.

Jan 1, 1993

This paper examines the issues involved in the technical audit and valuation of exploration prospects. Certain methodologies are more appropriate to use depending upon whether the mineral property valuation is of an exploration area, a project under development, or an operating mine. Valuation approaches that are reviewed include the Multiple of Exploration Expenditure, Joint Venture Terms, Rules of Thumb, and particularly the Kilburn Rating Method. The DCF/NPV Financial Simulation Method, even modified by the use of Expected Values, is not considered appropriate for valuing exploration prospects. The choice of the most appropriate methodology and its successful application depends primarily upon the amount of reliable input data available and, more importantly, the experience and judgement of the valuer. It must be remembered that all valuations are time and circumstance specific and will be generally subject to revision as more data becomes available.

Jan 1, 1993

By Debra C. Man, S. Thomas Freeman, F. Wiley Horne

INTRODUCTION The Metropolitan Water District of Southern California (Metropolitan) is the largest water wholesaler in southern California. Its service area spans the major urbanized portions of Ventura, Los Angeles, Orange, San Bernardino, Riverside and San Diego counties. More than 15 million people are serviced by Metropolitan through its 27 member agencies. The primary sources of Metropolitan's water supply are the Colorado River Aqueduct (CRA) and California's State Water Project (SWP). Currently, planning and design level studies are underway by Metropolitan to expand the water storage and conveyance systems within the service area for the purposes of providing increased efficiency and flexibility to manage limited water supplies, improving water quality, and increasing system reliability. The system reliability issue is particularly significant because the conveyance facilities from both the CRA and the SWP must cross the active San Andreas fault. This fault is considered to be the source fault for the anticipated "Big Earthquake" in southern California. To meet these objectives, Metropolitan's expansion plans involve a major new storage reservoir, new large diameter pipeline and tunnel conveyance facilities, more efficient utilization of existing groundwater basins, and an aggressive public awareness and conservation program. This paper focuses on the planning studies that have been carried out for over 50 miles of tunnels being considered for several of Metropolitan's proposed conveyance systems. These tunnels have ranged in length from a few hundred feet to over 42,000 feet, with depths of cover ranging from a few tens of feet to over 3,000 feet, and finished diameters ranging from 10 to 20 feet.

Jan 1, 1993

By Jan K. Wolski

Detection of the air recirculation branches within a large ventilation network may be difficult, therefore a PC computer routine has been developed to perform this task in an efficient and reliable manner. This paper describes the method illustrated using a network with complex multi-recirculation circuits. The fact that only the air flow directions and not the flow rates are used in calculations is of some interest. The air recirculation during a real mine fire is demonstrated using the PCVENT program, whose version 4.0 includes current information about any recirculation branches during network calculations or during a fire simulation. This paper also discusses some transient problems related to air recirculation, and gives examples.

Jan 1, 1993

By K. L. Wiley

In-situ leaching, initiated in 1986 at San manual, was economically developed in 1989. The primary reason for this lag time between startup and viable production was the time required for technical development. The technical development pursued comprised detailed design, development, and implementation of in-situ well construction methods, formulation of suitable well pattern arrays, and the development of extensive hydrogeologic and geochemical knowledge of the mineral deposit. Since 1989, the in-situ leaching program has become a viable and cost effective method to extract copper from the supergene mineralized zone of the San Manuel deposit. The in-situ leaching methods that are currently utilized have been progressively expanded and continually developed and will became the cornerstone of copper production from the San Manuel oxide mineral deposit. This paper presents an overview of the supergene hydrogeology, current design techniques, drilling methods and well completion, pump determination and setting, solution management, and future plans for the increased extraction of copper by in-situ leaching methods at the San Manuel mine.

Jan 1, 1993

By Seth L. Pearlman

A major excavation support case history for the Eastern approach to the Third Harbor Tunnel (THT) in Boston, MA is described, which uses an anchored Soil Mixed Wall (SMW). Both general and project specific information is provided regarding the design and construction of SMW walls. In addition, conclusions are presented that discuss the suitability of this particular application and other possible variations.

Jan 1, 1993