Search Documents

By William G. Pariseau

The extraction ratio approach to pillar design in flat seams is based on a mathematically exact analysis that is a reasonable physical approximation to room-and-pillar layouts in many instances. The essentials of the approach are reviewed and then mathematically approximate formulas for pillar design in inclined seams of arbitrary dip are proposed. Detailed numerical analysis of stress about a typical 5 entry, 4 pillar panel at dips of 0, 15, 30, 45, 60, 75 and 90 degrees at low and high extraction ratios show that the proposed inclined seam extraction ratio formulas for pillar normal and shear stresses, although conservative, have an accuracy quite adequate for engineering purposes. Appropriate pillar safety factors for compressive and shear failure and a safety criterion for overturning are specified.

Jan 1, 1982

By R. C. M. van der Spuy

The heavy-minerals plant at the Palabora Mining Company treats 25 to 30 kt of new feed daily. The U3Og value of the ore averages approximately 40 p.p.m. The circuit consists of four stages of upgrading on 68 Reichert cones, fol. lowed by a jig and 30 table decks. The paper describes how feed-distribution problems have been overcome and the methods used for monitoring and controlling the cone performance. The adaptation of a standard jig for the recovery of fine minerals is discussed, and a method of 'table agglomeration, for the recovery of coarse refractory copper sulphide is described. The tables consist of polyurethane-covered fibreglass decks, and their operation is controlled according to measurements of the uranothorianite content of the concentrates and middlings by means of a nuclear scintillation counter. The upgrading ratio of the uranium mineral by gravity concentration is 1000:I, baddeleyite (ZrO.) being recovered as a by product.

Jan 1, 1982

By R. W. Boyle

"PREFACEThis paper comprises two parts. The first part discusses lithochemical surveys based on major, minor and trace elements in whole-rock samples from primary enveloping halos. The second part continues with discussions of surveys based on leakage halos, zonation of elements, stable and radioactive isotopic distributions, geothermometric, geobarometric, thermolumin escent, pedochemical, hydrochemical, atmochemical and biogeochemical methods. A selected bibliography follows the second part of the paper.ABSTRACTAreal (two-dimensional) geochemical surveys, based mainly on secondary dispersion halos and trains in media such as surface waters, soils and drainage sediments, have proven particularly successful in recent years and have greatly assisted in the discovery of a large number of varied mineral deposits. Three-dimensional surveys based on primary halos and leakage halos have received relatively little attention by research organizations and the mineral industry. Such surveys offer many novel approaches for discovering blind mineral deposits deeply buried below overburden or within their host bedrocks. This paper reviews detailed methods for the discovery of blind mineral deposits based on sampling rocks (lithochemical methods), soils and other types of overburden (pedochemical methods), waters (hydrochemical methods), gases (atmochemical methods) and biological materials (biogeochemical methods) . All are applicable to the discovery of blind deposits; the efficacy of each or in combination depends essentially on the type of mineralization, the extent of the development of the primary and secondary dispersion halos, and the finances available for sampling techniques employing overburden drilling, bedrock drilling, and sophisticated water, gas and vegetation collection."

Jan 1, 1982

By Mark S. Sanders

Based on laboratory tests and preliminary field tests of off-the-shelf steel toed rubber boots, a molded sole design was developed to provide increased traction over conventional calendared sole miners' boots. The pattern provided sharp edges perpendicular to both lateral and fore-aft slip vectors. The sole was designed to reduce mud caking. An instep lace-up capability was added to better secure the foot inside the boot. A five month field evaluation compared the prototype boots to the boots the participants usually wear. Although objective slip and fall data showed no significant advantage for the prototype, subjective evaluations made by the participants indicated increased traction for the prototype boots. Approximately 75 percent preferred the prototype to their own boot. Approximately one-third used the lace-up capability. It was concluded that molded soles provide better traction than calendared soles for the underground mining environment.

Jan 1, 1982

By M. Paczkowski

The use of inert gas systems to extinguish mine fires has been the subject of research for some time in the United States. In some European countries, it is an established practice. Tests were conducted with the CMI Inert Gas System (CMI), which is being used by the Polish mining industry. This system utilizes a modified jet aircraft engine and afterburner as a compact source of combustion products with a very low (less than one percent) oxygen content. Water injected into the combustion products stream provides evaporative cooling and forms a mist with a high cooling capacity. The CMI system was used under controlled conditions to extinguish coal pile fires at the U. S. Bureau of Mines Experimental Mine in Bruceton, Pennsylvania. The test results show that the CMI system can be used conveniently to extinguish fires quickly and to maintain an inert atmosphere in the fire zone to prevent re-ignition.

Jan 1, 1982

By Richard D. Miller

This Bureau of Mines publication contains analyses and related source data for 224 natural as samples from 18 States. Of the total, 191 sam¬ples were collected during calendar year 1981. The remaining 33 samples were collected during previous years, but releases, granting permission to publish were not received until 1981. All samples were obtained and analyzed as part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted since 1917. The analyses published herein were made by the mass spectrometer and special helium apparatus described previously (1-2).3 The results of the investigation of the occurrences of helium are published annually to make the information available as soon as possible to the gas industry and the general public. Twenty-five publications have presented the results of 12,827 gas analyses made prior to 1981. The first three bulletins (1-3) contain analyses and related data on 5,218 gas samples collected from 1917 through 1960; these bulletins have been supplemented annually by information circulars (4-17, 19-24) containing 7,609 analyses of samples collected since 1960.

Jan 1, 1982

To evaluate the potential for dust reduction, during blasthole drilling, of water or foam applied directly into the drill hole. Approach The Bureau of Mines tested a through-the-drill-steel water and foam injection technique in two noncoal mines to evaluate the method's potential for greater dust reduction. The tests were performed by drilling a series of blastholes for an entire face (a 90 minute time-period). For the first 45 minutes of drilling, foam or water was applied through the drill steel. Blowing ventilation was supplied to the entry about 50 feet from the face. The dust concentration measurements were made by a Real-Time Aerosol Monitor (RAM-I), and the data were read out on a strip chart recorder. The evaluation test results showed that the water or foam injection technique, when used on localized dust sources, can be an extremely effective dust control method. Small amounts of water used in this method have also allowed it flexibility to be used in water-soluble ores such as salt, gypsum, anhydrite, and trona. How The System Works Water or foam is mixed with compressed air (approximately 100-120 psi) with suitable metering systems and forced through the drill steel into the blast hole at the point of dust generation. Because the water or foam is applied at the source, minimal quantities of liquid are needed (0.2 to 0.6 gpm). These low flowrates are sufficient to just moisten the dust emerging from the blast hole, thus eliminating a major source of airborne dust. The wet drilling procedure also eliminates a second source of dust. With dry drilling, the dust from the blast hole falls to the floor. Since this can be a 15-ft drop or more, the impact can send the dust billowing up from the floor, adding to the airborne dust. With wet drilling, the moistened dust merely dribbles down the face.

Jan 1, 1982

By Frederick H. Raab

A power-line proximity-warning (PLPW) system must have a high probability of detection (alarm activation at a specific distance), low probability of false alarm, and minimal set-up and maintenance. Tests of electric-field sensors have not demonstrated a dependable alarm distance. Alternative sensing methods such as microwave radar, optical radar, and sonar can meet the requirements by direct measurement of the range from the boom to the power line. Suitable microwave techniques include RF pulse, chirp FM/CW, and baseband pulse. Baseband-pulse radar has adequate range capability and does not require expensive microwave components. The radar cross section of a power-transmission cable is adequate for its detection optical-radar systems based upon LEDs and photodiodes are inexpensive, but can achieve only marginal performance in this application because of their limited modulation bandwidth. Since laser diodes and cryogenically cooled photosensors must be used to achieve the desired range resolution, the cost of an optical-radar system is greater than that of a microwave radar system. Sonar systems are feasible, but are not as precise and cost at least as much as baseband-pulse-radar systems. The performance of both optical-radar and sonar systems is degraded by dirt, necessitating the inclusion of a "windshield wiper.' Baseband radar appears well suited to the PLPW application. The cost of a baseband-pulse radar PLPW system is expected to be comparable to that of an electric-field PLPW system. Development and testing of an experimental model are therefore recommended.

Jan 1, 1982

By A. D. S. Gillies

Loss of visibility due to the occurrence of atmospheric fogging in underground mine airways can lead to a reduction in travel times and loss of production efficiency, an increase in the frequency of vehicular and foot traffic accidents and difficulty in checking rock surfaces for instability and loose material. Where hot and humid surface air meets colder underground air, conditions for fog formation nay be present. Further, suspended particulate matter from diesel exhausts or stoping operations together with slow movement of air along passageways nay contribute to formation. The study describes an investigation being undertaken with the cooperation of Kennecott's Ozark Lead Company to identify causes of the problem.

Jan 1, 1982

By Bernard L. Merlo

INTRODUCTION Modern mine management is constantly striving to develop improved mining methods which will not only increase productivity, but will also provide a safer work environment and make the most efficient use of our natural resources. Progress can be seen in this area by tracing mining methods through history. Work that was originally done with hand tools progressed with the age of mechanization to conventional mining, matured to continuous and longwall mining, and the advent of short¬wall mining, a combination of continuous and longwall, has recently been seen. This new method of shortwall mining provides a promising method for safe and ex¬pedient coal extraction. This study focuses upon the planning, design de¬velopment, and operation of the first producing short¬wall unit in the US which was operated in the Pittsburgh coal seam in northern West Virginia. MINE DESCRIPTION The mine is located in northern West Virginia at Grant Town in the heart of the high volatile Pittsburgh coal seam. Originally opened in 1901, the mine has be¬come one of the largest in the US, encompassing an area of approximately 103.6 sq km (40 sq miles). The seam being mined was the high volatile Pittsburgh seam which ranged in thickness from 1.8 to 2.96 m (6 to 91/2 ft). Three types of mining methods were employed: con¬tinuous mining, longwalling, and shortwalling, with each type accounting for 50%, 30%, and 20% of total pro¬duction, respectively. A total of 630 contract and super¬visory personnel were employed to produce the mine's designed annual tonnage of 1.8 Mt (2 million st). There were ten producing sections, eight continuous miners, one longwall, and one shortwall, operating a total of 22 unit shifts per day. Eight shafts, varying in depth from 80.2 to 194.2 m (263 to 637 ft) provided entrance to the Pittsburgh coal seam. These shafts were used for ventilation, portaling, coal hoisting, supply, and emergency escape hoisting. Ventilation was achieved by means of three exhaust fans which provided 707.9 m3/s (1.5 million cfm) of air to the mine and removed approximately 141 584 m3 (5 mil¬lion cu ft) of methane per 24 hr period. The room-and-pillar method was used for secondary recovery with designed barrier blocks between panels of 61 m (200 ft) in width. A double row of blocks was left around each gob area to provide efficient bleeder action

Jan 1, 1982

By S. V. Burr

"IntroductionOne of the more puzzling geological enigmas, in the writer's opinion, is how rock can move sideways with respect to other rock. In the writer's study of regional northwest-southeast folding in North America (Burr, 1980), he may have found the answer to horizontal offset.Horizontal OffsetSideways movement or horizontal offset does not mean that the movement was, or is, horizontal. As indicated below, the actual movement may be at a high angle from the horizontal. However, it is the horizontal VECTOR, or offset, which is measured on surface by geologists. Vertical movements (thrust, normal, reverse) can be understood, as they involve blocks of rock , generally separated on four to six sides, which have been pushed up or subsided. Vertical faulting across dipping strata can produce APPARENT horizontal offsets. However, this thesis deals only with ACTUAL offsets.The ProblemFigure 1 is a plan view of a simple hypothetical horizontal offset. Three vertical dykes are intersected by a fault lineament. Two dykes exhibit no movement; the middle dyke has been offset a distance (a). Vertical faulting would have produced no horizontal offset. How can a horizontal distance (a) disappear or appear? Rock expands or contracts in infinitesimal amounts.SolutionThe map (Burr, 1980) shows the writer's interpretation of regional northwest-trending folds in Ontario. The writer made two observations about horizontal offsets during his thirty year study of these folds:1) All major horizontal fault lineaments strike at a high angle to the northwest fold axes. Many of the northwest-trending lineaments are fault s, but their movement is essentially vertical.2) Close to many of the known horizontal offsets (and several lineaments), there are areas where plunge reversals are so frequent and close together it is impossible to draw in all the fold axes at a scale of 1 inch = 4 miles, and, in the highly faulted Espanola area southwest of Sudbury, Ontario, all the indicated folds cannot be easily separated at a scale of 1 inch = 1 mile. The writer has observed folds less than 30 feet apart next to the strong Puskitamica-Chibougamau fault in northern Quebec."

Jan 1, 1982

By Rustu S. Kalyoncu

A major goal of the Bureau of Mines is to conserve the Nation's mineral resources by developing improved performance materials. In support of this mission, a survey of the state of the art of chemically bonded refractories has been made, covering the scientific literature, government reports, and patents. This review includes research and development results for phosphate, silicate, oxychloride, oxysulfate, and other bonding agents used in refractories manufacture. A significant finding of the review was that references on bonding mechanisms, bond formation kinetics, and other important process parameters and conditions were few and universally vague. As a result, recommendations are made to expand research efforts to investigate the kinetics and mechanisms of reactions in chemically bonded refractories.

Jan 1, 1982

By Patzen Wu

Taiwan is located in the orogenic belt of island arcs on the western rim of the Pacific Ocean. The structure of the Taiwan coal fields is much complicated as a result of active Cenozoic orogenic disturbance in Plio-Pleistocene time. The abundant faults and folds have created poor structural conditions of the coal seams and some peculiar safety problems in mining however, the domestic coal still played an important role in the economic development of Taiwan for the years before 1968. Because of increasing mining depth and a decreasing number of miners, the coal production dropped from nearly 5.1 million metric tons in 1968 to 2.45 million metric tons in 1981. There were 173 small active coal mines and about 22 thousand miners in 1981. The coal mining in Taiwan has a history of more than one century. Specific efforts have been undertaken in solving major coal mine safety problems such as gas outbursts, bad roofs and weak floors, difficulty in ventilation due to deep underground mining, spontaneous combustion etc. We have thus acquired much helpful experience which, we deem, is worth reporting at this meaningful meeting.

Jan 1, 1982

By Kiran B. Chaudhuri

The Kivcet process is technologically the most advanced of the new lead smelting processes which have been developed over the past decade construction of the first commercial scale Kivcet lead smelter which has been designed by KHD Humboldt Wedag for Sociedad Complejo Metalurgico de Karachipampa is at present nearing completion in Bolivia. Some of the measures taken to minimise emission of harmful elements as well as methods employed to minimise energy consumption in the design of the smelter, are presented. Results of recent testwork which have added to the flexibility of the process are summarised.

Jan 1, 1982

By Charles E. Mann, Douglas J. Lootens, Rufino B. Bomasang

INTRODUCTION The economy of the Philippines, like that of many other developing nations, has been severely strained by the rapid escalation of imported crude oil prices over the past decade. In an effort to reduce its dependence on imported crude, significantly increased emphasis, both in the public and private sectors, is being placed on the rapid development of Philippine coal resources. This paper is designed to present an overview of the Philippine coal industry, its historical development, present status, and future potential. COAL RESOURCES AND RESERVES In 1977, a British consulting firm collated all available data on Philippine coal resources and estimated the total coals potential at about 0.9 to 1.4 billion metric tons (mt). In 1981, using more recent data the Philippine Bureau of Energy Development (BED) estimated the potential at 1.7 billion mt. The BED estimated the proven coal reserves at 257 million mt. These coal resources are scattered throughout the major islands comprising the Philippine archipelago. However, about 52 percent of the currently proven reserves are located in the tiny island of Semirara between the islands of Mindoro and Panay. About 25 percent is located in the Cagayan Valley in northeastern Luzon while 13 percent is located in Mindanao. The remaining 10 percent is scattered in the islands of Cebu, Samar, Mindoro, Negros, Polillo, Batan, and Catanduanes. The bulk of Philippine coal is sub-bituminous in rank. Some bituminous coal with coking properties has been reported in Malangas, Zamboanga del Sur in western Mindanao, and in Catanduanes, but the exact tonnages have not been accurately established. It is believed, however, to be at most 5 million tons. A little semi-anthracite coal exists in Malangas with the remaining unmined reserves estimated at a little more than one million tons. Table 1 shows the quality ranges of Philippine coal deposits.. Figure 1 shows the distribution of known Philippine coal resources PHILIPPINE COAL PRODUCTION In 1981, total coal production was 330,720 mt. Though modest by world standards, this was the highest production figure in Philippine coal mining history. This came from 25 mines, mainly small scale underground mines of capacities varying from 10 to 100 tons per day (tpd). The actual production capability was about 800,000 mt in 1981, but the producers had to scale down production to the level of local demand. Even then, some 50,000 tons of coal remained unused by year-end. The 1981 production came from the following areas: Cebu 224,751 mt (68%) Zamboanga del Sur 57,095 mt (17%) Semirara 13,222 mt (4%) Polillo 17,132 mt (5%) Cebu has always been the main source of Philippine coal production. Coal mining has been carried out in Cebu for the last 50 years, although it has been characterized by a very crude mining technology. Due to the limited size of coal deposits and complicated geology, however, Cebu's share of the total national production is expected to go down to only 10 percent by 1985. Except for Semirara's open-pit production, the balance of Philippine coal production comes from underground mines. These underground mines generally use room-and-pillar methods, except for those at Zamboanga del Sur and Polillo which use modified longwall methods patterned after those used in Taiwan. Due to the much higher mining recovery, most underground mines are now planning on switching to longwall. At Semirara, an open pit mine is now being developed for a one million ton per year capacity by 1984, and will then be the largest Philippine coal mine. While present earthmoving work is done with bulldozers, loaders, and trucks, the main coal extraction equipment will be bucket wheel excavators imported from Austria. PRESENT COAL UTILIZATION Existing coal production is sold mainly to coal- fired cement plants and power plants. The balance is sold to a sugar central, a coconut oil mill, a food processing plant, and two plants producing carbide and ferro-silicon alloys.

Jan 1, 1982

To find solutions for common safety problems encountered in the handling of trailing cables, based on observations at many different surface mining operations. Approach Practices in handling trailing cables were Investigated through personal visits to over 40 mines, supplemented by visits to cable manufacturers and cable repair service companies. The most effective solutions to the safety problems en-countered were noted and are described In the project final report. Examples are given in this Technology News. Accident Experience Most cable-related injuries occur as a result of workers lifting, pulling, tripping, or being struck by the cable. The Table gives the frequency of occurrence for injuries reported during a recent 3 1/2 year period.

Jan 1, 1982

By Kim B. Shedd

The U.S. Bureau of Mines Particulate Mineralogy Unit examined the habits of six zeolite minerals commonly occurring in domestic zeolite deposits. Mineral habit is of interest because current theory on the potential for sarcoma production in test animals emphasizes the size and shape of mineral particles, without regard to composition or structure. A scanning electron microscopic study revealed that, of these six minerals, only mordenite and erionite crystallized in acicular to fibrous habits, The fibrous varieties of these two minerals were characterized by size and shape on the transmission electron microscope, and their dimensions were compared with those of asbestos and amphibole cleavage fragments. When comminuted, these two minerals possess "fibrosity indices" similar to those of amphibole cleavage fragments. One sample, a rare woolly erionite, has uniform widths, large aspect ratios, and a "fibrosity index" similar to those of asbestos.

Jan 1, 1982

By Jim F. Lemons

The Bureau of Mines Minerals Availability System collected and analyzed data for 34 nonlaterite and 9 nickeliferous laterite domestic chromite deposits in order to assess their viability as sources of chromium under present technologic and economic conditions. These 43 deposits, none currently in production, contain approximately 6.3 and 22.3 million metric tons of Cr203 at the demonstrated and identified resource levels, respectively. Approximately 4.6 and 15.6 million metric tons of Cr203 are recoverable at the demonstrated and identified levels, respectively, for the 34 nonlaterite deposits. None of these resources are economically recoverable at January 1981 market prices. Production of metallurgical-grade chromite (market price $128 to $144) would require a minimum chromite market price of $237 per metric ton. Chemical-grade chromite production (market price $74 to $85) would require a chromite market price in excess of $188 per metric ton. From the 34 nonlaterite deposits, roughly 5.4 and 17.6 million metric tons of ferrochrome could be produced at the demonstrated and identified resource levels, respectively; however, a minimum market price of $770 per metric ton of ferrochrome would be required to stimulate production. The nine nickeliferous laterite deposits were not evaluated through production stages because of uncertainties in process technology and cost.

Jan 1, 1982

By Ann G. Kim

Acid drainage from underground coal mines and coal refuse piles is one of the most persistent industrial pollution problems in the United States: This Bureau of Mines report reviews the acid mine drainage problem generally and describes research currently underway to combat it.

Jan 1, 1982

By K. H. Nimerick

Froth flotation of coal is growing in importance and complexity. Some of the reasons for these changes follow. 1) A need exists for energy resource conservation. 2) Preparation plants are processing widely varying coal -- deep seam, strip and stockpiled either separately or as blends. 3) More fines are being generated because more mines are using automatic mining equipment. 4) It is more practical and economical to remove ash and sulfur at the preparation plant than during utilization.

Jan 1, 1982