Search Documents

By Priscilla P. Nelson, Francis L. C. Fong

Introduction Fracture mechanics is the study of the behavior of cracks and their modes of propagation. During cracking, energy is consumed in creating new surface area. The more energy a material absorbs, the higher is its fracture resistance. This fracture energy is provided either by work done externally, by the release of elastic strain energy within the cracked body, or by a combination of these two effects. Fracture resistance is measured in terms of either the stress intensity factor, K, or the energy release rate (also referred to as crack driving force), G. For linearly elastic materials, these two quantities are related by the following equation: [ ] where [u] is Poisson's ratio and E is the modulus of elasticity. Both K and G are direct functions of the applied force and the crack length. The process of rock cutting with full-face tunnel boring machines (TBMs) involves the indentation of a rock surface by rolling disc tools. Excavation occurs as fractures, extending from the locus of chip indentation, propagate between concentric disc grooves and liberate rock chips from the intact rock face. Since disc cutting is achieved by a fracture process, it is logical to anticipate that differences in cuttability of a variety of rocks should be related to the variation of fracture material properties among the rocks. Such a relation has been demonstrated between the performance of full-face TBMs and the critical crack driving force for excavation in relatively high strength, brittle, low porosity, isotropic rock (Nelson et al., 1985). The objective of this paper is to report on the results of a continued investigation of the relationship between fracture material properties and the effectiveness of disc cutting. Additional reliable data on full-face TBM performance is difficult to obtain, so that the results of disc linear cutter tests performed by the Transport and Road Research Laboratory (TRRL) (U.K.) are utilized in this study. Fracture Material Property Evaluation If a crack tip is subjected to a perfectly plain strain condition, many materials will behave in a brittle manner, and the material resistance to fracture is constant during crack growth. This resistance is referred to as the plain strain fracture toughness, believed to be a material property. The standard testing procedure for this parameter is given in the American Society for Testing and Materials (ASTM) test designation E399. To ensure plain strain conditions, acceptable specimen geometries are specified. Unless these geometric specifications are adhered to, the measured fracture resistance is regarded as the apparent fracture toughness, and a subscript Q is used, as [ ]. The methodology adopted by ASTM E399 is within the framework of Linear Elastic Fracture Mechanics (LEFM). This approach assumes that material resistance against cracking is developed instantaneously, without initial stable or subcritical crack extension. Prior to crack advancement in rock, however, much of the crack driving energy is absorbed in a localized volume in front of the crack tip, referred to as the plasticity or microcracking zone. This capability for energy absorption substantially increases material resistance, and a crack may be arrested unless an increased crack driving force is applied. The LEFM or plain strain assumptions would underestimate the actual fracture resistance of such a material. Such a conservative approximation may be desirable in the design of structures against fatigue or brittle failure. In mining or tunneling, however, an underestimation of crack resistance can lead to the selection of underrated excavation equipment and a decrease in production efficiency. The development of fracture resistance in rock is best described by the material resistance curve, or R-curve, which is a plot of fracture resistance as a function of crack extension. Typically, peak resistance is only reached after a finite amount of subcritical crack growth. The

Jan 1, 1986

Pressures are foreseen for departments of metallurgy to make. radical changes in their undergraduate curricula. The curricula need to be made more attractive to high'school students in -order to increase the number of enrolled students. The distinctive character of extractive metallurgy needs to be emphasised to resist encroachment by chemical engineering. There should be content relevant to each of the professional functions and, particularly, to' society's broad expectations of metallurgists. Content, teaching methods, etc. need to be acceptable to women, mature-age -students, Aboriginals, and other groups, as well as young white males. Learning experiences should be negotiable by the students in response to the advent of learning packages delivered via personal computers. All of these needs could be satisfied by a radical change. in attitudes and objectives during the design; implementation and evaluation stages of . a new type of curriculum, using a wide range of problem-based learning experiences..

Jan 1, 1986

By V. A. Evans

The preparation of a paper reporting fluorspar economics in the United States at one point in time could have been somewhat complicated be- cause of the number of producers, both large and small, that derived production from different locations throughout the Western U. S. and the Southern Illinois and Western Kentucky fluorspar districts . Companies such as Allied Chemical and William- son Mining operated in the Jamestown district of Colorado. In Walden and Salida, Colorado, the Colorado Fluorspar Company operated mines and mills.

Jan 1, 1986

By Andrew M. Leszcykowski

In 1984, personnel from the U.S. Bureau of Mines examined the 9,550-acre Yatahoney Creek Wilderness Study Area (WSA) for mineral resources. This study area, in southwestern Idaho, is underlain by tuffs and basalt of Tertiary age. Owyhee County mining records and U.S. Bureau of Land Management records, and other references were examined prior to the field study. There are no known mines, claims, or prospects in or near the WSA. No evidence of mineral deposits or occurrences was observed. Oil and gas leases or lease applications are in the southern portion and northeast corner of the WSA. Although placer gold exists in the Owyhee River drainage, there are insufficient deposits of gold-bearing gravel in the Yatahoney Creek WSA to enable mining. INTRODUCTION The U.S. Bureau of Mines (USBM) and the U.S. Geological Survey (USGS) conduct mineral surveys of designated wilderness study areas (WSAs) 1/ to ensure mineral values that may be present are considered in wilderness recommendations. The USBM examines known mines, prospects, and mineralized sites, and the USGS performs geologic mapping, and geochemical and geophysical surveys on an areal basis.

Jan 1, 1986

By Geoff W. Seward, Charles J. Maes

INTRODUCTION The work of the metallurgical engineer engaged in developing a leach, solvent extraction electro- winning process usually begins in the laboratory and generally proceeds via pilot plant testing before finally resulting in a commercial operation. The path leading to the development of the eventual process will involve a test program on leaching in order to derive information on the amenability of the copper-bearing material to acid dissolution, under various conditions. Commonly in North America the leach process of choice is either dump or heap leaching but it may also be in-situ leaching or the treatment of mine waste- waters and bleed streams. In the past, agitation and vat leaching have also been included in the list of options. Currently the economics of copper production dictate that only material of mineralogy and grade, capable of being leached without prior milling, will lead to a viable process. This is not necessarily true in other parts of the world where grades are higher and milling costs lower and therefore this paper con- fronts all the techniques available to the metallurgical engineer in terms of the evaluation of the solvent extraction process. Understanding the objectives of a laboratory and pilot plant evaluation of a solvent extraction route is important and these are described in some detail in this paper. Of at least equal importance is understanding limitations of such a test program and this aspect of process development is also discussed with reference to the kind of equipment and experimental practices that have been shown to produce results consistent with the objectives. WHERE TO BEGIN? At the inception of a project much information is developed on the variables of the leach process and indeed in some instances the type of leach that best suits the ore to be treated is the subject of intense investigation (Wadsworth 1983). The decision to treat the leach solution by solvent extraction focuses attention on the selection of the extractant most suited to the nature of the chemical composition of the solution. A laboratory screening program will probably need to be arranged in order to assist in narrowing the options and the following is suggested for this initial screening. Selection of a Representative Leach Solution This is preferably obtained from leaching a representative sample of the ore under conditions likely to pertain in the commercial leach circuit. As the conceptualized circuit flow sheet will undoubtedly involve the recycle of aqueous solutions via the leach, then it is desirable to know the nature of and the likely level of the impurity ions in the solution as well as the concentration of copper. The other most important parameter that is required is the free acid (Anon, Acorga Analytical Method) content of the solution. As a rule of thumb, it is always true that recovery across SX is maximized as the pH of the leach solution rises. Whilst a high pH may be desirable for SX recovery, it is not always desirable for the pH (or more correctly, the free acid) of the leach to rise too high. The working range, therefore, tends to be between 1.5-2.5 pH. At an early stage in process development it is likely that a number of ill-defined conditions will exist, making it difficult to decide on typical leach conditions in which case the screening tests should be carried out using a synthetic leach solution prepared from laboratory chemicals. In doing this the copper and free content should be carefully controlled along with the appropriate addition of major impurity ions as their sulphate salts. Preparation of Suitable Organic Solutions Manufacturers information sheets on the reagents to be tested are required at this stage The information necessary to make an informed judgment on reagent performance is: Copper Uptake Value. This will indicate the amount of copper that can be extracted by a reagent as a function of its operating concentration in a

Jan 1, 1986

By Floyd D. Varley

Outbursts, the sudden and violent out- pouring of material into mine openings, is a ground control problem increasingly encountered in the United States as deeper seams are developed. Outbursts, caused by several mechanisms, are the result of the loading of ground support systems be- yond their designed capacity to failure, manifested in a violent release of stored energy. There are several types of outbursts typical to deep underground coal mines. - Outbursts of the coal face due to the presence of pressure abutments in close proximity to the face. These outbursts are usually accompanied by liberation of large amounts of methane. - Instantaneous convergence of the ribs and floor due to overloading and failure of ribs which lengthens the beam of floor strata sometimes resulting in a chain reaction failure of the mine floor. - violent failure of the confined core of a pillar due to rapid loading beyond the yield point of the pillar.

Jan 1, 1986

By Earl M. Frizzell

This paper addresses considerations for the use of artificial support of pit walls in surface mines, a new project of the Bureau of Mines. Results to date indicate that a polymer-coated cable with embedded grit could provide good anchorage for stabilizing benches and highwalls, and an electronic method of recording discontinuities in the field is being reviewed and developed for application to mining. The objectives of the work in progress are to define the engineering parameters and evaluate the concepts for artificial supports in order to provide safe working environments when pit slopes are steepened to increase ore recovery and reduce overburden handling.

Jan 1, 1986

By Gregory R. Gorrell

The legal issues surrounding the regulation of subsidence are among the major concerns facing the underground mining industry today. Whether subsidence occurs almost immediately as a result of longwall mining or without warning as a result of room and pillar mining conducted years ago, the resulting disputes are highly controversial and typical of the disputes involving the competing interests of surface and mineral estate owners. Until recently, the law governing these disputes was firmly established under the common law. The passage of the Surface Mining Control and Reclamation Act 1, the utilization of new mining technologies, and the general heightened environmental awareness of our times, however, have interjected new issues into this area of the law. State and Federal court decisions and administrative agency interpretations have helped clarify some of the issues. However, as evidenced by the many recent lawsuits between operators, surface owners, and regulatory agencies, many uncertainties still exist.

Jan 1, 1986

In engineering applications of explosives for rock breaking, the released energy is expended mainly into heat, rock crushing and fracturing, seismic waves, air blast, and noise. Those parts of energy which pass into seismic waves and air wave create environmental problems since they are transmitted away from the blast site. In order to predict the environmental effects accurately, one must be able to predict the energy distribution at the source. The energy distribution at the source is significantly controlled by the blast constriction. Consequently, the accuracy of prediction and control of ground vibrations generated by blasting is affected by various matrices of blasting constriction.

Jan 1, 1986

By R. Nendick

"IntroductionThe Ancient Egyptians recovered gold from the mud in the bottom of ponds by having teams of maidens sit around the pond dipping goose feathers dipped in grease into the mud. The gold would preferentially stick to the oily surface and was periodically washed off to give a gold concentrate. This was a forerunner of today's flotation processes.In Greek mythology Jason and the Argonauts pursued the Golden Fleece, which was a primitive form of gravity concentrate produced when gold ore slurry was passed over a sheeps fleece. The heavy gold settled and was caught in the fleece, producing a rich concentrate that allowed Jason & Company to perform the first recorded case of highgrading. The process was a forerunner of todays shuiceboxes used in placer mining.From these simple beginnings, gold metallurgy has progressed to a state where very complex flowsheets are proposed, sometimes to perform a simple metallurgical task. Figure (i) shows a hypothetical flowsheet to identify the range of unit processes that might be brought to bear on a refractory ore. The flowsheet identifies the three primary areas of gold metallurgical operations:Ore PreparationExtractionRecovery."

Jan 1, 1986

By Robert J. Watters, Peter C. Kelsall, Joseph G. Franzone

Two separate studies investigated the compressive strength of basic igneous rocks and its relation to index properties such as porosity, density and soundrave velocity. The rocks tested were weathered dolerite from S. W. England and vesicular lavas from California. In both cases strength was affected considerably by porosity. In the dolerite, strength was also affected by fissures (microcracks) which were formed in the parent rock by shearing and later accentuated by weathering. While test results show that porosity, density and sound velocity are not reliable indices of rock strength, these properties are useful in interpretation of strength test results. Index testing can be used to classify samples according to similar behavior and to recognize the influence of fissures.

Jan 1, 1986

By J. Bowders

A case study describing the expansion of Marion County landfill is presented. The exapansion area is located on a deep mined area. Finite element analyses were used to predict the surface subsidence and associated tensile strains on the landfill liner of the expansion site. A synthetically reinforced liner system is recommended to minimize the impact of the subsurface movements on the integrity of the liner system.

Jan 1, 1986

By M. G. Ayat

A novel tracing technique employing specifically prepared trace particles has been applied to coal preparation separatory systems. The technique employs individually prepared trace particles representing specific known sizes and densities of coal particles. These trace particles are injected into the feed, to the processing circuit, and are then detected at locations in the coal product and refuse streams. It is anticipated that on-line input of the generated partition data will be linked with computer technology to provide rapid analysis of the processing efficiency, and to allow for process control. This tracing technique can revolutionize many processing operations from the diagnostic viewpoint as well as from the coal processing standpoint.

Jan 1, 1986

By Harry W. Campbell

During 1983, the U.S. Bureau of Mines conducted a mineral survey of 19,700 acres that included the Fish Creek Mountains WSA (Wilderness Study Area), 15 miles southwest of the Salton Sea. Two United States Gypsum Co. claim groups in the WSA have more than .20 million tons of inferred gypsum reserves. These high-grade, surface and near-surface gypsum deposits are an extension of a gypsum bed that has been mined continuously since 1922. The Waters prospect in the central part of the WSA has large quantities of limestone suitable for many commercial uses. Sand and gravel is plentiful in the WSA in alluvial fan and ancient shore-line deposits. Limestone and alluvial deposits are not economic because similar material is closer to potential markets. No evidence of energy minerals or geothermal resources was identified in the WSA. A portion of the eastern Fish Creek Mountains WSA is leased for oil and gas exploration. United States Gypsum Co. holds eighteen unpatented placer claims in the northwestern part of the WSA. No other mining claims or mineral leases were identified in the study area. No mineral production is known from within the WSA.

Jan 1, 1986

By Thomas A. Phillips

This publication is an economic evaluation of the Bureau of Mines electrolytic process for recovering lead from scrap lead-acid batteries. In this process, scrap batteries are crushed and separated into metal and sludge fractions. The metal fraction is cast as anodes and electro- refined. Lead in the sludge fraction is converted to lead carbonate by reaction with an ammonium carbonate-ammonium bisulfite solution. The lead carbonate is then dissolved in a fluosilicic acid electrolyte from which pure lead metal is electrowon. A cost estimate is presented for a plant capable of processing 10,000 scrap batteries per day. The fixed capital cost for this plant is estimated to he $14 million on a fourth quarter 1984 basis. Operating costs are estimated to be $0.15/lb Pb recovered. Assuming a lead selling price of $0.17/lb, the interest rate of return on investment after taxes is 11 pct. A lead selling price of about $0.21/lb is needed to obtain a 20-pct-interest rate of return.

Jan 1, 1986

By William H. Sutherland

INTRODUCTION Coal workers' pneumoconiosis and sili- cosis are only two of several diseases which are rlassed as pneumoconiosis. These are respiratory diseases caused by dusts which are inhaled and accumulated in the lungs. The individual particles of dust cannot be seen by the human eye. They are so small that they escape the natural cleansing mechanism of the nose and air passages and make their way down to the terminal air sacs of the lung where they injure the cells and cause the formation of scar tissue. Consequently, if there is exposure to high concentrations of dust over a period of time - usually, a number of years - the amount of scar tissue increases and begins to impair breathing. As a result, the miner develops shortness of breath, coughing and wheezing ad-if exposure continues - this progresses to permanent disability and frequently to death. Death is often due to pulmonary heart disease, the effect of stress on the heart 2s it tries to compensate for the weakened lungs. Specifically, silicosis is an occupational lung disease caused by the accumulation of free silica (quartz) in the lungs. Silicosis is considered the most important form of pneumoconiosis, not only because of its seriousness as a respiratory crippler, but also because of the large number of workers who risk contracting it in a variety of occupations. Quartz is one of the most common substances of the earth's crust, estimated at about 60 percent. Silicosis has been found in coal, metal and granite miners, as well as in other workers, such as sandblasters and pottery makers. Silicosis is also known to predispose the lung to tuberculosis and to increase the chances that a worker will contract chronic bronchitis and emphysema. The seriousness of silicosis was tragically brought to public attention about 50 years ago. During 1932-34, workers were involved in digging a tunnel through rock at Gauley Bridge, West Virginia. While their exposure time was relatively short, they developed silicosis because of the high concentrations of quartz. By 1936, 476 workers had died of silicosis and about 1500 were believed to have the disease (Washington Post, 1982). It is difficult to tell how many coal miners have silicosis. Because x-rays and breathing function tests do not show the difference the type of pneumoconiosis is generally diagnosed by the miner's work history. For example, if a worker

Jan 1, 1986

By R. E. Thill

An ultrasonic, pulse-immersion apparatus and method are described for determining the effects of moisture on the dynamic elastic properties of rock. The method provides an alternative approach for assessing the moisture sensitivity of rocks. Ultrasonic wave velocities are continuously monitored in immersed rock samples as a function of water absorption and time up to saturation. Moisture effects on compressional wave velocity vary as a function of the type of rock and the time and amount of water absorption. Regression analyses are used to curve-fit plots of the data and to derive empirical expressions for compressional wave velocity as a function of water content for different categories of rock. Results indicate that compressional wave velocity can be used to predict both the moisture content and its effect on strength and deformational properties of rock. These results have potential for detecting or monitoring bad roof conditions in situations where the mine rock exhibits strength degradation with moisture absorption.

Jan 1, 1986

By Peter N. Gabby

A mineral survey of 8,300 acres of the 24,980-acre Burnt Creek Wilderness Study Area (ID 45-12), was conducted by the U.S. Bureau of Mines in 1985 at the request of the Bureau of Land Management. The study area is located in Custer County, ID, 90 miles northwest of Idaho Falls. No mines, claims, or prospects are in the study area. The northern half of the study area and adjacent lands to the north, northeast, and east are or were recently under oil and gas lease, Basalt and latite-andesite of the Challis Volcanics predominate in the study area. Several hundred feet east of the study area is a quarry in talus of Mississippian-age limestone that was used for sized 100-pound rock fill in the Old Dry Creek Reservoir dam. Two samples, one taken at the quarry and the other at a limestone outcrop on East Fork Burnt Creek, have CaC03 content in the range of 90 to 95 percent, and is suitable as the limestone component of Portland cement, However, limestone outside the study area could supply foreseeable demand. Lead- silver mineralization has been observed in Paleozoic carbonate rocks elsewhere in the Lost River Range, but these rocks do not occur in the study area.

Jan 1, 1986

By Richard A. Winters

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied 49,875 acres of the 54,833-acre Big Jacks Creek Wilderness Study Area (ID-111-7C) in order to evaluate the mineral resources. The study area is located in Owyhee County, ID, about 15 miles southwest from Bruneau, ID. No mining districts are in the study area, but part of one placer claim, located in 1924, extended into it. The northern portion of the area was covered by oil and gas lease applications; all were cancelled prior to 1985. No economic concentrations of minerals were found in the study area. INTRODUCTION This report describes the USBM (U.S. Bureau of Mines) portion of a cooperative study with the USGS (U.S. Geological Survey) to evaluate mineral resources and potential of the Big Jacks Creek study area at the request of the BLM (U.S. Bureau of Land Management). The USBM examines individual mines, prospects, claims, and mineralized zones, and evaluates identified mineral and energy resources. The USGS evaluates potential for undiscovered resources based on areal geological, geochemical, and geophysical surveys. Results of the investigations will be used to help determine the suitability of the study area for inclusion into the National Wilderness Preservation System. Although the immediate goal of this and other USBM mineral surveys is to provide data for the President, Congress, government agencies, and the public for land-use decisions, the long-term objective is to ensure the Nation has an adequate and dependable supply of minerals at a reasonable cost.

Jan 1, 1986

By Christopher J. Bise

PRINCIPLES OF MINE PLANNING During the initial planning stages, all mining operations are analyzed and evaluated in a similar fashion. This similarity holds true because the mine-planning procedure can be reduced to a network of interrelated systems that are tied together by a common philosophy of mine planning: namely, that the resource is to be extracted in a manner which is safe, efficient, and profitable. The success of the mining operation cannot be guaranteed unless each of these three requirements is met. Fig. 1 shows a flowchart for the initial planning of any mining operation. Notice that there is a preplanning stage that leads to the planning of four interrelated systems. The preplanning stage includes property exploration, estimation of production and manpower requirements, and the establishment of construction timetables. The four systems, evaluated after the pre-planning stage, are broken down into the following: (1) Excavation and handling system, (2) Strata control system, (3) Operating support system, and (4) Service support system. The Excavation and handling system includes the selection of all the equipment for the removal of the resource from its in-place deposit (e.g., draglines, continuous miners, rock drills, etc.) and for the transportation of the mined material from the face (e.g., belt conveyors, trucks, etc.). The Strata control system incorporates all those considerations which maintain the integrity of the roof, ribs, floor, and overburden both during and after the extraction phase; typical considerations in this area include pillar sizing, artificial support of the immediate roof in mine entries, and subsidence protection. The Operating support system contains the "necessary evils" of mine planning; the system consumes a large percentage of the mining engineer's planning time but does not contribute to the actual extraction of the resource. However, if proper attention is not paid to the various components of the system, such as ventilation, drainage, and power, then the mining operation will not perform to its capabilities. Finally, the Service support system is composed of those operations which keep the mine running efficiently; typical examples of these include maintenance and sup- ply. One important concept that Fig. 1 is designed to emphasize is that the four systems are interrelated; typically, a slight alteration of one can affect the performance of another. If these interrelationships are ignored, the effects on the system can be disastrous. The mine preplanning stage and the four subsequent system evaluations constitute the Analysis portion of the mine planning flowchart. After this portion of the study is completed, the overall projected operation can be evaluated by techniques such as financial analysis. This last step in the study is referred to as the Synthesis of the previously calculated parameters into an overall plan. Much has been written about the overall evaluation of mining properties, but, over the past thirty years, very little has been written about the analysis of mine- planning systems in a coordinated manner. Further, those texts which attempted this topic have failed to give sufficient examples for successful implementation, thus supporting the operating engineers' lament that it is easy to discuss theories but difficult to show applications. This text is intended to bridge this gap. Examples of the various stages of the analysis portion of the mine planning flowchart shown in Fig. 1 will be covered in this text, with the exception of the Service support system, since this system is oriented more toward day-to-day planning than long-term mine planning. INTERNATIONAL STANDARDIZATION The benefits that can be derived from an international standardization of the units used in mining engineering calculations are numerous. The interchange- ability of equipment parts and the ability to analyze and compare performance and design specifications on an equal basis are just two of the goals desired by both manufacturers and mine operators. Unfortunately, conversion to an international standard has not been rapidly achieved by engineers in the United States, due to their training under the English system. The Society of Mining Engineers of AIME has made the commitment for the adoption of the Systeme International d'Unites (SI) in all mining engineering calculations. Since many practicing mining engineers and students in undergraduate programs still find difficulty in relating to SI units, the calculations in this textbook will use the English system, with Table 1 available for conversion into SI units.

Jan 1, 1986