Search Documents

By Pierre Mousset-Jones

A questionnaire was sent out to three classes of mines to determine the extent of the heat problem in U.S. and Foreign underground mines. The following list shows the replies received from this questionnaire, however not all the known hot mines in the US replied. A complete listing of the results can be seen in Appendix I. 1) US coal mines - 37 replies 2) US non coal mines - 23 replies 3) Foreign non coal mines - 36 replies. At the present time there are approximately eleven non coal and one coal mine in the US experiencing heat problems which require special efforts to maintain an acceptable working place climate. However since the survey was completed some of them have been placed on standby. The Mine Safety & Health Administration (MSHA) does not have any specific regulations relating to heat stress. Informally the American Conference of Governmental Industrial Hygienists guidelines are followed which use wet bulb globe temperature (WBGT) with values ranging from 26.7°C to 31.1°C for a moderate workload, and different rest regimes. An MSHA report (Misaqi 1976) recommended that conditions should not exceed 26.1°C WBGT for men and 24.4°C WBGT for women. However, quite recently the organizations involved with planning two of the proposed nuclear waste repositories in the United States, have opted for the criteria of an air cooling power of 300 w/m2, and a WBGT of 27'C respectively.

Jan 1, 1986

Article I1 of the RMCMI Bylaws reads: Section 1. Classes. The membership of the corporation shall be divided into three classs, consisting of active members, life members and senior members, who shall have such rights, privileges and qualifications as these bylaws may provide. The names of all active, life and senior members, together with current mailing addresses, follow. [Lt. Jay Abbott M. L. FOSS Co. 7458 S Jackson St Littleton. CO 80122 Lt. Ronald H. Achziger Midwest Rbr & Sply Co 6404 E 39th Are Denver, CO 80207 ]

Jan 1, 1986

By A. G. Provost

On April 3, 1981, Harrison Western Corporation was awarded a contract by Amax Alloy - A Division of Amax Inc., to sink the Henderson #5 ventilation shaft. The project was located on the Henderson Mine site 88 kilometers west of Denver near the town of Empire, Colorado (Figure I). The Henderson No. 5 Shaft, located in an Alpine environment at an elevation of 3145 meters, was a 9.8 meter diameter concrete lined shaft with a total depth of 793 meters. Work started and continued with Harrison Western employees until January 15, 1982. At that time, Amax made the decision to continue the shaft-sinking with their own labor, and with Harrison Western providing supervision under a management service contract. Shaft sinking continued under this arrangement to October 1, 1982, at which time Amax put the Henderson No. 5 project on standby status until further notice.

Jan 1, 1986

By T. S. McGahey

The southeastern region of the United States has long been a major market area for coarse and medium particle size natural ground calcium carbonate fillers. The primary market for calcium carbonate in the southeast traditionally has been as fillers in building materials such as carpeting, joint cement and roof shingles. In these applications the economic value of the calcium carbonate in the final product is weighted more toward lessening the cost of the final product, as opposed to contributing any desirable physical characteristics. For example, in carpet backing applications the calcium carbonate filler does little more from a physical standpoint than add weight and body to the backing adhesive. The important factor in the use of calcium carbonate in carpet backing is that it can be used at high loading levels to replace the more expensive latex binder, thus lessening the cost of the final product. It is estimated that calcium carbonate producers in the southeast sell in excess of 200,000 tons (181,436,000 kg) annually for use in latex compounds for carpet backing applications.

Jan 1, 1986

By Armstrong M

The Coal Mining Engineering Branch of the New South Wales (NSW) Department of Mineral Resources, in its continuing effort to improve coal recovery from underground coal mining operations, has undertaken a study of the mechanics of sub-surface deformation caused by caving of the extracted area behind retreating longwall faces. The strata movement was monitored by a multi-wire borehole instrumentation system consisting of mechanical anchors installed at different horizons in a borehole extending from the surface to the coal seam. The mechanical anchors were connected to the suspended weights on the surface by stainless steel multi-strand wires. The movement of these weights was monitored as the longwall face approached and retreated past the borehole. The anchors started subsiding as soon as the face retreated past the borehole and continued to subside until the subsidence levelled off when the face retreated 900 m past the borehole. The zone of major caving and bed separation extended to roughly 10 to 13 times the extracted seam thickness and high tensile strains developed inthis zone. The bulking factor of broken strata was less than 1.14 which indicated that the roof layers collapsed in big blocks. The goaf compaction was almost complete when the face retreat was 200 m. Low tensile strains prevailed in the strata overlying the zone of caving and bed separation.

Jan 1, 1986

By Donald S. Skufca

This chapter focuses attention on major factors pertaining to plant design and general arrangement of equipment. Considered are efficiency of operations, coordination of maintenance and repairs, plant testing of reagents and possible future plant expansions. The design and general arrangement of equipment considers accessibility for maintenance and isolation for repairs, minimum personnel for operations and cleanup, safe working conditions with minimum interruptions to operations. The constant introduction of new reagents requires eventual plant testing and the manner of isolating a “line” or part of the facilities to allow comparisons in the testing of new reagents is discussed. As technology improves and process changes occur, additional equipment or plant expansions are inevitable. Space for these eventualities must be considered while the general arrangement drawings are in the development stages.

Jan 1, 1986

Improve transmission of data from an underground mine monitoring system to a remote, mass-data storage system. Background Instrumentation systems in underground mines must operate under environmental extremes of dust and humidity, local electromagnetic/radio frequency (EM/RF) interference fields, and potentially explosive atmospheres. During a recent roof-bolt study performed by the Bureau of Mines, it was necessary to transmit a large quantity of data to a data storage system. Conventional wire cable transmission presented several limitations which often required special electrical isolation or physical protection. Because conventional wire cable presented certain problems, the Bureau of Mines investigated alternative means of data transmission. The research investigation led to the selection of fiber optic cable for data transmission applications. The fiber optic method of data transmission offers several advantages: ? Since the transmission medium consists of light waves, it is safe to use in gassy mines. Where applicable, MSHA permissibility standards for peripheral devices must be met. ? It is lightweight and rugged. ? It can operate up to 131000 feet (4km) without repeaters and without EM/RF field interference.

Jan 1, 1986

By J. J. Renton

The iron disulphide minerals, pyrite and to a lesser extent marcasite, are ubiquitous to coal and coal associated rocks and are the source of nearly all the environmental problems associated with the mining, processing and utilization of coal. The iron disulphides as well as the other minerals in coal exhibit systematic spatial pat- terns of distribution on both regional and local scales and show predictable associations, most of which are determined by the geochemical-sedimentological controls under which they form. It is the purpose of this paper to discuss the geochemical-sedimentological conditions responsible for the formation of coal minerals with special emphasis on the formation of iron disulphides, to illustrate the regional and local patterns of mineral occurrence within coal, to present the microscopic associations of the iron disulphides and finally, to discuss the most important single environmental aspect of the iron disulphide content of coal and coal associated rocks; the production of acid mine drainage.

Jan 1, 1986

By Stone I

Tahmoor Mine is located in the southern Sydney Basin 80km south-west of Sydney and produces 1.2 MT of Bulli Coal annually. Bord and pillar methods used to date will be supplemented by a longwall system. Difficult roof conditions have been experienced since mining began in 1979. A dominantly horizontal stressfield promotes shear failure in the thinly interbedded roof sequence of shales, laminites, siltstones and fine sandstones. General roof conditions and failure characteristics are related to the angle between the roadway direction and the principal horizontal stress direction. The apparent stressfield changes direction, magnitude and the ratio of principal horizontal components across the mine workings in response to both in situ and mining induced causes. Initial roof support of 5 x 2.1 m bolts per W-strap at in intervals, with mesh, was upgraded to include RSJ's in order to support areas of failed roof. This support system was inefficient and costly. A third system of support emphasizes roof reinforcement with full resin encapsulation of 2.1 m bolts in W-straps. The number of bolts per strap (6-8), extra butterfly straps and bolts, and W-strap spacing is determined for each area by expected roof and stress conditions. Intersections are pre-bolted and ribs are supported in some areas. Pillar dimensions, order of drivage and roadway width have each been altered to improve roof control. The intensity of roof deformation at the face varies from panel to panel and causes development rates to decrease to 30% of the maximum. 1. Manager, Tahmoor Mine, Tahmoor, N.S.W. 2. Senior Geologist, BP Coal, Picton, N.S.W. Roof conditions in each area of the mine are characterised and then projected to future development areas based on the relationship between stressfield orientation, relative roadway direction and face conditions. Planning information available includes expected development rates, roof support requirements and areas of changing conditions. Future improvements of strata control involve defining support design parameters for the range of mine conditions already seen at Tahmoor.

Jan 1, 1986

By B. Farouk, D. Apelian

"A numerical model has been developed to predict the temperature history of particles injected in a low pressure d.c. plasma jet. The temperature and velocity fields of the plasma jet are predicted as a free jet by solving the parabolized compressible Navier-Stokes equations using a spatial marching scheme. Particle trojectories and heat transfer characteristics are calculated using the predicted plasma jet temperature and velocity fields. Correction factors have been introduced to take into account non-continuum effects encountered in the low pressure environment. The plasma jet profiles as well as the particle/plasma interactions under different jet pressure ratios (from underexpanded to overexpanded) have been investigated.I. IntroductionIn the plasma spraying process a d.c. plasma jet is used as a heat source to melt and accelerate powder particles which subsequently impinge and solidify on a given substrate. During low pressure plasma deposition (LPPD) prooess, the plasma jet is expanded into a low pressure environment (40-80 Corr) which results in high plasma jet velocities with Mach numbers ranging from 2 to 3. Previous efforts to predict heat transfer and fluid flow in plasmas have made use of incompressible flow formulation employing turbulence models [1-3] for atmospheric plasma spraying. However, these theoretical calculations have been limited to the subsonic flow regime; hence, the compressibility effects and viscous heat dissipation were neglected. In the LPPD process, the plasma jet is operated at the supersonic flow regime, therefore, the compressibility effects and viscous heat dissipation are no longer negligible. This is the main motivation of this work.In addition, production of high quality dense deposits requires that a large fraction of the injected particles be in a molten state when they impact the substrate. An additional motivation for this work is that it is important to understand the plasma/particle heat and momentum transfer since these phenomena dictate both the particle thermal history and particle trajectory.Early computational works in supersonic nozzle field flow [4,5,6] consisted of patching methods that divided the flow field into an invisoid free stream and a viscous boundary and. mixing layers. Each was analyzed independently and coupled through appropriate boundary conditions. Later schemes [7,8] involved solving time-dependent, compressible Navier-Stokes equations over the entire computational domain. These schemes show a great promise in predicting flows with complex structure, and where the viscous effects became prevalent."

Jan 1, 1986

By Sirayanone S, Rashad MZ

An important problem occurring in the iron and steel industry of Egypt is the presence of manganese oxide and chlorine with different percentages in the Bahariya Iron Ore Deposit, Western Desert, Egypt. In this work we used a geostatistical method known as the Volume- Variance Relationship to predict grade fluctua- tions of Fe% , Mn% and Cl% in the ore after blasting a certain volume from the ore deposit, on the other hand, if we have a certain limit for each of these chemical components, we can select the bench blasting dimension to give these limits.

Jan 1, 1986

By W. -S. Hwang, R. A. Stoehr, P. Ingerslev

"The flow of molten metal entering complex two-dimensional foundry molds has been modeled using the Simplified Marker and Cell (SMAC) and Solution Algorithm (SOLA) techniques. The molds were for a series of four and three-spoke wheel designs. The computer calculations were compared to physical experiments in which molten cast iron was poured into C02-bonded sand molds. The metal was photographed with a high speed motion picture camera focused through a Pyrex glass window on one face of the mold. To get good agreement between the calculations and the experiments, it was necessary to accurately represent the velocity through the ingate. This was calculated by application of the Bernoulli equation to flow through the feed system. Some difficulties were experienced with mathematical instability, expecially in the three-spoke design with a narrow ingate. This was overcome by using 100% upwind differencing, and over relaxation parameter near 1.0 (i.e. no over relaxation), and variable mesh spacing.IntroductionModeling the flow of molten metal entering molds has the potential for making significant contributions to the design of feed systems. It will supply information to the computer-aided-design systems of the future that will enable the designer to optimize the placement of gates, dimensioning of passages, and designation of casting speeds. Such design criteria have generally been based on application of energy balance (Bernoulli equation) principles to flow in the sprues, runners, and gates. Indeed, this is the easiest way to determine the proper dimensions to give a suitable filling time for a casting of a given size. A number of computer programs, including one by some of the present authors, have integrated such calculations into CAD systems. l Modeling the flow of metal inside the mold cavity requires other techniques that will handle free-surface transient flow. Stoehr and Hwang reported on the application of the Marker-and-Cell (MAC) technique to mold filling problems at the previous conference in this series at Hennicker, N.H. in 1983. 2 Although considerable progress has been made since that time in improving the accuracy, stability, and convenience of these techniques, the shapes to which they were applied remained limited. Also, physical verification of the results of the calculations was limited to water models.The work to be reported in this paper was undertaken with two objectives: (1) to apply these techniques to more complex and realistic shapes, and (2) to verify the results by comparison with flow patterns observed in molten metal poured into actual sand molds."

Jan 1, 1986

By M. Tomono

Harima Works is operating as the zinc and lead simultaneous smelter utilizing the imperial Smelting Process. The smelter commenced its operation in 1966 with designed capacities of 3500 t/M of zinc and 1500 t/M of lead. After that, owing to the results of progressive developments and improvements in operating efficiency and equipments, it has doubled its production figure. This report reviews our recent developments carried out from 1983 to 1985. Firstly, the furnace bottom design was modified for the purpose of reducing carbon consumption ratio. As a result, shaft operating condition has been satisfactory and carbon consumption ratio was improved by 2%, in addition, furnace zinc production was increased by about 8%. Secondly, the oxygen enriched operation at sintering machine was tested from July 1984 to June 1985, in order to increase the sinter productivity, and to solve the capacity imbalance between sinter plant and ISF. As the test result, it was found out that sulfur elimination rate was increased by approx 10% with the oxygen enrichment of 500 Nm3/hr.

Jan 1, 1986

By Fredrick L. Johnson

No mineral resources were delineated during our investigation of the Antelope Wilderness Study Area (WSA). Only a few claims have been located in the area and only four workings were found. There has been, however, considerable exploration and mining activity in and near the south end of the study area. The Morey mining district, just southeast of the WSA, produced silver, and lesser amounts of gold and lead, sporadically from the mid-1860's through the mid-1960's. Long Lac Mineral Exploration (Texas), Inc. is actively exploring a large block of claims for hot-spring type, low-grade, large-tonnage gold deposits. Their claim block extends into the study area. The WSA, located midway between Tonopah and Eureka, encompasses approximately 87,400 acres. It is underlain by Tertiary rhyolitic and latitic volcanic rocks and by Paleozoic sedimentary rocks. At least three areas in the Paleozoic rocks have many of the favorable criterion for hot-spring type gold deposits; they have been faulted, silicified, brecciated, and hydrothermally altered, and have anomalous concentrations of precious metals and pathfinder elements. With additional exploration in the south part of the Antelope WSA, gold resources may be discovered.

Jan 1, 1986

By Carl H. Eckert, James P. Berson

INTRODUCTION The demand for specialty metals in industrial applications is in it's healthiest state since the late 1970'8, and several specific markets are recording record sales. Such metals as gold, silver, zirconim., titanium, beryllium, gallium, germanium, the platinum group, and the lanthanides accounted for sales in excess of $2 billion in 1985 among the end uses covered in this report. Although specialty metals as a group have suffered the effects of recessionary pressures in the past, these metals have proved more resiliant than such large volume metals as copper and nickel. This is due to the unique physical properties they possess which makes the threat of substitution or replacement through technological development uneconomic. The outlook for these specialty metals is optimistic in electronics, catalysts, ceramics, and alloys, and their specialty status results .in a combined average annual growth in demand of 7% through 1990. WHAT MAKES THESE METALS SPECIAL? Such characteristics as electrical conductivity, corrosion resistance, catalytic activity, thermal stability, and optical properties allow the term specialty to be applied to these metals. More importantly, all of these metals possess more than one of these qualities, as shown in Table 1. [ ] These five major functions are important in the end uses for these metals, although the specific applications vary somewhat. Conductivity in term of low or high electrical resistance is of obvious importance to electronics manufacturers. Producers of circuit boards or semiconductors require such metals as gold, palladium, platinum, and gallium due to their low electrical resistivity. However, these producers also require such metals as beryllium in the oxide form for insulation components because of the compound's low electrical conductivity. Although the lanthanides' conductive characteristics are not particularly attractive in electronics, they are of great importance to alloy manufacturers producing permanent magnets for automotive and computer applications. Corrosion and wear resistant properties are extremely attractive to a number of end-use industries, particularly in view of the estimate by the United States Bureau of Mines that $10 to $50 billion in losses are experienced by U.S. industry due to equipment corrosion and $100 billion due to equipment wear. The strength of high purity titanium and zirconium make these metals the obvious choice for corrosion and wear resistance particularly in the chemical processing industry, where the ability to maintain integrity in corrosive environments is a must. Heat exchangers, nuclear control rods, and a number of parts in jet engines have benefited greatly from the use of these metals. However, such other specialty metals as beryllium, and the lanthanides also improve the wear or corrosion resistance in various products. For example, a beryllium-copper alloy contact maintains it's spring like character, and does not loose this character after repeated use, which could result in the loss of an electrical contact. Lanthanide, in the form of cerium oxide, is commonly employed in alloys used to produce catalytic converter casings for the purpose of reducing damage by corrosive road salt. In some instances, the catalytic activity of several of the specialty metals assists in the economic production of other materials. However, the importance of specialty metals in catalysts is most apparent in catalytic converters for emission control. Platinum, palladium, and rhodium are

Jan 1, 1986

By P. Berendsen

Structures along the rift were subjected to episodic reactivation. Major north-northeast-trending high-angle normal or reverse faults and northwest-trending trans-current fault systems, may exercise control over ore-forming processes. Gabbro and basalt are the dominant igneous rock types. Carbonatite and kimberlite occur in Nebraska and Kansas. Concentrations of Cu, Ni, Co, Ti, Au, Ag and PG-minerals are known to occur in this setting Arkosic sandstone, siltstone, shale and minor carbonate units occur on top of the rift basalts and in flanking basins where they may reach thicknesses of 10 km. The potential for stratiform or unconformity-related metal liferous deposits must be considered.

Jan 1, 1986

The structural pattern of Victoria shows the presence of EW, NW, NE as well as the more readily recognised NNW factors commonly associated with the goldfields. ENE and WNW trends are also present. This structural lattice affects all rocks of the State. Landsat imagery shows that the EW, NW and NE structural elements are closely related spatially to the distribution of Palaeozoic igneous intrusives, Cainozoic volcanic vents as well as all historically important gold mines. It is suggested that the EW, NW and NE structural grid visible on landsat imagery is a reflection of the structure of a mid-crustal layer situated between 3.5 and 17 kms below the surface. The points of intersection of the structural elements of the mid-crustal layer offer most favourable loci for the escape of energy in the form of heat. The correlation between the distribution of igneous plutons, volcanic vents and centres of mineralisation, all reliant on high levels of energy for their formation, indicates the stability of the structures of the mid-crustal layer since early Palaeozoic times. The deep level crustal structures are believed to be, related to the release of stresses placed on the crust since early Palaeozoic times by the rotation of the Earth. A geological model that accommodates the presence of a mid-crustal layer as well as the complexities of the recognised orogenic cycles of southeast Australia is suggested. All 1 000 kg Au reef and deep lead mines fall within 1.5 and 2.5 km respectively of strong linears associated intimately with plutons and volcanic vents. Future exploration of the State is more likely to meet with success if it too is confined to the evaluation of these and similar linears. The mode of mineralisation of any one centre will depend upon the temperature, pressure and geochemical gradients operating on the migrating mineralising fluids as well as the structures in the host rocks. These factors are likely to have varied considerably from one centre of mineralisation to the next and consistency of mineral isation form and depth should not be expected along the length of any single Linear.

Jan 1, 1986

This information circular describes research the Bureau of fines has conducted to improve technology for recovering precious metals from low-grade resources. Many of the reported findings are recent, and some of the work described is ongoing. Topics discussed include cyanidation of carbonaceous gold ores to enhance gold recovery, a new method for precipitating mercury during cyanide leaching of gold ores, a staged heap leaching process to generate suitable solutions for direct electrowinning of gold, the use of anion-exchange resins to recover gold from cyanide solutions, and precious metals recovery from electronic scrap.

Jan 1, 1986

By H. Nakazawa, I. Iwasaki

Galvanic contact, occurring between electrically conducting minerals in flotation pulps, may affect the nature of mineral surfaces and influence their floatabilities. Rest potential and galvanic current measurements were made on an electrode combination of pyrite and pyrrhotite under nitrogen, air and oxygen aeration conditions. The results were correlated with their oxygen-consuming characteris- tics and flotation behaviors. The galvanic contact improved the floatability of pyrrhotite, but adversely affected that of pyrite. Auger electron spectroscopy, X-ray photoelectron spectroscopy, and scanning electron microscopy indicated that the formation of hydroxide or oxide and sulfate species of iron on pyrrhotite decreased, whereas that on pyrite increased when these minerals were held in contact. An electro- chemical mechanism was proposed for the observed behaviors.

Jan 1, 1986

Improve the safety of mine workers by developing a sensitive ground-fault relay system capable of detecting and isolating low level ground faults and thereby minimize the danger of electrocution. Approach Inadvertent, direct contact with energized conductors in underground coal mines is a major cause of electrocutions. Although relay systems designed to protect workers against such fatal accidents do exist in some industries, there are no effective ground-fault-sensing relay systems that address the special problems presented by power systems designed for U.S. mines. The Bureau of Mines conducted research to design and construct a sensitive ground-fault relay for use with low-voltage, alternating current (ac) mine electrical systems. Such a relay, sensing current leakage or faults in an electrical system, would send a trip signal to a circuit interrupting device which would then shut down power.

Jan 1, 1986