Search Documents

By T. M. Klemetti, T. J. Batchler, T. J. Matthews

How representative are partial-panel screen tests of the in situ response of screen to roof and rib deterioration and displacements? Can a more representative procedure that tests up to two full screen panels improve the utilization and effectiveness of screen as a roof and rib support? This paper details a new full-panel screen test procedure and the initial results. The full-panel test frame was designed to test a 2.4 by 3.6-meter screened area with bolt spacing as small as 0.3-meter increments. The initial design included up to 6 screen pull points, but additional locations can be added to produce a more uniform loading. The test frame was developed to capitalize on the capabilities of the Mine Roof Simulator (MRS) at the Pittsburgh Mining Research Division (PMRD) of the National Institute for Occupational Safety and Health (NIOSH). The initial tests included a baseline test of a partial panel (1.22 by 1.22-m screen section) using the original 1.52 by 1.52-meter test frame, a 1.22 by 1.22-meter screen section test in the new full-panel test frame, and two tests of 2.4 by 3.6-meter screened area in the full-panel test frame. The 1.22 by 1.22-meter screen section tests in the full-panel test frame produced a peak load 6% higher and a yield load 30% lower than the partial-panel (original) test frame. The multiple pull points of the full-panel frame produced variable yield, peak, and intermediate loads, but on average were lower than the single pull-point tests. INTRODUCTION Roof and rib surface support has become a major component of the stability and safety of underground coal openings in the past 15 years. The use of screen, either metal or synthetic, has proven to decrease the injuries of underground coal miners. By 2005, there were 466 injuries in the United States caused by roof skin failures, with numerous mines not employing roof screen. In contrast, in 2015 there were 175 injuries caused by roof skin failures, with at least some of the reduction due to the increased use of roof screen. A continued effort to increase the utilization of screen in areas of underground coal mines where workers are traveling and working can reduce these injuries even further. To aid in this effort, the testing of various screen types under various loading and attachment conditions is required. Past testing efforts have primarily consisted of partial-panel testing in a laboratory setting. Laboratory testing of roof screen, both metal and composite, has been conducted in several ways by researchers, manufacturers, and other entities. The primary focus on the testing has been evaluating weld integrity of 1.22 by 1.22-meter screen section tests of various screen types utilized in mining (Dolinar, 2006; Dolinar, 2009; Tannant, 2001). There have also been several efforts at numerical simulation of the screen and screen/rock interactions (Murali et al., 2006; Shan et al., 2014). A few full-panel tests were performed with one pull or loading point in the center of the screen panel (Shan et al., 2014). As most previous efforts have mentioned, the only true way to evaluate the capabilities of screen is to conduct full-panel testing. Single wire strand, weld, and partial-panel (1.22 x 1.22-m) tests as well as numerical modeling only provide insight into the actual response of full-panel screen. A new test frame and procedure have been developed at PMRD to conduct various loading, anchoring, and material testing.

Jan 1, 2019

By Tristan Worsey, Nathan Rouse

Florida is one of the major limestone producing states in the United States. The state has unique regional geology and groundwater characteristics that require equally unique mining methods to extract limestone for construction materials. In many regions, aggregates quarries operate by drilling and blasting underwater limestone and then digging the muck with large draglines, while in others, mining operations are able to operate above the water table.

Jan 1, 2019

By M. Massinaei, S. Abasi, M. Oliazadeh

Reliable measurement and control of the pulp-froth interface (froth depth) in the flotation columns is critical to achieve the desired metallurgical performance. Shallow froths result in a reduction of grade because of particle entrainment and deep froths reduce recovery because of the drop back of entrained and weak hydrophobic particles to the pulp zone. The cleaner circuit at Miduk copper concentrator consists of three parallel MicrocelTM flotation columns 4 m in diameter and 12 m in height. The interface level of the flotation columns is measured by two pressure sensors located at 1.4 and 2.4 m from the cell lip (in the collection zone). In this study the performance of the level detection system at different operating conditions was evaluated. A calibrated float-ultrasonic location system was used for measuring the actual froth depth. The results indicated that the existing level control system was subject to considerable error. The absolute error was found to be 33.27 cm. This was mainly attributed to the constant set-point value assigned to the froth density (ρf=0.3 g/cm3), which actually varies with the operating conditions. The actual froth density at different conditions was calculated and its average value (ρf=0.12 g/cm3) was re-set in the control system. This resulted in substantial reduction in the level-detecting error. Recommendations for more accurate measurement of the interface level were presented. INTRODUCTION Froth flotation is a complicated process because of many involved variables. One of the most significant controlled variables in the flotation process is the pulp-froth interface (froth depth). The froth depth has a profound influence on the metallurgical performance parameters (i.e. grade and recovery). Shallow froths result in grade reduction because of particle entrainment and deep froths reduce recovery resulted from the drop back of entrained and weak hydrophobic particles to the pulp zone (Finch and Dobby, 1990). Various techniques have been developed for measuring the interface level of the flotation cells in the last few decades. These techniques can be classified as: Techniques based on hydrostatic pressure measurements (Finch & Dobby, 1990), Techniques based on the density gradient (float) (Moys & Finch, 1988), Techniques based on conductivity measurements (Uribe-Salas, 1991), Techniques based on temperature measurements (Moys & Finch, 1989).

Jan 1, 2019

By K. Scalise, M. Teixeira, K. C. Kocsis, J. Parrish

"This paper aims to introduce and discuss a newly developed algorithm, which can be uploaded on smart watches and other mobile devices to inform and protect underground personnel working in hot and humid environments. Using this algorithm, the metabolic rate (M) of a worker can be determined in “real-time”. In addition, besides warning signs and alarm signals emitted by the smart watch, the algorithm has the ability to determine work-rest time periods based on the worker’s physiological parameters (e.g. age, height, weight, gender) and the climatic parameters (Td, Tw, flow velocity). This paper also investigates whether a re-designed auxiliary ventilation system can provide appropriate work conditions in the production stopes. INTRODUCTION An underground environment with high temperature and humidity conditions generated from various heat and moisture sources can significantly affect the thermoregulation processes of the human body. This can lead to heat-related illnesses such as heat rash, heat cramps, heat exhaustion, and heat stroke. Heat stroke is a serious illness that carries a high risk of fatality, if the underground workers are not immediately treated and the climatic conditions are not corrected (McPherson, 1993). There are two methods used to control the climatic conditions in underground mines: (1) Using ventilation and cooling systems to reduce the thermal stress on the mine workers, and (2) Reducing the heat transferred to the ventilating air from major sources such as: strata, auto-compression, mining equipment, groundwater, blasting, etc. The heat from strata and auto-compression is transferred to the ventilating air at varying degrees, based on factors such as the virgin rock temperature (VRT), the thermal properties of the surrounding rock formations, and the surface air temperature. However, the use of mining equipment and blasting processes can be managed to reduce their contribution to the mines’ overall heat load. To provide appropriate work conditions, selecting the most suitable cooling method depends on the level of heat to be removed, the location of the problem areas, and economic constraints (Brake & Bates, 2002; McPherson, 1993). Because every mine is unique, it is essential to monitor the climatic conditions to select the most appropriate method of cooling. A majority of the time, simply adjusting or re-designing the auxiliary ventilation system can efficiently remove the heat and dilute the contaminants. This may involve moving the ducting system, changing the size of the duct, changing the size of the auxiliary fan, or switching from forcing to an exhausting fan arrangement. If the required air volumes are higher than the existing primary ventilation system can supply, other measures may need to be taken to increase the airflow delivery. This may include regulating the flow in some areas of the mine to increase airflow to the desired area, adding booster fans, or replacing the primary fans."

Jan 1, 2019

By Frank Hirthammer

Productivity, customer relations, and effectiveness of work depend to an ever-increasing extent on a functioning logistics system tailored to the needs of the user. Of course, it is not possible to cover and explain all aspects of the logistical requirements of even a small part of an industry, in a single article. The article speaks specifically about the particularities and differences in the logistical requirements in the explosives sector. Starting with questions of safety, handling and quality up to the legal basis, there are special requirements regarding the logistics in the explosives sector. The results of innovative logistics solutions are presented using three examples from daily work practice.

Jan 1, 2019

By T. Imgrund, A. Bischoff, S. Spürk

"Specific conditions of underground coal mines at great depth, such as high temperatures, high rates of methane inflow and natural ventilation pressure provide considerable challenges for the reliable design of appropriate mine ventilation systems. For decades coal mining in Germany has coped with these extreme circumstances. Based on these experiences appropriate software tools for simulating mine ventilation networks have been developed and continuously enhanced. This paper examines differences in the simulation results and underlying calculation methods of two software solutions. The analysis is based on the comparison of FlowNetTM and VentSim DesignTM (Version 5.1) regarding the accurate prediction of fluid mechanical quantities and their validation with real measurements. A special focus lies on exceptional ventilation scenarios typical for deep coal mines, like gas inflows, fire events and buoyancy effects. The purpose of the comparison is the future utilization of the experiences gained during mining at up to 1,500 m depth for state of the art ventilation design. INTRODUCTION Ventilation is an essential component of mine operations—as providing fresh air to workplaces, diluting and removing explosive, toxic or asphyxiating pollutants and assuring sufficient climate conditions. On the other hand, the costs of ventilation contribute to a large extend to the overall operating costs of a mine, as the share in the energy consumption of a mine may be in the range of 25–50% (Belle, 2008). Accordingly, proper design of ventilation systems has been a task since early times. Consequently software for modelling of ventilation networks has been developed in order to improve efficiency and accuracy of calculations (Maleki, 2018). Compressible flow has not been considered by initial ventilation modelling software tools. In Germany, the consideration of changes in airflow density—depending on pressure and temperature—in the algorithms of ventilation simulation software has been started in 1974 by Duepre & Hofbauer. This development had been continued by the Pruefstelle fuer Grubenbewetterung (Test Centre for Mine Ventilation) and resulted in the release of a computer ventilation software named “Wetter”. The mine inspectorate of the German state of North Rhine-Westphalia, which supervises the major coal mining district in Germany, declared ventilation simulation based on compressible flow being “state of the art” in 1985 (Pollak, 1985). This pronouncement made allowance for assessing the consequences of underground fires and downtimes of main fans based on advanced software solutions."

Jan 1, 2019

By J. M. Beck

Mineral property appraisers engaged in eminent domain actions on properties for which mining is the highest and best use must be fully competent in all phases of mineral resource estimation, mine project development, and mine operations (or retain the requisite competent assistance), as well as educated in eminent domain appraisal (USPAP Competency Rule). Failure to ensure such triggers the issue of appraisal competence and demonstrates a flagrant disregard of the myriad code(s) and guidelines to which the appraiser is subject. The cavalier assertion of some vague, undefined “latitude” in the valuation process does not exonerate the appraiser from a disregard of the USPAP Competency Rule. Lack of independence (i.e., “advocacy”) in mineral property appraisal is the usual result of a weak background in mining and/or appraisal theory. While it is readily apparent to those able to recognize it in reports and testimony, judges and juries cannot be expected to detect or recognize purposefully misleading (or even fraudulent) valuation concepts or testimony. Purposeful deception by the appraiser can lead to specious over-compensation of the property owner (thus victimizing the taxpayer); or, a failure to provide appropriate and just compensation to the property owner – yet, the purpose of an eminent domain proceeding is to leave the property owner no richer or poorer as a result of the taking. This paper highlights some of the deceptive practices encountered in litigation settings and raises issues of competency, professional ethics, and the effectiveness of the inherent enforcement capabilities within those institutions awarding professional certifications. INTRODUCTION The practice of eminent domain mineral property appraisal requires (particularly with respect to undeveloped mineral properties) that the appraiser possess the requisite level of competence in all phases of mineral resource estimation, mine project evaluation, mine development, and mine operation (through closure). To the extent the appraiser lacks such competence, it is incumbent on the appraiser not only to divulge this lack of expertise but also to seek competent assistance in the performance of the appraisal. This competence or expertise can only be obtained through a combination of appropriate and relevant technical education and direct mining industry experience. There exist a number of professional certification and/or credentialing authorities that speak to such competency. In a similar manner, eminent domain mineral property appraisal (as the term implies) also requires that the appraiser possess the requisite level of competence in the practice of eminent domain appraisal. This competence or expertise can only be obtained through appropriate and relevant education, direct knowledge of appraisal theory, particularly as it relates to the concept of eminent domain, and licensure.

Jan 1, 2019

By K. Parameswaran, A. Veek, A. Fernandez, P. Safe

ASARCO LLC (Asarco) Hayden Copper smelter, in Hayden, Arizona, has operated continuously (except for minor labor and economic curtailments) since 1912. The current plant configuration comprises INCO flash smelting, Peirce Smith (P-S) converting and fire refining/anode casting. In order to comply with the U.S. Environmental Protection Agency (EPA) 1-hour National Ambient Air Quality Standards (NAAQS) for sulfur dioxide promulgated in June 2010, the Hayden smelter had to increase overall sulfur fixation from approximately 95 % to 99+ %, requiring a retrofit of the existing converter department and upgrade of associated emissions controls systems. The Converter Retrofit Project (CRP) involved replacing the five existing 13’ diameter Peirce-Smith converters (2 blowing, 2 hot standby) with three new 15’ diameter Peirce- Smith converters (1 blowing, 1 hot standby) to allow for more effective process gas capture using the existing acid plant contact section. Significant upgrades were made to the acid plant wet gas cleaning section and converter primary gas handling system to improve capture performance, reliability, and sludge handling. In addition, a new tertiary gas capture system was installed to further minimize fugitive emissions from the converter aisle. The existing furnace tapping ventilation ESP was replaced with a new baghouse to enable at least 50% SO2 removal using high-surface-area dry lime injection, which was also implemented on the existing converter secondary gas baghouse system. The first two converters and all gas handling system improvements were started up in April 2018, and the third converter was brought online in November 2018. This paper presents the regulatory context; genesis and rationale for CRP; detailed description of the project; challenges during commissioning; system improvements implemented, and design considerations made, and systems performance and process optimization achieved since startup.

Jan 1, 2019

By G. Stokreef, B. R. Davis, M. Kadiyski, T. LeBel, Alvear Montenegro, R. Parra, V. Montenegro

A drop tower and methodology were developed to study the impact of mineralogy on the flash combustion behaviour of copper concentrates. Reaction shaft conditions of a flash furnace were simulated using a drop tower reactor and different molar ratios of oxygen gas to sulphur in the feed. Five feeds were tested in the drop tower including pure minerals chalcopyrite and pyrite as well as two mineralogically distinct copper concentrates and a blend of the two. The behaviour of each of these five feeds were evaluated through analysis of the solid combustion products for elemental sulphur, mineralogy and particle size. Desulphurization curves for each of the feeds were produced. It is thought that the desulphurization behaviour of pure minerals can be used to estimate the behaviour of a concentrate and that a blending recipe could be developed, which can optimize the chemical and mineralogical inputs to the flash furnace and guide operations on the optimum furnace conditions. Overall, the drop tower has proven to be a useful tool for studying flash combustion processes. Experimental results suggest that mineralogy has a significant impact on the conditions required for the production of matte with consistent grade. This finding is especially significant for custom smelters, which may see several different blends in a day. INTRODUCTION Flash furnace smelting is a continuous feed, batch tap, pyrometallurgical process that is used to produce copper matte from copper sulphide concentrates. Dried concentrate(s), silica flux, and secondary materials are blended to a target chemical composition, typically given by the Cu/S ratio, before processing. This fine, dried feed is dispersed throughout the heated furnace reaction shaft with an O2-enriched reaction gas. The particles heat up in the shaft of the furnace, ignite and undergo reactions that pre-oxidize the iron sulphide and some of the impurities in the feed. Oxidation reactions in the shaft of the furnace desulphurize the feed and produce an SO2-containing off gas. The reacted particles fall into the furnace settler and separate into a Cu-rich matte and an iron-silicate slag, while the SO2-containing off gas is carried out of the furnace for heat and dust recovery, as well as H2SO4 production. Some concerns during operation of the furnace are dusting, over or under oxidation of the feed, and a stable flame.

Jan 1, 2019

By Weijie Wei, Jinwang Zhang, Jiachen Wang, Yang Li

"Longwall top-coal caving (LTCC) mining technique is one of the important methods for underground thick seam extraction in China. The coal seam in LTCC panel is divided into two parts: bottom-coal and top-coal. The bottom-coal is mined by conventional longwall method while the top-coal is mined by caving method. The top-coal caving process in LTCC and block caving process in metal mine are both gravity flow of loose ore/coal blocks. However, the presence of caving shield in LTCC makes the characteristics of drawing body shape in the two caving processes differ a lot. This paper discusses the influence of caving shields on the characteristics of drawing body shapes in light of recent studies of the top-coal drawing process. The theoretical model for describing the drawing body shape in LTCC is proposed both along the seam strike and seam inclination. Then, the experimental data are used to validate the correctness of the theoretical model. Furthermore, two examples of how the theoretical findings assist LTCC mining are given and discussed.INTRODUCTIONLongwall top-coal caving (LTCC) mining technique and large-cutting-height mining technique have been widely used for extracting thick coal seams in China. About 0.6–0.7 billion metric tons of coal come from longwall top-coal caving panels every year. The maximum annual production is 15 million metric tons per panel _The mining method employed in such panel is a combination of top-coal caving mining technique and large-cutting-height mining technique, which is suitable for seam height between 12–20 m, as shown in Figure 1. Apart from China, LTCC has also been employed in some coal mines in Australia and Vietnam (Le et al., 2017).The coal seam in a LTCC panel is divided into two parts: bottom coal and top coal. The bottom-coal is mined by the conventional longwall method, while the top coal is mined by the caving method. The top-coal caving process in LTCC and block caving process in metal mines are both gravity flows of loose coal/ore blocks, as shown in Figure 2. However, the presence of caving shields in LTCC causes the characteristics of the drawing body shapes in the two caving processes to differ significantly.There are two main differences between the blocking method and the top-coal caving method:"

Jan 1, 2019

By A. Belleau, F. Lavoie

"Quebec Iron Ore Limited (QIO), a subsidiary of Champion Iron Limited (Champion), secured assets in early 2016 from the previous Bloom Lake operations in the heart of the Labrador Trough region of Northern Quebec, Canada. A plan was developed to bring the Bloom Lake facility back in operation once the iron ore market conditions improved. The project restart involved several aggressive moves to change operational effectiveness, one of which was the utilization of the existing Phase 1 Plant with an upgraded process flowsheet and equipment. The production target was 7.4 million tonnes per annum of 66% iron ore concentrate with an approximate 10% increase in iron ore recovery. The Phase 1 upgraded flowsheet was initially based on review of historical Phase 1 data and pilot testing data undertaken during the original Phase 1 operation and was finalized once additional metallurgical test work and process modeling was carried out by Mineral Technologies in late 2016. The final upgraded flowsheet is comprised of rougher spirals, rougher middling scavenging spirals, and an up-current classifier (UCC) with overflow scavenging spiral stage. A portion of the gravity circuit tailings treated by a series of wet high intensity magnetic separators (WHIMS) to boost overall iron recovery. This paper will describe the efforts taken to test and design the Bloom Lake Phase 1 upgraded flowsheet and report on the plant performance since commissioning in first quarter of 2018.SITE HISTORY The Bloom Lake iron mine property is located approximately 13 km north of Fermont, Quebec, and 10 km north of the Mont Wright iron ore mining complex, property of ArcelorMittal Mines Canada. The Bloom Lake mine facilities include a 32 km railway to efficiently transport the high-quality iron concentrate to a loading port located in Sept-Iles, Quebec. The Bloom Lake property was first explored in 1951 and went through multiple minor exploration campaigns by different companies up until 1998. A major exploration program was conducted by Quebec Cartier Mining (QCM) in 1998. This program included line cutting, surveying, diamond drilling, geological mapping, mini-bulk sampling, bench-scale preliminary metallurgical test work and preparation of a “mineral resource” estimate."

Jan 1, 2019

By Alan Tordoir, Mark Roberts

The drill and blast process is a critical function within the production cycle which significantly impacts the ability of an operation to effectively meet its safety and production targets. Acknowledging that D&B design and reconciliation practices were conducted inconsistently across operations, a Group wide initiative was launched to embed a standardized design and reconciliation platform in line with the company’s Operating Model principles. A technical system was selected to deliver the digitalization of critical D&B information and enable ‘analyze and improve’ routines for design compliance monitoring and downstream productivity optimization.

Jan 1, 2019

By Hajime Miki, Gde Pandhe Wisnu Suyantara, Shigeto Kuroiwa, Eri Takida, Tsuyoshi Hirajima, Masashi Yamane, Yuji Imaizumi, Mitsuru Sawada, Keiko Sasaki

Selective flotation of molybdenite and chalcopyrite using various oxidation treatments (i.e., ozone treatment, hydrogen peroxide, and Fenton-like reagent) was studied in this work. It was found that ozone treatment produced a depressing effect on both minerals, resulting in a lower separation of both minerals. On the other hand, oxidation treatment using hydrogen peroxide (H2O2) and Fenton-like reagent could deliver selective oxidation on chalcopyrite surface and depress its floatability. However, bench-scale copper- molybdenum (Cu-Mo) flotation tests show that oxidation treatment using H2O2 required a higher dosage of H2O2 and a longer treatment time in order to deliver comparable flotation results to that of conventional Cu- Mo flotation using NaHS treatment. On the contrary, Fenton-like reagent could deliver selective Cu-Mo flotation results comparable to that of NaHS treatment at a lower dosage of H2O2 and a shorter conditioning time. Contact angle measurements and X-ray photoelectron spectroscopy (XPS) analysis were employed to understand the depressing mechanism of these oxidation treatments. It was found that the chalcopyrite surface covered by various oxidation products that render the surface hydrophilic. Meanwhile, the surface of molybdenite was slightly oxidized, making the surface remained hydrophobic. INTRODUCTION Molybdenite (MoS2), the main source of molybdenum, is associated with copper sulfide minerals, mainly chalcopyrite (CuFeS2), as a trace mineral. Molybdenite is a valuable mineral and plays an important role in making the copper-molybdenum (Cu-Mo) processing plant economically viable (Laskowski, Castro, & Ramos, 2013). Therefore, it is important to recover molybdenite efficiently and effectively and separate it from copper minerals. Conventional separation of copper and molybdenum minerals is usually carried out in selective Cu- Mo flotation process using a copper depressant (i.e., sodium hydrosulfide (NaHS), Noke’s reagent, or cyanides) (Ansari & Pawlik, 2007; Bulatovic, 2007). However, this process still suffers due to imperfect molybdenum recovery. Moreover, the copper depressants use in this process are toxic and harmful to the environment. As alternative, various methods have been developed to replace these toxic and hazardous depressants, for example, by synthesizing new non-toxic or low-toxic depressants or by using various oxidation methods such as sodium hypochlorite in an alkaline medium, manganese dioxide, oxygen, and plasma pre-treatment (United States Patent Office Patent No. US 2559104 A, 1951; Patent No. US2238250 A, 1941; Barzyk, Malysa, & Pomianowski, 1981; Hirajima et al., 2014). However, the oxidation phenomenon and mechanisms are still not clear since detailed surface analyses have not done and the plasma pre-treatment method is facing technical issues for industrial scale application.

Jan 1, 2019

By Mathias Jern, Ruilin Yang

A blast vibration model has been developed that simulates effects of almost all blast design parameters on the blast vibration peak particle velocity (PPV) from a production blast with multiple blastholes at a given point of interest in the rock. The velocity of detonation (VoD), initiation points, explosive types (density, VoD, energy), charge decoupling, and decking in each blasthole are simulated along with other blast design parameters. The information from signature hole blast vibration and the blast design are the input to the model. The model can be used to assess blast damage in proximity of blastholes as well as far field vibration PPV.

Jan 1, 2019

By E. Landry, W. Naudts

"The amenability theory was developed by Alex Naudts and considers grouting operations as continuous permeability tests where Newtonian test fluid water, is replaced by a cementitious or solution grout. It utilizes hydraulic conductivity and grouting data to establish the amenability coefficient of a particular grout zone. The amenability coefficient reflects the quantity of apertures or voids accessible to the selected grout, divided by the number of apertures accessible to water, in the zone intersected by the grout hole. By calculating, in real time, the effectiveness of a particular grout at the start of a grouting operation, the most appropriate grout to match design criteria can be targeted. By incorporating the amenability theory in every grouting operation, schedule savings and an increase in productivity are typically achieved. Three short case studies illustrate different enhancements in productivity: At an underground mine during the construction of declines, a cement based suspension grouting program was highly ineffective and did not appear to affect the inflow into the mine workings. The amenability theory was utilized to evaluate the grouting program and based on this evaluation, changes to the grouting program were made which allowed the grouting to meet the project’s objectives. On another project, a pre-excavation grouting program implemented during shaft sinking operations utilized the amenability theory to select the most suitable grout for the program. Schedule constraints also influenced the selection of the grout. In the third case history presented, the amenability theory was used to select the grouting sequence of every individual grout hole for a grouting project in a highly heterogeneous soil formation. INTRODUCTION The amenability of a given soil, civil structure or rock formation for a particular grout formulation is a measure of the ability of that grout to permeate the pores, fissures and apertures water will flow through. The amenability coefficient of a particular grout for a specific zone equals the percentage of apertures, pores and fissures accessible by water that are also accessible by grout. Grouting should be viewed as a continuous permeability test, where the apparent in-situ hydraulic conductivity value for a particular grout zone is continuously evaluated, using grout instead of water as test fluid."

Jan 1, 2019

By Phillip J. Mackey, Susumu Okabe

Copper mining and smelting has been carried out in Japan for over 13 centuries and in fact stretching back into antiquity. In 1889, the first electrolytic copper refinery in Japan based on Elkington’s principles was started by Furukawa Mining at Honjyo in downtown Tokyo based on the multiple or parallel system. Within two decades, a number of other copper refineries had begun operation. Interestingly, but perhaps not surprising given Japan’s long history of copper production, this first refinery in Japan commenced just ten years after the first refinery in the USA (1879), and not long after the first plants in Europe. By 1935, as a result of growth in copper demand, there were six domestic copper electro-refineries in Japan with an installed capacity of 97,800 tonnes/a, while actual production was 71,200 tonnes/a. Since about 1932, the majority of these plants were based on the more common parallel or multiple system. In 1946, just after World War II, domestic production capacity had dropped considerably to 29,000 tonnes/a, however with reconstruction, capacity and production expanded rapidly, with production reaching 81,000 tonnes/a in 1955, 187,000 tonnes/a in 1960 and 307,000 tonnes/a in 1965. The introduction of the first refinery and the early ones that followed and subsequent developments are discussed in this paper. The major technical achievements during the high growth period from 1945 to 1963 included: the use of fire- refined anodes; the introduction of newly-developed rectifiers; the introduction of lead-lined or vinyl-lined concrete cells; improvements in the electrolyte heating system; application of improved anti-corrosion materials and the introduction of heat-insulating surface coverings. In 2018, Japan’s refined copper production totaled 1,595,000 tonnes of copper, with Japan ranking third in the world after China and Chile. INTRODUCTION In 2018, Japan’s refined copper production totalled 1,595,000 tonnes of copper and Japan ranked third in the world for refined copper after China and Chile (Wood Mackenzie, 2019). There are now eight copper refineries in Japan which provide Japan’s production of refined copper. These plants are listed in Table 1 (Wood Mackenzie, 2019), also showing the production trend since 2013; in general, production over this period has been relatively steady. The Toyo plant is now the 7th largest copper refinery in the world after several large plants as rated by capacity in China, Russia and India (ICSG, 2019).

Jan 1, 2019

By Jonathan Heiner

Rio Tinto Bingham Canyon Mine started its South Wall Push Back (SPB) in 2011. This push back will mine through the only road to the pit bottom (the 10%). The pit bottom is the main ore sector for the mine and supplies about 80 to 90% of the ore. In late 2017 the mine set off a blast in SPB that created a small wedge failure on the high wall between SPB and the 10%. This wedge failure released a rock approximately 20 minutes after that blast that rolled down the wall landing on the 10% near and then contacting a light vehicle

Jan 1, 2019

By Carricajo T., S. Nazari

This paper discusses a unique dynamic solution for optimizing comminution area in real time. The proposed technology is a combination of model predictive controller, optimization methods and real-time digital twin for mineral processing. For grinding area, the ultimate goal of an effective control strategy is to maximize the mineral processing, reduce energy consumption and stabilized size classification. To have a continuous and effective comminution operation, a reliable control system that minimizes the need for human intervention is necessary. The implemented advanced control strategy for comminution area consists of two layers in hierarchical structure. The lower layer objective is to stabilize the process stabilization using model based predictive controller (MPC) technique. The unique MPC used in this layer is called BrainWave™ chosen for its robustness, convergence and delay handling; furthermore, the developed platform offers stable and repeatable solution and has short implementation time. The upper layer is a supervisory control, which sends the preferred process operation points to the lower layer to drive the process towards optimal performance. The goal of this layer is to optimize the process targets, as well as making decision. To increase process performance, automatic ore characteristic adaptations are implemented in this layer. A digital twin of comminution area is built in the second layer that runs amongst the process in parallel. By communicating, the process data in real time, a virtual densitometer is built that is being used in our advance process control strategy. Our control strategy has been developed, tested and implemented in various areas of a copper concentration plant. The targets for implementing advance process control are usually increased throughput, decrease energy consumption and variability reduction in particle size distribution. Overall, the results showed in different mine sites are increase throughput between 2 and 5%, specific energy consumption reduction about 15% and process variability reduction up to 60%. In this paper we discuss the results of the recent implementation of this technology on Minera Los Pelambres, Minera Collahuasi and CAP Minería. Their concentrator plants have installed control systems with the most updates optimization features, for SAG mill, ball mills and thickeners.

Jan 1, 2019

By Paulo Cesar Pavan

T&T or Traceability, is a concept of generating, storing and on demand providing information about all traceable items in the supply chain

Jan 1, 2019

By M. E. Ryan, C. L. Hoebbel, E. J. Haas

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the official position of the National Institute for Occupational Safety and Health, Centers for Disease Control and Prevention. Mention of any company or product does not imply endorsement does not constitute endorsement by NIOSH. ABSTRACT It has been suggested that effective disaster prevention and response in mining requires that elements of emergency management be incorporated into everyday operations, planning, and decision-making, much in the same way that the industry approaches routine risk management. Since Congress passed the MINER Act in 2006, the newly mandated structural and technological advancements in mine emergency response preparation have been made and are apparent, but measureable improvement in mineworker emergency preparedness is difficult to ascertain. To begin exploring whether measurable indicators of mine workforce preparedness can or should be addressed within a risk management framework, NIOSH researchers examined the datasets from two separate research efforts—one which measured the organizational safety climate and self-reported safety performance, and the other which measured individuals’ perceptions of their own self-escape competency. INTRODUCTION In response to the mine disasters in 2006, the United States Congress passed the Mine Improvement and New Emergency Response Act (MINER Act), which strengthened existing regulations [30 CFR, Part 48] and introduced new provisions to improve mine emergency response. Since that time, new technological and structural features, such as mandated redundant communication systems, personnel tracking systems, and lifelines in primary and secondary escapeways, have been installed in underground coal mines across the country. Additionally, mine operators are required to develop emergency response plans, provide adequate supplies of breathable air throughout the mine, provide more frequent and realistic expectations training, and are required to immediately notify the Mine Safety and Health Administration (MSHA) in the event of an accident. While the structural and technological advancements in emergency preparedness are readily observable and easily measured, levels of individual mineworker preparedness remain difficult to assess. There is a general consensus that deficiencies in competence in the non-routine tasks required for individual miners to effectively respond to a mine emergency likely remain (e.g., National Research Council [NRC], 2013), and NIOSH research continues address this concern (Haas, et al., 2015; Hoebbel et al., 2018). To maximize an operation’s capacity to effectively prevent disasters and/or respond to emergency events, it has been suggested that individual and emergency management efforts be incorporated into everyday operations, planning, and decision-making in much the same way organizations manage routine risks to health and safety (Haddow et al., 2017). To the authors’ knowledge, the mindful intersection of routine risk management policies and practices and emergency prevention and response readiness have yet to be empirically studied within the mining industry.

Jan 1, 2019