Search Documents

By David T. Bunney

In .December of 1987, International Mill Service, Inc. signed an exclusive licensing agreement with Tetronics Research & Development Co. Limited of Faringdon, Oxfordshire., England to commercialize plasma technology which had been demonstrated in an EAF dust processing application. The intent of the process is to reduce and volatize the zinc, lead and cadmium oxides inherent in EAF dust and collect these elements as metals in an ISP (Imperial Smelting Process) zinc splash condenser, and to render the resultant slag an inert, non-hazardous material. With these objectives in mind, IMS started commissioning facilities in 1989 at Florida Steel in Jackson, Tennessee and Nucor-Yamato Steel in Armorel, Arkansas. This paper will address the commercial development and progress of the technology at these two installations. Process Description In the EAF steelmaking process typically the off gas stream is cleaned by some form of baghouse. The particulate collected is known as Electric Arc Furnace dust and has been designated by the U.S. EPA as hazardous waste number K061, once it leaves the collection system. This designation was given to the material due to the high toxic concentrations of lead and cadmium (nickel and chromium for stainless EAF dusts) inherent in the dust. IMS' method of operation is to locate the facilities on the client mill's property adjacent to the baghouse. The dust is transported directly to IMS via a closed conveyance system. This method enables the technology to be an additional processing step in the steelmaking process. Once the dust has been transported to the IMS facility, it is fed, metered and mixed mechanically in the feed conveyance system with a carbon reductant (typically coke breeze). The carbon reductant is approximately 10% of the dust feed rate. This mixture passes through the feed system and enters the furnace

Jan 1, 1992

By Stein Tore Johansen

Some ferro-silicon fumaces have heat-recovery equipment. Here, the recovery of electric energy from the off-gases can be increased by increasing the off-gas temperature. This is easily done by reducing the amount of air which usually is mixed into the off-gas to cool the gas mixture. If the off-gas becomes too hot problems with severe fouling or clogging of the gas channels? close to the fumace is observed~ The result is irregular stops to clean the off-gas channels. The paper focuses on the nature? of the clogging phenomena and some of the ways to avoid clogging. A detailed experimental study was carried out at the Elkem Thamshavn Plant. Theoretical studies were performed to understand the particle deposition, turbulent multiphase fluid flow and off gas combustion in the off-gas channels. The study has resulted in reduced clogging.

Jan 1, 1992

By Dan Mancuso

This case study is an example of how Encyle/Texas, Inc. (a subsidiary of ASARCO) responded to various socio-economic forces by converting an idle zinc hydrometallurgical refinery into a metals recycling facility. The facility accepts metal-laden process waste streams and produces various "synthetic ores" which are sold back to industry. Acceptance and reactions by industrial, political, economical and regulatory interests towards the project are also discussed.

Jan 1, 1992

By T. M. Ruff

A prototype mucking machine designed to operate in narrow-vein stopes was developed by Foster- Miller, Inc., Waltham, MA, under contract with the U.S. Bureau of Mines. The machine, called a compact loader-trammer, or minimucker, was designed to replace slusher muckers in narrow-vein underground mines. The minimucker is a six-wheel-drive, skid-steered, load-haul-dump (LHD) machine that loads muck at the front with a novel slide-bucket system and ejects it out the rear so that the machine does not have to be turned around. To correct deficiencies of the tether-remote-control system, a computer-based, radio-remote-control system was retrofitted to the minimucker. Initial tests indicated a need to assist the operator in guiding the machine in narrow stopes. An automatic guidance system that used ultrasonic ranging sensors and a wall-following algorithm was installed. Additional tests in a simulated test stope showed that these changes improved the operation of the minimucker. The design and functions of the minimucker and its computer-based, remote-control system are reviewed, and an ultrasonic-sensor-based guidance system is described.

Jan 1, 1992

By Doss H. White

Alabama's non fuel mineral industry produced $560.6 million of mineral commodities in 1990. This was an increase of $99 million over the 1989 value and a new State record, a record achieved despite the slowdown in the national economy. This was the first year that Alabama's mineral value exceeded one-half of 1 billion dollars. The value of stone and cement, the two leading mineral commodities in terms of sales, increased $71 million over that reported for 1989 and was the primary reason for the new mineral value record. The State ranked 21st among the 50 States in total mineral value and contributed 1.68% of the total U.S. mineral value of $33.3 billion.

Jan 1, 1992

By John R. McDonnell

The Valle Vidal Unit comprises 100,000 acres In Taos and Colfax: Counties, New Mexico. The unit was donated to the American public In 1982 by the Pennzoll Co. and is administered by the U.S. Department of Agriculture Forest Service as an addition to the Carson National Forest. During 1990-1991, the Bureau of Mines conducted a mineral Investigation of the unit as authorized by an Interagency Agreement (1987) Intended to assist the Forest Service to incorporate mineral resource data In forest plans. The Bureau reviewed literature and records concerning mineral resources and mining activity, and performed a field examination of mines, prospects, and mineral occurrences in and near the Valle Vidal Unit. The La Belle mining district encompasses most of the western part of the Valle Vidal Unit. The district was most active between 1893 and 1902, after the land grant was opened to prospecting and gold discoveries were reported. The discoveries were low grade, and eventually were abandoned. The Bureau's appraisal of the district determined that lode gold occurs primarily in fissure veins in volcanic rocks, and placer gold occurs In weakly cemented sedimentary rocks and alluvial sediments; but at a grade that is currently considered subeconomic. If the price of gold increases in the future, prospecting and exploration in the area may be renewed, but the activity would likely be limited due to "acquired land status" restrictions, which require mineral leasing and prohibit claim location in the Valle Vidal Unit.

Jan 1, 1992

The STATE MINERAL SUMMARIES publication provides estimated data and summaries of mineral activities at the State level for 1991. Most of the estimates are based on nine months data. Individual State summaries are published separately as State Mineral Industry Surveys and copies can be obtained from the appropriate State mineral officer or Bureau field office specified in each State summary.

Jan 1, 1992

By T. Leftwich, G. Faison, K. Pavlich, R. Borden, S. Pavlou

Recent regulatory and policy initiatives under the Resource Conservation and Recovery Act (RCRA), and the Comprehensive Environmental Response Compensation and Liability Act (CERCLA), will have a significant effect in risk reduction requirements for the mining and minerals processing industry. For example, Congress is considering regulating 20 special wastes from the processing of ore and minerals through RCRA Subtitle D and TSCA. The performance of risk analyses and environmental planning at mining projects is often driven by Federal and state regulatory standards. Recent regulatory and policy initiatives by the Environmental Protection Agency under the Resource Conservation and Recovery Act (RCRA), and the Comprehensive Environmental Response Compensation and Liability Act (CERCLA), will have a significant effect on environmental planning and risk reduction programs for mining and minerals processing. Regulatory programs implemented under other Federal laws including the Safe Drinking Water Act, Clean Water Act, and Clean Air Act will also impact industry practices. This paper provides: 1) a brief overview of mining waste and mining waste management, and 2) a description of these regulatory initiatives and a discussion on the impacts of new requirements on environmental and risk reduction programs in the mining industry.

Jan 1, 1992

By Williams P. A

Tailings dams constructed by the upstream method have traditionally been built using the sand fraction of the tailings, which has automatically provided a relatively permeable embankment material, and helped provide the necessary drainage conditions which are a pre-requisite for safe and stable dam construction using this method. This paper discusses some recent trends which have resulted in proposals to use impermeable material in place of the sand fraction as the embankment material, both for the starter dam, and subsequent lifts. The consequences of these types of decisions on the overall stability of the dam are illustrated, and the need for continued monitoring of pore pressures in the tailings as the dam is raised is emphasised.

Jan 1, 1992

By A. A. Trickett

In the treatment of gases from pyrometallurgical processes prior to acid manufacture, volatile components, sulphur trioxide and particulates ,are removed in wet gas cleantng systems. In the process a weak acid stream is generated, typically less than 10% H2S04, contaminated with volatiles such as arsenic, fluoride and chloride', plus metallic particulates. This effluent stream has, in the past, been disposed of in a variety of different ways. As a result of changing environmental legislation, smelters are having to review alternative solutions for treating this effluent stream. This paper' will describe a process developed by Chemetics which treats this effluent stream, generating a small dry metal sulphate stream plus a clean acid stream which is suitable for recycling to the smelter acid plant.

Jan 1, 1992

By Ferri P. Hassani, Riadh Bouzaïene

"Selected methods of pressure loss predictions in horizontal slurry flow in pipelines are presented. For a given combination of flow velocity, solids concentration and particle size, the slurry and its flow conditions are described, and an appropriate method of pressure loss prediction is outlined. The wide range of conditions treated in this paper may be found in practice in areas varying from the hydraulic transport of low concentration slurries to dense-phase conveying of paste backfill in underground mines.IntroductionThe hydraulic conveying of solid particles in pipelines is a major component of the mining and mineral processing industry. Whether the objective is to transport ore to the processing plant or to make use of mill tailing as backfill material; the need for well designed, economical hydraulic conveying systems is recognized.The contribution of this paper is part of an on-going research program at McGill University involved in optimizing and developing techniques for total mine waste disposal. One of the main concerns in the conveying of solid-liquid mixtures is the prior knowledge of the pumping power input required. This energy requirement is directly proportional to the pressure losses incurred in the pipeline system. Understanding the sources of such pressure losses and predicting their magnitudes should enable the system designer to make informed decisions regarding the optimum mode of hydraulic transportation commensurate with the over-all requirements of the operation.This paper is an attempt to classify pressure loss prediction methods encountered in the literature for solid-liquid mixtures. In spite of the large number of publications spanning thirty years of research in the field of slurry transportation, it is sometimes difficult to correctly identify the appropriate methods applicable to a given situation. This is partly due to the inherent complexity of the mechanics of slurry flow and the ensuing uncertainty about the nature of the flow regime under investigation.Our approach is to use three fundamental parameters, namely: flow velocity, solids concentration and particle size (for solid particles with a given density) to characterize the slurry and the flow conditions, and to match them with an adequate pressure loss prediction method. For each combination of flow velocity, solids concentration and particle size, a description of the most likely prevalent flow conditions and some known methods of dealing with them will be presented. Qualitative definitions of ""high"" and ""low"" magnitudes of the aforementioned parameters will be given as a general guide to the classification scheme presented in this paper."

Jan 1, 1992

By A G. Mitchell

Stream sediment geochemical analyses were collated from open-file mining company reports and assembled in the REGCHEM computerised database at the Institute of Geological and Nuclear Sciences Limited. The database operates on an IBM-compatible PC microcomputer using an application programmed in dBASE IV and termed GEOEXPL. By August 1992, data for 6383 stream sediment samples from 6335 different sites in the Coromandel Peninsula region (Hauraki Goldfield) were entered, giving a total of 29 292 separate elemental analyses. Preliminary statistical analysis using PROBPLOT on a set of data collected by AMOCO from the Mahakirau-Whangapoua area shows that these data are a complex mix of subpopulations related to mineralisation and different source rock types. Thresholds of 37 ppm copper, 31 ppm lead, 112 ppm zinc, and 2.3 ppm molybdenum, defmed by arithmetic models for the combined data set, separate the individual element sets into 'first order anomalous/lesser anomalous and background' subpopulations as follows: copper five per cent/95 per cent, lead five per cent/95 per cent, zinc one per cent/99 per cent, and molybdenum 15 per cent/85 per cent.

Jan 1, 1992

By J. W. Dini

Introduction The mission of the Materials Fabrication Division (MFD) is to provide fabrication services and technology in support of all programs at Lawrence Livermore National Laboratory (LLNL). MFD involvement is called for when fabrication activity requires levels of expertise, technology, equipment, process development, hazardous processes, security, or scheduling that is typically not commercially available. Customers are encouraged to utilize private industry for fabrication activity requiring routine processing or for production applications. MFD is .a large diversified service organization including approximately 400 full time employees. The group provides a wide variety of processes including all common machining and fabrications operations, laser and water jet cutting, electrical discharge machining, lapping, electron beam and laser welding, vacuum brazing, heat treating, forming, electroplating and metal finishing, optical polishing and grinding, vacuum coating, vacuum engineering and a variety of plastics operations. These operations occupy more than 1,250,000 square feet of floor space. For more detail on the many fabrication related services available from MFD, see Reference 1.

Jan 1, 1992

By Art Johnston

Gas handling at Magma Copper company's, San Manuel smelter receives process gas from a flash .smelting furnace and four copper converters. The major gas handling equip11lent consists of four electrostatic precipitators and a sulfuric acid plant. Process ,vessels in gas handling are, typically confined, spaces. Lethal gases, mechanical and chemical hazards, and the difficulty of rescue, should an accident occur, makes this area a must in the safety plan. The presence': of hazardous chemicals and explosive gases in process' vessels and piping are of major concern when repairs' are required. Proper job procedures are critical to prevent injury during repairs. This includes plant employees and contractors who are likely to be unfamiliar with the hazards ,involved. The safe operation of a gas handling operation must include the functions of operations employees on a daily basis. This includes a safe working environment and involvement of all employees in the safety program. If an injury does occur quick medical response is critical to prevent serious injury. Medical responders must be adequately trained and prepared to treat the injured person without becoming victims' themselves. The methods used at Magma Copper Company to deal with these safety problems are the focus of this presentation.

Jan 1, 1992

By Colwell J. B, Constantine A. E

A unique, regional grid of deep (12 - 14 second record length), seismic reflection and refraction data has been recorded by the Australian Bureau of Mineral Resources (BMR) across the offshore Gippsland Basin and parts of the adjacent Bass Basin, in southeastern Australia. These data have been combined with onshore mapping to produce a new model for the development of the Gippsland and adjacent Bass Strait basins. Overall, the Gippsland Basin contains up to 12 - 14 km of sediment in an ESE-trending depocentre bounded on its north and northwestern margins by a detachment ramp, and on its southern side by a relatively linear, listric fault system. The basin, together with the adjacent Bass and Otway Basins, appears to have formed as part of a linked, largely- strike-slip to 'transtensional' system, which started to extend through Bass Strait, probably during the latest Jurassic. Each of the basins developed by movement on a common detachment or detachment complex, which produced headwall extension at their western ends, in the areas now occupied by the Strzelecki Ranges, Otway Ranges - Torquay Sub-basin, and Robe Trough. Adjustments and reactivation from the mid Cretaceous of several postulated microplates in the region, largely in response to Tasman Basin rifting, gave rise to the wrench-related and compressional structures which form the major petroleum targets in the Gippsland Basin. However, the same process formed largely extensional stuctures in the Bass Basin. Our interpretation of the tectonic history of the Gippsland Basin leads us to the conclusion that there may have been several phases of petroleum generation and migration, and that potential petroleum traps appear to exist in the deeper section, in structures sometimes not reflected at the top or near-top Latrobe Group levels.

Jan 1, 1992

By John E. Litz

Metal-bearing flue dusts are produced by some ferrous and non-ferrous industries. Many dusts are being or can be treated for recovery of metal values. Operating and proposed flowsheets for the most common dusts are reviewed. Advantages, disadvantages, product marketability, and cost implications are discussed for each flowsheet.

Jan 1, 1992

By Christopher R. Casias

A basic methodology is presented (employing both standard and theoretical assessment, analysis. and data interpretation techniques) for classifying waste containing trace levels of radionuclldes. Despite increased regulatory requirements for handling. transporting. and disposing of such waste: (I) no formal characterization methodology has yet been Implemented. and (2) no limits have been set to define the point at which a waste material is considered to be low-level and below which it Is "below regulatory concern" (BRC) or can be considered to contain no more than a diminimus level of radioactivity (i.e . is nonradioactive). 'I1le concept of diminimus limits specific to waste streams and waste forms is introduced. and a mechanism fur evaluating waste In relation to BRC and diminimus limits is outlined. This methodology can be used to perform a complete and adequate characterization of waste for classification according to its level of radioactivity.

Jan 1, 1992

By T. N. Moore, E. M. De Souza

Vibratory hand-tools can produce Hand Arm Vibration (HAV) Syndrome in their operators. This disease, often called Vibration White Finger, can cause varying levels of hand-arm discomfort and, in severe cases, impairment. In addition to the human suffering, there are also significant economic repercussions for industry. These include reduced operator efficiency, lost time through increased absenteeism and increasing compensation awards. In the mining industry, jackleg rock drills are a particularly troublesome source of hand vibration exposure. As a result, a significant amount of work has focused on redesigning rock drill handles to minimize hand-transmitted vibration. This paper details the results of a study undertaken to determine the effectiveness of using elastomer covered ("cushioned") handles in place of the standard steel design. The results indicate that, for a particular cushioned design, the overall acceleration level experienced at the hand-handle interface can be reduced by as much as a factor of three, relative to the steel handle. It is also shown that this reduction takes place predominantly in the frequency range above 500 Hz, with performance improving with increasing frequency. Qualitative evaluation of the cushioned handles by the drill operator indicates a significant increase in comfort over the standard steel handle.

Jan 1, 1992

By Y. Maeda

Non-ferrous smelting furnaces generally lnstal1 a gas cooling system for treatment of waste gas containing S02. From the point of view of corrosion resistance and recovery of waste heat, the high pressure boiler system Is the best way to cool gas, however this system requires high Initial investment and relatively higher operating costs. Because the feasibility of this boiler system greatly depends on the smelting process and scale, other lower temperature systems, e.g. water-cooled Jacket system, are more suitable If the smelting process does not produce enough steam nor generate enough electricity to compensate operating cost. In addition, the water-cooled Jacket system Is simple in structure and easy to operate. For those reasons, it is applied widely. A new smelting furnace. was planned tin our factory and It was necessary to install waste gas cooling equipment. In our case, a water-cooled Jacket system was mo11e feasible because of the low gas volume and high dust content. H was also expected to operate without maintenance for ten years. On the other hand, some leakage problems with the water-cool1ed Jacket had been experienced In the past. That is because S02 in the waste gas changed into sulfuric acid which corroded the Jacket material, As the first step, several data from actual usage were reviewed to throw light on the corrosion process, and an appropriate procedure to determine the operating temperature of cooling water was obtained. For the basis of this study, a water-cooled Jacket system was newly designed and tested for three months in a pilot plant. After this system's performance was confirmed, It was installed In a new furnace as a commercial pl.ant. After one year of operation, the initial thickness of carbon steel Jacket remains almost the same.

Jan 1, 1992

By Beardsmore G. R

Geothermal gradients in the Gippsland Basin commonly exceed 35¦ C/km. Consequently models of thermal maturation may indicate exploration targets with an anomalous age/depth distribution. However regional geothermal models are constrained primarily by observations of surface heat flow. High geothermal gradients may simply reflect the presence of low conductivity coal beds within the basin. Heat flow data are not readily available for the Gippsland Basin. Normally special purpose drill holes are required to provide direct determinations of surface heat flow. These provide core samples for thermal conductivity and allow measurements of a stable geothermal gradient at least one year after drilling. Different indirect procedures are now required to provide estimates for the Gippsland Basin. Bottom hole temperatures can be used with suitable corrections to provide an indication of the regional geothermal gradient. However the corresponding thermal conductivities are more difficult to determine. Geophysical logs can be used to detect the major lithologies but detailed statistical analysis is required for numerical estimates. Complex mixing models are now suggested for geothermal surveys linking physical properties to variations in the mineralogy of each well. Allowing for low conductivity coal measures the data in the Gippsland Basin suggest values for heat flow consistent with regional trends in Australia. Interpretation is complicated by overprinting of transient thermal events with different time scales. Apart from the tectonics of basin evolution geothermal signatures may be complicated by regional ground water migration, the 'hot spot' trace associated with southward younging of Cainozoic volcanism, diagenesis, and basin refraction.

Jan 1, 1992