Search Documents

By Kwang K. Koh, Nicholas C. Nahas, Richard C. Neavel

Sodium, a relatively abundant element in Illinois coal, is reported to cause fouling of utility boiler heat exchange surfaces. Distilled water extraction of 22 Illinois coal samples resulted in average removal of more than 50% of their included sodium. Chlorine was the dominant anion. Extraction rate conformed to Fick's law of diffusion. Extraction with hot water increased both the rate and maximum amount removed. A commercial-scale countercurrent staged process can be envisioned as technically feasible.

Jan 1, 1978

By M. H. Allan

SASKATCHEWAN POWER CORPORATION is a Provincial Crown Corporation responsible for the production transmission and distribution of electric power and natural gas in the Province of Saskatchewan. Through the electric power responsibility, we became interested in the coal reserves in Saskatchewan, which, although still somewhat of an "orphan fuel" in the early and mid 1950's, gave the promise of providing a low-cost source of energy for electric generation. Coal in Saskatchewan, a lignite with an "as-received" heating value of from 5000 to 6500 Btu's per lb and up to 40% moisture, was first recorded in 1853 . By the end of the 19th century, many small mines were in operation in the Estevan, Coronach and Shaunavon areas supplying local inhabitants with a cheap source of heat. These small mines, some of them prosperous, some of them not, continued operation right up to the late 1940's, when oil replaced coal in the market place. The year 1930, however, saw the introduction of the new technique of strip mining in the Estevan area. This technique revolutionized coal mining. It was now possible to use large machinery to uncover the coal and cast the overburden to one side instead of burrowing through thin seams of coal varying from 2 to 10 feet thick. The overburden cast aside by these large mechanical shovels, or later draglines, created heaps of spoil which at that time, during the depression, were a sure sign of prosperity and the welcome news that people had jobs. By the late 1940's, coal production had dropped off, but the spoil piles remained and were now labelled by some as "scars on the landscape", even though there had been some natural succession of grasses. In addition, some people had planted trees in experimental plots and even some aerial seeding had been done.

Jan 1, 1978

By Guy D. Bruno

Through the remainder of this century, world consumption of fluorine per ton of primary aluminum produced will continue to be substantially reduced. Growth of the primary industry will offset some of the unit consumption, but demand for new fluorine sources will decline sharply. Continued application of dry fume scrubbing systems will be the most significant factor in reducing demand.

Jan 1, 1978

By Joseph L. Buckley

A total of 55 conveyor belt fire tests were conducted in the Bureau of Mines Fire Test Gallery, located at the Factory Mutual (FM) Fire Test Center West Glocester, R.I. The objectives of these tests were to: 1) determine the fire resistance and burning characteristics of various conveyor belt materials under simulated mine conditions; 2) provide essential data for designing a reliable bench-scale conveyor belt fire resistance test; and, 3) determine fire test conditions that will discriminate between low, moderate and high fire resistant materials. Belts, representative of those which mold he found in underground coal mines were examined under n umber of experimental conditions which included; ignition intensity; air flow rate; ratio of belt bright (h2) to overall gallery height (h1); exposure time; and, belt width. It was found that fire propagation could be achieved for some "fire resistant" belts (complying with the present Schedule 2G standard for approval) when exposed to an Ignition source of =6000 Btu/min for a 15-min period at a belt height ratio of 01.66. There appears to be a dependency of flame propagation on air flow rates and belt width, although the tests performed do not provide a quantitative trend. Recommendations are made for additional work to resolve some anomalous date and to fill voids in the rest program.

Jan 1, 1978

By H. O. Lien

Among the known iron deposits in Canada, many are of low grade and require beneficiation to produce an acceptable blast-furnace feed. Some of the deposits have never been considered for commercial exploitation due to the lack of a suitable concentrating process. A number of deposits of this type are located in Northern Ontario. The problem in upgrading these deposits is three fold. Firstly, the iron occurs as a mixture of magnetite and hematite. Secondly, the grain size of the material can be fine to very fine. Thirdly, the complex mixture of gangue minerals, which consists invariably of silica, flaky silicates and carbonates, slimes excessively on fine grinding. Algoma's efforts to concentrate these iron-bearing materials culminated in the development of a "Selective Flocculation and Desliming Process" employing slimes removal as the sole beneficiation technique. The process was applied successfully in the laboratory using two stages of grinding and a total of seven deslimings. Prior to the removal of slimes, the iron-bearing fines were selectively flocculated from a thoroughly dispersed pulp using a modified starch as flocculant, Sodium silicate was employed as dispersant. An attempt was made to optimize some of the process variables using material from one specific iron formation near the town of Geraldton in Northern Ontario. The preparation of the starch proved most critical. This matter, and the method used to evaluate the degree of breakdown of the starch molecule, are therefore discussed in some detail.

Jan 1, 1978

By Ven Mercade

The flotation of calcite has been studied by many investigators, especially in terms of type of collector; pH; and metal ions that activate and, more importantly, depress the flotation of calcite (1)(2). Research was extended to the investigation of the effect of polyvalent metal salts and sodium silicate using these materials added separately or in mixtures (3)(4)(5)(6). Flotation of calcite was also studied with respect to its function as a carrier in the beneficiation of kaolin clays by Ultraflotation (7) (8) (9). The carrier used in Engelhard Minerals & Chemicals Corporation's industrial Ultraflotation operation is calcite. This fact, coupled with the continuing interest in Ultraflotation phenomena, led to a study to determine the effect of polyvalent metal-silicate hydrosols on the flotation of calcite.

Jan 1, 1978

By Kenneth J. Miller

Laboratory batch flotation tests were conducted to determine the viability of the Bureau of Mines coal-pyrite flotation process in desulfurizing various coals from the midwestern coalfields. Nine coals obtained from western Kentucky and Illinois were used in the study. In addition to the Bureau's coal-pyrite flotation process, some of the coals were subjected to two-stage rougher-cleaner coal flotation for comparison. The results of this work showed that up to a 70-percent pyritic sulfur reduction could be obtained by flotation and that the Bureau's coal-pyrite flotation was superior to rougher-cleaner coal flotation. Because many of the coals retained far too much sulfur even after second-stage flotation treatment, it was concluded that these midwestern coals are more difficult to desulfurize by flotation than are the Appalachian coals tested in earlier Bureau experiments.

Jan 1, 1978

By R. Tipman, T. C. Burnett

"A general computer program has been written to calculate material balances using multiple regression techniques. The program can handle metal assays or size distribution data obtained in multiple surveys of the flotation circuit. The ""best fit"" weight split is calculated between the input and product streams by minimizing the sum of squares of the residual errors using all of the available data. The program includes an assay adjustment feature in which each assay is recalculated to fit the ""best fit"" mass balance. Thus assay or sampling errors can be easily identified. Also the assays can be statistically weighted so the most precise measurements are given the most influence on the material balance. The computer output reports the mass balance, the actual and corrected assays, the percent metal recoveries and the significance and confidence levels for the weight splits.The program enables a rapid and accurate evaluation of mass balances from large masses of data obtained in multiple surveys around a flotation circuit. The effects of changing process variables can be quickly evaluated with statistical confidence."

Jan 1, 1978

By W. R. Cowan

The availability of mineral aggregates for construction purposes is rapidly declining through inadequate resource planning. restrictive zoning and legislation , and competing land uses. The Geological Branch of the Ontario Ministry of Natural Resources has undertaken to provide aggregate inventory reports for all townships designated under The Pits and Quarries Control Act, 1971, and eventually for all towns hips in heavily populated areas. The reports contain maps and recommendations for extractive zoning by municipalities; of necessity only the largest deposits are given priority recommendations. It is intended that these reports should improve the resource planning in areas underlain by large aggregate deposits. The inventory is only possible because a concentrated effort has been made to map the Quaternary geology of populated areas over the last ten years. Future needs require that we develop methods to determine the extent of poorly defined and buried aggregates and that we look for natural alternatives.

Jan 1, 1978

Twelve years ago, Jeffrey Mining Machinery Division of Dresser Industries Inc. developed the 120H HELIMINER. This machine was the world's first fixed-drum continuous miner and soon became the standard among manufacturers of continuous miners throughout the mining machinery industry. This paper will first outline a brief history of continuous miner development, then discuss significant parameters which are essential to a successful continuous miner design, and finally describe a number of specific applications of Jeffrey continuous miners in a variety of materials, such as coal, potash, iron ore, and trona, around the world.

Jan 1, 1978

By M. P. Hardy

Copper-Nickel ores in northeastern Minnesota could establish a new industry in a region where underground mining has not been active. This study reviews geotechnical data relevant to the selection and design of underground mines in this region and by numerical structural analysis evaluates the importance of some geotechnical parameters to mine method selection. Because of the rapid development of computer modeling many new techniques have become available for modeling rock mass behavior in recent years. An overview of these methods is presented and their applicability to mine design reviewed. Methods included in this summary were the differential continuum models, such as finite Pint and finite difference, integral continuum models, such as boundary element, displacement discontinuity and boundary integral equation methods, and discontinuum methods such as the distinct block model. The displacement discontinuity method was used to evaluate the influence of geotechnical parameters on some aspects of mine design. Three problems; room stability, pillar stability on a weak inclined contact and sill pillar thickness influence on sill pillar stability, were analyzed to evaluate the relative importance of insitu stress field and joint properties on design. It was concluded that for stability analysis the initial horizontal stress is of most importance in all aspects of design. The position, orientation, persistence and strength of joints is also of primary concern. In a more general sense, however, it was concluded that detailed geotechnical parameters have much less influence on mine method selection than more general factors such as rock quality, initial stress state, orebody shape and economics.

Jan 1, 1978

By Charles B. Manula

This paper describes the development of a mathematical model for simulating the behavior of a longwall coal production system. The longwall simulator is a design simulator incorporating both deterministic and stochastic methods to calculate: (a) the size and density of support; (b) the cutting force, power requirements and haulage speed for the loader-shearer; (c) the conveyor size, speed and power requirements; and (d) delay generation at head and tail-gates and the longwall face.

Jan 1, 1978

By Jr. Garnar

Heavy mineral mining has been a relatively small but important Florida industry for over sixty years. Geology of the Florida heavy mineral deposits is similar. Each formed along active coastlines after which the titanium minerals were upgraded in TiO2 by post depositional oxidation and leaching of the iron. There are four heavy mineral plants currently Operating in Florida. Ore is mined by dredges and the heavy minerals concentrated by gravity separation. The heavy mineral concentrates are further processed with high tension and electromagnetic separators to Produce titanium mineral concentrates for TiO2 pigment manufacturing plants. Zircon sand is produced as a co-product at all of the Florida plants. Staurolite is produced by Du Pont and Titanium Enterprises. Du Pont also markets a kyanite-sillimanite product. (Monazite is produced by Humphreys and Titanium Enterprises). Reclamation of mined-out land is an important part of heavy mineral mining. At the Du Pont plants soil is removed ahead of the dredge and placed over the quartz sand tailings. Grass is planted after fertilizing. A year later the land is fertilized again and pine trees planted. Most of the heavy mineral deposits now being mined will be nearly exhausted by the end of the century. New deposits to be mined in the 21st century will probably be smaller and lower grade than those now being mined. Advances in mineral processing technology will have to be made to allow these lower grade deposits to be mined economically.

Jan 1, 1978

By A. E. Ketler

A second generation lighting system was installed in the Greenwich Collieries longwall. This report describes the hardware, installation, maintenance, and final results of the program.

Jan 1, 1978

By J. E. Matta

The methane gas emitted from coal samples collected from the conveyor belts dumping into silos was measured by the Bureau of Mines. Approximately 50 pct of the total gas desorbed into a sealed can within 1 week was released during the first 24 hours. No simple correlation between the gassiness of the coal stored and the methane concentration in the silo open space above the coal was found. This was probably because the gassier coals were stored in open-top Silos, which were better ventilated. Although the methane concentration in the open space above the coal pile was less than 1 pct for all 34 silos investigated, a methane measurement in the coal pile showed that high methane concentrations can exist. The methane released in the pile appears to accumulate and not liberate freely into the open space above the coal pile. Probably this gas is released during reclaiming operations, but further research is required to substantiate this claim.

Jan 1, 1978

By James McManus

The original analogue instrumentation at Lornex Mining Corporation to optimize the throughput by controlling the power drawn by the semi-autogenous mills was found to be inadequate because of the frequent changes in ore type. Although the trunnion bearing pressure of the mill was a crucial control criterion, it was not utilized in the original control scheme. After several plant tests of different types of analogue controllers were unsuccessful in finding any control equipment suitable for this application, it was concluded that a digital process control computer was required. Computer control strategy to optimize the grinding rate by controlling the power and the bearing pressure of the semi-autogenous mill was developed and a Fox 2 /30 computer made by Foxboro was selected. After six months of experimentation, it was found that the throughput was increased substantially by computer control.

Jan 1, 1978

By E. Allen Hendt

It is a pleasure to be invited to speak before a gathering of executives representing America's leading mineral companies, I welcome this opportunity, particularly because it comes at an important period in the development of U.S. commodity policy. This morning, I discussed our general commodity policy primarily in the. Context of the north-south dialogue between developed and developing countries. This afternoon, I would like to focus more specifically on potential cartel activity and U.S. mineral import dependence.

Jan 1, 1978

The clay slime generatea in many sand washing operations is usually very difficult to de-water. Treatment of these slimes is often limited by economic considerations and the properties of the solids to a gravity-driven process. The moisture characteristics of kaolinitic slimes from two different sand washing operations were measured.From these curves, equilibrium moisture contents for sedimentation and for drainage were calculated using the methods of soil physics. The validity of these calculations were confirmed by column experiments.The results show that the increased de-watering to be gained by drainage, as compared with sedimentation, is significant. Furthermore, observed rates of outflow indicate that water can be removed considerably morerapidly when drainage is possible.The practical application of these results to the dewatering of clay slimes is discussed.

Jan 1, 1978

By Frank W. Bowdish

During the early 1960's, a method was developed for refining sand from the Arkansas River to produce a feldspathic product that was proposed for use in making colorless glass. Because of the need for chemical uniformity, a cooperating glass manufacturer specified certain ranges of percentages for each chemical constituent of the sand. These specifications were met by fulfilling the single requirement that alumina vary by no more than 20.1 percent from the specified value. This translated to a total variation of only about 1 percent in the feldspar content of the mixed quartz-feldspar products. Because the feldspar was lighter than the quartz, the average density of refined sand varied depending on composition. Densities, determined to five significant figures, of several samples were correlated with their chemical analyses, and the correlation could then be used with density determinations to more reliably indicate compositions than by chemical analyses only. The effects of several variables on the composition of refined sands were studied. There was a regular variation in the proportion of feldspar with screen size. A series of samples with their natural size distributions were more nearly uniform in composition than the same sands after screening and recombination. The screening and recombination process was done so that the sands had identical size distributions. Variations in the refining showed little effect on composition. A pile of flow-back sand from a construction sand washer was found to be severely segregated. However, samples taken from many points in the river near the sand plant and from the flow-back discharge pipe over several weeks very nearly met the uniformity specification. If care was taken to avoid segregation either before or during processing, it should be possible to meet the uniformity specifications for a feldspathic glass sand.

Jan 1, 1978

By H. J. Schroeder

Legislation and Government Programs.-The Occupational Safety and Health Administration (OSHA) accepted written comments until July 23, 1976, and held an informal hearing on August 24, 1976, to receive oral testimony regarding an economic and inflation impact statement prepared by OSHA on the proposed standard for occupational exposure to inorganic arsenic. These written and oral submissions were to be used in conjunction with information supplied at 1975 hearings to promulgate emission standards. An in-depth study for the Environmental Protection Agency (EPA) assembled and interpreted comprehensive information on arsenic and its compounds and the effects of these substances on people, animals, and plants.2 Another study for EPA assessed the role of arsenic and its compounds in the environment and in the economy of the United States and evaluated the need for and the projected effect of controlling its production, use, dissipation, and emission.3

Jan 1, 1978