Search Documents

By A. E. Hall, R. N. Taylor, J. G. Taylor

The introduction of tunnel-boring machines to South African gold mines has created problems and challenges which accompany any new technique. This paper describes the experience gained in this field, especially in the design and erection of a tunnel borer and in boring and environmental conditions.

Jan 1, 1978

By Desmond Y. M. Lee

This paper presents a procedure to prepare input for the computerized pit design system at Iron Ore Company of Canada. The procedure is simple and requires very little training. Also, it is general enough to accept both bench (horizontal cross section) maps and section (vertical cross section) maps. The output of this procedure is data which represent blocks of ore and waste with dollar values based on mineral content. The ultimate pit design is presented in printer-generated graphs, with numbers indicating the depths of pit bottom walls. Roads are added manually by the engineer with the aid of other computer programs. Section maps and bench maps are also printed as part of the output of the ultimate pit design.

Jan 1, 1978

By W. R. McDonald

The Bureau of Mines, U.S. Department of the Interior, conducted small-scale field tests on acidic copper tailings as part of its effort to develop, improve, and demonstrate technology for stabilizing mining and mineral-processing wastes. Two successful demonstration revegetation plots were established on an abandoned copper-tailings pond located on public land adjacent to Holden Village, Wash. The tailings were neutralized with treatments of either dolomitic lime or limerock and fertilized with processed sewage sludge and/or commercial fertilizer. Excellent plant growths covering 70 and 24 percent of the surface were achieved on 1/8-and 1-1/2-acre test plots planted in 1973 and 1974, respectively. Regar brame, Tegmar intermediate wheatgrass, and tall wheatgrass provided the best plant growth and surface coverage. The target pH of tailings neutralization was 6.8; however, good plant growth occurred in areas where the soil pH ranged from 2.9 to 5.8.

Jan 1, 1978

By P. A. Croce

A total of 17 mine gallery fire tests (23 including sub-tests) were completed during this report period (10/1/76 - 11/30/77), directed at identifying a hazardous timber-set fuel-loading in a mine passageway that is otherwise free of combustibles. Results of these initial tests show that the capability of a particular fuel loading for propagating a fire is dependent upon the imposed ventilation air velocity and the ignition intensity, although this dependency needs to be better defined. It is also apparent that care must be taken when relating gallery test fire behavior to actual mine fire behavior, because of the restrictive length of the gallery. Present data indicate that some modification to the instrumentation scheme may be advantageous before proceeding with future tests.

Jan 1, 1978

By J. B. Davis

Isotope analyses distinguish biogenic sulfur ores from non-biogenic ores, but do not distinguish bioepigenetic from biosyngenetic ores. Sulfur deposits of salt dome caprocks and of bedded Permian evaporites of west Texas, however, are clearly bioepigenetic. Anhydrite, introduced by salt diapirs into geologically younger sediments, is converted biogenically to sulfur and calcite in the presence of petroleum; for example, in Challenger Knoll, a salt dome at a water depth of 3600 m in the Gulf of Mexico. Bedded evaporites of west Texas in association with petroleum show an obvious epigenetic replacement of the anhydrite layers by biogenic sulfur and calcite

Jan 1, 1978

By Wayne A. Van Voast

Many coal beds that will be mined in southeastern Montana are aquifers that provide essential local water supplies. Mine cuts along aquifer outcrops create almost imperceptible piezometric changes. Monitoring near such operations at Colstrip has detected almost no water-level declines in observation wells. Mine cuts between outcrops induce rapid storage depletion and associated piezometric depressions. One such cut near Decker induced 1,250 m3/day of flow from storage and created a piezometric depression of 3 meters or more as far as 1,500 meters from the mine. No wells have yet become non-productive but losses of some are inevitable as operations expand. Alternative supplies are available from aquifers stratigraphically below the disturbed materials. Effluents from active mines are chemically similar to other area waters because they are mixtures or ground waters entering the mine cuts. Occasional high concentrations of nitrate do occur, however, as residuals from explosives. Spoils generally consist of confined aquifers of wasted coal and coarse rubble at their bases, overlain by finer-grained sand, silt, and clay. Hydraulic conductivities and storage coefficients are comparable with those of undisturbed confined aquifers. Water quality in mined lands is highly diverse because of diverse spoils lithologies and poorly-established ground-water circulation. Ground water in spoils is more mineralized than in the coal beds and chemically resembles waters from sandstone aquifers. Hydrologic effects of mining will not be catastrophic or widespread but may have local significance. Most notable changes will be in water quality; availability will not be permanently reduced.

Jan 1, 1978

By Rhual L. Guerguerian

MINING has been practised by mankind for over sixty centuries (1). In 1876, the "ball mill" was patented, and during the century that followed rotary grinding developed to the state where individual machines are treating tens of thousands of tons of ore per day. This paper gives a brief description of design practices prior to the availability of advanced facilities, followed by modern analytical design development at Dominion over the past ten years.

Jan 1, 1978

By Peter C. Jones

The paper gives a broad view of the maintenance procedures at the Cassiar Asbestos Corporation property. Comparisons are drawn to indicate the changes in facilities and approach that have evolved over the last 25 years while coping with the northern British Columbia climatic conditions. Special emphasis has been placed on the importance of the support groups providing services for both the mine site and the town.

Jan 1, 1978

By Joseph Kuti

Longwall mining is the term used for the underground extraction of a wide and deep panel of coal. Such a panel may be blocked out by one or more entries on either side ("head" and "tail") of a longwall face. If all the entries are pre-driven, the panel extraction is termed longwall retreat mining. With one exception, all the longwall faces in the United States are of this type. (1) prior to the general decline in the rates of production with Continuous Miners, the development of the multiple entries generally kept ahead of the longwall extraction rate. This is no longer the case: longwall extraction rates far exceed the rate of development. In addition to this problem, in newly established mines, the development of a haulage and bleeder system based on multiple entries results in a lead-time of three years or more before longwall mining can be applied. This is one reason why earlier projections and much of the optimism attached to longwall mining as a principal "savior" in the energy crisis should be viewed with some caution.

Jan 1, 1978

By Victor R. Eyzaguirre

Cerro Verde is one of several large porphyry-type copper deposits in Southern Peru. The copper occurs as primary sulphides, with a significant oxide capping. The exploitation of the deposit has been correspondingly divided into two stages, the first consisting of copper production from oxides, and the second from sulphides. Minero Peru successfully started the Stage I plant in June of 1977 with the first production of electrowon copper cathodes. This paper is essentially devoted to a description of the Stage I process, which can be summarized as follows: Ore is trucked to the primary crusher, where it is crushed to 225 mm and conveyed to a coarse ore stockpile. Ore withdrawn from the stockpile is secondary crushed to 65 mm, conveyed to a truck loadout bin, loaded into trucks and driven to the leaching pads. Ore is placed on the pads in lifts and sprayed with sulphuric acid solution to dissolve the copper. Copper-bearing solution forms a pond behind a dam at the lower end of each pad and is pumped from there to the solvent extraction plant. Copper is extracted from the leach solution into an organic phase and is then stripped from the organic phase to form a purified concentrated copper solution suitable for feed to electrowinning. In electrowinning, the copper is finally recovered as cathodes suitable for sale as refined copper.

Jan 1, 1978

By Clayton J. Bossart

The design and fabrication of an engineering model and three prototypes of a portable gas analyzer and sapling system is herein described. This design effort has provided a battery operated system which will indicate the degree of explosivity of return air and in the air beyond the seal during the course of fighting, sealing and quenching a mine fire. Performance tests, design criticisms and recommendations for designs are also included. The system is based on two analyzers: the MSA Catalytic Combustible Gas Analyzer for indication of total combustible gas concentration and a modified, totally automated version of an Analytical Instrument Development Corporation Model 622 gas chromatograph (CC) for analysis of individual gases. The system provides continuous monitoring of combustible gas level in the range of 0 to 100% LEL. The GC automatic analysis requires a 5 minute cycle time to update the concentration indications for: hydrogen @ 0 to 10% oxygen @ 0 to 25% nitrogen @ 0 to 100%, methane @ 0 to 10 or 0 to 50%, carbon monoxide @ 0 to 5% and carbon dioxide @ 0 to 10%. CC peak heights are translated into concentration units which are memorized and continuously displayed on Integral meter readouts. The underground analyzer system design was reviewed and tested by the MESA Approval and Certification Group and found to meet intrinsic safety requirements. The three underground packages consists of: a gas chromatograph with dimensions of 11" X 12" X 16" and weighing 25 lbs. , an electronics unit 10" X 14" X 19" in size and weighing 30 lbs., and a power pack 6" X 14" X 16" in size and weighing 45 lbs. Two AC/DC power supplies are provided for aboveground battery charging and system operation in the laboratory. The underground system is entirely automatic and self-contained, including sources for electrical and pneumatic power and for CC carrier gas via a rechargeable Gel Call battery and two lecture bottles of gas in the power pack-

Jan 1, 1978

By D. A. Paice

A portable calibrator to check tie trip setting of dc circuit breakers within an accuracy of +5% has been developed for the Bureau of Mines. It operates from a 300 volt dc trolley wire to provide controlled current pulses of 120 milliseconds duration and continuously adjustable from 1400 to 3600 A. These current pulses enable a breaker dc trip current to be determined and subject the contacts to full current rating. The equipment is simple to use and weighs 86 pounds. Connections are made with protected, clamp-on leads which are separately connected and weigh about 22 pounds. An accurate calibration procedure takes less than 5 minutes to complete.

Jan 1, 1978

By D. E. Traut

A fluidized countercurrent ion-exchange system was developed, operated, and evaluated by the U.S. Department of the Interior, Bureau of Mines. The system consisted of integrated multiple-compartment absorption and elution columns in which the solution flows were continuous except for short periods when resin increments were withdrawn. The exchange of uranyl carbonate between a simulated in situ uranium leach liquor and a strong-base ion-exchange resin together with the subsequent elution with an ammonium chloride solution was studied. The effects of the number of sections, section height, amount of resin withdrawal, solution flow rate, and column diameter were investigated. The kinetic and equilibrium relationships for the absorption and elution steps were also examined. The experimental data indicate a strong interdependence between variables. Solution retention time appears to be a major limiting variable in the absorption process, while resin residence time is the determining factor in the elution process. The column was efficient over a range of conditions, but close control was needed for optimum operation.

Jan 1, 1978

By J. J. C. Heynike

The relationship between population growth and steel consumption since the beginning of the twentieth century is indicated, reference being made to the increasing capacity of production units and the resultant increased pollution in the same area. The need for the control of fugitive emissions with its associated high cost is pointed out. There is a direct relationship between energy and pollution, and examples are given of several improvements that have been made to achieve better energy usage and reduced pollution. Several practical examples of air-pollution control systems are described as applicable to the main metallurgical steel processes of today. In conclusion, reference is made to the fact that, with the improvements attained in reducing pollution, the public will not tolerate a decline in the standards already attained. Environmental control and better energy utilization will continue to be important aspects of steel-plant design and operation.

Jan 1, 1978

By Nicol S. K, Firth B. A

Much effort over the years has been put into the task of devising parameters which adequately assess the metallurgical efficiency of mineral processmg operations. One of the most celebrated of these methods is the so-called "release analysis" method of Dell (1953) which tackles the problem in terms of an ideal separation based on sequential retreatment of the products and tails of a given separation process. Other methods have also been proposed by Jowett (1969) and by Holland-Batt (1971 ). While these procedures are appropriate to multi-component mineralogical separations, they perhaps do not lend themselves to the much more simple two-component systems encountered in coal preparation. However Dell (1962) has suggested the use of the term "specific profit" in coal preparation in order to assess the conditions that give maximum economic gain. Specific profit is derived from data relating washability data with equipment performance and operating costs. The procedure for using this criterion for comparative purposes is therefore somewhat cumbersome as is illustrated by its lack of widespread acceptance in the coal preparation literature.In contrast, an efficiency index, E, which is both simple and meaningful from the utilitarian standpoint, has been proposed by Tsiperovich and Evtushenko (1959a). This index is defined by the relation, E = Yield X Tailings ash/Product ash (1) A cursory examination of this parameter shows that it increases when yield and tailings ash increase and also when product ash decreases; all of which are desirable circumstances in coal cleaning operations.Further, it will be shown that slight variations in operation are amplified by this function which makes comparisons simple and direct.While the use of this index is quite extensive in the Soviet coal preparation literature for some reason it has not received wide usag~ elsewhere.

Jan 1, 1978

By Richard L. Sanford

This paper summarizes the results of the development of a Directory of Computer Programs Applicable to U.S. Mining Practices and Problems. The Directory is funded by the U.S. Bureau of Mines and includes a sampling of computer usage in operating and manufacturing companies, consulting firms, computer companies, research organizations, universities, and various U.S. government agencies. General references to computer applications throughout the mining industry are discussed as well as the availability of programs to interested organizations or individuals.

Jan 1, 1978

By H. M. Garrett

Dr. Ft: L. Handy of Iowa State University's Engineering Experiment Station very handily reduced the relatively complex cement making process to ultimate simplicity: "Take two cups of crushed limestone; add one-half cup of clay or pulverized shale (plus perhaps some sandstone or iron ore; depending); mix thoroughly and grind up fine. Bake in white-hot oven at about 2,600 F. Cool. Add a tablespoon of gypsum: and, again, grind very fine. If you can do this for about a penny a pound, you can almost compete.' Before Dr. Handy's time, is the early days of the U. S. Cement Industry, from 1817 when the Erie Canal was started to 1895 when the first rotary kiln was built, this was the recipe, more or less. Dr. Handy's raw materials were deposited in a natural "cement rock" found in the Hudson, New York and Lehigh, Pennsylvania valleys. At first the natural rock was pulverized (not ground fine) and interlayed with wood for "baking" at about 1,800° F in a batch process vertical shaft kiln or beehive oven; then the calcined pozzalonic (lime and silica) product was cooled and ground fine for shipment in wooden barrels. Later, in 1871, true portland cement was made. The same natural rock was ground fine to make briquettes; interlaced with wood or coal in the "Beehives"; and baked at a clinkering temperature of about 2,6000 F to produce clinker (calcium silicates) which was ground fine for sale. In those days, the crude cements dropped in price from over 1 cent to 1/2 cent per pound. In 1895 the rotary kiln introduced-continuous instead of batch processing. The countercurrent process allowed the same raw materials (now finely ground to about 80% minus 200 mesh like face powder) to be fed at one end of the rotary kiln. Heat from a coal burner was introduced with combustion air at the other end to produce the requisite clinkering temperature. The clinker product was discharged for atmospheric cooling, mixed with gypsum, and again ground fine as face powder. The cement was sold primarily in barrels, later in jute or cloth bags, then paper bags, and now primarily in bulk truck and barge carriers. The price dropped to a 1/4 cent per pound by 1910, but with recent inflation it now sells for 2 cents per pound.

Jan 1, 1978

By Kenneth Savidge

With the recent demand for increased coal production there has been a corresponding increase in the horsepower of the shearing machines. The resultant increase in the machine haulage pull has heightened the incident of haulage chain breakage resulting in machine downtime, but more seriously the danger to face personnel. This paper discusses the application of chainless haulage to longwall mining and describes the systems currently available.

Jan 1, 1978

By R. D. Brown

In his April 10, 1978 budget address, Finance Minister Chretien declared that the federal government will restrict the growth of its spending to less than the trend growth of the gross national product; over the past year, both the federal and a number of provincial governments have taken action to cut back on spending policies. This new emphasis in restraint would seem 10 be a response to a mounting public reaction to the rapid growth of government spending - and taxation - over the past 25 years. Although this relatively new government posture on public spending may be admired by many, to others it raises the question: "Can the growth in government spending really be stopped?" This article comments on just how government revenues - and spending - have grown over the past few years in Canada, and mentions some of the issues relating to a slowdown in that growth.

Jan 1, 1978

By Moresby J. F

Segregation roasting was used to recover more than 85 per cent of copper from crushed, minus 14 mesh refractory furnace-lining bricks. A plus 14 mesh fraction: which was high in copper, could be recycled directly to the smelter, giving an overall recovery of approximately 90 per cent. An oxidation roast at about 700°C was necessary, before segregation roasting, to convert copper sulphides and copper metal to sulphates and oxides. Withsegregatron temperatures in the range 600°-650°C the quantities of solid carbon and NaCI required are 2-5 per cent and 1 per cent respectively. P.V.C. coating from scrap copper wire can be used instead of NaCl as asource of hydrogen chloride for the segregation reaction.

Jan 1, 1978