Search Documents

By John E. Miller

In recent years there has been increasing concern in the mining industry over the availability and high cost of diesel fuel to support mining operations. Unit Rig & Equipment Co. has been deeply involved with the development and testing of the newest designs for trolley assist. Beginning in dune 1980, Unit Rig modified and commissioned six 156 metric ton (170 short ton) trolley assist haulage trucks at two mine locations in South Africa. Operating haulage trucks with General Electric GTA 15E/776 drive systems were chosen for the tests since this size of truck represented the majority of the population of large size haulage trucks and the greatest technical development problems. Test operations have proven the feasibility of equipment designs in actual operation and preliminary economic data has convinced the operators to proceed with planning to modify their entire mining operation to use trolley assist. The initial capital investment incurred for trolley assist can be recovered in a short period of time. Following this quick capital recovery, mines will continue to realize lower operating costs through increased productivity and lower diesel consumption.

Jan 1, 1980

By James A. Curry

Table I identifies the maximum cost of the individual provisions with spoil disposal in Appalachia leading at $3.98 per ton, This was followed by deep mine subsidence control and monitoring at $1.66 per ton. At the request of the U.S. Department of Energy, the Bowser-Morner Testing Laboratories of Dayton, Ohio, evaluated Consol's cost estimates for 14 of the 21 regulatory provisions the company studied. It is interesting to note that Bowser-Morner concluded that Consol's estimates of costs were very conservative and that the actual costs will be substantially higher than what the company reported. In 1978 a joint committee of the National Coal Association and the American Mining Congress made estimates of cost impacts under 11 OSM permanent rules (see Table II). Six rules applied to mid-western strip mining were projected to cost $6.52 to $17.17 per ton. Five rules applied to mid-western strip mines showed costs ranging from $.91 to $6.11 per ton. Three rules applied to deep mines (regardless of region) were seen raising costs from $ .57 to $2.67 per ton. The joint committee reported trouble developing overall figures because member firms used widely different assumptions in calculating their costs. That same statement could no doubt be made when comparing most cost data available today.

Jan 1, 1980

Lead Tariff.--The full House Ways and Means Committee approved H.R. 6089 which will have the effect of reducing the tariff on unwrought lead to 3% ad valorem, with a floor duty of 1.0625 cents per pound, compared with the currently effective rate of 3.5% ad valorem. Consideration is also being given to tariff rates on imports of red lead and litharge from Mexico. A consortium of domestic producers has appealed to the Office of the Special Trade Representative (STR) requesting a return to tariff schedules which were in effect prior to the concessions made effective on January 1. Mexican producers have filed a proposal in favor of lower duties, and the matter now awaits a ruling by the STR. Ferrous Scrap Exports.--After holding public hearings and receiving public comments in May, the Department of Commerce announced that it would not institute formal monitoring of ferrous scrap exports, as requested by the Ferrous Scrap Consumers Coalition. The Department said, however, that it would follow the trend of scrap exports and prices. Ferrous scrap prices are currently low and supplies are reported to be adequate.

Jan 1, 1980

By S. S. Hsieh

The important carboxylic acid components of tall oils were tested individually as phosphate flotation reagents. These included C18 unsaturated fatty acids and C10 to C18 saturated fatty acids and resin acids. These experiments were conducted to evaluate such factors as the degree of unsaturation, hydrocarbon chain length, isomeric form, side-group modification, and cyclic structure. The effects of mineralogical characteristics on flotation response also were considered. The results of this systematic evaluation provide guidelines for selecting efficient substitute reagents and also provide fundamental data for further research on improved flotation technology.

Jan 1, 1980

By R. D. Lopez

The concept of "heat recuperation" for the grate-kiln pelletizing system was first implemented at the Sydvaranger plant in Norway in 1974. Essentially, heat recuperation involves bringing hot air from the second stage of the pellet cooler to the drying zone to increase drying-air temperature to the maximum limit. 'Burner-fuel savings result from a lower kiln secondary-air mass flow at a higher temperature. Because of the fuel benefits achieved at Sydvaranger, heat recuperation has been included innumerous new grate-kiln plants built since then, and some older plants have been retrofitted for heat recuperation. In recent years there has been much confusion about the fuel benefits of heat recuperation. To answer some of the questions, a mathematical model was developed and plant tests were conducted at Minntac Phase 111. Minntac is a magnetite taconite concentrating and pelletizing plant, and Phase III has two indurating lines. This paper presents the results of the studies and plant tests.

Jan 1, 1980

The Porgera gold deposit is an epithermal gold base-metal deposit located in the Enga Province of Papua New Guinea. Gold-silver-sphalerite-galena-pyrite mineralisation is related to stocks and dykes of dioritic composition which have intruded a series of folded marine sediments, mainly shales and siltstones, often with calcareous and carbonaceous horizons, of middle Jurassic to middle Eocene age. The most intensely mineralised zone is at Waruwari Hill, where the mineralisation occurs predominantly as massive mixed sulphide veins, and less frequently as quartz-chlorite veins and as disseminations. Mineralisation occurs in all rock types and several phases of mineralisation have been recognised.

Jan 1, 1980

By Thomas F. Evans

Niagara Mohawk, like other northern coal users, has long experienced increased costs during winter months as a consequence of handling frozen coal. These costs include operating labor, maintenance labor and materials, equipment rental, fuel for thawing, demurrage, carrying costs for excess coal inventory and substitution of higher cost electrical generation for lost production capacity. In the winter of 1978-79, limited trials of several coal freeze conditioning agents were made to determine whether these would provide a cost-effective means of reducing the problems of handling frozen coal. Since these trials were generally effective, the Coal Purchasing Department arranged that all rail coal received during the 1979-80 winter from early December to mid March would be treated at the mines during loading. Inasmuch as the treatment costs are themselves appreciable and our various coal suppliers made a variety of choices of chemical supplier and equipment for application, an attempt was made to evaluate the unloading performance of each train received at the two generating stations which use coal as an aid in the future optimization of the use of freeze conditioning agents. These stations also receive coal by truck but this coal is not treated because of the short hauling time. The C.R. Huntley Station in Tonawanda, NY has a capacity of 800MW and burns about 5000 tons of coal per day during the winter months. The coal is primarily from central and western Pennsylvania but one source in southern Kentucky is also used regularly. Most of the Pennsylvania coal is washed and the fines are thermally dried. The coal is delivered in unit trains made up of mixed cars of 60, 75, and 90 ton capacity. Time between loading and arrival at the station averaged five days and ranged from three to eleven during the 1979-80 winter season.

Jan 1, 1980

By Soma T

Pyrite and Cu-concentrate were roasted in vertically suspended state in an externally heated tube. Tubes of three different lengths of reaction zone were used for three different reaction times. Roasted ores were submitted to chemical analysis and the extent of roasting reactions was determined. In case of pyrite, extent of roasting reactions was not affected much by reactor length and heating temperature (above 500¦C), but was considerably by ore/air ratio. Micro- scopic and XMA examinations led to the conclus- ion that pyrite particles decomposed to pyrrho- tite and then pyrrhotite was oxidized to give Fe-S-0 melt, magnetite and hematite. The extent of reaction was not uniform in all particles but had a wide distribution from unreacted pyrite to completely oxidized particles. Combustion of Cu-concentrate from Kuroko complex sulfide ore ) was unstable under a uniform wall temperature of 450¦C, but proceed- ed rapidly at temperatures above 500¦C. Sticking of roasted ores to the wall of the reaction tube induced choking of the tube, caused by melting of roasted ores, at tempera- tures above 950¦C. Enrichment of oxygen exterted less influence on reaction rate than heating temperature of the tube. Particle size of ore had a big effect on reaction rate.

Jan 1, 1980

By Segnit ER, Jensen G

The decoppering of soft and hard leads was investigated by stirring in an open pot, using sulfur or sulfur plus pyrites, or sulfur plus pyrrhotite, as reagents. Lead samples taken during the process were analysed for copper. Dross samples were examined by optical micro- scope, SEM and XRD. Soft lead containing silver can be decoppered satisfactorily by stirring with 0.1% S at low temperatures - close to 330¦C. Soft lead, whether containing silver or not, can be decoppered satisfactorily at higher temperatures by stirring with 0.1% S plus 0.4% pyrites. Then CuFeS2, Cu5FeS4 and PbS are formed, instead of Cu2S, CuS and PbS when using S alone. Hard lead containing tin can be decoppered satisfactorily by stirring with 0.1% S at temperatures from 320-400¦C. When stirring with 0.1% S plus 0.4% pyrites, reversion of copper from dross to lead on prolonged stirring does not occur. Hard lead without tin can be decoppered with S plus pyrites better than with S alone, but the presence of antimony hinders the decoppering, which is less effective on lead with 5.5% Sb than with 2.3% Sb.

Jan 1, 1980

By Gerhard Mücke

Geothermal and operational reasons in the German coal mining industry make it necessary to an increasing extent to climatize coal faces and headings by means of refrigeration plants. Air coolers installed on coal faces as well as in gateroads play an important part in such climatization. They must transfer, under difficult conditions, the refrigerating capacity supplied by central or de-central refrigeration plants from the chilled water to the air in the workings. The performance data of two new types of coalface coolers and of two different types of gateroad coolers were measured in two testing stations under different thermo- dynamic conditions with dust-free fresh air. As air coolers must be installed particularly at working points with a high .dust load the heat exchanging surfaces are fouled for the most part causing an essential reduction of the refrigerating capacity. The investigations therefore were extended to measurements with a certain dust load in the intake air of the coolers.

Jan 1, 1980

By L. A. Roe

The flotation of fine particles less than five microns in diameter and the flotation of liquids from liquids generally requires bubble generation methods different than methods used in dispersed air type machines used in mineral flotation. Conditions in the separatory zone in mineral cells are generally more dynamic as compared to the quiescent conditions often absolutely necessary for the flotation of fine particles and liquids. An example of quiescent flotation with very fine bubbles is the lithium flotation plant which operated at Trona, California for 34 years, until it ceased operations in 1978. A review of the process development and the commercial flotation operations at Trona is given in this paper. The clarification of oil field brines by flotation of the oil from the brine has been used for over twenty-five years. Recent installations related to the Prudhoe Bay oil field and the Alaska pipeline are described.

Jan 1, 1980

By D. K. Grubbs

Anorthosite is an abundant, domestic source of alumina with reserves in individual deposits ranging from a few billion to hundreds of billions of tons. While anorthosite contains less alumina than does kaolinite, its CaO and Na20 contents are significantly higher (Figure 1). Alumina can be produced from anorthosite by alkaline, soda-lime sinter or acid processes. CaO and Na20 are advantageous because they are reactants consumed in alkaline processes. Acid processes require high calcium plagioclase feldspars (bytownite-anorthite) to obtain high alumina extraction because the lower calcium plagioclase feldspars (andesine-labradorite) are not as readily dissolved during digestion. The layered Raggedy Mountain Gabbro group in the Wichita complex in southwest Oklahoma is a high calcium anorthosite that could be processed by acid, sinter, or alkaline methods. Chemical grade limestone in the Arbuckle Group is located within 45 km of the anorthosite (Figure 2).

Jan 1, 1980

By J. B. Stott

The performance of an adiabatic calorimeter for measuring heats of oxidation of coal is assessed and suggestions made for its improvement and calibration. The use of magnetic analysers for measuring small oxygen deficiencies in air is described and three different methods of measuring the output for such a meter are characterised. The occurrence of spontaneous heating in an 800 tonne heap of Wyoming coal is briefly described. The major part of the report deals with the oxidation of Pittsburgh seam and Wyoming subbituminous coal and describes an experiment in which 1 tonne of Wyoming coal is stored in a 5 metre long insulated container whilst air was passed through. Temperature rises, rates of oxygen absorption and gas compositions of the air stream were measured. The report relates the results of these-experiments to a theory of spontaneous heating developed by Stott and Quan which stresses the importance of the moisture content of the coal and the relationship between the heat necessary to evaporate this water to the heat available from coal oxidation. The work was carried out over a five month period and the emphasis is on demonstrating the effects of moisture transfer and confirming the theory of Stott and Quan.

Jan 1, 1980

By H. Colin

The basic industry, such as mining, ferrous and non-ferrous, cement and aggregates, stores and handles millions of tons of raw materials, re- quiring often different types of storage, blending and reclaiming systems.

Jan 1, 1980

By P. E. Weidmark

"PART I - Published PapersBallivy, G., and Dupuis, M., ""Laboratory testing for the design of grouted rock anchors""; Proc 6th Pan Am Conf Soil Mech Found Eng; Lima; 1:277-291; 1979.Ballivy, G., Ladanyi, B., and Gill, D., ""The effects of moisture content on the strength of fissured rocks""; Proc 1// 1ntnl Congr 1.A.E.G.; Madrid; //:2:7-16; 1978.Baumgartner, P., and Stimpson, B., ""Development of a tiltable base friction frame for kinematic studies of caving at various depths""; Int J Rock Mech Min Sci Geomech Abstr; 16:4:265-267; 1979.Bawden, W.F., and Roegiers, J.-c., ""Discussion and interpretation of the mathematics governing radial flow in a single horizontal rock fracture""; ISBN 07727-7002-6; Dept Civil Engng publication 79-11; Univ Toronto: 134p;1979.Chatterji, P.K., Smith, L.B., and Insley, A.E., ""Construction of Saline Creek Tunnel in Athabasca oil sand""; Can Geotech J; 16:1:90-107: 1979.Coates, D.F., and Gyenge, M., ""A case history of pit slope design""; Proc 4th ISRM Congr; Montreux, Switzerland; Sept 1979; 1:Theme IV:591-596; 1979.Crawford, A.M., and Curran, J.H., ""A dynamic direct shear machine for determining the time-dependent behaviour of rock joints"": Dept Civil Engng publication 79-08; Univ Toronto; 1979.Crawford, A.M., and Curran, J.H., ""A displacement discontinuity approach to modelling the creep behavior of rock and its discontinuities""; Dept Civil Engng publication 79-09; Univ Toronto; 1979.Crawford, A.M., and Curran, J.H., ""A higher-order displacement discontinuity element""; Dept Civil Engng publication 79-10; Univ Toronto; 1979.Cruden, D.M., ""A computer-based system for rock mass description""; Proc 1// Intnl Congr I.A.E.G.; Madrid; //:2:155-159; 1978.Cruikshank, D.J., and Curran, J.H., ""A.B.LE. approach to modelling of fluid flow in fractured rock masses""; Proc 7th Cdn Congr Appl Mech; May 1979; Sherbrooke, Que; 887-888; 1979."

Jan 1, 1980

By F E. Grader

A linear motor properly wound can serve as a mechanism for separating paramagnetic sulphide minerals, like pyrrhotite, from other sulphides and associated gangue minerals. The effectiveness of separation depends on the energising current of the separator, the frequency of the ac cycle, and the particle size of the minerals. The speed of travel of the minerals over the surface of the separator is also a function of particle size, and appears to be constant. The movement of pyrrhotite, magnetite and iron filings of comparable size fraction (150 ¦m +74 ¦m) on the linear motor surface has been observed using a cine camera. An attempt, has been made to give a theoretical basis for the movement of the particles by calculating the minimum electrical energy required to move them. Further, the rate of decay of magnetic moment of the particles has been estimated for magnetite and it has been found that sufficient residual magnetism existed in the particles after they had been exposed to the first half of an ac cycle for them to have like polarity with the second half of the cycle. The particles are therefore repelled from the motor surface every second half of the cycle. This repulsion due to remanent magnetism is the probable cause of particle movement over the linear motor surface.

Jan 1, 1980

By B A. Tapp

The minerals industry in Australia is currently regarded as the country's economic saviour; the bastion of economic security. As Fitzgerald (1974) stated, 'Australia's natural endowments in minerals are the envy of most countries of the world'. As a result the proposed new mineral developments are on a scale that hitherto in the sixties would have been completely un-envisaged. It is reported that Australia is poised on the verge of a 16 billion dollar mining-based investment boom: a boom that will see Australia dominate the energy export field, the mineral processing field, and create the 'coal dollar'. This growth scenario has many inherent dangers, and it is the authors' contention that these should be carefully considered before further development proceeds. Two of the major problems related to the mineral industry growth scenario are the predictability of the future metal market, and the energy cost of mining. The latter problem is the one discussed here. The mining-mineral processing industries in Australia currently use about 36 per cent of Australia's primary energy budget. This large energy input is dominated by two major industries, iron and steel and the rapidly developing a1uminium industry. These two combined use over 20 per cent of the total Australian energy budget. In an industry which is export oriented about 96 per cent as expressed in ex-mine value terms û much of the energy input is exported along with the product. The authors therefore urge that serious consideration by the mineral industry be given to the relatively high energy intensiveness of process operations, especially in respect of the aluminium industry.

Jan 1, 1980

By Wayne C. Smith

Both water pollution and proposed solid waste disposal regulations have a definite effect on the copper leaching industry and some of the major factors affecting the industry are discussed in this paper. New developments of the NDPS are discussed with emphasis on the "toxic" or priority pollutants and EPA's philosophy on the control of these pollutants, The protection of groundwater is the prime aim of RCRA through solid/hazardous waste management. Some of the major elements of the RCA regulations that will affect the copper leaching industry are discussed.

Jan 1, 1980

By Robert F. Chaiken

A novel approach to eliminating environmental and public safety hazards that are associated with fires in abandoned coal mines and waste banks involves the use of in situ combustion technology developed by the Federal Bureau of Mines to accelerate the burning of the wasted coals in place. This technology would be used under exhaust ventilation control conditions that would allow for total management of the hot gases produced. Combustion stoichiometries would be optimized to minimize unburnt combustibles and to maximize the heat content of the gas products, which will be exhausted at one or more fan locations. When necessary, scrubber systems would be employed to remove air pollutants, such as sulfur dioxide; heat utilization systems (process heat, steam, and electricity) would also be employed to offset operational costs. Ultimately, complete burnout would solve the fire and acid water formation problems of the abandoned coal mine or waste bank. Pertinent technical data for burnout control are derived and discussed in terms of the important material and operational parameters. In general, it is believed feasible to operate a burnout system in an existing abandoned mine or waste bank fire at thermal power levels in the range of 10 to 100 Mw, and at exhaust gas temperatures of 1,000° C (1,830° F).

Jan 1, 1980

By Wayne A. Sadik

The mine ventilation system of the Henderson Mine provides a case study of designing and maintaining high-quality respirable air in a large underground mine with over 200 units of diesel-powered equipment. This system was designed with concern for minimizing exposure to personnel of siliceous dust, diesel exhaust, smoke, and potential fire hazards while optimizing general environmental air quality throughout the multilevel/multiheading operation. As a relatively new operation, the Henderson Mine incorporates a modern ventilating plant and mine de- sign as well as state-of-the-art technology where appropriate. Two main ventilation shafts approximately 2,300 ft (701 m) in depth (one intake, one exhaust) will handle 1.8 million cfm (850 m3/s) of air circulated throughout 60 miles (97 km) of drifting, providing the ventilation requirements for more than 25,000 diesel horsepower (18,642 kw) underground.

Jan 1, 1980