Search Documents

Fluid circulation occurs in oceanic crust of all ages, at the seafloor spreading axis, on mid-ocean ridge flanks, in the ocean basins, and in subduction zones. In the first three settings the fluid originates as seawater. At the axis and on the ridge flanks, the circulating seawater produces a major chemical exchange between the oceans and the crust. Based on heat budget constraints, between 10 and 40% of the river flux of Mg can be taken up during high-temperature alteration of the basaltic crust along the mid-ocean ridge axis. Most of the hydrothermal -heat loss, however, occurs on the mid-ocean ridge flanks, where the temperatures are lower and the seawater flux correspondingly larger. The estimated heat loss on the flanks is so large that upwelling must occur over a large fraction (5-30%) of the seafloor less than 65 Ma in age, at seepage velocities on the order of 10 to 100 cm/yr. The circulating seawater need lose less than 1 to 2% of its Mg content in order to solve the Mg mass balance for the oceans. Fluids in subduction zones are commonly less saline than seawater and are rich in methane and other light hydrocarbons. These fluids may originate by dewatering of the downgoing slab. If so, they may close the geochemical cycle of H2O that began with hydration of the basaltic crust at the ridge axis.

Jan 1, 1990

By W. E. Wallace, B. L. Razzaboni, P. Bolsaitis, M. J. Keane

"Therma1 and chemical treatment of respirable size silica dusts samples is shown to induce marked changes in their hemolytic activity. The cytotoxicity of crystalline a-quartz (Min-U-Sil), and fumed silica (Cab-0- Sil) particles, as measured by a hemolytic activity protocol, is decreased by calcination and can be related to the dehydroxylation of the surface. The hemolytic activity of P-cristobalite particles of respirable dust si7.e was also determined and found to be lower than that of a-quartz. The change in the surface structure resulting from thermal treatment is detectable by photo-acoustic infrared spectroscopy and zeta-potential measurements. The absorption band in the 3200-4000 cm-1 frequency region of both Cab-0-Sil and MinU- Sil disappears upon heat treatment while a sharp band, identified with single silanol groups, at 3750 cm-1 increases in intensity. The zeta potential-pH profile, in the pH range of 4.0-7 .0, of the calcined, siloxane surfaced particles is more negative than that of material with a silanol surface.The cytotoxicity of the crystalline and fumed silica dusts was also found to be strongly dependent on particle size. Fumed silica of large surface area (small particle size) exhibits an initial increase in hemolytic activity upon calcination. This result confirms other experimental observations pointing to a particle size of maximum toxicity. INTRODOCTIONThe toxicity of silica and other mineral particles, as manifested by their role in inducing pneumoconiosis, fibrosis, silicosis and other pulmonary disorders is largely traceable to the characteristics of particle surfaces and to particle morphology. The great wealth of data on the physical and chemical properties of silica is still insufficient for a comprehensive understanding of the specific parameters to be associated with fibrogenic activity and, correspondingly, with the optimum means for characterizing and quantifying the toxicity of dusts, and the design of possible preventive or therapeutic methods.The great diversity of parameters that have been proposed and tested for correlation with cytotoxicity suggest that more than one mechanism may be involved in the fibrotic activity of silica particles. The crystalline structure of the material (more active tridymite versus less active crisobalite and passive stishovite), freshly formed surfaces and free radicals associated therewith, silicic acid adsorbed onto silica surfaces, the concentration of hydroxyl groups at silica surfaces, particle size and morphology, among other properties, have been investigated and found to conelate in tests of cytotoxicity."

Jan 1, 1990

Mr G H Park was born and brought up in Zimbabwe, in mining from the University of the Witwatersrand. Starting as a Learner Official at Rand Mines, he went Mr D J van Niekerk was educated at Helpmekaar Boys' High School in Johannesburg and the University of Pretoria. Mr C J C Janse van Vuuren was educated at Klerksdorp High School, Pretoria Technical Colege, the University of Pretoria, and Unisa. He holds the folowing degrees: BSc (I&S), BSc Hons (Met Pta), ND (Met Tech), AEP (Unisa). Prof. R F Sandenbergh was educated at the Afrikaanse Hoerskool Germiston and the University of Pretoria. He holds the degrees of B Ing (Chem), M Ing (Chem), and D Ing (Metal). President's Award Professor Jannie van Deventer, Head of the Department of Metalurgical Engineering at the University of Stelenbosch, has been honoured with one of the five President's Awards for 1990. These awards are made by the CSIR's Foundation for Research Development. G R Bozzoli Awards* Prof. Alan Kemp, Dean of the Faculty of Engineering at the University of the Witwatersrand, has appealed to industry not to cut bursary funding during recessionary times.

Jan 1, 1990

Pictured on these pages are the eight RMCMI Scholarship Award Winners for the 1989-1990 year followed by a brief profile. All winners, except Emmet Roache from New Mexico, were present as guests of the Institute at the June convention in Steamboat Springs, Colorado to receive recognition at the Welcome Session Monday, June 25, 1990. Each state vice president served as the host for the collegiate winner. In addition to receiving a plaque from the Scholarship Chairman, Dr. Donald Gentry, each winner receives $750 tuition credit for the coming academic year. As this is a continuing award, the winners from the previous year will receive another $750 for tuition credit in their senior year if they have maintained good academic standing and are recommended by their university. Criteria for these awards to be made in the spring annually is (1) That the award be made to a sophomore student and used as tuition during the junior year. (2) That the recipient be both a U.S. citizen and a resident of the state involved. (3) That the recipient have good academic standing, be pursuing a degree in a mining related field and have an expressed interest in Western coal as a possible career path. The scholarship program includes curricula other than those in the mining departments, but in the engineering disciplines, such as geology, mineral processing and metallurgy. Contributions to this worthy project are tax deductible to each individual RMCMI member or his firm. Through annual donations of $100 or more, the Patrons of the Institute fund the scholarship program, and the various vice presidents contribute the travel expenses to conventions for these outstanding young collegiates. Donations to this worthwhile program may be made payable to RMCMI Scholarship and mailed to the RMCMI Office, 3000 Youngfield Street, Suite 324, Lakewood, CO 80215. Profiles of the 1990 Scholarship Winners follow. [ ] Mildred Benally University of Arizona Tuscan, Arizona Mildred has attended San Juan College in New Mexico, and will graduate from the University of Arizona in May, 1991. Upon completion of her, schooling she hopes to pursue a career in the coal mining industry. In preparation for her goal, her work experience includes being a lab technician, a mining engineer intern, and a lab technician assistant; she also is very skilled in various computer applications. She has been a member of SME-AIME, and secretary to the U of A Student Chapter, and recipient of the SME Coal Division Scholarship and past recipient of the Navajo Tribal Scholarship. [ ] Joshua Olmsted Colorado School of Mines Golden, Colorado Josh is a sophomore majoring in mining engineering at the Colorado School of Mines. He is an outstanding student as well as an accomplished athlete. Josh was on the Academic Honor Roll 1988-1989 and has been awarded an athletic scholarship. He plays varsity soccer and intramural basketball.

Jan 1, 1990

In this paper, the authors attempt to apply a simplified non-homogeneous void diffusion model (NHVDM) to predict surface subsidence for longwall mining in Illinois. A generalized error function subsidence profile is derived from this model. The model validation indicates that the NHVDM approach appears to fit the observed subsidence data as well or better than the error and the trigonometric functions, particularly around the trough edge areas.

Jan 1, 1990

Many mining operations are uncertain of what costs they should be achieving. The majority of cost estimates are based on historical costs that have added contingency factors. Historical costs are a valuable source of information but a more precise costing method is necessary. There are several alternative methods for predicting costs. A methodology which provides the best indication of the achievable costs is one using a standard inventory list and a bill of quantities. The model is termed a Basic Principles model and addresses basic design principles and engineering constraints.

Jan 1, 1990

By Larry T. Yano, Gerald T. Handford

"Tailings Engineering has the responsibility for planning and coordinating tailings disposal and for ensuring the stability of the tailings dyke. The inclusion of both the planning and geotechnical functions in one team has resulted in greater efficiency in the design and planning process. Major challenges in tailings disposal facing Syncrude are in the areas of: (1) sludge disposal; (2) instrumentation and monitoring; and (3) liquefaction. Meeting these challenges will have a significant effect on the cost effectiveness and reliability of the mining operation.IntroductionThe size of the tailings disposal operation has led to the establishment of a large engineering team devoted solely to the disposal of tailings. This paper discusses: the tailings disposal operation, the role of tailings engineering, the organization, inter faces, and the present and future challenges with respect to tailings disposal."

Jan 1, 1990

By F. Tailoka

Microporous membranes have been used to create a very fine dispersion of bubbles which greatly enhances the mass transfer of electroactive species to the electrode. Using this system, it has been shown that it is possible to electrowin copper as a coherent planar deposit, at high current densities, from copper chloride solutions.

Jan 1, 1990

By P. Cowx

The carbothermic reduction of zinc oxide rich Electric Arc Furnace baghouse dust in the Tetronics transferred arc plasma furnace to produce a non-toxic slag and a metallic zinc product is described. In particular, the operation of the zinc splash condenser coupled to the plasma furnace is examined and the effect of process variables on zinc recovery is discussed.

Jan 1, 1990

By William J. Neely

Augercast piles are formed by drilling a continuous-flight auger into the ground and, on reaching the required depth, sand-cement grout or concrete is pumped down the hollow stem as the auger is withdrawn. The sides of the hole are supported at all times by the soil-filled auger, eliminating the need for temporary casing or bentonite slurry. The augercast piling method is fast and economical; there is no vibration, very little noise and, if executed properly, no ground displacements during installation. The method is well suited to sands which are easy to drill and are readily transported up the auger. Relatively little attention has been given to augercast piles in the literature which might be part of the reason for the considerable variations in local practice, building code requirements and design methods. The purpose of this paper is to discuss some of the features of augercast pile installation that are known to influence both the structural and geotechnical capacity of the pile, to evaluate several empirical design methods and to look at some important aspects of quality control of augercast pile installation.

Jan 1, 1990

By M. R. Yenchek

The U.S. Bureau of Mines designed and constructed sensitive and coordination-free ground-fault relays (GFR's) for use on mine power systems. First, a list of GFR attributes for mine ac utilization applications was compiled. These practical guidelines specified design, construction, transient immunity, reliability, and operating criteria. The time-current characteristics of the ac and dc units, subsequently fabricated, were designed to be below the human electrocution threshold. The significant and highly variable capacitance of high-voltage distribution cables was found to preclude the sensing of ground currents in the milliampere range. However, the coordination-free system developed for high-voltage distribution should enhance safety by significantly decreasing response time to ground faults. Implementation of the sensitive GFR technology in the mining industry has the potential to eliminate the majority of injuries and nearly all the deaths resulting from contact with energized components.

Jan 1, 1990

To generate a most profitable ultimate pit limit is generally the first step in mine design. This paper presents a new graph theory oriented, optimum ultimate pit limit design algorithm which will maximize the total undiscounted net profit. This algorithm performs much better than the well known Lerchs-Grossmann algorithm, in terms of the reduction in computation time and computer memory requirements. This algorithm operates on many directed trees in a graph, where each vertex in a tree represents a block in the mine model. The formation of each directed tree is based more on the ore-waste support concept than the geometry constraints alone. The general procedures of the algorithm, programming considerations and two case study results are discussed in the paper.

Jan 1, 1990

By R. C. Moe

Pelletizing studies were conducted to find ways of improving the metallurgical properties of acid and fluxed pellets. In acid pellets, melting temperature was controlled by the formation of low melting temperature fayalite during reduction. Formation of a permeable metallic shell during reduction allows diffusion of reducing gas to the pellet core, decreasing fayalite formation. With fluxed pellets, slag chemistry had the main influence on metallurgical properties. Mineralogical, chemical and structural transformations that occur during reduction were studied at various intervals for a number of Mesabi Range pellet types. Six pellet types were selected for further investigation based on significant differences in softening/melting characteristics. Retention of porosity in the metallic shell was found to be the overriding factor in determining softening/melting behavior.

Jan 1, 1990

Natural Gas has been available in New Zealand for twenty years. During that time the gas share of the energy market has grown and now natural gas forms a significant part of New Zealand's energy scene, helping consumers to achieve a higher standard of living, and reducing dependence upon imported oil.Natural gas is now used for petrochemical manufacture and power generation in addition to direct supply to consumers.As concern for the environment continues to build, natural gas will have an increasingly important role to fill in these markets. This paper sets out the background to the development of natural gas in New Zealand and identifies the current markets. It then looks at those matters which are likely to influence the role of natural gas in the 1990s.

Jan 1, 1990

By R. E. Snow

The analysis of ground water inflow and discharge from underground mines has received increased attention in recent years due to environmental issues which must be addressed under current state regulations for coal mining and processing operations. In particular, coal operators must assess the probable hydrologic consequences associated with mining activities, and must plan for mine water handling during operation and following completion of mining. The prediction of ground water inflow rates with future mine development allows preparation for potential operational problem and identification of inflow reduction methods. Similarly, evaluation of mine discharge rates is necessary to address potential long-term acid mine drainage (AND) concerns. As part of mine discharge analyses, methods. to control seepage and AMD can be considered. The objective of this paper is to discuss the practical applications of mine inflow and discharge analysis, describe the typical flow components, outline the procedures necessary to perform the analysis, and illustrate the modeling procedures and potential results of mine inflow and discharge predictions.

Jan 1, 1990

By J. W. Leonard, D. A. Newman

By using physical and chemical means to increase the bulk density of newly broken coal freed from the mine face, the potential to improve coal mine productivity is significantly enhanced. It is estimated that by increasing bulk density, greater tonnages can be placed in fixed volume scoops and shuttles cars to improve production by as much as 10% to 20%. Such improved packaging to achieve new levels of volumetric efficiency might require only small and easy to implement changes to present downstream mining operations. Opportunities exist for improving broken coal bulk density from the moment of breakage, during transport across the continuous miner or loading machine, during discharge into the haulage unit, and after placement in the haulage unit. Physical/chemical methods for broken coal compaction in mobile, fixed volume units in underground operations are discussed.

Jan 1, 1990

By Ralph P. Hackl

Ore at the Congress gold property, located near Goldbridge, British Columbia, is extremely refractory with most of the gold disseminated in fine-grained arsenopyrite. Metallurgical testwork conducted by Giant Bay Biotech Inc. indicated that biooxidation pretreatment was capable of increasing cyanide gold recovery from the ore to greater than 90%. To determine if the bioleach process could be successfully scaled up, a 225m' (7950-cu ft) commercial size bioleach reactor was built and tested at the mine site in 1989. At that time, the tank was the largest bioleach reactor ever operated. The objectives of the program were: • to ascertain if the biooxidation rates obtained in lab and pilot-scale reactors could be duplicated in a commercial scale tank; • to identify agitation conditions under which the process will function optimally; and • to demonstrate the bioleach process on a scale sufficient to satisfy the owners and potential investors.

Jan 1, 1990

By Edward F. Divers

Tills U.S. Bureau of Mines report briefly evaluates the advantages and disadvantages of basic dust control techniques presently used by U.S. coal preparation and mineral processing plants. These include ventilation, baghouse-type collectors, wet scrubbers, electrostatic precipitators, source control, sprays, good housekeeping, and personal protection devices. Two specific problems in these types of operations are also considered: dust collector system duct clogging, and control room dust control. Information provided in this report results from dust control research projects conducted by the Bureau at various coal preparation and mineral processing plants over the past decade to reduce workers' dust exposure. These studies indicate that plant ventilation systems normally provide the most cost effective method for dust control. Baghouses and scrubbers were also effective in specific applications, and examples of each are given. In extreme dust conditions, personal protection devices, such as respirators or the dust helmet, can also be highly cost effective.

Jan 1, 1990

By Ricardo D. Presnell, Erich U. Petersen, William J. Tafuri, Donald M. Hausen, Russell C. Babcock, William L. Gunter, Thomas R. Gibson, Douglas N. Halbe, Jay W. Hammitt

The Barneys Canyon orebody is a sediment-hosted disseminated gold deposit located 8 km (5 miles) north of the Bingham Canyon porphyry copper mine. Mineable oxide reserves are 8.6 million tonnes (9.5 million short tons) grading 1.64 g/tonne (0.048 oz/ton) gold. Host lithologies are carbonates and siliciclastics of the Park City and Kirkman-Diamond Creek Formations of Lower Permian age. Gold distributions are controlled by favorable stratigraphic units and associated alteration, and structures. Dominant alteration is decalcification and bleaching of carbonates, and argillization and bleaching of sandstones. Gold to silver ratios are greater than 1:1. Anomalous trace metals include arsenic, antimony, mercury and thallium. The Melco deposit lies 2.4 km (1.5 miles) southwest of the Barneys Canyon deposit. It is spatially associated with a steeply northwest-dipping siliciclastic breccia in the Kirkman-Diamond Creek Formation at the contact with underlying orthoquartzites of the Freeman Peak Formation. Both gold-bearing oxidized and sulfide lithologies are present, often in sharp contact. Mineable oxide reserves are 2.8 million tonnes (3.1 million short tons) grading 2.40 g/tonne (0.07 oz/ton) gold. Anomolous trace metals include arsenic, antimony, mercury and thallium, which are generally present in concentrations greater than those at Barneys Canyon, particularly in sulfide-bearing material. A spatial, temporal and genetic relationship is proposed between the Melco deposit and late-stage gold mineralization at Bingham Canyon, although both the Melco and Barneys Canyon deposits have many similarities to Carlin-type gold deposits.

Jan 1, 1990

By Thomas C. Palangio

Since the advent of explosives, people have been trying to mechanize the process of loading it into long, narrow holes. Automated loading frees manpower from the arduous task of charging granular, cartridged and slurry explosives. An unexpected bonus of the automation process has been the realization of some valuable side effects such as high throughputs which speed up the loading process and higher loading densities which enhance explosive performance and permit hole patterns to be expanded.

Jan 1, 1990