Search Documents

By Guo Junfeng

The strength of coal mass saturated with gas is an essential parameter in studying the mechanism of gas and coal outburst, and its prediction method. Up to now, there has not been a method for determining the strength of coal mass saturated with gas. This paper describes a new method whereby the strength of in-situ coal mass can be determined and stored continuously and automatically. The simulation results obtained in the laboratory indicate that the new method allows a fast, reliable, inexpensive and convenient determination of the strength of coal mass.

Jan 1, 1992

The amount of hydrophobic materials constituting the mineral froth strongly influences the froth viscosity. Higher froth viscosity on the other hand can retard the drainage of physically carried over hydrophobic particles. In phosphate flotation tests a direct correlation was observed between froth viscosity and recovery and an inverse correlation between froth viscosity and grade. Phosphate flotation tests in the presence of a silica depressant indicated that higher froth viscosity is an effect rather than a cause of silica particles reporting in the froth.

Jan 1, 1992

By G. J. Hodges

The Stillwater Mining Company, a partnership of Pittsburg & Midway Coal Mining Co. and Manville Corporation, operates a precious metals smelter at Columbus, Montana to further up-grade concentrates from its platinum/palladium mine. The smelter began operation in the summer of 1990. The gas cleaning system in the facility utilizes "oxidation/dilute mode" dual-alkali scrubbing technology to capture sulfur oxide gases from the process gas streams. This paper describes the rationale for selecting the dilute mode dual-alkali system and summarizes design parameters. Start-up problems and their solutions are also discussed.

Jan 1, 1992

By I. L. Follington

A breaker line support (BLS) monitoring system, BLSmon, has been designed and constructed by the CSIRO and installed and commissioned at Laleham No.1 Colliery, Queensland. This system was designed to record hydraulic leg pressure and canopy position measurements and relay these, in real time, to the surface. The system has shown itself to be capable of operating on the BLSs without any adverse affect on production, Analysis of the results of the monitoring exercise has shown that rate of change of leg pressures on the BLSs could be used as an aid in the prediction of adverse mining conditions. Under favourable mining conditions the supports were observed to initially unload from the set pressure, this unloading reduced with time and by the end of a typical lift cycle had either ceased or reversed slightly. This behaviour was considered to be due to one of four possible causes, these being; the compaction of floor debris, and/or compaction of the floor, and/or crushing of the roof and /or support creep. The actual cause can only be determined through detailed monitoring of both roof and support convergence. However observational data would suggest that compaction of debris and softened floor material beneath the supports was the most likely cause. The few positive loading rates recorded under these conditions were of short duration and occurred towards the end of individual lifts. Where mining conditions were unfavourable the negative rates of change of pressure, unloading of the support, were reduced throughout a lift, in both duration and magnitude, when compared with favourable mining conditions. Over the same period the positive rates of change were observed to be greater. The rate of change of loading and convergence can be utilised to identify the onset of instability in the lift area. However, before this facility can be utilised by the mine for the reliable prediction of instability more monitored data and sophisticated processing techniques are required. A mechanism has been postulated for the deformation behaviour of the roof and pillars in a mechanised pillar extraction operation from the continuously monitored data, observational data and results of previous studies. The 7 m wide fenders were observed to yield under abutment stresses before lifting commenced. The stability of these fenders throughout the lifting sequence was considered to be dependant upon the magnitude of their post peak load carrying capability. This is influenced by the post peak stiffness and the extent of roof lowering in the vicinity of the fender. Difficulties with fender extraction occurred where remnant coal left standing in the goaf caused uncaved goat to bridge to the mined fender. Difficulties were also experienced where sub-vertical jointing occurred in the roof of the split reducing it's ability to bridge effectively. Despite the relatively short monitoring period, the potential role and application of continuous monitoring in advancing understanding of the rock mass response to mechanised pillar extraction operations has been demonstrated. This understanding now requires enhancement and shows great potential for aiding the optimisation of mechanised pillar extraction operations.

Jan 1, 1992

By M. Polat

A combined heavy medium-flotation process which incorporates the advantages of two widely employed cleaning methods, namely, heavy medium separation and flotation was used to achieve improved separation of coal from ash at fine sizes and to recover the heavy medium as a substantially recyclable product. The investigation was carried out in two successive phases. In the first phase, tests were performed to deter-mine the effect of different variables such as the medium density, flotation time, magnetite type, etc. on the efficiency of the process using in-plant samples from Homer City Coal Preparation Plant. In the second phase, the optimum conditions determined in the first phase were employed to determine the applicability of the process to a few Central Pennsylvania coals. It was observed that the process was very effective in recovering the magnetite. In most of the cases investigated, the magnetite was separated from the non-magnetic material at approximate-1 to 99 % recovery with a grade ranging from 95 to 99 %. The grade of magnetite decreased with increase in ash content of coal and with decrease in size of magnetite.

Jan 1, 1992

By Gary K. Elliott

Many industrial processes generate hot waste gases which contain particulate pollutants. Conventional clean-up techniques suffer limitations either because collection efficiency is low or because the gas must be cooled before treatment. thereby increasing costs and preventing energy recovery. The application of increasingly stringent environmental legislation to the non- ferrous metallurgical industry Is presently illustrating these conventional technology limitations. Low density ceramic media allow filtration to take place at high temperatures and are now rapidly becoming accepted in many industries. This paper reviews experiences with a proprietary low density ceramic filter element, Cerafill. It includes consideration of the structure, composition. typical operating and case studies with particular reference to non-ferrous metallurgical furnace applications.

Jan 1, 1992

By S. B. Bhagwat

The United States has abundant coal resources that could last at least another century. and probably longer at present consumption rates. Geographically, the coal resources are distributed over the entire nation including Alaska, although there are no coal deposits in the highly populated areas on the two coasts. This allows free access to the coal, but makes transportation more expensive. Not all coals can be utilized equally because they differ vastly in quality. The sulfur content of coals, considered as the most detrimental acid rain-causing element, varies from as low as 0.3 percent in some areas of the western U.S. to 5 percent or more in parts of the Midwest. The chlorine content, which causes corrosion of plant hardware, also varies regionally. The 1990 amendments of the Clean Air Act of 1963 (CAA) require that emissions of sulfur be restricted and rolled back in two stages by the year 2000. There have been a number of reports expressing concern about the future of the industry in the states where high sulfur coal is produced. The remedies devised by the federal government and many coal-producing states in the past to "se-cure" the future of the regional coal industries have focused on the physical task of removing sulfur rather than the economic challenge of doing so at a cost that will enable high-sulfur coals to survive and compete. The past remedies, generally, were not specific enough to account for the characteristics of regional coal deposits and did not look at the coal market as an integrated national and international entity. The State of Illinois has, in recent years, taken a more comprehensive approach to the solution of the problem.

Jan 1, 1992

By George A. Morgan

The production and processing of crude petroleum and natural gas are the dominant economic sectors of the Middle East. The IS countries that constitute the region accounted for 26% of world crude petroleum output, 17% of world natural gas plant liquid production, and almost S% of world dry natural gas production. About 66% of total world crude petroleum reserves and 31 % of total world natural gas reserves are in the Middle East. Transportation and port facilities in the region are geared to expediting efficient and rapid shipment of these materials. U.S.-dollar-denominated export sales of these fuels, estimated at $120 billion in 1989, provide funding for further diversification of the mineral industry. This is usually through development of downstream facilities for producing energy intensive metals such as aluminum and byproducts of the fuels such as petro-chemicals and fertilizers. Earnings from the industry are also channeled by sever-al Governments in the region to mineral industry projects in Africa and elsewhere. A fairly wide range of nonfuel minerals is produced in the region. However, the variety of minerals produced, output levels, and the size of the overall nonfuel mineral economy is dominated by Iran and Turkey. Turkey, with a diverse mineral production and strategically situated between Europe and the Middle East, ranked among the top three world producers of boron, chromite, pumice, and strontium. It was also a significant world producer of magnesium com-pounds, mercury, and sodium sulfate. Iran had generally lower output owing to 9 years of neglect to the mining sector between 1979 and 1988. It was a significant producer of gypsum and fifth in world production of strontium. Despite a very small domestic mineral industry, Israel was second in world production of bro-mine and a significant producer of phosphate rock and potash. Jordan ranked fifth in world production of phosphate rock. Iraq ranked about eighth in world production of sulfur, a commodity of major importance in the metallurgical, petrochemical, and fertilizer industries.

Jan 1, 1992

By Da Zhao Gu

An important problem in rock engineering is to control the properties of artificial rock. A compaction technique for casting artificial rock specimens with controlled properties is described, i.e. using a compression-testing machine to compress the mixture. Uniform density is necessary to achieve uniformity of properties of the specimens, and uniform density can be obtained by using the specific pressing method presented. Rebound and borax content are important to the technique and have been studied as well.

Jan 1, 1992

By William J. McDonough

Advanced materials are polymers, metals, and ceramics fabricated as intermaterial compounds, alloys, or composites. The resultant components have higher strength-to-density ratios, greater hardness and wear resistance, and one or more superior thermal, electrical, or optical properties when compared with traditional materials. Advanced materials, the basis for many of today's emerging technologies, offer savings in total energy consumption, improved performance at reasonable cost, and less dependence on imports of strategic and critical mineral resources.

Jan 1, 1992

By Medhurst TP, Trueman R, Hutchinson IN

A breaker line support (BLS) monitoring system, BLSmon, has been designed and constructed by the CSIRO and installed and commissioned at Laleham No.] Colliery, Queensland. This system was designed to record hydraulic leg pressure and canopy position measurements and relay these, in real time, to the surface. The system has shown itself to be capable of operating on the BLSs without any adverse affect on production. Analysis of the results of the monitoring exercise has shown that rate of change of leg pressures on the BLSs could be used as an aid in the prediction of adverse mining conditions. Under favourable mining conditions the supports were observed to initially unload from the set pressure, this unloading reduced with time and by the end of a typical lift cycle had either ceased or reversed slightly. This behaviour was considered to be due to one of four possible causes, these being; the compaction of floor debris, and/or compaction of the floor, and/or crushing of the roof and /or support creep. The actual cause can only be determined through detailed monitoring of both roof and support convergence. However observational data would suggest that compaction of debris and softened floor material beneath the supports was the most likely cause. The few positive loading rates recorded under these conditions were of short duration and occurred towards the end of individual lifts. Where mining conditions were unfavourable the negative rates of change of pressure, unloading of the support, were reduced throughout a lift, in both duration and magnitude, when compared with favourable mining conditions. Over the same period the positive rates of change were observed to be greater. The rate of change of loading and convergence can be utilised to identify the onset of instability in the lift area. However, before this facility can be utilised by the mine for the reliable prediction of instability more monitored data and sophisticated processing techniques are required.

Jan 1, 1992

By G. Skybey

The Skybolt is a new bolt concept, point anchored with resin in large diameter holes of specific sizes 38 mm and 45 mm. The new design achieves the optimum annular spacing required for mixing the resin anchor components which is essential for optimum resin bonding of the bolt to the surrounding rock. This paper explains the load transfer mechanisms between bolt/resin/rock, unique to this bolt concept. It compares the pull-out test results to those of paddle and expansion shell type bolts, and highlights the versatility of Skybolt over existing, currently used, rock support systems and the benefits mine operators can achieve when using the Skybolt.

Jan 1, 1992

By Walter Hoecker

The dissolution of gold in cyanide_ leaching has been we11 published with the genera1 acceptance that gold is oxidised by oxygen and stabilized by complexation with cyanide [1]. The dissolution of gold is essentially an electrochemical process. The rate of the anodic gold dissolution is controlled by the cyanide concentration. - (2) While the cathode reduction of oxygen is controlled by dissolved oxygen concentration - (3) There are a number of factors influencing the concentration of oxygen, and if 1owered substanth.lly will effect the efficiency of the leaching plant. These include: "' salinity "' temperature "'partial pressure "'oxygen consumption rate The use of pure oxygen for· cyanidation is only beneficial if oxygen is rate limiting, Conversely a slurry saturated with air (typically 5 - 8 ppm) may not be enough for maximum leach rate. The diagram below shows the maximum dissolved oxygen levels obtainable with pure oxygen and air. DISSOLVED OXYGEN (MAXIMUM) IN WATER At steady state, the rate of the cathodic reaction must equal the rate of the anodic reaction. Thus the rate of gold dissolution is dependent on both the· cyanide and oxygen concentrations. - (4) Using an average of Do/Den =· 1.5 [2] (where Do and Den are the oxygen and cyanide diffusion coefficients) the table below illustrates the maximum effective oxygen concentrations for given cyanide levels in clean water [3].

Jan 1, 1992

By Frank Ladwig, Stephen Gos

Tailings and/or wastewater generated from gold extraction plants employing cyanida­ tion must often be treated to remove the cyanides and heavy metals for environmental reasons and/or gold extraction inhibition reasons, due to the presence of heavy metals like copper, which have a detrimen­ tal effect during cyanidation. In recent years, the treatment of effluents contain­ ing cyanides and heavy metals has been widely studied, Among chemical treatment methods, the use of hydrogen peroxide has been universally employed as a viable option. However, in some cases, effluents containing high concentrations of heavy metals and/or solids decompose the hydrogen peroxide, an undesirable side reaction. The addition of stabilizers or other peroxygen compounds together with hydrogen peroxide can, however, considerably reduce the rate of decomposition and thus result in detoxi­ fication costs, which are considerably less than the standard detoxification process using hydrogen peroxide. In some cases, the reaction rate can also be increased, resul­ ting in lower investment costs for new detoxification plants. This paper deals with the results of developmental work performed in the recent past and introduces some new processes with the aim of optimizing reagent consumption and costs.

Jan 1, 1992

By Dennis R. Rice

The Kettle River Joint Venture is 70 percent owned by Echo Bay Minerals Company, a wholly-owned subsidiary of Echo Bay Mines Limited, and 30 percent owned by Crown Resources. Initial announced ore reserves were 700,000 troy ounces of gold contained in three deposits located east and north of Republic, WA., U.S.A. Additional reserves are being proven. Processing of finely ground ore by preaeration-carbon in leach (CIL) circuit was selected followed by cyanide destruction by the INCO Air/SO2 process.

Jan 1, 1992

By James Y. Oldshue, Paul M. Kubera

Ore processing requirements in the gold industry are similar to those in other sectors of the minerals industry. In all cases, the processes revolve around the handling of large volumes of ore slurry, incorporating either physical processing or chemical processing steps which are related to distinct mixing application classes as defined in Table 1. From this standpoint, the complexity of the applications range from the simple (blending, solid suspension, etc.) to the complex (e.g., multi-phase reactor systems). The large volume of material to be processed dictates the large equipment size which is characteristic of this industry, and the often remote locations place a premium on both mechanical and process reliability.

Jan 1, 1992

By C. A. Fleming, C. J. Ferron, E. S. Makande, P. Mason

Several small mines are producing refractory gold concentrates in Zimbabwe and, owing to the small scale of most of these operations, their output is processed in a central custom roaster in Kwekwe. Owing to the wide variations in the feed to the roaster, the efficiency of the old Edwards roaster is deemed unsatisfactory with gold recovery from concentrate as low as 70%, and alternative processes were evaluated to improve this situation. Various processes for oxidizing refractory arsenopyrite/pyrite concentrates to liberate gold prior to cyanidation are known. In practice, only two have to date met with wide industrial acceptance, pressure oxidation and roasting. Owing to the ·high arsenic and antimony levels of some concentrates in Zimbabwe, the only viable roasting alternative would be two-stage air-roasting of concentrates in two reactors, as practiced at Giant Yellowknife, Campbell Red Lake and New Consort. This process, however, creates an arsenic disposal problem, and produces gas of fairly low SO2 content, requiring a large gas handling system for acid production. On the other hand, there are currently four commercial pressure oxidation plants treating refractory gold ores (McLaughlin, Mercur, Getchell and Goldstrike) and three treating concentrates (Sao Bento, Porgera, Campbell). One other concentrate oxidation plant is being constructed (Con), and several more are being considered.

Jan 1, 1992

By Kenneth L. Myers

The net balance of the inflow and outflow of water in a tailings storage facility has major economic implications in any large mining and milling operation. In a net precipitation environment it can control the ultimate size and storage capacity of a facility or dictate the need for an expensive treatment and discharge program. In a net evaporation environment it can control the extent of the water rights acquisitions required for makeup water and dictate the number and size of expensive wells and pumping and delivery systems. The elements considered in a water balance analysis include the anticipated production rate, the water content of the slurry used to deliver the tailings, inflow from precipitation and snowmelt, and losses from evaporation and seepage. The mine can exert significant control over only one of these elements: the production rate. All others are subject to considerable uncertainty from month to month and year to year. The traditional approach is to analyze in a spreadsheet environment by making simplifying assumptions and using monthly mean or "average" values for precipitation inflows and evaporation losses. Often the analysis will be repeated with values subjectively assigned to represent a "wet" year or "dry'' year. The probabilistic approach uses the same basic spreadsheet model in conjunction with a probabilistic simulation add-in program allowing probability distributions to be substituted for any of the deterministic variables. The resulting analysis shows the full range of variation possible for each parameter of interest (i.e., available return water, makeup water required, storage, seepage losses) and estimates the exceedance probabilities for each. The potential uses and advantages of the probabilistic approach are discussed.

Jan 1, 1992

By W. Baguley

There are many carbon-in-pulp and resin-in-pulp screening devices which are at present in use in the South African mining industry. Each one of these screens has been an improvement, from the very basic air cleaned and 'EPAC' types which were either circumferential or · diametrical launder screens, which were developed for C I P in the early 1980's, through to the more sophisticated LAP and Kambalda Screens. Each one of these screens not only increased the performance or throughput per square metre than its predecessor, but also addressed maintenance problems, wear, reliability and the ability to handle surge conditions, thereby preventing tank overflow. However, very little theory has been presented concerning, the flow of pulp through internal screens, carbon loss and screen wear rates. Almost all this information is based on empirical data. The NKM screen continued this trend and was able to offer flow rates in excess of 180 cubic metres per square metre of screen per hour and an average screen life of approximately six months. However, with increasing sophistication of the screen and the use of wedge wire as opposed to the normal woven wire, the mass was significantly increased and costs began to mount. Therefore, Mixtec undertook to develop a radically different screen, which incorporated many of the advantages of .the existing equipment and combined a few of its own.

Jan 1, 1992

By Brian D. Smith, Batric Pesic

Typical sulfide gold bearing ores are refractory to standard cyanidation practice. This type of ore always needs some form of oxidative pretreatment to destroy the original host mineral matrix to make the cyanidation possible. The oxidative pretreatment can be achieved by roasting, autoclave leaching, bioleaching, or some other chemical method. Today, the most common practice of ore oxidation is either roasting or pressure leaching. The other methods are still considered developmental.

Jan 1, 1992