Search Documents

By D. M. Soboroff

Etchants containing hexavalent chromium and sulfuric acid are used in a variety of surface-finishing operations. When the resultant spent solutions are discarded, substantial quantities of chromium are lost and pollution prob¬lems are created. To minimize the undesirable environmental effects while improving metal and minerals recycling technology, the Bureau of Mines is conducting research on a method for the economic inplant recycling of these waste etchants. Trivalent chromium, produced when the etchant reacts with a sub¬strate, is oxidized in the anode chamber of a diaphragm cell; other metals, dissolved during the etching operation, are transferred to the catholyte. When waste brass etchants are treated in this manner, all of the trivalent chromium is oxidized and more than 40 percent of the copper and zinc is removed. Similar copper removal and chromium oxidation are achieved with waste printed circuit board etchants and rinse waters from plastic etching operations. The electrical energy needed to regenerate 1 kg sodium dichromate is less than 9 kwhr. Regenerated brass etchants evaluated by two companies equaled or exceeded the performance of fresh etchants.

Jan 1, 1979

By E. M. Frizzell

It is unlikely that improvement in truck efficiency and capacity can fully offset the effects of inflation, fuel cost/shortages, and increasing haul distances as in the past. Therefore, investigations of haulage systems less sensitive to these problems are warranted. Thus, this Bureau of Mines contract research study on alternative continuous haulage systems was prepared. This study identifies the physical, economic, and technological parameters in the application of continuous haulage systems with special attention to under pit slope conveyors and skip hoisting systems. The evaluation data were gathered from extensive literature searches, European/North American mine visits, and industry comments. The study concludes that continuous underground haulage is a viable method within the proper geometric configurations.

Jan 1, 1979

By H. C. Ko

As part of the Federal Bureau of Mines effort to provide thermodynamic data for the advancement of minerals technology, energy conservation, and environmental preservation, the standard enthalpies of formation of a-magnesium sulfate, a-magnesium sulfate, and magnesium sulfate monohydrate were determined by hydrochloric acid solution calorimetry. The values of the standard enthalpies of formation in kcal per mole at 298.15 K are -307.95 ± 0.13 for a-MgS04, -307.03 ± 0.13 for ß-MgS04, and -384.72 ± 0.13 for MgS04 .H2O.

Jan 1, 1979

By J. H. Dalton

The paper reviews the effects of fast-neutron irradiation on the tensile properties of austenitic stainless steels at irradiation temperatures of less than 400°C, using, as an example, work carried out at Pelindaba on an AISI 316 type steel produced in South Africa. Damage produced in these steels at higher irradiation temperatures and fluences is also briefly discussed. The paper concludes with a discussion of some methods of overcoming or decreasing the effects of irradiation damage.

Jan 1, 1979

By Robert C. Gabler

Evaluation of incinerated sewage sludge as a secondary resource for aluminum, phosphorus, and minor constituents such as copper and zinc was initiated as part of the Bureau of Mines secondary resource program. The elemental composition of sludge ash for 14 plants in 11 U.S. cities was determined. Comparing industrialized cities with cities where most of the sewage is domestic, significant differences in heavy metal content were noted. Various parameters were investigated affecting the extraction of metals and phosphorus from a typical industrial city sludge ash and from a Palo Alto, Calif., sludge ash with a high precious metal content. Three extraction-recovery procedures for metals and phosphorus using sulfuric acid leaching, ion exchange, and various precipitation techniques were investigated. The last procedure developed was a combination approach using a three-stage countercurrent sulfuric acid leach that recovered most of the economic values from the sludge ash and also removed the leachable fraction of elements of environmental concern.

Jan 1, 1979

By George J. Conroy, Angel G. Jordan, Eugene W. Bartel

Time-domain reflectometry has long been an accepted and used method for locating electrical faults in electrical cables. The process has, however, required the use of equipment that is somewhat complex and difficult to use. The skill level needed to operate such equipment is high. Therefore, the use of the time-domain reflectometry process has been limited to selected locations and controlled environments. The process, however, has great potential for mine system applications. The ability to locate and repair trailing power cable without removing it from the mine would result in great savings in cost and employee-hours. Therefore, an automatic microprocessor-controlled time- domain reflectometry system was developed to reduce process complexity and skill level needed to operate the unit. The theory of operations is discussed along with the computer analogies used in the unit. The present unit capabilities are presented and future areas of application and research are discussed.

Jan 1, 1979

By J. R. Beeder

Minerals Engineering Company (MECO) is a relatively small, promotionally oriented mineral exploration company founded in Colorado in 1948 during the height of the uranium boom. The company has been: 1. in uranium exploration and production 2. a drilling company 3. a manufacturer of Geiger counters 4. a major tungsten producer 5. then dormat for several years and 6. now we are back into exploration on a broad scale. We have been in underground lead and zinc production in the 1970's but we are now involved primarily in "wheeling and dealing" in mineral exploration. The company has had diverse interests in the past and we are presently diversifying to some extent into oil and gas ventures.

Jan 1, 1979

By James K. Hallenburg

INTRODUCTION The delayed fission neutron, or DFN technique for uranium ore body analysis uses the first down-hole method for detecting uranium in place quantitatively. This technique detects the presence of and measures the amount of uranium in the formation. DFN TECHNIQUE DESCRIPTION The DFN technique depends upon inducing a fission reaction in the formation uranium with neutrons, resulting in an anomalous and quantitative return of neutrons from the uranium. Since there are no free, natural neutrons in formation, a good, low noise assessment may be made. There are several methods available for determining uranium quantity in situ. The method used by Century uses an electrical source of neutrons. This is a linear accelerator which bombards a tritium target with high velocity deuterium ions. The resulting reaction emits high energy neutrons which diffuse into the surrounding formation. They lose most of their energy until they come to thermal equilibrium with the formation. Upon encountering a fissile material, such as uranium, these thermal neutrons will react with the material. These reactions produce additional neutrons, the number of which is a function of the number of original neutrons and the amount of fissile material exposed. The particular source used, the linear accelerator, has several distinct advantages over other types of sources: 1. It can be turned off. Thus, it does not constitute a radioactive hazard when it is not in use. 2. It can be gated on in short bursts (6 to 8 microseconds). This results in measurements free of a high background of primary neutrons. 3. The output can be controlled. Thus, the neutron output can be made the same in a number of tools, easily and automatically. There are several interesting reactions which take place during the lifetime of the neutrons around the source. During the slowing down or moderating process the neutron can react with several elements. One of these is oxygen 17. This results in a background level of neutrons in any of the measurements which must be accounted for in any interpretation technique. These elements are usually uninteresting economically. The high energy neutrons will also react with uranium 238. However, the proportions of uranium 235 and 238 are nearly constant. Therefore, this reaction aids detection of uranium mineral and need not be seperated out. Upon reaching thermal energy the neutrons will react with any fissile material, uranium 235, uranium 234, and thorium 232. At present, we do not have good techniques for seperating out the reaction products of uranium 234 and thorium 232. However, uranium 234 is a small (.0055%) percentage of the uranium mineral and thorium 232 is usually not present in sedimentary deposits. When the uranium 235 reacts with thermal neutrons it breaks into two or more fragments and some neutrons. This occurs within a few microseconds after the primary neutrons have moderated and is the prompt reaction. One system uses this; the PFN or prompt fission neutron technique. We don't use this method because the neutron population is low and, therefore, the signal is small and difficult to work with, accurately. Within a few microseconds to several seconds the fission fragments also decay with the emmission of additional neutrons. Now, with a long time period available and a large neutron population we gate off the generator and measure the delayed fission neutrons after a waiting period. These neutrons can be a measure of the amount of uranium present around the probe. Thermal neutrons are detected with the DFN technique instead of capture gamma rays to avoid some of the returns from other elements than uranium. LOGGING TECHNIQUE The exact logging technique will depend, to some extent, upon the purpose of the measurement. However, the general technique is to first run the standard logs. These will include: 1. The gamma ray log for initial evaluation of the mineral body and for determining the position of the borehole within the mineral body, 2. The resistance or resistivity log for determining the formation quality, lithology, and porosity. 3. The S. P. curve for estimating the redox state and shale content, and measuring formation water salinity, 4. The hole deviation for locating the position, depth, and thickness of the mineral (and other formations), and 5. The neutron porosity curve. The neutron porosity curve is most important to the interpretation of the DFN readings. The neutrons from this tool are affected in the same way by bore hole and formation fluids as the DFN neutrons are. Therefore, we can use this curve to determine effect of the oxygen 17 in the water. Of course, this curve can be used to determine formation porosity. It can also be used to calculate formation density.

Jan 1, 1979

By R. L. Thoms

Compressed air energy storage (CAES) has been initiated recently in West Germany with a 290 MW peaking-power facility utilizing twin cavities with volumes of 150,000 m3 each in the Huntorf salt dome (1). The implementation of CAES in several geologic media is being studied carefully in the United States (2); however, the use of cavities for CAES in salt domes or salt anticlines and the associated long-term stability of these cavities is the specific topic of this paper (3). The cavities represent an essential element in a CAES plant, and thus should be designed and operated to perform with "stability" over the planned life of the overall facility. As employed herein, cavity stability implies the extent to which an acceptable amount of cavity storage volume can be utilized with economic maintenance over the planned life of the overall facility. In this sense stability is relative to the planned use of a storage cavity. Figure 1. depicts the salt deposits of the United States (U.S.) (4). The Gulf Coast region includes the only confirmed salt dome basin in the U.S., although salt structures also exist as anticlines in the Paradox Basin of Utah and Colorado. Because of the relatively small amount of elevation change within the Gulf Coast, CAES in salt dome cavities appears to hold considerably more potential for energy storage in this region than more traditional "pumped hydro" systems.

Jan 1, 1979

By Edward O. Reinbold

The paper presents the results of a study which involved collection and analysis of airborne pollutant concentration data in two producing underground room and pillar metal mines which use diesel powered equipment in the area near the face. The results include the concentrations of CO2, CO, NO, NO2 and respirable particulate matter measured with the latest portable instruments, and the carbon and hydrogen contents of the particulate matter samples determined by combusting them in a Elemental Analyzer. The carbon and hydrogen contents are used to estimate the amount of diesel particulate matter in the mine ambient air. The short term grab sample concentration data, although not suitable for determining compliance with ACGIH Threshold Limit Values (TLVs), are related to the TLVs so that they may be compared conveniently. Lognormal frequency distributions and the arithmetic mean of the concentration measurement data are used to compare different mine situations. Conclusions are drawn as to which pollutants are most important to control under actual mine production conditions.

Jan 1, 1979

By E. D. Palmes

A new type of personal sampler for quantitative estimation of atmospheric concentrations of contaminant gases was first reported from this laboratory in 1972. The sampler requires no pumps or flow regulators and employs instead the motion of the gas molecules them-selves to furnish the power for sampling. Under this grant, work was completed on development of a kit for the field determination of both NO2 and NO. Detailed instructions for the preparation of the samplers and the use of the kit was supplied to the Technical Project Officer. Attempts were made to adapt the same type of sampler to the measurement of SO2 and CO. Both gas chromatographic and turbidimetric procedures for the final estimation of the S02 proved to be unsatisfactory. For CO no reagent was found which would react sufficiently rapidly with this gas to utilize the essential feature of the diffusion sampler, the maintenance of a diffusion gradient which is at least approximately numerically equal to the ambient concentration. A number of publications on use of the NO2 sampler, both at occupational and community air pollution levels, have resulted from this work.

Jan 1, 1979

By Edward D. Thimons

Because of the high number of accidental methane gas ignitions in metal and nonmetal mines, the Bureau of Mines searched for a simple guideline that would allow mine personnel to evaluate the methane hazard in a given mine. Air samples were collected by the Bureau in 53 metal and nonmetal mines and analyzed for trace evidence of methane gas. Samples were collected in the returns and at the working faces. Those mines classified as gassy by the Mine Safety and Health Administration had a significantly higher average methane concentration than those classified as nongassy. Of the 9 gassy mines sampled, 7 had methane concentrations above 100 ppm, whereas only 1 of the 44 nongassy mines had a concentration above 100 ppm. The 100-ppm concentration may be used as a simple and convenient guideline for forecasting the methane hazard in a mine, whether or not the mine is classified as gassy. There was no consistent correlation between commodity mined and methane concentration, nor was there a correlation between mine depth and methane concentration. Neither of these factors can be considered a guideline for predicting methane hazards.

Jan 1, 1979

By David S. Smith

Almost nine years after the assertion of enormous and pervasive federal control over coal mines by means of the Federal Coal Mine Safety and Health Act of 1969, 30 USC Section 801 et seq, as amended by the Federal Mine Safety and Health Act of 1977 (which basically increases the punitive powers of government) a brief assessment of some of the underlying causes, present status, and possible alternatives to governmental control is appropriate. In a governmental system based upon the principles of democracy and the protection of individual freedoms and constitutional rights the ultimate mechanism for abrogation of these rights is the creation and exploitation of fear. Machiavelli in rendering advice concerning the power over men provided by fear stated, "... it is much safer to be feared than loved .. fear preserves (the government) by a dread of punishment which never fails." The Prince. Within the context of the assumption of control by the government over industries or segments of our population - popular fear provides a convenient and almost necessary mechanism for the avoidance by law or regulation of democratic principles. The popular fear of coal mines has been successfully exploited by various goal oriented groups in the past and most recently by a Congressional constituency with a vested interest in controlling the mines through regulation.

Jan 1, 1979

By John A. DesLauriers, Hans J. Broennimann

INTRODUCTION The early record of tunnel excavating machines in hard rock tunneling has not been one to particularly brag about. We have all heard the stories of major difficulties when trying to break hard rock with machines at promised advance rates of several times that of conventional drill and blast. Unfortunately, sometimes this has not happened. It has been through this trial of the past generations disappointments that today's TBM's have evolved to their present high level of performance in a wide range of ground conditions. Today's machines offer much increased reliability and durability. This translates into high availability to the tunnel contractor. Although there still are occasional disappointments being reported, the state of the art is that reliable and predictable machine excavation of rock now is both a reality and well founded expectation. The most recent editions of Atlas Copco's MINI/MIDI Fullfacer, we feel, make a strong contribution to the reliable performance of todays TBM's---especially in small-size rock tunnels. This report will, 1.) explain the equipment and effect of rock both on the cutting technique and machine performance; 2.) list advantages of the non-circular shape, during and after construction; 3.) list applications in civil and mining industries; 4.) discuss North American experiences, performance and costs; 5.) list advantages over drill and blast and; 6.) discuss briefly lease arrangements.

Jan 1, 1979

Mining at Waihi on the Martha Hill commenced in 1878 and between 1892 and 1953 produced 35 million ounces of bullion from some 13.5 million short tons of ore from 40 named quartz reefs. The general geology of the ore is recorded in detail with differing interpretations by Bell and Fraser (1912) and Morgan (1924). The reefs and stringers have formed by fissure filling and replacement in mainly quartz andesite dacite flows within the Waihi 'Graben'. The host rocks are extensively propylitised with intense alteration forming zones of kaolin adjacent to the main reefs.

Jan 1, 1979

Computerized financial models can be used in all phases of the mineral industry from setting exploration targets to projecting profit plans for producing mines. In this presentation, I will use the example of an exploration company entering a new district to trace the application of financial models through the following intermediate phases. 1. Hypothetical analysis and strategy 2. First encounter of mineralization 3. Preliminary drill results - decision process 4. Feasibility studies 5. Post-feasibility negotiations 6. Producing mine 7. Acquisition of producing mines or mineral properties. I will conclude with a brief discussion of the mechanics of the financial models that we use at Wright Engineers Limited. As we progress through the seven phases, the availability and accuracy of the data will parallel the complexity and application of the financial models. However, the same basic financial models are utilized throughout the seven phases. I will begin by suggesting that the exploration group is somewhat autonomous and has the mandate to explore in Western Canada.

Jan 1, 1979

By Jerry L. Purswell

INTRODUCTION The principal OSHA standards dealing with tunneling activities are found in 29 CFR Part 1926. A reference for the applicable subparts which apply to tunneling is included as Appendix A. In addition, some standards from 29 CFR Part 1910 have been identified as applicable to construction and are included in the recent printing of an interim vertical standard for construction (1910/1926 Project). The remainder of this presentation will be focused on past OSHA activities to revise Subpart S of 1926, the principal subpart dealing with tunnel construction.

Jan 1, 1979

By Andrew W. Berg

The Bureau of Mines Mineral Industry Location System (MILS) is part of the computerized Minerals Availability System (MAS), a comprehensive data base of known mineral deposits. MILS, the location subsystem of MAS, has become widely used by the minerals industry and organizations with land-use planning and land management responsibilities. Information on more than 135,000 mineral locations and processing plants in the United States is contained in the data base. This information includes the name, location, mineral commodity, type of operation, bibliography, and cross-references for each property or prospect. Computer-drawn map overlays at various scales showing clustered MILS locations and computer printouts keyed to those overlays are available for inspection and reproduction at the Bureau's Field Operations Centers at Juneau, Alaska, Denver, Colo., Pittsburgh, Pa., and Spokane, Wash.

Jan 1, 1979

By H. A. Gorrell

Preliminary studies of the potential for the production of warm water (up to perhaps 150°C) have been carried out in the Plains region of Western Canada. Production might be from depths as great as about 5 km . Natural waters in this temperature range are currently being used for space heating in other parts of the world. The geography and stratigraphy of the Prairie Provinces are reviewed in terms of their apparent potential for warm-water production. Temperature, salinity and other data provided by wells drilled by the oil and gas industry are reviewed and problem areas are outlined.

Jan 1, 1979

By Michael Gibbons

A method of monitoring roof stability in underground mines by detecting the changes in resistivity of roof material was tested. The device built by the USBM was tested over a 16 month period at the White Pine Copper Mine in White Pine, Michigan. Three falls of ground were monitored by means of as many as 11 sensors. Data indicate a correlation between changes in resistivity and impending structural failure. Problems were encountered with the high roof electrode impedance in the winter and spring due to the drying out of the roof material. Difficulties also developed in obtaining a permanent bond between the roof rock, the conductive epoxy and the electrode plate. Some data were lost due to timer and fuse problems within the unit. These were eventually rectified.

Jan 1, 1979