Search Documents

By Robert J. Evans

The monorail bridge conveyor (MBC) is a prototype continuous face haulage system that was surface tested and evaluated by the Bureau of Mines. The MBC consists of a series of cascading belt bridge conveyors suspended from roof-supported monorail track. Tests were conducted to determine MBC haulage capability, maneuverability, power consumption, and reliability using rigid and chain-suspended monorail track installations. Subsequent modifications to improve operation and reliability made during surface testing are described. Mining plans were devised to show potential MBC installations for room-and-pillar, longwall development, and shortwall mining sections. Compatibility tests were conducted with the Bureau's prototype hopper-feeder, to provide additional surge capacity and lump-breaking capability. Results from the surface test program, along with modifications to improve system operation and reliability, indicate that the MBC has the potential to perform success- fully in an in-mine trial.

Jan 1, 1987

By Drew GJ

Smelting is a process in which heat is applied to ores to produce metals. Impurities are removed by segregation in the slag, or converted to gases or sublimates and discharged up the flues. Mate- rials delivered into the smelter have generally been previously concentrated or processed at the mine, and the size of their particles, and also their chem- ical composition, greatly affect the smelting proc- ess. Some impurities are more difficult to remove than others, and are more objectionable in the finished product. The first metal mine in Australia was opened near Glen Osmond in South Australia in 1841, for silver-lead ore. It was followed by the Kapunda Mine for copper in 1844 and by the very signifi- cant Burra Mine, also for copper, in 1845 (Figure 1). A major part of their ores could not be exported profitably for smelting in England and Wales where the large smelters were then located. In addition to treating ores from Cornwall these also smelted ores from recently opened mines in Cuba, Chile, and Mexico. The Welsh smelting process (Figure 2) was developed over a period of years to utilise Welsh coal to treat copper ores particularly from Corn- wall. The first step consisted of a calcination to remove sufficient sulphur from sulphide ores so that subsequent melting operations would produce copper matte, a copper-iron-sulphide which melted at about 1050¦C. Subsequently refined to white metal with the addition of carbonate and oxide ores when these were available, and often through an intermediate step of blue metal, this matte was finally oxidised to pure copper, or as pure as it could be made in those days. The movement of metal towards greater purity was matched by a reverse flow of slag, carrying reducing quantities of copper, so that the slag rejected from the first melting process carried the minimum quantity of copper. Chemical analysis was virtually unknown. Materials were assayed in the laboratory by a small scale smelting process, and the purity of the final refined copper was judged b} the ease with Mhich it could be hammered into thin sheets.

Jan 1, 1987

By Gary J. Fletcher

Mining and processing activities which are proposed on private land, state leases, or unpatented mining claims are governed by numerous local, state, and federal laws which identify the procedures and conditions which must be met before resources can be developed. The respective government agencies responsible for the administration and enforcement of these laws have promulgated supporting regulations and guidelines, and have implemented certain permit and approval processes to ensure compliance. Each exploration project has a unique environ- mental setting and location which further dictates the types of air, water, hazardous waste, and wildlife laws and regulations which must be complied with before development commences. The environmental planning process should be the first step in the evaluation of existing company properties and the potential acquisition of other mineral properties. However. many company don't consider the environmental requirements for a project until the decision is made to develop the property for mining and processing. If a mining company wants to expedite the environmental planning process, it must first develop an in-house process for evaluating the project and determining the environmental approval procedures in the state where the project is located. The first stage of environmental planning involves general information which can set the overall company philosophy for development of projects.

Jan 1, 1987

By M. J. Ferrante

Relative enthalpies of cuprous iodide (CuI) were measured at the Bureau of Mines to provide thermodynamic data for the advancement of min-eral technology. Enthalpy measurements between 298.15 and 1,396.3 K were made with a copper-block drop calorimeter. The temperatures of transition were measured by differential scanning calorimetry (DSC). Reversible transitions were determined at 643 K with a standard enthalpy of transition [(6Htr)] = 0.74 kca1/mol, at 679 K with a [6Htr = 0.65 kca1/mo1, and at 868 K] with a standard enthalpy of fusion [(6H~) = 1.895 kca1/mol.] Tabulated values are listed at selected temperature increments from 298.15 to 1,600 K for the standard relative enthalpy (HO -H298), heat capacity (CpO), entropy (SO), and Gibbs energy function [-(Go -H298)!T]. The enthalpy data are also given in the form of equations and combined with thermodynamic data from other investigations to derive values of standard entha1pies of formation [(~HfO)], Gibbs energies of formation [(6GfO)], and logarithms of the equilibrium constants of formation (log Kf).

Jan 1, 1987

By Stone. Jon P.

INTRODUCTION Countries that are currently developing their mineral potential have unique information systems requirements to support these activities. The mining laws usually grant the State considerable authority over the process. In many instances, the mining laws give a government agency the responsibility for granting and controlling exploration permits and development concessions. This is the case in Costa Rica. The Direcion of Geologia, Minas, y Hidrocarburos (DGMH) of the Ministerio de Industria, Energia y Minas (MIEM) is responsible for the management and operation of the National Mining Register. This paper describes the results of two studies of the information system requirements to support the National Mining Registry as well as those supporting some of the other function of the DGMH. The first of the studies reviewed the situation before the installation of computer equipment. The second study evaluated the installed systems. BACKGROUND Historical Perspective Mining in Costa Rica is at present a relatively minor part of the economy. It consists primarily of industrial minerals and gold production. Gold production is largely by small-scale miners and may be more substantial than reported. There is considerable interest on the part of the Government in both having a better understanding of the existing mining industry and promoting future development. Mining law was first provided by the Ordinanza de Mineral (of 1830). This was replaced by the first Mining Code of 1953. Apparently, one of the first problems caused by the 1953 law was the granting of concessions which were not worked. A 1968 agreement with ALCOA also resulted in political conflict. The Government worked on a new Mining Code for many years and in 1982 the current Mining Code was enacted. Draft implementing regulations were prepared in April 1984. Mining Code of 1982 The Mining Code of 1982 addresses most aspects of mining in Costa Rica including the declaration that all mineral resources are to be the property of the State. The State may grant exploration permits and exploitation permits. The exploitation of hydrocarbons, radioactive minerals and certain water resources was reserved to the state. The DGMH was given authority to settle placer claim disputes, maintain a registry of exploration permits, and exploitation concessions. and generally supervise mining activity. Towards this, the Mining Code of 1982 includes rather detailed requirements for the processing of application for permits and concessions. Mining Code Application Requirements The following briefly describes the requirements to give the reader a feeling for the complexity of the process. Currently, over 1,000 active applications, exploration permits and exploitation concessions are being monitored under the process. The number remains relatively consistent in that the number of new applications is usually about the same as the applications that are put aside. The time and date of the filing must be certified by the DGMH. The application must include all the information specified in the Mining Code. If incomplete, DGMH must notify the applicant of the deficiencies or omissions and direct that the applicant correct the deficiencies or omissions within 8 business days (a single 30 business-day extension is allowable). If the applicant does not respond as directed, the application is deemed as not having been filed and the pertinent information is placed in the files. The DGMH must reject the application outright and direct it be placed in the files in the following cases: (a). If the new application covers the area of a previous permit or concession, either being processed or already granted.

Jan 1, 1987

By Jean-Marc Simard, Vincent Jourdain, Denis W. Roy

"Seven lithologic units, informally characterized, were recognized in the vicinity of the Montauban orebody. The first five lie in stratigraphic order. From structural bottom to structural top these are: (1) grey composite gneiss; (2) dark grey quartz-biotite gneiss; (3) quartz-biotite-garnet gneiss hosting several calcareous, aluminous and magnesian members and gold mineralization; (4) light grey quartz-muscovite-(sericite)-biotite gneiss; and (5) metabasafts. The last two intrude the sequence: (6) amphibolite dykes and (7) pegmatite veins. The orebody lies on the inverted limb of an overturned synform verging to the west with the metabasafts marking the core of the fold. As the foliation is folded, this fold is attributed to deformation ""D2""; deformation ""DI"" being responsible for the formation of the foliation. A late brittle deformation developed shear zones with probable strike-slip motions. The refined stratigraphy and the identification of the structural position of the orebody provide new tools for regional interpretation and prospecting.RESUMESept unités lithologiques ont été définies informeffement à proximité du gisement de Montauban. Les cinq premieres reposent en ordre stratigraphique; ce sont de la base au sommet structural: (1) le ""gneiss mixte gris""; (2) le gneiss gris forcé à quartz biotite; (3) le gneiss a quartz-biotite-grenat comprenant plusieurs membres calcareux, alumineux et magnésiens ainsi que la minéralisation aurifère; (4) le gneiss gris clair à quartz muscovite- Isericitel-biotite; et (5) les métabasaltes. Les deux autres unites sont intrusives dans la sequence: (6) les dykes d ‘amphibolite et (7) les veines de pegmatite. Le gisement se sitlie sur le flanc inverse d'un synforme déverse vers I' ouest dont les métabasaltes occuperaient le cœur. Comm e la foliation est plissée, ce pli est considère appartenir d la deformation ""D2""; la deformat ion ""DI"" etant responsable de la formation de lafoliation. Une deformation cassante tardive se traduit par des zones de cisaillement, d rejet apparemment directionnel. Cette stratigraphie plus précisé et l'indentification de la position structurale du gisement fournissent de nouveaux omits de prospection et d'interprétation regionalé."

Jan 1, 1987

By R. S. Das, A. K. Sinha

Modern mine ventilation systems have grown rapidly in recent years both in terms of complexity and value for human health and safety. Although computer models are now available to help the design and operation of mine ventilation systems, considerable differences often exist between the computer-based predictions and practical results. Research conducted to compare computer results with practical measurements made in ventilation circuits simulated in a physical model seems to confirm such differences. It is concluded that although a mine ventilation computer model is a very powerful tool, it can be utilized to its full potential only if reliable input data are provided.

Jan 1, 1987

By W. Z. Choi

In our previous work, a population balance model describing the simultaneous processes of size reduction and mineral liberation has been developed. The experimental verification of this model, however, has been limited to a binary mineral system containing only one composite particle class. When considering multiple classes of composite particles, the estimation of model parameters becomes much more difficult. In the present work, a procedure for estimating model parameters for a multiple composite class model has been developed. Emphasis is placed on the direct experimental determination of these parameters. The physical significance of the breakage rate function and the liberation function in characterizing the liberation process is also discussed.

Jan 1, 1987

The height of permanent slopes at the Panguna mine of Bougainville Copper Limited will vary from 350 to 950 metres. A few degrees difference in slope angle has a large effect on the ore/waste stripping ratio. Optimum slopes can be achieved if longer batter slopes (exceeding 45m height) are excavated using bulldozers to trim parallel to controlling fracture surfaces. Unnecessary slope flattening by incorporating benches can cost millions of dollars in lost ore. Faults and other major weaknesses, which can result in wedge failure or erodible zones have been treated successfully with shotcrete, rockbolts and cable dowels. To minimize support effort and interference with mine production, early identification and treatment of unstable areas is important.

Jan 1, 1987

By Wilton Johnson

Native asphalt was produced by four companies in two States, Texas and Utah. Bituminous limestone, used primarily as a paving material for street and road repair, was produced by one firm. R. L. White Co., Dabney Quarry, Uvalde County, TX. Gilsonite, a solidified hydrocarbon found only in Utah and Colorado, was mined by three firms: American Gilsonite Co., a division of Chevron Resources Co. (a subsidiary of Standard Oil Co. of California); Ziegler Chemical and Mineral Corp.; and Hydrocarbon Mining Co. (a subsidiary of Oberon Oil Inc., a Utah corporation), from properties in Uintah County, UT. Gilsonite is used for a variety of purposes including automobile bodysealer, light-weight aggregate for cement used in oil well drilling, asphaltic building board, protective coverings, anticorrosive paints, and roofing compounds. Gilsonite production in 1985 declined 57% owing primarily to reduced oil well drilling activity. The value per ton was essentially unchanged.

Jan 1, 1987

By Richard D. Miller

The helium resources base of the United States was estimated by the Bureau of Mines to be 1,070 Bcf as of January 1, 1985. These resources are divided into four categories in decreasing degree of assurance of their existence: (1) helium in storage and in proved natural gas reserves, 280 Bcf, (2) helium in probable natural gas resources, estimated at 243 Bcf, (3) helium in possible natural gas resources, estimated to be 287 Bcf, and (4) helium in speculative natural gas resources, which makes up the remaining 260 Bcf. These helium resources are further divided into depleting, non-depleting, and stored classifications. The depleting resources are those associated with natural gasfields that are, or will be, produced for the natural gas they contain. Almost all of the helium in potential (probable, possible, and speculative) natural gas resources is included in this classification. These depleting resources are estimated to contain 900 Bcf of the total helium resource base. Helium resources contained in nondepleting natural gas resources, those in shut-in, abandoned, or otherwise nonproducing natural gasfields, are estimated to total 133 Bcf. There is 37 Bcf of helium in storage in the Federal Government-owned Cliffside Gas Field near Amarillo, TX.

Jan 1, 1987

By Priscilla P. Nelson

Many concepts concerning equipment selection, performance prediction, and evaluation of support requirements for tunnel construction in soil or hard rock tunnels cannot be extrapolated directly for application in soft rock (compressive strength between 1.0 and 35.0 MPa). Case histories for small diameter (less than 3.5 m) tunnels in Austin, Texas, are analyzed to gain insight into particular problems encountered during tunnel excavation in weak sedimentary rock, and the performance of different excavation systems are compared.

Jan 1, 1987

By Y. P. Chugh

The paper discusses laboratory and field studies to analyze time-dependent deformation behavior of immediate weak floor strata in an Illinois coal mine. In the laboratory, core samples of the immediate floor strata were subjected to incremental creep tests under unconfined compressive stress. Both axial and lateral creep deformations were recorded. Time-dependent behavior was reasonably characterized by a Burger model with one Kelvin-Voigt unit. The elastic and viscous parameter8 of the model were found to be stress-dependent, but in the range of 40% to 80% of the failure stress, the effect of stress was relatively small. Therefore, a linear visco-elastic model was developed to represent the laboratory time-dependent behavior of immediate floor strata. Such a model may be acceptable for the design of partial extraction mining systems having extraction ratios of 40% to 60%. Field observations of roof-floor convergence (floor heave) at the mine also indicated a time-dependent behavior similar to that observed in the laboratory. Field time-dependent behavior was also characterized in terms of a Burger model with one Kelvin-Voigt unit to obtain scaling factors between the field and laboratory parameters. This approach should help in predicting likely floor heave in the mine based on laboratory creep tests. It was concluded that additional studies in the field are required to arrive at more reliable correlations between the two sets of parameters.

Jan 1, 1987

The Round Hill gold-scheelite deposit is located three kilometres from Macraes Flat and approximately 60 kilometres due north of Dunedin, New Zealand. A mining feasibility study is currently being undertaken on the deposit by BHP Minerals (New Zealand) Limited, who are the managers and operators of a Joint Venture with Home Reef Mining Limited. BHP has a 70 per cent equity in the project area.

Jan 1, 1987

By C. Babbitt, J. O’Green, N. I. Jayaraman

In many mines, dust-laden air from an entry being driven by a continuous miner will contaminate the intake air to the roof bolter operator and other downwind personnel. Through a US Bureau of Mines (USBM) contract, Foster-Miller Inc. has evaluated several control techniques to reduce the respirable dust exposures of downwind personnel. One fan and tubing technique consisted of bypassing the miner-generated dust directly to the section return. The results of the evaluation of this technique revealed that reductions in dust concentrations of 90% or more can be achieved at downwind roof bolter locations. A second method was to clean the dusty air from the upwind continuous miner by using a dust collector. The cleaned air was then supplied to the bolter through collapsible tubing. An underground evaluation showed reductions of 82% to 96% when the dust collector was operating. A third method was to reduce the quantity of dust contributed by the miner to the return airstream. A water-powered scrubber was installed over the throat area of the continuous miner. More than 1.18 m3/s (2500 cfm) of dusty air moved through five tubes with dust collection efficiency exceeding 75%. Underground evaluation results showed that return dust concentrations were reduced by about 60%. This paper discusses the ventilation and dust control techniques used for personnel downwind of the continuous miner.

Jan 1, 1987

By D. B. Stephens

Assessing the occurrence of natural ground-water recharge at mine and mill waste disposal sites may be crucial to addressing regulatory agency concerns regarding the potential impact of waste seepage on ground-water resources. Recharge has been shown to occur even in semi-arid areas where annual lake evaporation exceeds precipitation. Permanent storage of waste seepage in the unsaturated zone is not to be expected if recharge occurs under natural conditions. Establishing the direction and rate of fluid movement in the vadose zone by field measurements is an important element that should be included in the site selection process.

Jan 1, 1987

By Jacques Mongrain, Serge Barbeau, Gary Brierley

The Communaute Urbaine de Montreal is currently involved in construction of the South Interceptor which consists of 53 kilometers (33 miles) of 1,800 mm (6.0 ft) to 5,400 mm (18.0 ft) diameter tunnels for the purpose of collecting, storing, and delivering sanitary and combined sewage to the treatment plant. Work is divided into ten separate contracts; nine of which have already been bid. The purpose of this paper is to describe construction activities that have been performed through the end of 1986 with emphasis on a general layout of facilities, a summary of subsurface conditions, and brief descriptions of actual construction activities for the six contracts where tunneling has been performed. All projects are being excavated with tunnel boring machines.

Jan 1, 1987

By A. Visnapuu

Excessive noise and high vibration are inherently associated with equipment used in the mining, extraction, and processing of mineral resources. High vibration degrades structural components, often leading to catastrophic failure and loss of productivity, and excessive noise can result in permanent hearing loss. In order to foster efficient utilization of the Nation's mineral resources and minimize occupational hazards associated with mineral processing, the Bureau of Mines investigated the relationship between the microstructures of carbon and alloy steels and cast irons and their damping capacities (ability to absorb vibration). Researchers measured damping capacity and other properties and investigated the effects of carburizing, spheroidizing, and annealing. The investigators found that in carbon and alloy steels, rounded colonies of fine-grained pearlite in a ferrite matrix correlate well with low damping capacity. Steel microstructures that exhibit sharp-faceted pearlite in ferrite matrix and partially or fully spheroidized cementite in ferrite show considerably higher damping. In cast irons, the lowest damping capacity is associated with nodular graphite microstructure, and the specific damping capacity (SDC) increases as the graphite micro-structure progresses from nodular to compacted to flake. Predominant ferrite in cast irons is also associated with good damping. SDC data are presented for selected carbon and alloy steels and cast irons.

Jan 1, 1987

By S. Chander

The formation of surface films on pyrite has been studied through electrochemical techniques of cyclic voltametry and AC impedance measurements. The characteristics of the surface films depend upon the conditions of oxidation and the source of pyrite. At potentials near 0.0 V, some pyrites have large values of polarization resistance showing a certain degree of passivity. Some pyrites show more passivation than the others, however. On oxidation, metastable phases of Fe(OH2) and Fe(OH3) form which transform to more stable 3 phases on aging. The growth of surface films near the corrosion potential of pyrite follows a linear kinetics which is attributed to a chemical (or an electrochemical) reaction as the rate determining step. The surface film is considered to be a hydroxide or an oxide rather than sulfur because the later is expected to be limited to a monolayer in alkaline solutions. This study has also demonstrated that AC impedance measurements can be used to study the growth characteristics of films at mineral/ solution interfaces.

Jan 1, 1987

By Newell R

The influence of layering on the rate of heat transfer through a packed bed consisting of particles of two different sizes and heat capacities has been determined by measuring the heat front velocity through beds of quartzite particles and iron ore pellets. The heat front velocity through the layered beds was less than that through a bed consisting of a random mixture of the par- ticles. This is due to the formation of an interface in which the smaller pellets in one layer penetrate into the layer of quartzite Below.

Jan 1, 1987