Search Documents

By R. D. Short

Environmental regulations for noise and air pollution are directly affecting the type of equipment and construction techniques being utilized for pile driving construction using diesel hammers in California and elsewhere. Consequently, the cost of construction is increasing and in some cases, the use of diesel pile hammers has been prohibited. Based on the trend in California and elsewhere in the world, environmental constraints are spreading and becoming more restrictive. The City of Tokyo, Japan, for example has banned the use of diesel hammers. Environmental restrictions on diesel hammers can be satisfied by using modern hammers, clean burning fuels, synthetic lubricants and pre-excavation techniques.

Jan 1, 1989

By J. Wennerstrand

Slender steel piles have found an increased use in Sweden in resent years. These piles are often driven throw soft normally consolidated clay to refusal in till or at the rock surface. In contrast to most other piles the bearing capacity with regard to failure of the shaft is in many cases smaller than the bearing capacity with regard to failure of the soil or rock at the lower end of the pile. Imperfections such as deviations from a straight line of the pile centerline and residual stresses in rolled and welded profiles are important for the capacity of the pile shaft. Even thow the second order moment caused by initial deviations in piles is only half of that in a column with the same slenderness, imperfections can and should be accounted for in much the same way as for columns.

Jan 1, 1989

By R. R. Rollins

Conventional methods of controlling abandoned mine fires include: loading out, inundation, fire barriers, flushing, and surface sealing. This paper describes a proposed fire-control technique utilizing a new explosive fragmentation method. An impervious barrier is created by using explosive energy and strategic emplacement in boreholes drilled from the surface. Blast round design, average fragment size, and impermeability of the fragmentation barrier are discussed. This barrier, created by the blasted floor rock, could also be used to fill in the open space in abandoned mines for subsidence prevention or control.

Jan 1, 1989

By D. A. Bruce

The use of small diameter cast-in-place bored piles is becoming increasingly popular in the United States. Such inserts are used as conventional load bearing piles, and are generally referred to as pin piles. The other major application is for the in situ reinforcement of soil slopes or excavations. The paper reviews the applications, construction, design and performance of inserts of each type.

Jan 1, 1989

By A. F. Banks

"IntroductionThe typical potash processing plant recovers and/ or upgrades from 10% to 20% of its production through the recrystallization process. The feed to the recrystallization section consists of preconcentrated slurries of fine crystal size that cannot be raised to the required product grade by flotation and fine dusts also of low grade and too fine for compaction feed. It produces high grade white potash crystals that can be marketed as a high grade product or blended into the flotation products to raise their grade. In this chapter, a typical leaching (dissolving) and recrystallization operation will be discussed.The crystallization process makes use of the three phase system chemistry of NaCl, KCl, and H,O. The normal potash process operates on a temperature range of 75°F to 95 °F. A three phase slurry feed to the dissolving circuits will be within that range. The potash (KCl) is dissolved by heating the slurry in the presence of sufficient brine to a temperature of 190°F to 200°F. As the slurry is heated, the potash (KCI) dissolves and the salt (NaCI) precipitates. The potash rich brine is then clarified and the salt and other undissolved solids removed by thickening. Clarified brine becomes the crystallizer feed.The hot brine is cooled in evaporative cooling crystallizers. In cooling, the potash precipitates as a high grade white crystal. Crystallization is done in multiple effects to permit energy recovery and control of the process. In a four effect crystallizer the cooling is done by recycling mother liquor counter currently through the first two effect condensors and using brine pond brine for the cooling of the last two.The crystallizer product is removed from the last effect as a slurry at normal process temperature and is fed either to its own centrifuging and drying circuit or blended with the flotation product for centrifuging and drying."

Jan 1, 1989

By G. de B. van Niekerk

This paper briefly outlines some mining technology that is used with success in Australia but is not yet fully utilized in South Africa. The following aspects are discussed: improved rotary-drill bit performance, use of trucks and load haul- dump units underground, long-hole raising, blasting techniques, and the use of butterfly roofbolt plates for support.

Jan 1, 1989

By P. A. Anderson

Innovative solution management is being used at Coeur-Rochester, Inc. to increase bullion production and decrease overall costs. New operating programs call for reduced solution application rates to the heap to increase pregnant stream values at a lower and less costly plant flowrate because silver and gold extractions are equal regardless of leach solution application rate. Solar heating is used in the summer months to increase the core temperature of the heap for use in the winter months thus increasing silver extraction rate. This paper outlines the programs now in effect and the savings incurred because of them.

Jan 1, 1989

By Robert R. Stein

Using an automated drill test fooure, the U.S. Bureau of Mines measured the sound power levels produced by a small, pneumatic, rotary roof drill. A series of tests was conducted to determine (1) the relative effectiveness of several drill muffling schemes and (2) the relationship between drill sound power and pneumatic power supplied to the drill. The influence of rotation rate (i.e., airflow) and feed thrust on the penetration rate of the drill was also noted.

Jan 1, 1989

By J. V. G. Middleton

The paper gives a comprehensive review of the design considerations which determined the choice of the milling plant, a description of the plant and comment on the operating experience to date. Operating experience will include inter alia a description of the mill liners installed with subsequent changes due to wear patterns, the mill inlet sealing arrangement, steel ball addition, mill outlet sump design, cyclone feed pump liner wear patterns and comment on the efficiency of the linear screens for wood chip and tramp removal. Finally a view on future trends in South African milling practice with respect to type and size of plant.

Jan 1, 1989

By M. C. Azar, W. B. Mason, G. L. Anderson

Eminent domain overview Eminent domain is the power of the Government or a municipality to take property for public use without the consent or acceptance of the owner. Typically, the agency taking the prop¬erty will make an offer, hoping the owner will immediately accept and allow work to begin. If a mutual resolution regard¬ing its value cannot be reached, how¬ever, the municipality will institute a condemnation action in court seeking possion of the property. This is when the problems begin. The power of the Government to take the subject property is limited by Federal and state constitu¬tional requirements to pay "just com¬pensation" for the property. The exact nature of an owner's prop¬erty has been the subject of much debate and discussion. It is generally under¬stood, though, that property is consid¬ered to be "every kind of right or inter¬est, capable of being enjoyed and recog¬nized as such, upon which it is practi¬cable to place a money value" (US vs. 53 114 Acres of Land). A taking, for condemnation purposes, is considered to occur whenever there is a substantial interference with the free use and enjoyment of the property. Rarely is the necessity for the taking ever challenged and more rarely is the taking ever successfully challenged. When a taking occurs, it is not only the fee owner who is entitled to compen¬sation. Every person holding an interest in the subject property will be recog¬nized. Thus, all persons who at the time of taking have a compensable interest in the property will be made parties to the case (Swanson vs. US). Minerals, like all other interests in land, are recognized as property rights, giving the owner the power to dispose of them as he or she sees fit. Thus, the only remaining considera¬tion is only "just compensation." Ex¬actly what "just compensation" is has been difficult to define. Generally, it is that amount of money that will "put the person in as good a position as the per¬son would have been in had the taking not occurred." The owner must not be forced to sacrifice or suffer by receiving less than full and fair value for the prop¬erty. Every element that effects the value of the land and that would influence a purchaser must be evaluated. Courts have employed a variety of techniques to determine just compensa¬tion but have generally relied on market value as the standard for measuring compensation to the owner. The deter¬mination of market value is based on sales, income, costs, and use. These factors have been employed in various ways but can be summed up as: -The highest estimated monetary price the property will bring if exposed for sale in the open market with a reason¬able amount of time allowed to find a purchaser who is buying with knowl¬edge of all the uses and purposes to which it is adapted and for which it is capable of being used. • The amount the property would bring if it were offered for sale by one who desired, but was not obliged, to sell, and was bought by one who was willing, but not obliged to buy. • What the property would bring in the hands of a prudent seller, at liberty to fix the time and conditions of sale. • What the property would sell for in negotiations resulting in sale between an owner willing, but not obliged to sell, and a buyer willing, but not obliged to buy. • What the property would be rea¬sonably worth on the market for a cash price, allowing a reasonable time to affect a sale. (Michigan Standard Jury Instructions). Special consideration regarding mar¬ket value is given when the taking is only partial, rather than complete. An example of this partial taking is when a state highway cuts across the northern half of a parcel of property, leaving the rest behind for the owner. A variety of problems can be immediately seen. In a partial taking, the owner is permitted to recover not only for the property taken, but also for any loss in the value of the remaining property. The measure of compensation for partial taking purposes is generally the difference between the market value of the entire parcel before the taking, and the market value of what is left of the parcel after the taking (Michigan Stan¬dard Jury Instructions). Determining the partial taking value for mineral bear¬ing lands is the difficult issue.

Jan 1, 1989

By Jorgensen D. K.

The Bullfrog and Montgomery-Shoshone deposits, outside Beatty, Nevada, have a combined drill-indicated reserve of 17.4 M tons of ore with an average grade of 0.103 oz/t Au and 0.240 oz/t Ag. The deposits occur in Miocene volcanic rocks which underwent large-scale movement within a detachment-faulted terrane. The principal host to gold mineralization is a strongly welded rhyolitic tuff which experienced brittle deformation during plate movement. Open-space fractures and breccia were filled with quartz, calcite, and adularia accompanied by lesser pyrite, gold, and acanthite. Gold occurs as micron-sized particles within and adjacent to the low-angle fault and along associated listric-normal and tear faults.

Jan 1, 1989

By J. D. Findlay

The demands on development in London in recent years has led to the increasing use of top down construction methods in which there is a requirement to place steel columns to high tolerances into large diameter bored piles with deep cut-offs. A number of different proposals for the sequence of construction are being suggested. The tolerances requires for the steel columns are becoming increasingly stringent. This review examines a number of basic construction proposals and comments on the problems and solutions used by foundation contractors to provide the required foundations.

Jan 1, 1989

By J. Hoover

"IntroductionThis chapter will discuss the operational and maintenance aspects of a heavy media cyclone circuits as applied to coal processing and using magnetite as the media. It deals with heavy media bath separators in terms of types of media, equipment, circuits, media recovery, maintenance, and product handling. It will detail heavy media cyclone operation and supplement the previously described topics.The heavy media cyclone was first developed in the Netherlands by the Dutch State Mines in 1945. A cyclone plant was not built in North America until 1961. Traditionally, heavy media cyclones have been used to treat size fractions between 1lz in. (12 .6 mm) and 35 mesh (0.5 mm). High maintenance related to heavy media bath separators has recently prompted some plants to crush all raw coal to minus 2 in. for treatment in heavy media cyclones.The heavy media bath separators utilize only the force of gravity to make the separation between heavy and light particles. This requires lengthy retention time which can lower capacity and also is inefficient for finer particles. A heavy media cyclone utilizes centrifugal forces which are 20 to 200 times greater than the force of gravity. This means the separation between coal and the impurities occurs very quickly, therefore a low retention time is required allowing cyclones to have high tonnage capacities. Also these greater forces allow better separation for the finer particle sizes.Heavy media cyclones are now widely used to produce both metallurgical and thermal coal. Work is in progress to reduce magnetite consumption, extend wear life, increase tonnage capacity, improve separation efficiency and automatically control these cyclone circuits."

Jan 1, 1989

By Bruce Vandenberg, R F. Chiappetta

"The High Speed 2D Analysis program allows the user to bring in data from several different sources. Of course, keyboard entry is included as a source. Other data is inputted through the serial port (X-2321 of the PC. Two types of data are transferred via the serial port. The first is the tablet digitizer data. The three types supported presently are the GTCO, tablet digitizers. and the Calcomp 2500 and 9100 series To transfer digitized data turn on the selected digitizer and place the cursor on the tablet. Enter the High Speed pmg.ram and select from the Input Program menu the Digitize Inputs(20) option and follow the instructions. TO exit the session, either a keyboard entry or a cursor button is pressed. The second type of serial port input Is from the collectors of the listed survey systems. Typically a file transfer program will be used to send the data from the collector to the PC. This topic will not be addressed at this time."

Jan 1, 1989

By F. F. Aplan, J. A. Gutierrez-Rodriguez

"Contact-angle and flotation techniques were used to evaluate the influence of oxygen - both that inherent in the coal and that introduced by ambient temperature, aqueous oxidation - on a wide range of coal ranks. Oxidation was found to decrease the hydrophobicity and floatability of coal; with the effect being minor for coals of high rank but becoming increasingly important as the rank of coal is reduced. As an approximation, oxidation makes a coal behave as if it were one of lower rank. Frother only flotation' of coal· correlates with the captive-bubble contact angle whereas when oil is used as a collector, the flotation appears to follow the pattern shown by the water sessile drop on a fresh, un-reagentized coal surface. Coal recovery lost through oxidation may often be recovered by use of a variety of collectors, of which No. 2 foe! oil is among the best of those reagents tested. A simple alkali-extraction test may be used to estimate the influence of oxidation on coal preparation processes and use.INTRODUCTIONThe hydrophobicity of coal is not only a function of its rank but also of the extent of oxidation of the coal during and subsequent to its formation. Weathering and oxidation processes may proceed in-situ for coal deposits that outcrop near the earth's surface, or the oxidation of the coal particles may occur during mining, stockpiling or processing. Such oxidation, whether it affects the bulk-coal sample or on1y a thin outer layer on the coal surface, can dramatically influence the wettability of the particle and hence such processes as flotation, filtration, flocculation and dispersion.Many of the studies made on the oxidation of coals ·were designed to study its effect on flotation, coking or pyrolysis. The. present study 'is directed exclusively toward the effect of oxidation on the hydrophobicity and floatability of the coal. One of the first studies of the effect of oxidation on coal flotation was that of Sun [l] who found that as oxidation proceeds, coal becomes progressively more hydrophilic. Low-temperature oxidation (100-150°C for 250 h) generally lowered the coal floatability with an oily collector only slightly, but more extensive oxidation (200- 3500 C for 250 h) reduced coal floatability seriously. Sun also found that cationic amines were effective collectors for the oxidized coal which infers that oxidation makes the coal more negative in solution. He attributed the loss of floatability to be due to the accumulation of water-insoluble oxidation products at the coal surface. Gayle et al. [2] found that oxidation adversely affected coal flotation when an aliphatic-alcohol frother was used, though a small amount of oxidation appeared to improve the floatability of some coals using a kerosene-pine oil, collector-frother mixture in pilot-plant testing. Prolonged oxidation adversely affected the flotation recovery of the coals tested, the effect being more pronounced when an alcoholic-type frother only was used. They also noted that the reduction in floatability of lower rank bituminous coals was more affected by oxidation than was that of higher rank bituminous coals."

Jan 1, 1989

Coal is of tremendous importance for the Czechoslovak econ- omy. The current annual primary energy demand being about 109 million tons of standard fuel (1 ton of standard fuel - 7,000 coal = 29,308 GJ), coal satisfies almost two thirds of our fuel consumption. If compared with the distribution of resources in the world's fuel and energy pattern, the situation in Czechos- lovakia is significantly different, as shown in Fig. I. One of the causes behind the difference is that the Czechoslo- vak oil and natural gas reserves and, hence, their production are insignificant, so that it is necessary to import them. Brown coal will continue to play an important role as a prin- cipal domestic source of primary energy even in the future. While the share of nuclear power is increasing, brown coal represents strategic reserves in the fuel and energy balance.

Jan 1, 1989

By P. G. Mason

The Getchell property was mined for oxidized gold ore by underground and open pit methods from 1936 to 194.5, by which time known oxide ores were mined out. From 1945 until 1967 sulfide ores were mined and roasted to improve gold recovery with varying degrees of success. In J 983 FRM Minerals, Inc. purchased the property. Since then they have carried out extensive geological exploration to define the size and character of the orebody. The sulfide ore is refractory to direct cyanidation, thus considerable metallurgical testing has been necessary to develop a suitable, cost effective process for its treatment. Wright Engineercs Limited have designed and engineered a gold extraction plant, which incorporates pressure oxidation to liberate the gold and? is scheduled to be commissioned early in 1989.

Jan 1, 1989

By N. S. Dalal, W. Irr, X. Shi, V. Vallyathan

"Inhalation of crystalline silica is associated with a biphasic biologic response of acute cell injury and chronic pulmonary fibrosis. Dust induced cell membrane injury leading to the release of lysosomal enzymes and cell death has been implicated as the initial important biologic event triggering the fibrosis. However, it ls also possible other biologic reactions could alternatively, or in addition to these enzyme related cytotoxicity reactions, alter the normal functioning of cells. It is well known that phagocytic activation results in the production of oxygen radicals which are highly cytotoxic to cells. In healthy - lung, protection against the toxic effects of the normal balanced ·biologic reactions are provided by a number of defen1e systems including antioxidants. In disease or condition of overproduction of oxygen radicals, biochemical protection may be overwhelmed with resultant cellular injury.Our recent observations have shown that reactive oxygen radicals (ROR) are generated during grinding of crystalline silica. We hypothesized that these newly generated RORs may cause cell injury, lipid peroxidation, or even damage to macromolecules such as DHA. Biochemical aberrations caused by the inhalation of crystalline silica with ROR at occupational settings might overwhelm cellular and antioxidant defense systems of the lung leading to injury and subsequent fibrosis.To test this hypothesis, we have investigated the generation and decay of ROR produced by crystalline silica using electron spin resonance (ESR) and investigated its toxicity with conventional biologic tests at various time intervals after grinding. We also studied the decay of these newly generated RORs in buffer and the effect of antioxidants and scavengers in the abolition of cellular damages."

Jan 1, 1989

By W. G. Pariseau

A crown pillar cave occurred at the Ropes Mine in December, 1987, that resulted in closure of the mine. Production was resumed soon afterwards with the formulation of a rock mechanics plan designed to address several issues of safety and stability. The plan proved to be successful and shows what can be accomplished in the realm of applied rock mechanics where a cooperative atmosphere exists.

Jan 1, 1989

By W. J. Mcgaughey

A crosshole seismic imaging (tomography) experiment has been carried out in an underground mine in order to delineate waste rock within a massive sulphide ore body. Data comprising 1526 travel time measurements were inverted to yield a compressional wave speed image consistent with, and adding to, knowledge of the extent of the waste inclusions. An effective method of resolving travel time discrepancies measured on reversed ray paths is presented.

Jan 1, 1989