Search Documents

By Eric R. Bauer

This U.S. Bureau of Mines study was conducted to gain a basis for recommending methods to predict and prevent the occurrence of cutter roof failure, a common ground control problem in mines of the Northern Appalachian Coal Basin. This was accomplished by determining the geologic and engineering factors responsible for cutter development at six mines affected by cutter roof failure. Three distinct factors were found to be initiators of cutter roof failure: (1) high horizontal roof stress, (2) surface topographic variations, and (3) geologic anomalies. Effective control of cutter roof was obtained through improved bolting techniques, entry and mine reorientation, and entry and pillar size modifications, but only when selected based on the actual cause of failure.

Jan 1, 1990

By Turner WG, Short RR

Obviously, the paramount advantages of contract mining have been recognised by mine developers throughout Australia, as evidenced by surface gold mining operations of significant output almost exclusively being performed under contract. These paramount advantages of using an experienced professionally managed contractor result from the mine developer being freed from financing the required relatively large capital expenditure at current relatively high interest rates or in a capital scarce stock market, and from the need to recruit and sustain a large operating work force in a competitive labour market.

Jan 1, 1990

The cost of preparing a feasibility study is notoriously difficult to estimate. Studies for mining projects are typically commenced when an exploration programme has identified a mineable resource and pre-feasibility studies have shown that development of the resource would lead to an economically viable project. Pre-feasibility studies will normally include an estimate of the cost of a formal feasibility study and this estimate would then be firmed up before a commitment is made to proceed with the formal study. Data for preparing the feasibility study cost estimate will be sketchy, geological investigations, metallurgical testwork, and marketing studies may be needed before the scope of the project and hence the scope of the formal study can be finally determined. Before an estimate of the work required and hence of the cost of the feasibility study can be prepared the source of project funds must be decided. Studies for internally funded projects are often less rigorous than those which must be "bankable" and subject to the scrutiny of external financial institutions. This paper sets out suggestions for preparing more accurate cost estimates for feasibility studies by ensuring that all activities are included and shows how a staged approach to preparing such studies can minimise costs and guard against cost overruns. It also provides a case study showing how the estimate compared with actual costs for a recent feasibility study completed by Pancontinental Mining Limited.

Jan 1, 1990

By H. V. Fairbanks

The following processes were investigated using ultrasonic treatment in mineral recovery: (1) cleaning coal from coal slurry ponds, and (2) extracting precious metals from tailings and other sources. The treatment entails the production of a water slurry of the material containing the mineral which is made to flow over the vibrating surface of the ultrasonic treatment unit. The vibrations transmitted into the slurry break up particle agglomerates and also produce a scrubbing action on the surfaces of the particles. The treated mineral particles were found to have increased settling rates, better compaction, and more rapid water drainage.

Jan 1, 1990

By Steven B. Van Kouteren

Value added is a loosely used qualifier in the industrial minerals industry. What exactly does it mean? What does it take to make a value-added product? More importantly, how does a company maintain the value added to its products? Most people agree that value-added means the value of a mineral minus the cost to produce it. This is misleading, though, because producing value-added products does not necessarily guarantee the profitability of the products. In some cases, firms that make value-added products are not very profitable. It is important not only to understand how to make a value-added product but also how competitive forces in the market can erode the value added. Therefore, when looking at value-added opportunities, producers must understand how to obtain the value added and how to maintain that value. Four major factors limit a company's ability to add value to its products. This paper examines these factors. It uses the ground calcium carbonate and mica industries as examples.

Jan 1, 1990

By G. P. Hand

The purpose of this paper is to bring to your attention the various kinds of high performance graphites available today, their characteristics and possible applications. These materials are products of a proprietary high temperature technology developed by Superior Graphite Company. We feel we have only begun to tap the potential of this technology and the utilization of the resulting products. During the course of the paper, we shall investigate high purity, high performance graphites made from raw materials such as mined natural graphites, synthetic graphites and petroleum derivatives. We shall define their characteristics and resulting benefits to current applications, along with applications currently under development. It is our desire to stimulate speculation and development of current high performance graphites and their applications as well as ideas for new high performance products and applications. First, a little background about the process. The technology was developed through a concentrated R&D effort which culminated in 1976 in the construction of a unique furnace capable of continuously processing tonnage quantities of granular carbons at temperatures in excess of 2,500 degrees C. This process is capable of refining various carbonaceous raw materials, including natural graphites, to levels of purity and consistency that were previously unattainable in commercial quantities. Carbon contents in excess of 99.9% are currently being produced on a continuous flow-through basis. Since beginning operation in 1977, this plant, located in Hopkinsville, KY, has been expanded in stages to its present capacity of producing over 45,000 tons of purified graphites and graphitic carbons per year. In addition to the purification process, the technology used allows the introduction of selected elements into the carbon/graphite structure to provide additional benefits. Elements of interest include boron, silicon, copper, iron and rare earths. The characteristics of and applications for some of these products will be discussed later.

Jan 1, 1990

By John C. Stankus

To improve mine roof bolt performance, Jennmar Corporation commenced the design and development of a new roof control sys- tem. This new system designated "Insta'l Compression", not only improves safety, but is more cost efficient due to reduced amounts of resin needed per bolt installation. In this paper the research and development of this new system will be outlined. Much of the information presented will be actual test data from various underground operations in Alabama, Kentucky, and Pennsylvania. The development of this system will also cover the design of a new expansion shell, resin compression ring, anti- friction washer, and upgrading of material specifications.

Jan 1, 1990

The application of cost updating with the aid of cost indices is reviewed with particular regard to the mining industry. Examples of applicable cost index series are included with values given for the last ten years. The compilation of the indices is discussed with consideration given to the possible sources of error inherent in their application to specific mining cost problems.

Jan 1, 1990

By A. A. Abdul-Latif, A. Sahin

"The phosphate deposit, located in the Abu Tartur plateau between the Kharga and the Dakhla Oases in the southern part of the Western Desert of Egypt, is the largest of its kind in the country. The phosphates are found in two horizons referred to as the Lower and Upper Phosphate Horizons within the Late Campanian Sibaiya Formation which belongs to the Nubia Group.This paper presents the results of a geostatistical study on the main phosphorite bed at the base of the Lower Phosphate Horizon which contains almost all the commercial reserves in the area. After semivariogram modeling for the phosphate thickness and accumulation, ordinary block kriging was employed to estimate the values of these variables in blocks of400 m by 400 m dimensions. The kriging results, which are presented in the form of contour maps, can be of considerable use in both future exploration and exploitation of the deposit. The grade-tonnage relationship based on the grade estimates derived from the corresponding thickness and accumulation estimates indicates the existence of 453.9 x 105 tonnes of phosphate above a cut-off grade of 18% P2O5. The mean grade of this tonnage has been estimated to be 25.77% P205"

Jan 1, 1990

By Cynthia M. Walck, S. K. Grant, R. D. Hagni

The Post Gold deposit is located in the northern part of the Carlin trend. The mineralization at Post occurs in proximity to a Jurassic-Cretaceous composite stock. Most of the gold at Post is hosted by non-metamorphosed calcareous siltstone and highly altered diorite, adjacent to the low grade skarn. Endoskarn, exoskarn, hornfels and marble are developed outward from the intrusive. The skarn is composed dominantly of diopside, tightly intergrown with gannet, k -feldspar, and sphene. The highest grade gold values are adjacent to the skarn, which acted as a permeability barrier to fluid migration. Post is the first Carlin-type deposit at which a skarn has been recognized to play a significant role in the localization of gold.

Jan 1, 1990

By Barbara J. Arnold

A coal's size distribution, clay content and moisture content can affect its handling behavior, but the combined effects of these properties and the effects of other properties are not known. Research underway at CQ Inc.' s (formerly EPRI' S) Coal Quality Development Center (CQOC) and at Iowa State University (ISU) will answer these questions as part of a four-year project to develop a coal handleability index for utilities to use when specifying coals. This paper will present preliminary data from the first year of the project, which focused on obtaining data on the chemical and physical properties of various coals and their measured handling properties. Additionally, size, ash and moisture analyses and shear test data for several coals used at one power plant will be presented along with correlations between these physical and chemical properties and the measured handling properties. These data lead to the conclusion that, while moisture content-is the most important variable, the amount of -325M (-0.044 mm) coal fines is a significant factor in determining coal handling behavior.

Jan 1, 1990

By J. B. Webster

Health and Safety in the work place is of primary concern to the underground coal industry. Control of dust in the underground environment is of major importance in this concern. Utah Power and Light Mining Division has undertaken extensive studies to determine and control the various sources of respirable dust in underground high production sections. Determination of dust sources has been achieved by real-time aerosol sampling and standard gravimetric sampling on individuals and in various suspect locations. Some sources are diesel roadway dust, outby crushing, and handling equipment, face sloughing, water spray roll-back, and mining equipment. Once identified, the dust sources are suppressed or controlled and/or the workers are directed from areas of greatest potential exposure.

Jan 1, 1990

By G. L. Mowrey

A new coal interface detection (CID) method is under investigation by the U.S. Bureau of Mines. This novel concept is based on utilizing a passive infrared system (FIR) to measure temperature changes associated with the cutting of coal and adjacent strata. For this method to work successfully, a definite mechanical/hardness contrast must exist between coal and rock. Advantages include that FIR responds instantaneously at the coal-rock interface and it is minimally affected by dust and/or water sprays. Based on preliminary tests, results indicate that the PIR method can be applied successfully in mines having a hard immediate roof.

Jan 1, 1990

A major problem that has continued to plague the surface coal industry is blast induced damage to the coal seam. Atlas Powder Company has addresssed this situation through seven years of field research in full-scale production environments. Many operations across the United States have been evaluated.

Jan 1, 1990

By Henry E. Reed

This presentation is about a small company, Industrial Mineral Products, that was formed in 1972 with one product and one customer and by a series of value-added changes avoided disaster and increased sales many times over. The principal of the company stopped by my office in Seattle looking for industrial mineral opportunities in the Northwest. We got together and went through all the minerals in Ladoo's "Industrial Minerals" from Abrasives to Zircon to see if we could find something available on the vast holdings of the Burlington Northern. At that time one of our lessees was operating a silica sand mine near Ravensdale, Washington and indicated that he might be interested in selling out. This sounded interesting to my client and within two weeks the transaction was completed.

Jan 1, 1990

By Murray C. G

A database of over 1300 earthquakes has been used to investigate the relationship between seismicity and tectonics in two areas of eastern Queensland and NE New South Wales. These areas have been monitored by several networks that were installed primarily to monitor seismicity associated with the impounding of large reservoirs. Events that occurred prior to the installation of these networks have been excluded from the analysis because they have large uncertainties in location.Seismicity in SE Queensland and NE New South Wales is concentrated in the coastal regions. Activity also extends off the coast of Queensland and beyond the continental shelf. The coastal activity is mainly within the New England Fold Belt. An area of the fold belt overlain by the Clarence-Moreton Basin is also active. There is an area of activity near St. George that correlates to the Wunger Ridge. Fraser Island and the adjacent onshore area, near Maryborough, are notably aseismic.Within the New England Fold Belt there is a NNW trending zone of concentrated activity that includes the South D'Aguilar Block and the Esk Trough as far as Gayndah. The Nambour Basin, the Gympie Province, and the southern portion of the Yarrol Block are significantly less active.Composite focal mechanisms of several groups of accurately located earthquakes in SE Queensland indicate predominantly reverse faulting. This faulting is the result of the crust being compressed horizontally in a NE-SW direction.Activity in the Burdekin Falls Dam area of central eastern Queensland is confined to the Drummond and Bowen Basins. There is also significant activity offshore from Townsville and Bowen.

Jan 1, 1990

By M. W. Harmer

Laboratory test work, pilot plant testing and plant experience with wet, fine mesh screens is discussed. High frequency, low amplitude, fine mesh, wet screens were installed on the 6th cleaner concentrate stream. These screens produce a 60% oversize recovery split of the molybdenite concentrate that is of leached equivalent quality. The undersize stream is leached with 'hot ferric chloride to remove Pb and Cu contaminates before roasting or shipment to sulfide customers. This plant modification is a good example of using existing technology in an unconventional flow sheet to yield significant cost savings.

Jan 1, 1990

By Z. Yunquan

The flocculation and dispersion behaviors of microsize wolframite and quartz are systematically studied in this paper. For synthetic mixtures, the floc separatory method on gravity units--electromagnetic vibration table (EVT) and lifting column (LC), have been approached. Satisfactory results can be obtained with a weak shearing. A better metallurgical performance can also be achieved for natural ore slimes through the combined technique. The efficiency is better than that of single gravity separation. Finally, the mechanism has been investigated.

Jan 1, 1990

By David Shatwell

Recent epithermal gold discoveries in Chile and Bolivia provide increasing evidence of a belt of intermittent, epithermal, precious metal mineralization east of the main Andean porphyry copper belt. This relationship may be the result of an easterly decrease in the age of magmatism and erosional levels, in¬crease in depth above the underlying Benioff zone and consequent changes in magma chemistry, or some other unrecognized factor. Examples are: • The Choquelimpie gold-silver mine in Chile and numerous other epithermal prospects (such as La Riviera, Bolivia) in late Tertiary volcanics along the Chile-Bolivia border. These lie east of the belt that contains the Toquepala, Quellaveco and Cuajone porphyries in southern Peru and the Cerro Colorado, Copaquire and Quebrada Blanca porphyries in northern rhila

Jan 1, 1990

By James Matlock

The announcement of a minable reserve of 13.6 Mt (16 million tons) averaging 0.9 g/t (0.027 oz per ton) Au and 2.4 g/t (0.71 oz per ton) Ag for the open pit-heap leach reserve at Red Mountain No. 3 in Ouray County, Colorado, by Cornucopia Resources in November 1985 brings another open pit-heap leach precious metal ore body to the production stage. With about 8.2 Mt (9 million tons) of waste and metallurgical studies showing acceptable recovery rates, low reagent consumption, and good final percentage recovery, Red Mountain is a discovery that will add to the precious metal inventory of the US. Frank Baumgaruler of Denver, CO, recognized the precious metal potential in Red Mountain No. 3 and acquired all of the old claims. James Matlock conducted a field reconnaissance over Red Mountain No. 3 independently of the Baumgartner activities and recognized epithermal alteration and mineralization in the Tertiary volcanics. He recommended acquisition of the ground and was able to obtain rights and drill six core holes for Amoco in 1982. Amoco drilled a further nine core holes in 1983, but then dropped the property. Cyrano Resources examined the data and through its consulting geologist, V.F. Hollister, acquired the rights dropped by Amoco. In 1984 Cyrano began further drilling of the ore zone demonstrated by Amoco but they were then acquired by Cornucopia Resources. Cornucopia completed development of the property and commenced the permitting process in 1986. The property was recognized as a disseminated gold deposit by both Baumgartner and Matlock, and both deserve credit for properly evaluating mineralized outcrop in the Tertiary volcanics. However, Cornucopia recognized the profit potential in the heap leach exploitation of the ores and de- serves credit for completion of premine feasibility studies. The discovery is clearly a geological one, but the premine engineering studies were essential to the conversion of the prospect to a commercial mining enterprise. The deposit lies on the circular bounding fault of the Silverton caldera. Two reprints follow that help understand the geologic setting of the ore controls.

Jan 1, 1990