Search Documents

By S Lukovic, Robert Briton, Calvin J. Konya

Investigators have reported that charges which are decoupled from the borehole wall produce different fragmentation then those which are fully coupled. The difference in effect could be as a result of energy doss during transmission across the air gap or it could be due to the change in detonation characteristics of the explosive as a result of the change in confinement on the charge during detonation. In order to better understand the phenomena of decoupling, a research project was conducted at the United States Bureau of Mines Station, near Pittsburgh, Pennsylvania. It was decided to use shock and bubble energy tests along with simultaneous velocity measurement to determine the mechanics of decoupling and energy transmission. Two explosives were selected for the test, one dynamite and one water gel. Test results indicated that decoupling could both boost the total energy output of the explosive and that further decoupling would drop the energy output.

Jan 1, 1987

By M. C. Esposito

Seven pyrite samples purified from coal sources and one ore source pyrite (for comparative purposes) have been characterized by chemical and mineralogical analyses, inherent floatability, apparent specific gravity, surface area, semiconductor type, optical anisotropy, dissolution and oxidation rate. The data clearly demonstrate that pyrites from various coal sources differ not only from ore pyrite but from each other as well.

Jan 1, 1987

By J. W. Rold

In 1973 housing and construction conflicts threatened Front Range gravel resources. The legislature addressed the problem by passing HB 1529, which required the Colorado Geological Survey to map the deposits and forbid local governments to change lands over commercial mineral deposits from zones allowing mineral development to zoning which conflicted with development. It charged counties to develop Master Plans for Extraction. Plans must consider resource quality, multiple-sequential-use potential, surrounding area compatibility, neighbors, quality of Life, extraction maximization and reclamation potential. Imprecisely worded statutes, budgetary constraints, lack of enforcement and political pressures have limited benefits from the law.

Jan 1, 1987

By W. J. Schlitt

Introduction Heap and dump leaching are low-cost metal production techniques that are gaining in popularity among gold and copper producers. However, the flow of solution in heaps and dumps has received little attention in the literature. This is unfortunate since solution flow is one of the few parameters subject to operator control. Thus, solution management may well influence both operating costs and plant performance. Costs aside, there are two important aspects of solution flow to be considered -the metallurgical and the hydrological. Some of the metallurgical factors have recently been discussed (Jackson and Ream, 1980; Schlitt, 1984; Schlitt and Nicolai, 1987). These cover solution application rates and methods, irrigation rates, leach-rest cycles, and nonvertical solution flow. According to Caldwell and Moss (1985), however, the hydrological aspects may be more significant than the metallurgical ones. In particular, a phreatic surface will form when excessive flow leads to an accumulation of water and the associated buildup of pore pressure within the rock pile. Such internal flooding can either originate at the foundation or at some other zone of very low permeability. The latter condition gives rise to an impounded volume of solution, i.e., a perched water table (see Whiting, 1985). Caldwell and Moss point out that a rising zone of saturation is probably the most common cause of dump failures. Of course, such failures have even occurred in heaps that were carefully prepared for leaching (Milligan and Engelhardt, 1984). Thus, flooded conditions and perched water tables represent an important safety consideration as well as having an impact on metallurgical performance. The following sections describe a case history in which a perched water table developed within a copper leach dump. The description includes background information, solution flow rates, and metallurgical data. Then this situation is compared to one involving normal drainage. Description of the leach system The leach dump in the case history is located at a shutdown open pit copper mine. It was built in two lifts, with the second added some 20 years after the first. There is little detailed information available on the initial lift. It was built with rail¬hauled waste and was generally less than 30 m (100 ft) high at the crest. The area available for leaching was about 120 m (400 ft) wide and more than 380 m (1250 ft) long. The dump surface was prepared for leaching by dozing ponds approximately 12 m by 12 m by 2.5 to 3.0 m deep (40 ft by 40 ft by 8 to 10 ft). The ponds were leached by flooding with barren leach solution returned from a scrap iron cementation plant. Based on mill feed at the time, the average waste grade was probably close to 0.4% Cu. The first lift leached well. It accepted high flows, which together with the waste grade, produced a rich pregnant leach solution (PLS). Old records indicate a PLS of "50 lb Cu/ 1000 gal," or about 6 g/L. As later drilling would indicate, such a high tenor led to dissolution of considerable scrap iron that was returned to the dump. The iron then hydrolyzed and settled out on the pond bottoms. In addition, the waste settled substantially so that the unleached crest was 3.0 to 4.5 m (10 to 15 ft) above the ponded area. Eventually, the leachable copper was extracted and the dump became less permeable. Thus, the PLS tenor dropped until it became uneconomical. About ten years later, mining resumed and the decision was made to add another lift to the dump. This was done without giving much thought to a subsequent leach operation. Hence a 24-m (80-ft) lift was built on top of the original dump. The surface of the latter was not prepared in any way, e.g., by leveling and/or deep ripping, prior to over-dumping. Examination of subsequent drill cuttings indicated that the new lift contained about 0.2% Cu, with chalcopyrite and chalcocite (50:50) being the predominant copper minerals. Most of the chalcocite occurred as rimming on the abundant pyrite, with the pyrite to chalcopyrite ratio estimated at 10 to 1. The use of 100- and 120-ton trucks for haulage caused some waste compaction during emplacement. In addition, the host rock itself was relatively soft, being a porphyry intrusive material that was partially altered to clay. As a result of the initial compaction and clay swelling, the rate of water percolation from the new leach ponds was slow and the ponds often contained considerable standing water. Even frequent ripping failed to provide a sustained improvement in the percolation rate. The poor surface permeability was exacerbated by hydrolysis of iron salts which settled as a layer on the pond bottoms. Partly as a result of the permeability problems, metallurgical performance was not up to expectations. These had been based on laboratory tests which showed about 20% copper solubilization in two weeks. Continued copper extraction in the tests also suggested that a substantial percentage of the copper would eventually be recovered. However, the PLS grade in the actual operation peaked briefly at about 0.48 g/L Cu (4 lb Cu/1000 gal), then declined to a range of only 0.24 to 0.36 g/L Cu (2 to 3 lb Cu/1000 gal). The poor leaching was traced to a lack of oxidation of the sulfides. There were two principal observations supporting this conclusion. First, there was no evidence of any heat being generated within the dump. As discussed elsewhere (Schlitt and Jackson, 1981; Hiskey and Schlitt, 1982), pyrite oxidation is quite exothermic and the high pyrite content of the waste should have led to an increase in the temperature of the leach solution as it percolated through the rock pile. Second, there was no sign of any natural convective air flow through the dump.

Jan 1, 1987

By Mortimer J. Richardson, Earl H. Malmstrom

INTRODUCTION The art of placer gold mine evaluation and mining has had an interesting evolution beginning in earliest times. DE RE METALLICA (c.1556), documents the use of rockers, circular sieves(jigs) and riff lest for classifying, concentrating and recovering placer gold, respectively. During the late 1800's in the heat of the international gold rush, a bucket ladder mining dredge containing its own processing plant was developed that enabled digging of placers to bedrock that were inaccessible to the hand miner. The power driven churn drill was developed at about the same tie that facilitated more rapid and larger scale sampling of placers to bedrock. The mineral jig was applied in the early part of the 1900,s to begin the replacement of riffles on placer dredges. Mining dredges proliferated in California and New Zealand to mine the deeper placers and spread throughout the world. The companies that were leaders in dredge mining technology conducted experimental work that advanced the state of the art by processing of gravels with jigs and amalgam systems to recover gold on board dredges in a continuous process. This paper will synthesize the technology of placer gold exploration, mine development and operation into guidelines for evaluation and development of small-scale prospects. Prospect Reconnaissance The location of a prospect usual1 y results from some physical evidence of the presence of gold and/or past mining activity. Any earlier activity that may have produced gold from the prospect, should be investigated before making the trip. The initial reconnaissance should attempt to verify a near-surface presence and then make observations concerning the geomorphic characteristics that relate to placer gold accumulation. Estimates of the probable depth, breadth and length of mineable gravels can be made from the surf ace by the experienced placer mining engineer. With this information, he can speculate on whether there is a viable prospect to be pursued. The placer mining engineer should be experienced in panning samples found in shallow diggings or from existing pits. This will give him immediate indications of gold presence without fear of "salting" by an over-ambitious promoter of the project. The same capability of panning is important during the other sampling phases. A thorough knowledge of logging and calculating the results is essential to proper evaluation of the deposit' s tenor. Evaluation Methods Depending upon the character of the prospect such as river, benches, terraces, jungle, the type of equipment to conduct sampling of the deposit must be determined. In most cases, the drill has replaced bulk sampling. The churn drill has had the greatest amount of accumulated experience but is slow. The reverse circulation drill (RC), is limited by its lack of verification in subsequent mining in order to prove its reliability. However, in the hands of knowledgeable placer mining engineers experienced with its use and calibration, it may be used. The RC Hammer drill (such as the Becker), can be as much as ten times faster than the churn drill and compress the time necessary to prove a prospect, or, to disprove it. All costs in balance, it is often cost effective over the churn drill.

Jan 1, 1987

Introduction The mine winder is an essential element in the mining of ore in deep level mines and therefore requires a high degree of reliability to avoid interruption of production. Failure of any component on a winder may also be dangerous and expensive to repair. The larger the failure the larger the stoppage. The failure of a winder drum is the ultimate catastrophe, not only because of the cost of replacement, but also because of the lead time in procuring a new drum. Today these types of failure are not as common but many failures have occurred in the past and even today many an old winder is con- sidered for a new and often more arduous duty. As far back as the turn of the century a lot of information had been gathered to try and clear up the complexities of the multi- layering effect of coiling rope under tension onto a drum. Before comparing results obtained by various researchers the nature of the pressure distribution between rope and drum due to multi-layering will be discussed briefly.

Jan 1, 1987

Nickel laterite approximately 40% of the remainder caning deposits. ores are the source of the world's nickel with from sulphide ore Although laterite ores are near the surface and cheap to mine they require significantly more energy to treat than sulphide ores. The escalation of oil prices comiencing in 1973 meant that nickel laterite refineries using oil as an energy source were placed at distinct disadvantage relative to sulphide refineries or those with coal derived energy. The Queensland Nickel refinery commenced a construction programme; in 1980 to allow ore drying and power generation to be converted from oil to coal. Since late 1981 ore drying has been undertaken using heated air from two moving grate spreader grate stokers. The changeover from oil to coal drying proceeded without process disruptions. This paper discusses the plant changes required to allow the receipt of coal and the operating performance obtained from the coal fired air heaters.

Jan 1, 1987

By R. W. Barbaro, J. M. Mutrnansky

This paper presents a nonlinear integer goal programming model that optimizes a mineral production schedule while considering the penalties and bonuses based on quality variations in the final product. It involves five coal quality goals plus a profit objective in its formulation and uses the weighting method of goal programming for a solution. The goals to be sought involve the sulfur, ash, heat content, moisture content, and ash softening temperature of the blended coal product. The model is linear in its handling of most of these goals but uses a piecewise linear integer formulation for the sulfur and heat content bonus and penalty schedule. The model is applicable to any mineral product blended from several different sources and subject to a varying price dependent on blended product quality or qualities. However, it seems to be most pertinent to optimizing production schedules for coal deliveries to power plants. Accordingly, the model is applied to a hypothetical coal production problem where multiple coal mines are operated to supply a final blended product to a power plant. In this example, the price paid for the coal is assumed to be a function of five of the most important coal qualities. The problem is solved as a direct function of the coal supply contract, thus removing the necessity of determining the weighting coefficients on a subjective basis.

Jan 1, 1987

By M. McPherson, G. Danko

Methods of measuring in situ rock thermo-physical properties are rapidly evolving. Among those existing in the literature, a particular measurement procedure was selected for further development. The measurement is based on creating a spherical temperature field in a drill hole using a point source heater of constant heat flux. The bivariate temperature distribution 0 (r, t) is measured at several points along the length of the drillhole, radius r from the heater and at particular time intervals (t). A number of different evaluation methods were tested for calculating the unknown thermal conductivity (k) and diffusivity [] from the measured temperature and the known heat flux. The results showed that evaluation using the finite difference scheme and small temperature differences measured at points close together, cannot give a reasonable result. In order to solve the problem a new general analytical evaluation method is developed. Using an appropriate technique, it is possible to simultaneously obtain values for k and [], incorporating a semi least square technique to reduce the uncertainty in the evaluation. The new device and evaluation method makes it possible to obtain from a single drill hole highly precise k and [] values within an 8 hour period. The method has been used in several underground mines in the U.S. with good results.

Jan 1, 1987

By Pollard D. M

The removal of nickel from lead by sulfur drossing was investigated using a technique which models industrial batch decoppering practice. Successful denickeling to 0.005% (Ni)pb was consistently obtained in the absence of silver, well below the experimental equilibrium value of 0.015% but still above levels obtained in industrial practice. Silver appeared to have little effect upon denickeling. The final nickel content was dependent upon the initial nickel content, the total sulfur addition and the stirring time. The presence of nickel was found to give no assistance to successful decoppering. Simul- taneous removal of nickel and copper was observed at silver contents in excess of 0.02%. Extended stirring resulted in a further lowering of the nickel content but reversion of copper to the bullion was observed. Experimental work has shown that nickel can be removed by a standard decoppering operation; a procedure which is used in secondary lead re- fining. Alternatively nickel can be removed during initial decoppering in primary lead re- fining operations.

Jan 1, 1987

By M. S. Janssen, J. L. Taylor, M. A. Ford, E. B. Viljoen, H. A. Simonsen

The Stilfontein and Buffelsfontein Gold Mines, near Klerksdorp in the Transvaal, had accumulated a large amount of uranium-containing residue and, when the price of uranium rose in the 1970s, consideration was given to the possible recovery of this uranium. Preliminary tests showed that concentration of the uranium prior to leaching would not be economic. However, the pyrite in the residue could be concentrated by flotation, and the flotation concentrate could be roasted to pro¬vide both enough acid for leaching the uranium and a calcine from which the gold could be recovered. The feasibility study showed that a uranium operation of 270 kt per month would be most economically attrac¬tive, and a plant of that size was accordingly designed and built. In the first six years of its existence, the plant treated over 20 Mt of residue and produced about 3,5 kt of uranium oxide. During that time, the plant was con¬tinually being improved to make it more reliable and cost-efficient. This paper analyses the operation of the plant during its first six years from the viewpoints of its mechanical, process, and economic performance. The criteria on which the selection of the process was based are reviewed and compared with the actual performance of the plant, emphasis being placed on the leaching, solid-liquid separation, recovery, and purification stages.

Jan 1, 1987

By M. C. Radomsky

Approximately sixty, small, surface coal mines in Pennsylvania participated in a program designed to improve safety performance in the workplace. The method involved the use of safety sampling and observation to assess the safe standards of worker behavior and work conditions. Data were collected through the use of operation-specific, on-site safety records covering seven major occupational units. Workplace events observed (acts and conditions) were assigned a hazard classification; feedback, both immediate and delayed was initiated to improve safety performance. The experiences drawn from this pilot project have proven the need to continue to pursue this behavioral approach; however, a stricter methodology needs to be adopted in the collection and analysis of data.

Jan 1, 1987

By Todd S. Harris

Industrial minerals or non-metallic minerals are loosely used terms applied to a diverse assortment of materials which, in many cases, have nothing more in common other than the fact that they are neither metals nor fuel minerals. To help bring order to this otherwise random assortment of minerals, we have grouped these materials into two main categories; chemical and physical minerals, and nine sub-categories based on end-use applications as shown in Table 1. Chemical minerals are products which are principally used for the specific chemical elements they contain, whereas physical minerals are products which are used to meet specific performance specifications. The latter part of the 1970?s, in particular 1978, were considered peak years in terms of production and sales for many industries, By using 1978 as a base year, we can evaluate wherethese markets stand today after the recession of the early 1980's and the recovery which began several years ago. From this historical overview and appraisal of the current situation, various assumptions can be drawn as to which markets are expected to perform well into the 1990's.

Jan 1, 1987

By Travis Q. Lyday

Fiji has been an independent country within the British Commonwealth of Nations since 1970. It consists of an archipelago of more than 300 islands ranging from tiny coral atolls, cays, and rugged coral limestone islets, to the larger mountainous islands of Kandavu, Taveuni, Vanua Levu, and Viti Levu of volcanic origin. The islands of Fiji straddle the 1800 meridian about 1,800 kilometers south of the Equator in the part of the southern Pacific Ocean known as Melanesia. The production of gold and silver from the Emperor Mine at Vatukoula on the island of Viti Levu, the main island of Fiji, remained Fiji's only metallic mineral producer. Mining began at the Vatukoula site in 1933, producing 124 million troy ounces of gold and 147 thousand troy ounces of silver by yearend 1985.

Jan 1, 1987

By K. P. Wright

"Twenty-five years ago, there were about thirty-two gold mines operating in Canada; nine of these have been in continuous operation since then and are still operating. Three of these are part of the Dome Group. Operations of these three and of the newer mines in the Group are referred to in discussing process development over the last twenty-five years.Of the Dome Mines Group, Dome Mines Limited, Sigma Mines (Quebec) Limited, Campbell Red Lake Mines Limited, Detour Lake Mine and Kiena Gold Mines Limited, three have been in continuous operation for the last twenty-five years. Dome has operated for seventy-seven years; Sigma about to complete fifty years, and Campbell approaching forty. Overall, milling processes are virtually the same as they were twenty-five years ago. Tota1 go1d production from the three mines has hardly changed; 1960 production, 416,700 ozs. versus 411,300 in 1985. Milling costs have risen by a factor of six or seven and gold price from $35/oz. in 1960 to $322 in 1985.Basic flowsheets are relatively unchanged. Sigma is an all cyanidation mill grinding in cyanide solution; Dome operates gravity concentration and cyanidation; Campbell gravity concentration, flotation, roasting and cyanidation. All three use Merrill-Crowe zinc precipitation.Detour and Kiena are two examples of the major change in gold processing in the last twenty-five years - carbon-in-pulp. This process has brought along with it other changes, such as, carbon stripping and reactivation, electrowinning, and induction furnace melting. Modern mill design with its use of outside thickeners and agitators, bulk handling of reagents, instrumentation, etc., has made a radical change in operating conditions and appearance of the new plants."

Jan 1, 1987

By Peter G. Kovalchik

To compare the viability of the new fuse wire arc test (FWAT) as a substitute for the comparative tracking index (CTI) for determining surface resistance to electrical tracking, the Bureau of Mines constructed a fuse wire arc tester and undertook a detailed testing program for testing insulating materials used on explosion-proof enclosures. This report describes the Bureau's apparatus, the two methods (CTI and FWAT), and the results of the Bureau's testing, showing comparisons of the FWAT with the CTI. Results showed strong correlation between the two methods, as all specimens tested that had CTI ratings of 400 V ac rms and above passed the 10-test sequence with the FWAT, whereas all specimens with lower CTI ratings failed, with the number of tests to failure corresponding roughly to the descending CTI rating order.

Jan 1, 1987

By R. T. Stain

Integrity testing of deep foundations is now common practice in Europe, indeed in the City of London such testing is a contractural requirement on every site. This paper is in two parts: Part 1 describes the most commonly used test methods and their applications. Part 2 presents a case history where both of the above techniques were used.

Jan 1, 1987

By T. F. Dumm

With increasing interest in the physical cleaning of fine coal, there is a need for extension of the sink-float analysis procedure to finer sizes. Problems arise, however, in ensuring complete dispersion of the particles in the heavy liquids. A procedure has been developed in which surfactants are used as dispersing agents and solids concentration is minimized (using a simple formula to estimate the minimum weight needed for statistical reliability). Using centrifuges to increase separation rates and sub-sieve particle size analysis of the specific gravity fractions, a complete size-specific gravity distribution can be obtained. Analyses have been performed on coal samples as fine as -10 µm.

Jan 1, 1987

By S. Abe

Various copper anodes to be electrorefined were subjected to a heat treatment comprising annealing at a temperature in the range of 700 °c to 1,000 °c followed by a slow cooling preferably on the order of about 150 °c, and using these heat treated anodes , a series of dissolution experiments were conducted under conventional electrorefining conditions. The results obtained have indicated that the above annealing/slow cooling process dramatically improves the dissolution activity regardless of the type of anodes. As an example, passivation times of l to 3 minutes in a standard test have been increased to more than 80 minutes by this innovated heat treatment. Other advantages sterning from the improved anodic activity include reduced electrical short circuiting which results in substantial labor effort in the tankhouse, reduced energy requirement, and reduced cost of processing anode slimes because the amount of anode slimes is reduced. In addition, this process gives rise to a dramatic change in the nature of anode slime layer formed in such a way that a comparable final cathode copper product can be achieved even from high-impurity copper starting material.

Jan 1, 1987

By R. Jacobson

This paper presents comparison of proposed future solution and in-situ mining methods for in-situ leaching and recovery of uranium, gold, silver, and copper. We propose to show that in the future new extraction methods for each metal will eventually evolve for each hydrometallurgical process step, i.e. in-situ leaching, recovery, and concentration; precipitation and reduction; and drying, when required--without generating waste or bleed streams. In the future, to be highly profitable, these forms of mining will develop into an integrated system to eliminate waste streams using safe, powerful lixiviants. This integration will include, with some exceptions, improvements in the following areas of process development: 1. Lixiviant selection and in-situ leaching technique, 2. Target metal recovery and concentration (at a surface hydrometallurgical facility) from the circulating pregnant lixiviant stream, 3. Target metal precipitation or reduction, where decant water from the precipitate dewatering step is reusable for resin or solvent strip liquor (eluant), 4. Final preparation of target metal for sales, i.e. drying, purification, casting, packaging, 5. Restoration where most of the groundwater restoration process is performed at the same rate as multi-wellfield mining.

Jan 1, 1987