Search Documents

By D. G. Mason

During the design of copper refinery tankhouses, there is a need to develop mass balance calculations for many process components, so that optimum physical plant configuration is achieved. Each mass balance is complex, possibly with over 120 interactive variables as basic input data. Recent developments in tankhouse design (e.g. permanent cathodes) have greatly increased the design options available for any project, multiplying even further the requirement for calculations. In the past these calculations were tedious and susceptible to human error. A comprehensive computer program can now simplify the task of the process metallurgist, enabling more sophisticated and sensitive plant designs to be produced. The paper describes the successful development of a flexible mass balance program that originallly was used in a feasibility study which had to be completed within a short time schedule. The program has been further developed and used for design and energy calculations; it can be usefully applied to existing plants to assess the impact of variations in operating parameters. The software takes account of staged liberation, electrolyte purification bleed and generates a reliable process inventory listing: it can also cope with stripper starting sheet options and disparate commercial circuits.

Jan 1, 1987

By Alan G. Mayton

The Bureau of Mines conducted a study to (1) determine from laboratory tests the feasibility of a photographic method for determining reflec-tances that may be applied to measuring in-mine mineral reflectances and (2) formulate a procedure for collecting and analyzing the data. The method uses a 35-mm camera with automatic flash and a gray-scale re-flectance standard to collect on film the reflectivity data in under-ground mineral mines. After the film is processed, the data on the photographic prints are analyzed in the laboratory with a photometer. Test results show the photographic method can provide values of reflec-tance to within ±5 pet of full scale (full scale = 100 pet). The method's usefulness for determining reflectivity values, within similar limits of absolute percent error at the lower end of the scale, however, has not been completely resolved by the study and consequently warrants further investigation. The method offers an acceptable means for collecting and analyzing reflectivity data for reflectivities at the higher end of the scale, i.e., 50 pet or above; it should be used with caution when reflectivity values are below 50 pet. Four films were evaluated; all gave relatively satisfactory results.

Jan 1, 1987

By J. A. Meech, C. A. Harris

"The application of control theory in mineral processing is more difficult than in other industries because of the complex nature of the unit processes involved and because of problems with accurate on stream measurement of process variables. Conventional control is based on proportional, integral and derivative functions of a continuously measured error term. Computer control can enhance these actions by incorporating logical routines to switch from one relationship to another. The success of this logical approach depends on our understanding of the process dynamics and the stability of the process and model under all conditions. Typically the model does not apply at all times in mineral processing because of frequent and unmeasurable changes in the ore parameters.Recent advances in the theory of fuzzy sets have led to the application of this science to process control. Fuzzy Logic can be used to develop heuristic or rule-of-thumb controllers with the strategy based on the actual operating practice of experienced plant operators. Control action has increased flexibility through the adaptation of human reasoning. Acceptance of the control system by operating personnel is significantly higher because of their participation in its formulation. The requirement of an exact model is not essential.A heuristic controller has been designed and tested with a computer simulation model of a secondary crushing plant. The results of this study are discussed and future applications of this control technique to other mineral processes are suggested. IntroductionThe application of control theory in mineral processing is more difficult than in other industries because of the complex nature of the unit processes involved. Mineral processes typically are characterized by non-linear relationships between input and output variables. Many of these variables cannot be monitored accurately on-stream and so long time lags on the measurement loop are features of the system. The processes, themselves, often have long time-varying responses while the process loads fluctuate significantly on a short-term basis.Attempts to control these processes have led to the formulation of mathematical models to describe each unit activity. Adaptive techniques have also been tried to compensate and account for process changes and vageries. These approaches are mathematically rigorous so that their complexity and precision limit their usefulness when applied to ""vague"" processes."

Jan 1, 1987

By M. K. Gangal, E. D. Dainty

The paper describes the capabilities of a micro-computer-based real time data acquisition system for monitoring and control of mine environments. Applications of such a system for monitoring the ventilation and air quality of a mine is outlined. The paper discusses the results of running a monitoring system with various environmental sensors in a simulated mine environment. The sensors used in this study are: carbon monoxide (CO), carbon dioxide (C02), nitric oxide (NO), nitrogen dioxide (NO2), sulphur dioxide (SO2 ), methane (CH4 ), air flow, absolute pressure, temperature and relative humidity. A performance evaluation of the monitoring system and sensors is presented.

Jan 1, 1987

By J. Mitchell Linne

In 1985, at the request of Bureau of Land Management, the U.S. Bureau of Mines studied a 54,480-acre portion of the 93,205-acre Dry Valley Rim Wilderness Study Area (CA-020-615), in order to evaluate its identified resources. The area studied is in Washoe County, NV, and Lassen County, CA, about 35 miles east of Susanville, CA. No metallic resources were identified. The Red Rock and Willow Springs areas contain 85 million tons of altered basalt with zeolite amygdules. This material, averaging more than 50 percent chabazite, constitutes a subeconomic zeolite resource. This zeolite-bearing material would require beneficiation to upgrade it for higher value uses. Natural zeolites have a small market in the United States, which is presently supplied by other higher grade material. There is low probability that these resources will be mined in the foreseeable future. The Capricorn claims, adjacent to the study area, are on alluvial sediments containing more than 30 percent montmorillonoid clays. The material is not usable as pozzolan and was not tested for other uses such as absorbency, oil clarification, or insecticide carrier. The term pozzolan refers to a number of siliceous materials which are combined with portland cement to enhance the physical properties of the resultant concrete. The area is remote from market and contains low value material. It is improbable that this occurrence will be mined in the foreseeable future.

Jan 1, 1987

By J. C. Edwards

The Bureau of Mines developed a mathematical model for analysis of the impact of scrubber bed length, porosity, and gas flow rate on the absorption of C02 in a breathing apparatus. The model accounts for the decrease in available absorbent through chemical conversion. The pre-dicted efflux of C02 from a canister containing LiOR compared favorably with measured values reported elsewhere. It was determined from a com-putational study that the time for breakthrough of C02 at a prescribed level is nearly directly proportional to bed length and inversely pro-portional to gas flow and porosity.

Jan 1, 1987

By Claus Becker

The Mixshield is a tunnelling machine for water bearing soft soils. Developed on the basis of the Hydroshield, it extents the application of this machine to cohesive soils. The design of the drum-type machine allows three different applications 1. As shield with liquid supported face and hydraulical mucking 2. As Compressed-Air-Shield 3. As Earth pressure balanced shield. The Mixshield is employed on three big contracts 1. a 6.3 km ring tunnel in Hamburg, outer diameter 5.95 m, with a new developed segmented concrete lining 2. a 1.9 km pipe-jack job near Cologne, o.d. 3.6 m 3. Metro Lot 3 in Lille/France, o.d. 7.7 m, 3.2 km long with segmented concrete lining and a most sophisticated separation-plant The site experiences will be reported.

Jan 1, 1987

By T. P. Meloy

Media mills operate by having energy transferred to the media which in turn grinds the feed material in a packed bed. Regardless of the mill type, the media energy density per unit surface area is constant. Since for optimum grinding conditions, both peak pressures and particle number of the bed depth are constant, the frequency of energy input is inversely proportional to feed size. As the particle size decreases the voles energy density increases linearly necessitating cooling in stirred mills. Grinding finer particles therefore, requires moving from rotary to vibratory mills, and the finest, the stirred mills.

Jan 1, 1987

About 74% of global seismic energy release occurs in the Circum-Pacific zone. Worldwide, about 71% of seismic energy release is in the form of shallow earthquakes, 27% as intermediate, and 2% as deep earthquakes. Seismic energy release is variable in time and has been shown to correlate with the amplitude of the Chandler wobble. It was high during the period 1949 to 1967, and is now at a rather low level, with the latest earthquake over M = 8.0 having taken place in Indonesia in 1971. The average worldwide recurrence rate for the expected largest magnitude earthquake (M "9.5) has been estimated as several tens of years, in marked contrast to the several tens of thousands to hundreds of thousands of years separating the largest volcanic eruptions. Geological studies are needed to establish reliable mean intervals between large earthquakes, and to detect the e;:istence of long-term fluctuations in the ste of occurrence. Seismic gaps have proved seful in static forecasting of large earthquakes, by identifying places where closer study of the variation with time of seismicity, deformation, and other parameters, may lead to the dynamic p_ediction of time, place and magnitude of earthquakes. The model of stress concentration at asperities explains the main features of seismicity in the Circum-Pacific. Slow earthquakes have been detected instrumentally, notably an event immediately preceding the 22 May 1960 Chile earthquake, the largest this century. It seems likely that this type of deformation may explain both instrumentally detected and macroscopically observed pre-seismic deformation, as well as unusual animal behaviour reported before some earthquakes. Seismic and volcanic events are interdependent, with large earthquakes commonly triggering eruptions. Melting of rock and intrusion of magma is likely to accompany many earthquakes.

Jan 1, 1987

By R. G. Horvath

In the Hamilton area, and in many other areas of Ontario and around the world, large diameter drilled pier (caisson) foundations are frequently selected as the most appropriate foundation system for heavily loaded structures. Locally, these drilled piers are typically founded in competent glacial till or in the underlying shale bedrock depending on the anticipated design loads. Drilled pier foundations socketed into shale bedrock were selected for the Hamilton General Hospital Addition. The structural loads applied to socketed pier foundations are supported through shaft resistance, which is the shearing resistance developed along the vertical pier-rock interface, and by end-bearing resistance. The factors which control the load-displacement-time behaviour of socketed pier foundations are the strength and deformation characteristics of: a) the concrete pier, b) the rock mass, and c) the interface between the concrete pier and the rock.

Jan 1, 1987

By P. Piga, O. Sammarco

There is a markedly increasing tendency to design deeper and deeper mines, to use larger amounts of explosive per round, to increase the advance rate of the excavations and so the natural ventilation tends to be more intense in the new mines. For this reason, the mines that make use of powerful mechanical ventilation should also take into account such factors as natural ventilation pressures, especially in the case of mines excavated in high-temperature rocks for which natural ventilation is particularly intense. The results of the studies reported here refer to a very hot mine excavated in an area with a high geothermal flow (the Boccheggiano - Campiano mine, southern Tuscany). At various external temperatures, experimental measurements and analyses have been made of the trend of the thermodynamic characteristics of the ventilation air and of the trends of the air/rock heat exchange along the downcast shaft and along the upcast shaft. These data were then used to work out approximate values of the corresponding natural ventilation pressures. After having identified the most conspicuous variations of the thermodynamic parameters of the ventilation air and the factors causing them, an assessment was made of the repercussions they have on the air flow rates and, above all, on the climatic conditions of the underground excavation sites. The natural ventilation pressures were found not to be constant in time; indeed they change continously and it is difficult to predict the changes. Moreover, it was found that their influence on the ventilation of a section of the mine network is greater if the effect of mechanical ventilation on that section is weaker. In the mine section where the measurements were carried out, some portions were found where the ventilation could become insufficient as a result of the effects of natural ventilation pressures. Finally, some guidelines to be followed in designing hot mines have been put forward which ensure efficient ventilation throughout the network at times with the aid of the natural ventilation pressures, which in certain circumstances may reach very high values in mines of this type.

Jan 1, 1987

By Jim Peregoy

INTRODUCTION Frontier-Kemper Constructors, Inc. is an Evansville, Indiana based heavy construction contractor engaged in projects for both the public and private sectors of the underground construction industry. Construction activities range from conventional shaft, slope, tunnel and chamber excavation through state-of-the-art mechanical excavation, ground freezing, standard support and structural concrete operations. Conventional excavation and concreting equipment, as well as raise boring machines, road headers, tunnel boring machines, and freeze plants are owned, operated, maintained and modified "in-house" to suit the needs of individual projects. The balance of this paper wilt present a general overview of the Frontier-Kemper planning and construction operations on the recently completed Phase II of the U.S. Army Corps of Engineers, John Day Dam, Juvenile Fish Bypass Project. General Project History The U.S. Army Corps of Engineers is responsible for designing, constructing and maintaining various navigation and impoundment structures on the nation's inland waterways. Maintenance involves both the work required to maintain the structure in fully-operable condition and the ongoing work required to maintain a positive impact on the environment. John Day Dam is located on the Columbia River approximately 95 km (60 miles) upstream of The Dalles, Oregon. It was constructed to: provide electric power to the Pacific Northwest; provide Locking for up-and-downstream bound commercial and private watercraft; act as a water impoundment structure to control flooding conditions; and to provide a source of irrigation water

Jan 1, 1987

To quickly and more reliably measure the alignment and deflection of mine guides used to run skips and cages into a mine shaft. The Problem Conventional mine guide alignment measuring systems require the use of a plumb bob and tape measure. This method is not only laborious, but it is time consuming as well. Approach Aware of the drawbacks of the current measuring method, the Bureau of Mines designed a self-contained instrument system that can accurately perform vertical guide alignment and deflection measurements by remote control. How It Works The Bureau-developed instrumentation system, called the Guide Alignment Measuring System (GAMS), is based on conventional mechanical electronics using inclinometers and displacement transducers. The instrumentation system is attached to an operating skip or cage where it functions as a completely self-contained measurement system, operating in conjunction with nor-mal travel of the skip or cage. An on-board tape recorder or a mini-computer with memory can be used to record all telemetry.

Jan 1, 1987

By Keith L. Harris

Recent data indicate a marginal decline in overall growth in world economic output from 3.1% in 1985 to 2.9% in 1986 (table 1),2, 3 Many nations experienced slower economic growth because of the huge trade imbalances existing between the United [ ] States and Japan and the Federal Republic of Germany, the U.S. budget deficit, and the growing Third World debt. Some developing nations, however, experienced booming growth. Declining prices for energy and nonenergy commodities and the fall of the dollar against the currencies of major industrial countries benefited several developing countries--energy importers and exporters of manufactured goods with currencies tied to the U.S. dollar, which were able to expand markets in the industrialized nations. The drop in commodity prices increased demand in industrial countries and depressed it in developing countries. Lower demand in the developing countries contributed to a decline in the real net exports from industrial countries. As a result, output growth in industrial countries declined from 3.0% in 1985 to 2.4% in 1986, despite growing internal demand, Average output growth of developing countries increased from 3.296 to 3.596 during the same period, however, primarily because of the low prices of their products and the strength of demand in industrial countries for those products. Developed country output growth was extremely uneven, however. For example, the economic output of nonfuel exporters grew 5.4% in 1986, while that of fuel exporters dropped 0.7%.

Jan 1, 1987

By J. O. Guthrie

Newmont has delineated a 600,000+ ounce gold reserve in the Cargo Muchacho Mountains. This is a desert range underlain by Proterozoic(?) Tumco Formation (gneiss) intruded by Jurassic granitic plutons, and cut by low angle shears of the late Cretaceous Chocolate Mountain Thrust event. Gold, associated with pyrite, quartz veinlets, and propylitic alteration, is emplaced along low angle shears. The mineralizing system, enriched in tungsten, copper, zinc and arsenic, was active during Eocene time. Gold reserves are found in eleven areas as moderate to high tenor deposits that may be mined by open pit and underground techniques. Eastmaque Gold Mines Ltd. is developing the deposit.

Jan 1, 1987

By Alex C. Smith

This report describes laboratory studies conducted by the Bureau of Mines on the spontaneous combustion of U.S. coals. Approximately 11 pet of U.S. underground coal mine fires are attributed to spontaneous combustion. The relative self-heating tendencies of 24 coal samples were evaluated in an adiabatic heating oven. Minimum self-heating temperatures (SHT's) in the oven ranged from 350 C for a lignite and high-volatile C bituminous (hvCb) coal, to 1350 C for two low-volatile bituminous (lvb) coals. An empirical expression was determined predicting a bituminous coal's minimum SHT in the adiabatic oven based on the coal's dry ash-free oxygen content. Several factors that can affect the self-heating process were also evaluated. The self-~eating tendency of a coal increased when the coal was dried and exposed to humidified air, and was dependent on the particle size and oxygen concentration of the air. A new moderate-scale apparatus is described, in which the self-heating tendencies of larger coal samples, 3 kg, can be evaluated. The minimum SHT's of two coals were determined and the results were in good agreement with those found in the adiabatic oven. Finally, results of a test in the moderate-scale apparatus indicated a strong dependence of the self-heating rate of a low rank coal on the moisture content of the air.

Jan 1, 1987

By S. L. Bessinger

In the design and specification of a ventilation system for an underground mine, it is necessary to make reasonably accurate estimates of the pressure losses in the various airways of the mine. These estimates can be made with little difficulty for open airways with simple geometric cross-sections, such as those cut by continuous miners or tunnel-boring machines. The situation is much different on a longwall face, where the airway's complex geometric cross-section and the presence in the airway of obstructing equipment having a variety of shapes make it difficult, if not impossible, to estimate pressure loss using traditional methods of calculation. Headlosses in mine entries are calculated using Atkinson's Equation (1). [H = (English) H = (SI) (1)] where H = pressure ,loss, in. of H20 (Pa) K = friction factor, lbf min2/ft"4(Kg/m3) P = perimeter, ft. (m) L = airway length, ft (m) Q = airflow quantity, ft3/min (m3/sec) A = flow cross sectional area, ft2 (m2)

Jan 1, 1987

Grade control plays an essential role in the good running of a mine. The factors at play are many, starting from a good analysis of the geology and a correct sampling procedure. Once this is achieved (and it is an essential prerequisite), the problem is to adequately define what is ore and what is waste. This paper tries to show, through a small example, how simple geostatistical techniques (variography, and moving average or kriging), can help in accurately defining these limits in a geologically homogeneous zone, thus allowing optimal use of the available information.

Jan 1, 1987

By Michael J. Martinson, John R. Larsen, J. Warren Andrews

Measurements reported in the paper were recorded in an active Green River, Wyoming, trona mine, partly as a teaching exercise and partly to provide the mine in question with additional input data for its ventilation network program. Measurements were made: - in representative three-entry intake airways in room and pillar sub-mains; - between the lower portion of a vertical down-cast hoisting shaft and the start of an intake airway system established in a room and pillar main; - in a representative downcast section of a divided vertical shaft, and of the collar entrance loss at the top of the same compartment. Pressure differences were measured with manometers and trailing hoses, air flowrates with calibrated anemometers, and barometric pressures and wet-and dry-bulb temperatures were recorded for density determinations. Where possible, results are quoted as Atkinson friction factors, and relevant measurements are recorded in some detail to show the magnitude of fluctuations in observed pressure differences.

Jan 1, 1987

Jan 1, 1987