Search Documents

The effect of the chemical composition of pulverized bituminous coal particles on their physical transformation during the initial stages of combustion has been investigated. The results suggested that cenosphere formation does not require extensive thermal decomposition of the coal particles. The vitrinites in the bituminous coal softened earlier and developed larger cenospheres than the othe macerals. The coal particles swell to a higher extent during combustion than in pyrolysis; however, the cenospheres formed in the former process experienced a higher extent of fragmentation. The development of microporosity occurred predominantly after the resolidification of the swelled char particles. The type of macerals originally in the coal did not significantly affect the microporosity of the chars. Conversely, the morphology and anisotropy of the chars were strongly dependent on the maceral composition of the coal.

Jan 1, 1986

By S. P. Singh

Rockburst is a sudden manifestation of the release of elastic strain energy stored in the rock. Therefore the tendency of the rock to burst should depend upon its ability to accumulate elastic strain energy. The use of Burst Proneness Index as a simple and reliable indicator to recognize the burst prone situations in the mines has been advocated in this study. The Burst Proneness Index exhibited a strong dependence upon the brittleness, compressional and shear wave velocities and the point load strength index. It was also observed that the Burst Proneness Index increases with the increase in the strain energy per unit volume, c ressive strength and the modulus of rigidity of the rocks. In addition, important causes and the measures to alleviate rockbursts have been outlined in this paper.

Jan 1, 1986

By J. Douglas Causey

In 1984, at the request of the Bureau of Land Management, the Bureau of Mines studied 9,600 acres of the 12,350-acre Antelope Creek Wilderness Study Area (MT-065-266) in order to evaluate its mineral resources. Within this report, these 9,600 acres are referred to as the study area. The Antelope Creek Wilderness Study Area, Phillips County, MT, adjoins the north end of the Charles M. Russell Wildlife Refuge. Considered part of the Missouri River Breaks, the area straddles the edge of a thrust fault zone that has deformed the Mesozoic strata in the west half of the area. Shale, siltstone, and sandstone of Cretaceous Age are exposed in the area. Coal beds averaging 3.0 ft thick occur in the Judith River Formation. About 0.20 million short tons of coal were mined from the Judith River Formation adjacent to the west boundary of the area; no production is known in the study area.

Jan 1, 1986

By Dermot M. Winters, Brent T. Wahlquist, C. Y. Chen

The enactment of the Surface Mining Control and Reclamation Act (SMCRA) in August 1977 addressed subsidence resulting from underground mines, in addition to creating the requirements for reclamation of surface coal mines. Subsidence control regulations pursuant to SMCRA were initially promulgated in March 1979. Several revisions have since been made. In addition, due to court challenges some regulations have been remanded and others are still on appeal. In the meantime the Secretary has agreed to initiate rulemaking on some issues. It is yet to be determined how the prohibition of certain areas from surface coal mining operations under Section 522(e) of the Act applies to subsidence. This presentation discusses the status of the regulations and issues related to or affecting the subsidence regulations.

Jan 1, 1986

A shift in the present day oil exploration scenario from West Coast can be foreseen keeping in mind peak of exploration in Cambay Basin and fast pace of development in Bombay High and its associated fields by the end of this century. Shifts in exploration from structural traps to stratigraphic traps, techno- logical development to drill in deep waters, improving economic situation for oil ventures and proven oil and gas potential of East Coast basins suggest that Indian oil explorat- ion scene will be at its peak along east coast during early 21st century. Hydrocarbon shows in Poonch and Jawalamukhi in Punjab Basin, improvements in drilling to greater depths, better seismic data aquisition, good source rock potential of Subathus and its equivalents and large geologi- cally mapped structures will reopen new avenues for explorationists. Not much exploration effort has been put up so far in Ganga Basin. Keeping in mind size of the basin, sedimentary thickness involved, presence of algal matter deposited in shallow marine environment & higher hydrocarbon indications warrant active exploration. Gondwanas in India having such a large sedimentary area can not be ignored keeping in view generation and production from the non marine sediments of Kenya, Chad, Sudan, Gadon and China. Gondwanas become all the more important in view of gas production from their equivalents-Karoos in Ethiopia and South Africa. In all, above mentioned changes can be predicted in Indian oil exploration scenario during 21st century.

Jan 1, 1986

By J. S. Hu

FTIR spectroscopy has been used for the characterization of adsorbed oleate at the fluorite surface. It has been found that modest changes in the adsorption density at high temperature and high oxygen potential do not provide a satisfactory explanation for the significant increase in the hydrophobic character of the system under similar conditions. Rather, FTIR spectroscopic measurements suggest that chemical interaction between adsorbed oleyl groups occurs at high temperature and/or oxygen potential and accounts for the increased hydrophobicity. Specifically, the intensity of the =CH bond of the adsorbed oleate diminishes at high temperature and/or high oxygen potential. Such a phenomenon was not observed in control tests with the calcium oleate soap. For extensive reaction at the fluorite surface, the presence of a new surface species has been identified. These results indicate that the fluorite surface catalyzes an oxidation and/or polymerization reaction between adsorbed oleyl groups which results in a more hydrophobic structure at the fluorite surface.

Jan 1, 1986

By D. Malhotra, K. Purdy, G. Ramadorai

INTRODUCTION Today, flotation is clearly the dominant mineral concentration method. Since it is a relatively selective process, it is used for almost all sulfide minerals. A recent U. S. Bureau of Mines study indicated that approximately 225 million metric tons of sulfide ore was processed in 67 plants in the United States in 1980 (USBM Staff, 1981). There were over 100 plants processing copper ores in the world (Bassarear, 1985). Sulfide ores containing lead, zinc, copper, molybdenum, precious metals, cobalt, nickel, and iron are generally separated and concentrated by flotation. This chapter briefly reviews the plant practice related to the recovery of the above-mentioned sulfide minerals with emphasis on chemical reagents used for the production of marketable-grade products. PROCESSING OF SULFIDE ORES It is beyond the scope of this chapter to review the milling data for operating plants which have been extensively covered in literature (Tveter and McQuiston, 1962; Rausch and Mariacher, 1970; Weiss, 1985; Crozier, 1979). However, the following generalizations can be made regarding the processing of sulfide ores: 1. The primary grind is targeted to produce as coarse a product as necessary to provide an economic degree of liberation. 2. The concentration process, generally flotation, is designed to produce a concentrate consisting predominantly of valuable minerals and a middling fraction which may require further grinding to produce an optimum release of minerals. 3. The chemical reagent suite (collectors, frothers, etc.) for the separation of sulfide minerals from gangue minerals is generally complex. Total reagents used in the flotation process can be as high as six to eight, as is the case for lead and molybdenite separation from complex sulfide ores. 4. Chemical reagents are generally expensive because of the high selectivity for sulfide minerals. The process flowsheet is dependent on several factors, including ore grade and mineralogical composition. Generic process flowsheets for processing different sulfide ores have been developed for discussion in this chapter. However, there appears to be a consistent relationship between the reagent combination choice and the mineralogical composition of the ore (Tveter and McQuiston, 1962). These are covered in detail in the following sections. LEAD AND ZINC Galena (PbS) and sphalerite (ZnS), which commonly occur together, are the only minerals of lead and zinc, respectively, in most primary deposits. Feed ore grades are typically 1 to 5 percent Pb and 1 to 10 percent Zn. Very often economic quantities of copper and precious metals, silver and gold, also occur with these base metals.

Jan 1, 1986

The New Zealand Steel Ironsand Slurry Pipeline was successfully commissioned in February 1986. The project includes 18 km of high pressure, polyurethane lined buried pipe. McConnell Dowell Constructors Limited has developed a coupling which has allowed this pipeline to be fully welded. The design and development of the coupling and its application on this project is discussed.

Jan 1, 1986

By J. L. Yordan

An induction time apparatus has been constructed in the present work which has a sensitivity limit of 100-150 micro-seconds. The basic unit is similar to the one used by Eigeles and Volova (1960) and Trahar (1983), but it operates with a micro-computer and has a greater sensitivity. Using this apparatus, the flotation chemistry of the quartz-amine system has been studied. It has been found that at a given dodecylamminium hydrochloride concentration, the induction time is at a minimum at approximately pH 10.5. At this pH, the collector hydrolizes to form neutral amine and the flotation recovery reaches a maximumy,suggesting that iono-molecular species are the surface-active species responsible for flotation. This finding confirms the earlier conclusions obtained using the surface tension (Somasundaran, 1976; Finch and Smith, 1973) and contact angle (Smith, 1963) techniques. The induction time measurements have also been conducted as a function of particle size, collector concentration, indifferent electrolyte concentration and temperature. The results are compared with flotation data, and the activation energies for the bubble-particle adhesion have been calculated.

Jan 1, 1986

By R. E. Ray, J. W. Stevenson, J. A. Berry

Conventional concrete block plastered with a cementitious coating is the most common material used in the construction of permanent stoppings to direct airflow in underground mines in the US. All mines experience various degrees of strata convergence depending on depth of overburden, geological conditions, and type of roof support employed. Strata convergence will cause cracks and joint openings in masonry stoppings, resulting insignificant air leakage losses. Where strata convergence is severe, complete structural failure of the stopping can ultimately occur. Reconstruction of damaged or destroyed stoppings adds expensive overhead to mining operations, and even greater expenses are incurred from the additional fan horsepower required to overcome leakage losses. Ideally, a stopping should maintain high resistance to airflow while yielding to strata convergence. By properly incorporating a polyisocyanurate rigid foam material within the masonry block structure, stopping service life can be increased in mines experiencing strata convergence problems such as floor heave, roof loading, and lateral rib movement.

Jan 1, 1986

By J. M. Pachter

Property sales and acquisition are prominent features of today's coal industry. Before selling or buying a site, a company must know the property's economic net worth. Any evaluation of economic net worth would be inadequate if determinations of a property's environmental liabilities and costs were omitted. Short-term and long-term costs can result from liabilities related to reclamation, water treatment, subsidence, and hazardous waste disposal. A structured, interdisciplinary approach can aid in the delineation, summation, and scheduling of these costs and liabilities.

Jan 1, 1986

By L. S. Beck

"IntroductionThe Beaverlodge District is an important mineralogenic province of pitchblende and occupies about 1300 square kilometres centred on Beaverlodge Lake near the north shore of Lake Athabasca in northwest Saskatchewan (Fig. 1). Uranium City is the main settlement of the area and is serviced by scheduled aircraft from Edmonton, some 700 km to the southwest, and from Prince Albert which lies a similar distance to the south.During the summer, boats and barges supply the area from the railhead to Fort McMurray via the Athabasca River and Lake Athabasca, a distance of about 550 km. For the past few years a winter road has been maintained across Lake Athabasca to Cluff Lake to connect with Highway 155.The topography of the area is typical of the Precambrian Shield with generally low relief and a disorganized drainage of numerous lakes separated by hummocky rock ridges, muskeg and drift-covered areas. Local topography in the area is, however, extremely rugged, particularly south and east of Beaverlodge Lake, where resistant rocks form prominent hills and ridges extending as much as 180 m above lake level. Rock exposures are abundant and form over 50 per cent of the land area.History of Exploration and DevelopmentEconomic interest was first aroused by Tyrrell (1896) who described an occurrence of iron formation at Fish Hook Bay; however, subsequent evaluation of the deposit indicated it to be uneconomic."

Jan 1, 1986

The ventilation of a mine is one of the key elements to a successful mining operation. It is, or should be, one of the primary concerns of the mining engineer at an underground mine. Too frequently, however, insufficient thought is given to future requirements. As a result, the mines suddenly find themselves with ventilation problems that cannot be corrected economically, or in short order, and have to suffer the consequences of being on the verge of having units shut down from time to time until the venlilaltion system can be improved. Insufficient ventilation in capital-intensive mining can cause production losses, the values of which far outweigh the significant costs of providing and operating an adequate ventilation plan. Many theories, and techniques in planning and control of underground ventilation systems have been developed over the years . It is the intent of this paper to point out some of the fundamental concepts, from the practical point of view, in the design and operation of a ventilation system, with special reference to underground mines using a room-and-pillar method.

Jan 1, 1986

By V. V. Ershov

Application of computers in the study of mineral deposits pursues two main objectives: 1. obtaining reliable information on the properties of the orebody; 2. providing graphic presentation of this information for its optimal use. These problems are successfully solved if, during preparation of graphic computer software, we apply modern mathematical methods. The present paper treats the problems of using geostatistics for graphic modelling of deposits by means of graphic computers. It should be noted that in this field geostatistical methods may be used for: a) indices evaluation in the nodes of regular grid, or in given blocks, by means of kriging, for its designated purpose; b) for evaluation of accuracy of interpolation methods, traditionally used in computer graphics, and not being optimal.

Jan 1, 1986

By John W. Scott

INTRODUCTION The design criteria for a particular concentration and dewatering project will provide the formal basis for design of the process, equipment and facilities. These criteria will specify the required capacities and operating schedules for the equipment, as well as the quantity and quality of the feed to be processed and products obtained. The general climatic and geographical conditions at the site, specific information on soil or rock conditions; and applicable design standards and codes will also be included. The design criteria will generally be based on an interpretation of testwork carried out on the particular ore and site, and will thus parallel in detail and completeness this testwork. As the project moves from the early conceptual phases through to final detailed design, the design criteria will be developed and become more detailed as information is generated and made available for use. The design criteria are critical to the design effort as the formal specification to the designer of what and how much is to be processed, what and how much is to be produced, and where and under what conditions. The actual design criteria will be a formal tabulation of the design basis information developed for the project in question. For a preliminary study, this may consist of a single page of data; for a feasibility study several pages and for a detailed design up to several hundred pages and multiple volumes. Depending on the complexity of the process and the level of detail included, each project will be unique to some degree. The design process for a project normally progresses from preliminary conceptual phases through to a final detailed design. The criteria used for the initial concepts are generally developed from rough data and preliminary testwork on the ore in question. Regardless, the plant throughput and products are defined, thus giving a scope and definition to the study phase. In some studies a range of throughputs may be analyzed in order to arrive at the most economically attractive size for the proposed operation. This optimum size is then used as the design throughput for the more detailed design phases. Similarly as more testwork results are available and the ore characteristics and process become more well defined a continuous updating of the design criteria is undertaken.

Jan 1, 1986

By D. L. Kiser

Conventional and advanced coal preparation technologies were investigated through both a literature search and through direct contact with investigators and developers. In addition to a brief description of each process, performance characteristics including feedstock type, ash and sulfur reduction, thermal energy recovery and cost are provided in a tabular form. Seven of the most commonly utilized conventional coal preparation processes, including those respectively accepting coarse, intermediate and fine coal feed, were reviewed. It was found that certain properly implemented and well maintained conventional processes were capable of better than 75 percent ash removal while recovering 90 percent or more of the inherent thermal energy. Almost 50 advanced coal preparation processes were investigated based on biological, chemical and physical principles. Physical processes investigated included cycloning, homogeneous heavy media, electrostatic, high gradient magnetic, flotation and selective coalescence. Using pulverized coal as a feedstock, some of these processes are respectively reported to be capable of removing better than 95 percent ash. 95 percent pyritic sulfur, and 50 percent organic sulfur while incurring energy losses of less than 5 percent.

Jan 1, 1986

By R. L. Peyton

Risk analysis is used extensively in many engineering applications. Although its use in the field of dam safety has been limited in practice, it has received considerable attention in recent years in the dam safety literature. Thus far, it has been shown that risk analysis in the evaluation of existing dams has the potential for providing a more rational basis for decision- making because of its focus on the direct issues--likelihood of failure, likelihood of loss of life, and risk cost of damages. It provides for a logical balance between the risk a dam imposes and the degree to which rehabilitation is required, compared to traditional evaluations based on somewhat arbitrarily chosen design events applied to large classes of dams. Dam owners could benefit by optimizing the cost of remedial measures. Downstream landowners could benefit by minimizing the likelihood of flood damages. However, it is also clear that significant technical and policy issues remain to be resolved before risk analysis in dam safety is accepted and routinely implemented in engineering practice. An obvious and important potential application of risk analysis is its use by the state regulatory agency as an in-house evaluation tool, or even as part of regulatory policy, in the implementation of its state dam safety program. Adoption of such a policy would have an important impact on the mining industry. .Although no state dam safety programs are known by the writers to have officially incorporated risk analysis into their regulations, there appears to be considerable interest in the concept. In recent surveys 47 states agreed that the development and promotion of a risk assessment methodology for state dam safety programs should be encouraged (Tschantz, 1983; Tschantz, 1984). The issue has also received important attention within the Association of State Dam Safety Officials (1986). One state-Illinois-proposed regulations during 1986 to allow risk analysis to justify lower spillway requirements for existing dams (Illinois Department of Transportation, 1986). At the Federal level, the National Research Council has found risk analysis especially appropriate for assessing dam safety at high-hazard dams (National Research Council, 19851, the Bureau of Reclamation has published guidelines for incorporating risk analysis into their dam safety grogram (U.S. Department of the Interior, 1986), and the Federal Emergency Management Agency has recently sponsored workshops and supported research related to risk analysis in dam safety (Federal Emergency Management Agency, 1985a ; Federal Emergency Management Agency, 1985b; - - McCann, et. al., 1985a, 1985b).

Jan 1, 1986

By E. F. Evoy

"The Gunnar uranium deposit was within metasedimentary rocks of the late Archaen Tazin Group. These rocks were intensely altered by albitization so that the immediate host to the ore consisted dominantly of albite, and by the subsequent introduction of calcite. The ore consisted of disseminated pitchblende and uranophane in a pipe-shaped breccia zone. Oxidation of the ore was more intense near surface than at depth, but there was no near-surface enrichment.IntroductionThe Gunnar Mine site is on the tip of Crackingstone Peninsula, on the north shore of Lake Athabasca, Province of Saskatchewan, Canada. The peninsula forms the southern part of the Beaverlodge mining area. The ore consisted of disseminated pitchblende and uranophane in brecciated metasedimentary rocks of the Tazin Group, and the deposit was characterized by extreme albitization and subsequent carbonatization of the host environment.Production from the mine began in 1954 and the ore was depleted by 1963. In that interval the deposit yielded about 5 million tonnes of ore containing about I. 75 kg/tonne U3O8. It was mined initially from an open-pit and subsequently from underground; the open-pit contributed about 55% of total tonnage. Uranium was recovered by atmospheric leaching in sulphuric acid, ion exchange concentration, and precipitation with magnesia.This paper is based on studies made during the productive life of the mine and is concerned primarily with pre-ore alteration of the rocks containing the deposit, and with the ore mineralogy."

Jan 1, 1986

A wide-ranging base of jig data was collected from various types of commercial jigs in 9 coal preparation plants in China, and a complete data analysis was made. It was found that the sharpness ofseparation was very variable, which demonstrates the complex interplay of the many factors which influence jig performance. Tests showed that there exist optimum frequency ranges in each compartment of a jig. Stepwise regression analysis indicated that the sharpness of separation is most sensitive to the intake fraction ofthe air cycle, the frequency, and the feed rate. By means of non-linear curve fitting techniques and statistical analysis, several mathematical models were developed to describe both partition curve and the jig performance, for simulation purposes.

Jan 1, 1986

By Virgil A. Marple

The objective of this contract was to investigate time-integrated and real-time methods for determining the diesel exhaust particulate concentration in underground mines, in particular, coal mines. The microorifice uniform deposit impactor (MOUDI) is recommended for obtaining the time-integrated measurement of the size distribution. The mass concentration of diesel exhaust particles can be obtained from the particle size distribution of mine aerosols. On a mass basis, diesel exhaust particles are primarily in the submicrometer size range while coal dust particles are larger. Size distribution measurements made in the laboratory and in three underground coal mines exhibited two distinct modes with the diesel exhaust particles in the smaller particle mode and the coal particles in the larger particle mode. The point of separation between the two modes occurred in the 0.7 to 1.0 pm size range. The separation was found to be independent of mass fraction of the diesel exhaust particles, particle concentration and sampling site. Methods recommended for further consideration as real-time monitors of diesel exhaust aerosols in mines are photometers and filter pressure drop techniques. A preclassifier would be required in both cases to separate the larger dust particles from the sample. The Metrex Mineral/Diesel Photometer should also be investigated further once the electronics problems are eliminated.

Jan 1, 1986