Search Documents

By J. P. Mogan

As diesel exhaust contains a mixture of several materials of varying degrees of toxicity which interact to a currently undefined extent in their effects on health, the prescription of a quantity of ventilating air to dilute the exhaust to a safe level is necessarily, to some extent, arbitrary. Some jurisdictions rely on the application of a safety factor to a single "governing" component (usually nitric oxide for most modern diesel engines). Others specify that the total of the "adjusted" concentrations (actual concentration divided by maximum permissible concentration) not exceed "one" for related constituents (irritant gases for example). Neither of these approaches, however, takes account of the interaction of the gaseous constituents with diesel soot (although many studies verify such interactions), nor do they provide any economic incentive for reducing pollutants which are not included in the criteria for ventilation. Because of these factors, the Canadian Department of Energy, Mines and Resources awarded a contract for a study of the current literature bearing on the "Health Implications of Exposure of Underground Mine Workers to Diesel Exhaust Emissions" (1). One goal of this study was the formulation of a new ventilation criterion. The contractors, Ian W. French and Associates, studied more than 1500 literature citations which they interpreted in a 350 page report and summarized in a companion 1600 page annotated bibliography. In the recommendations section of the report, they defined a new 'health effects index' or ventilation criterion "V" as follows: [ ] The contractors consider that a "V" between 3.0 and 4.0 poses a moderate threat to health which could be alleviated by the use of protective equipment such-as filter helmets. If V exceeds 4.0, an increase in ventilation quantity to reduce the pollutant levels is indicated. In the case of mines with a quartz content in excess of 20% in the ore, the contractor recommends that a term. [Quartz]/ [Threshold Limit Value Quartz] be added to the equation, and [2.0 = ?v? = 30] be the range justifying protective equipment, with added ventilation if "v" exceeds 3. A degree of pragmatism was inherent in the development of the equation, as the contractors recognized that the components of the index, if it is to be useful in the near term, should be within current routine underground environmental assay capability.

Jan 1, 1980

By R. V. Ramani, G. W. Luxbacher

The approach proposed in this paper is, as stated by the authors, an update of methods well discussed in the literature. The authors are to be congratulated for their excellent effort in quantifying a difficult problem with realistic cost data. Economic analysis of the components of a mine ventilation system is complicated by both the dynamic nature of the system and the uncertainty as to the time when system changes occur. We wish to address three specific areas of this paper which require further consideration: shaft designed air capacity, shaft location, and economic criteria used within the analysis. With regard to ventilation shaft size optimization, the system complexities are illustrated in the quantity flow through the shaft. Obviously, the capacity chosen by the designer is a static parameter while the utilized capacity is usually a dynamic variable over the life of the shaft. The designed capacity may be used for a short or a long period, and this may occur during the beginning, middle, or near the end of the shaft life, leading to different operating costs at different times. Operating costs, as shown by the authors' Eq. 8 are more dependent on air quantity than any other single factor (quantity cubed as compared with other factors to the single power); hence, extreme accuracy in the assessment of some of the other factors discussed by the authors may be secondary to the quantity estimation. Incorporation of a variable usage factor for air quantity over the life of the shaft in this optimization problem deserves some consideration. Although the authors have chosen to examine optimum ventilation shaft sizing, it must be remembered that optimization of the whole system-is the primary objective of any optimization process; unit optimization of such items as shafts may not complement the overall process. We have discussed this subject in some detail in another paper in this Transactions volume (Luxbacher and Ramani, 1979). While the recommended process by Wang, et al. can be used in shaft sizing, the shaft operating conditions (pressure head and air quantity) are intertwined with the shaft location within the mine infrastructure:

Jan 1, 1980

By Donald R. Simon

Money... not many subjects are as personal or as emotional. Hessiod said it well in 700 B.C. "Money is life to us wretched mortals". Are you getting paid enough? Does your company reward its top people? Does coal or copper pay more? Production or engineering? How is the synfuels industry going to influence mining salaries? Do high salaries attract and retain the best people? Do modern compensation systems ensure fairness or destroy entrepreneurial spirit? With our tax system and high standard of living why are we so salary conscious? Salary is not only important for what it can purchase but it is also a yardstick, measuring how well we are doing. We all need money to pay the bills and maintain our standard-of-living, but once we reach a certain point the psychological ramifications become more important than the purely practical side. Even necessary payments like the mortgage and the car are a function of our egos. Are our choices of cars and homes based on simple transportation and shelter?

Jan 1, 1980

By James A. Morgan

FIELD MEASUREMENTS OF NOISE WERE MADE ON THE PERIPHERY OF ENCLOSURES DESIGNED, MANUFACTURED AND INSTALLED BY INDUSTRIAL ACOUSTICS COMPANY, INC. ON THE SECONDARY TACONITE CRUSHER AT THE JACKSON COUNTY IRON COMPANY PLANT IN BLACK RIVER FALLS, WISCONSIN. NOISE REDUCTION ACHIEVED BY THE ENCLOSURES WAS SUFPICIENT TO PERMIT REDUCTION OF CRUSHER ROOM NOISE TO 90 DBA, PROVIDED THAT OTHER SOURCES ARE APPROPRIATELY TREATED AND ACOUSTICAL ABSORPTION IS PROVIDED IN THE CRUSHER ROOM. SECONDARY CRUSHER NOISE WAS REDUCED 10 TO 15 DBA BY THE ENCLOSURES.

Jan 1, 1980

By C. K. Lee

This Bureau of Mines report presents results from experimental studies on wood fires in a laboratory-scale tunnel network. Experimental measurements include ignition delay time, flame spread rate, ventilation air and gas flow rates, wood temperature, gas temperature, pressure and composition, thermal flux, and smoke particulates. These measurements form a data base for fire-scaling studies and provide information on various fire processes, such as flow interaction between ventilation air and fire, fire throttling and reverse flow, and duct fire energetics. Results show how hazards of duct fires relate to the development of (1) asphyxiating and toxic fumes, (2) explosive gas mixtures, (3) throttling of ventilation air, and (4) high-temperature combustion products. Such fire hazards should be carefully considered when testing flammabilities of materials used in a confined underground mine environment.

Jan 1, 1980

By J. P. Hansen

In order to help assure an adequate domestic supply of minerals essential to the Nation's economy and and security by developing more efficient minerals extraction technologies, the Bureau of Mines Tuscaloosa Research Center examined the application of autogenous microgrinding to calcium carbonate minerals. Treatment of minus 8-mesh Alabama marble resulted in a product 80 pct minus 5 micrometers (µm) at a power consumption of 70 to 80 kwhr/ton, This study shows that coarse particles of calcium carbonate minerals are effective as the grinding media for the autogenous attrition grinding of these minerals. The minus 8- plus 30-mesh fraction is an effective grinding medium (sand) for particles smaller than 30 mesh. A 40-pct-solids slurry and a sand: marble ratio of 2.5 appeared to be near optimum. For residence times above 13 minutes, products were greater than 80 pet minus 5 µm and greater than 54 pct minus 2 µm. Power consumption was uniformly low, ranging from 50 to 100 kwhr/ton of product depending upon the feed rate. One marble sample from Georgia was shown to be the most persistent grinding medium, with losses of less than half those of the other materials tested.

Jan 1, 1980

By Torckler L, Brathwaite R. L

At Neavesville gold-silver (electrum) mineralization occurs in steeply-dipping zones of intense fracturing, brecciation and quartz veining within rhyolitic pyroclastics, carbohaceous shales and andesites. Hydro- thermal alteration extends over an area of greater than 3 by 1.5 km. In rhyolitic tuffs, highly silicified zones containing quartz- adularia-illite assemblages are flanked by less silicified assemblages composed of albite, illite-montmorillonite and chlorite. The mineralogy ana sequence of alteration are comparable with the alteration zones which envelop the steam-producing fissures of the active Wairakei and Broadlands geothermal fields. Primary fluid inclusions in quartz from five fissure veins in the Neavesville field show maximum homogenisation temperatures ranging from 220 - 260¦C and salinities of 0.0 - 1.1 wt. % NaCl equivalent, which cover a similar range to actual measured temperatures and salinities in geothermal fluids at Wairakei aria riroaolan¦s. The age of the rhyolitic pyroclastics and related alteration and mineralization is probably Pliocene and Neavesville therefore represents a fossil geothermal system.

Jan 1, 1980

By R. D. Stewart

Abstract. Induced fluorescent sorting is a means of beneficiating an ore by selective labeling with a reagent combination which fluoresces when activated by ultraviolet light The reagent combination normally consists of a surface active compound and a fluorescent dye. The surfactant adheres selectively to a specific surface and carries the dye with it. Upon activation with ultraviolet light, the labeled pieces, in the size range 1.27 cm to 20 cm (0.5 to 8 in.), are detected during free fall by photosensitive cells and ejected by water jets. Either ore or gangue may be labeled.

Jan 1, 1980

By Radoslav Despotovic

The developed radiometric method of particle system analysis has been applied to investigate the bulk properties of particles precipitated from solutions. The nature and principles of the method applied are described briefly, and some possible models in the field of fine colloid particles precipitation discussed. Changes in radionuclide distribution were followed during the solid phase formation and the data were used to calculate changes in bulk composition of colloid precipitates. The radiometric data show interesting phenomena closely connected with the characteristic of bulk particles. The measured radiometric data are highly reproducible, the applied methods have proved to be sensitive, and the developed techniques have been tested by various standard procedures.

Jan 1, 1980

By Steven R. Ruggieri

This report documents the work performed and the results obtained during the field demonstration of the Remote Sealing System at the USBM's Jenny Mine near Inez, KY in the Fall of 1978. Although various portions of the Remote Sealing System had been used on a number of prior occasions, the field demonstration at Jenny Mine marked the first use of the complete upgraded system including the use of the inert gas generating system for seal placement and the first application of the new froth foam system. The objective of the field demonstration at Jenny Mine was to demonstrate the complete system by emplacing and evaluating several complete underground seals under conditions representing those of a mine fire situation. Several critical sealing conditions were identified including: ? High entry airflow ? Standing water (1 to 2 ft) in the entry ? Flowing water (150 gal/min) ? Irregular roof ? Sealing a 4-way intersection. Four seals were successfully placed under the conditions mentioned above. The demonstration served to verify proposed techniques to handle these conditions as well as to dispel any doubts about the system's capabilities. As a result of the successful field demonstration, the Remote Sealing Equipment is now under the jurisdiction of MSHA's Mine Emergency Operation ready for a mine fire emergency.

Jan 1, 1980

By Jr. Abel

Subsidence is controlled by a complex combination of mining and geologic factors. For example, a world-wide compilation of data shows that, as the percentage of shale in the overying rock mass decreases and the amount of sandstone increases, the angle of draw (and the area affected by subsidence) decreases. Limestone in the overburden appears to cause as much as a three-fold decrease in the angle of draw compared to a like amount of sandstone. Increased amounts of sandstone were accompanied by a greater surface subsidence relative to the mining height. The total thickness of overburden did not appear to influence the subsidence magnitude above super-critical panels. The greater the thickness extracted the smaller percentage of that thickness that shows up at the surface as subsidence. The greater the percent of the seam extracted, the greater the subsidence reaching the surface. The maximum subsidence above room and pillar panels is dependent on the pillar height and minimum width as well as the other factors listed.

Jan 1, 1980

By John Durkin

A system based on seismic techniques has been developed to detect and locate men trapped underground following a mine disaster. Both theoretical and field studies have been used to generate models to predict the performance of the system. For a strong source, it is almost certain that the miner's signal will be detected if the geophone array can be positioned over a likely area of entrapment. After signal processing, it is highly likely that the location of the miner can be determined within an accuracy of 100 ft (30.5 m). The system is presently operational in a state of readiness in the event of a mine disaster.

Jan 1, 1980

By K. O. Bennington

The thermodynamic properites of petalite (Li2A12Si8O20) were determined by the Bureau of Mines. The enthalpy of formation was determined by hydro-fluoric acid solution calorimetry. The values from the elements and from the oxides are ?Hf°298.15 = 2,335.8 ± 3.0 kcal/mole and ?H°295 (from oxides) = -50.60 ± 1.20 kcal/mole. Low-temperature heat capacities were determined by adiabatic calorimetry from 10.69 to 302.11 K. The derived standard entropy is S°298.15 = 111.0 ± 1 cal/deg-mole. Enthalpy increments above 298 K were measured by copper block calorimetry from 298 K to 1,193.6 K. The various experimental data were combined with other data from the literature to calculate the Gibbs energies of formation and equilibrium constants of formation over the temperature range of the measurements. Tables of enthalpies of formation and Gibbs energies of formation are given as a function of temperature from the elements and constituent oxides. The Gibbs energy of formation is ?G°f298.15 = 2,203.8 kcal/mole.

Jan 1, 1980

By John F. Martonik

When OSHA came into existence in 1970, it adopted national consensus standards to improve safety and health conditions in work places. Coke oven emissions, which are proven to cause cancer and respiratory diseases, were regulated by the coal tar pitch volatile standard, adopted from the 1969 edition of the Threshold Limit Values for Airborne Contaminants by the American Conference of Governmental Industrial Hygienists. The coal tar pitch standard, based upon the benzene soluble fraction of total particulates, limits the personal exposure to 200 micrograms of the benzene soluble fractions of total particulate per cubic meter of air. This standard can be classified as a performance standard because only general limits are set which allows the employer to choose for themselves the means to comply. Both the United Steelworkers of America and the American Iron and Steel Institute petitioned the Secretary of Labor to write a new standard for coke oven missions, each thinking the coal tar pitch standard unsatisfactory.

Jan 1, 1980

By F. J. Zuiderweg, G. G. Bemer

Results of a study aimed at assessing kinetics and mechanisms of the batch agglomeration process in suspension are discussed. A recently developed light backscatter technique which enables the increase of average particle size from 1 to 5000 µm to be followed, was used to determine agglomeration kinetics. Growth curves and agglomerate size distributions were obtained in a stirred vessel for various model systems and operating conditions. Four distinct growth regimes were identified, i. e. the flocculation regime, the zero-growth regime, the fast growth regime, and the equilibrium regime. Further, it was observed that large differences in the occurrence and duration of these regimes resulted from small variations in parameters, such as size distribution of the initial particles and the binding-liquid to solid ratio. Mechanisms that determine the occurrence of the relevant regimes are discussed. The growth process was described in terms of population balance equations. In this way, the growth rate, the equilibrium agglomerate size distribution, and the evolution of the agglomerate size distribution were generated. The agreement with experimental results is satisfactory.

Jan 1, 1980

By G T. Kukla

A Seam deposit User oriented Mine Planning System (SUMPS) was developed by The Broken Hill Proprietary Company Limited (BHP) at its head office in Melbourne. It is one of the computer mine planning systems developed by the Corporate Data Processing (CDP) section of BHP. To date it has been employed in the feasibility study of four coal prospects for the BHP Group, including Gregory in central Queensland û Ham and Van Hoorn (1978). It was also used in detailed short term mine planning for Gregory. A recent application was in the feasibility study of Saxonvale, a multi seam coal deposit in New South Wales with seams up to 20 m thick. The other two applications of SUMPS were also on thick multi seam coal deposits. Development of programs for the underground subsection of SUMPS is continuing. SUMPS was developed and implemented on mini computers with graphics and plotting peripherals. The company's philosophy towards computing is one of centralized development and project planning, with transfer of hardware and software to site once the mine becomes operational. Support of the site's system continues from head office which is continually involved in development of SUMPS and issuing revision updates to sites. The users, as well as programmers, were mostly geologists and mining engineers. This helped to ensure rapid, successful implementation. The broad approach of this system was to use interactively the specialist skills and interpretative abilities of the user mining engineers and geologists with the data manipulation abilities of the computer. It is an integrated system which covers geological exploration, deposit modelling, mine planning and production scheduling. An important feature of the system is that the user has full interactive control over each function through a graphics terminal where applicable.

Jan 1, 1980

By Donald Whittaker

Severe climatic conditions in mines are normally associated with working at depth. More precisely, it is a matter of working in regions of high strata temperature, since, for example, some coal mines in the Ruhr have strata temperatures at 1000 m which are matched only at 3 times that depth in the South African gold mines. In Britain we are perhaps fortunate in encountering strata temperatures in our deeper coal mines some 10-15 K lower than at the same depth in the hot mines of the Ruhr. Nevertheless the problems of high temperatures and humidities in UK mining operations, which in the past have been confined to a few specific sites, have in recent years become more widespread, and there is every reason to suppose that the trend will continue. Clearly strata temperature is not the only .causative factor. Long ventilation circuits serving districts remote from the shaft must also play a part, while the heavy use of machinery and the rapid, rates of excavation of modern mining methods are obviously important. It is necessary to understand the mechanisms of all such factors, and to measure their magnitudes and fluctuations, if remedial measures are to be properly designed or predictions made which are accurate enough to be of use in ventilation planning. This paper presents the results of a long-term (and continuing) investigation carried out in several mines to measure the major sources of heat and moisture on longwall districts and trunk conveyor roadways. The variation with time of these sources is reported, and the resultant effect on the climate is considered. In their investigations of the heat exchanges occurring in a whole mine Oakes and Hinsley (1955-56)1 listed and estimated the magnitudes of a large number of heat sources. Some of these, namely autocompression of the air in the shaft, diesel engines and compressed air mains, do not apply to the present investigations, which refer to longwall districts with conveyor transport and no compressed air supply. Others, such as oxidation of coal and, desorption of methane, have not been taken into account in the measurements, but are discussed later. One other source, the importance of which was pointed out by Gracie and Matthews (1975)2, is the coal on the conveyor, a form of strata heat emission, but one which is strongly dependent on the rate of coal production. The heat emissions measured in the present investigations were the energy consumed by electrical machinery, the heat conducted from the strata and the heat lost by the conveyed coal. Most of the emitted heat was removed from the district by the ventilation air, and was measured by continuously recording the enthalpy of the air at fixed stations. The heat removed by service water, supplied for machine cooling and dust suppression, was also measured. Account was of course taken of the relatively minor changes in level around the districts, in terms of the potential energy gained or lost by the coal and by the ventilation air (autocompression).

Jan 1, 1980

By Lorne Sivertson, Peter Kitrredge

"World metallurgical coal imports totalled 110million tonnes in 1978. Of this amount, Japan imported 50 million tonnes, making it by far the largest and most important coking coal market . British Columbia and Alberta exported 12.0 million tonnes of coking coal in 1978, or 11% of the world total. Virtually all of these exports were directed to Japan, making up 22% of total imports.Some observers have suggested that because Japan is almost the exclusive buyer of British Columbia and Alberta metallurgical coal, the benefits of the coal trade may be primarily on the side of the powerful Japanese buyers. Buttressing this suspicion is the fact that Japanese trading companies have taken substantial equity positions in B.C. coal mines, thus presenting the possibility of non-arms-Iength transfer arrangements. There is then at least some evidence to support the hypothesis that Canada's western coal producers receive prices that are less than would prevail in a more competitive market; that is, that they are exploited.This paper produces evidence that Canada's coals are not underpriced in respect to U.S. and world markets. The conclusion is drawn that British Columbia and Alberta metallurgical coals receive prices that are equal to prices known to be competitively determined. This conclusion follows an in-depth analysis of prices, coal qualities and the economic characteristics of all major coals traded in the Japanese market. A by-product of the analysis is an equation capable of predicting the value of any metallurgical coal sold to Japanese buyers, or, for that matter, any buyer. Hopefully, this can be of some use to coal producers in developing their marketing strategies."

Jan 1, 1980

By Cocquio D. S, Bauchau C

In the course of an integrated airborne survey in 1975, a uranium-molybdenum deposit was discovered by Minatome Australia Pty Limited in North Queensland, Australia, approximately 70 km by road west of Townsville.The mineralization occurs in a welded tuff unit within the Carboniferous St James Vokanics. It is structurally controlled by a complex of subvertical east-west fractures and is exposed over a strike length of 350 m. Drilling has traced a further 150 m extension underneath a barren capping consisting of a thick pile of vokano-sediments. The maximum width of the orebody is 150 m, and its vertical thickness is approximately 100 m.The primary ore minerals are coffinite, pitchblende and molybdenite, accompanied by various alteration products (particularly uranium molybdates).The vein-type mineralization is considered epigenetic.A comprehensive program of surface drilling and underground exploration is in progress to establish the uranium and molybdenum reserves.

Jan 1, 1980

By K. P. Bingham

Lime is one of the largest volume chemicals produced in the United States. In 1979 approximately 21 million tons were produced. Lime is, in fact, second only to sulfuric acid as the largest volume basic chemical produced. Lime, also known as quick lime (calcium oxide) and hydrate lime (calcium hydroxide), is the principle alkali used in a multitude of industrial processes. In addition to its use as a principle industrial alkali, lime has experienced dramatic growth in four general market areas during the past 30 years. These four areas are: 1. Water Treatment - Lime is used extensively in treating and purifying water for industrial and potable use, Although significant tonnage is shipped to this market of municipal and industrial water treatment plants, the end-users are widely spread geographically and individual shipments are relatively low tonnage. Lime, which is nonhazardous, can safely be shipped by truck or rail to these small end-users. 2. Municipal and Industrial Waste Treatment - Environmental agencies at all government levels,

Jan 1, 1980