Search Documents

The industrial might of the Bowen Basin is primarily the result of Utah Development Co.'s work- which has opened up the Blackwater, Goonyella, Peak Downs, and Saraji mines; built the Hay Point port; and is now developing the Norwich Park mine.

Jan 1, 1977

By Robert B. Scott

The Dents Run Demonstration Project near Morgantown, West Virginia, was a cooperative venture involving the U.S. Environmental Protection Agency (EPA), the Water Resources Division (WRD)(1) of the West Virginia Department of Natural Resources (DNR), and the Christopher Division of the Consolidation Coal Company (CONSOL). The object of this project was to demonstrate pollution control methods and to clean up a 37.8 sq km (14.6 sq mi) watershed severely polluted by coal mine drainage. A study entitled, "Water Infiltration Control to Achieve Mine Water Pollution Control" (EPA-R-2-73-142),(2) was conducted by the Cyrus Wm. Rico Division of NUS Corporation for the grantee to determine the feasibility of utilizing remedial techniques to improve the Dents Run water¬shed. This study showed that the Dents Run watershed was discharging as much as 6,870 kg/day (15,100 lb/day) of acid; 1620 kg/day (3,560 lb/day) of iron 17,250 kg/day (38,000 lb/day) of sulfates; and 29,500 kg/day (64,900 lb/day) of total dissolved solids into the Monongahela River near Morgantown, West Virginia. This pollution was caused by the combination of borehole pump discharges from active underground mines, runoff from abandoned strip mines, and runoff from refuse dumps.

Jan 1, 1977

By Yu A. Chernegov

Building up the USSR's economic strength was the result of all the achievements and successes of our economy. The Soviet Union was the first to begin planned guidance of the economy. The mining industry of the USSR, which holds the first place in the world output of mining production, has always been considered as the main raw materials basis of the country's economy. High and stable development rates are a feature of planned economic management, based on the social ownership of the means of production. During the past ten years from 1965 to 1875 the national income used for consumption and accumulation increased practically by 1.9 times. There has been no inflation, no unemployment in the Soviet Union for about forty years already. High and stable growth rates of the production of mining industries and that of the branches, which are their direct consumers are characterized by the data in table I. The achievements and successes of the economy's development are to a great extent determined by the three planning components, which are as follows:

Jan 1, 1977

Although Australia is the world's second biggest producer of iron ore, the last few years have not been easy for companies in Western Australia's Pilbara region (see map) where more than 90% of the nation's iron ore is produced. For at least two years, the industry has been plagued by dwindling markets abroad, production-crippling strikes at home, skyrocketing costs (well above the official 13% annual inflation rate), an acute shortage of investment capital, increasingly ferocious competition from foreign iron ore producers-and, as if all this weren't enough, by an over-valued currency that has caused incalculable damage not only to iron ore producers but to the entire mining industry of Australia. (This last problem was mitigated less than two months ago, on November 28, 1976, when the Australian dollar was devalued by a whopping 17 1/2%.)

Jan 1, 1977

It is indeed a privilege and honour to deliver the keynote address at this 15th APCOM symposium. APCOM has played a significant role in my own career and I am sure in the careers of many of the thousands of other participants over the years since its inception as a short course on "Computers and Computer Applications in the Mineral Industry" at the University of Arizona in 1961. The technical papers and addresses presented at the 14 past symposia provide an imposing record of sustained pro- gress and achievement in the field of computer applications. I will not attempt to analyse this technical side of APCOM but rather endeavour to provide you with a broad popular perspective of the road travelled to date and that lying ahead of us. The name of the series of symposia has changed from time to time, with titles such as Mathematical and Statistical Techniques, Mining and Exploration, and Decision Making being used at various times until in 1972 the name APCOM was coined and the present loga designed by the South African organising committee for the 10th symposium. It can conveniently be accepted as standing for:

Jan 1, 1977

The Southern 'B' lode orebody at the New Broken Hill Consolidated Limited (NBHC) mine, Broken Hill, is a continuation of the zinc-rich orebody that was first mined in NBHC in the 1940's. Preliminary diamond drilling in the early 1960's resulted in sufficient information to delineate the southern extension of the presently mined 'B' lode orebody, In 1966 the sinking of a 7.3 metre diameter circular shaft (No. 3 Airway) was commenced to improve the ventilation of the southern extremities of existing workings and to provide a base to further explore and develop the orebody extension. Development on four levels was started in the early 1970'.s to link the existing workings with the new shaft. Three possible mining methods - sublevel open stoping, loader cut and fill with ramp access and sublevel caving - were investigated and the decision was made to mine the orebody by transverse sublevel longhole stopes and pillars with trackless equipment and ramp access between the major working levels.

Jan 1, 1977

By Ralph H. Light

The recent surge in demand for uranium in the United States, accompanied by a significant increase in price, has resulted in exploration, mining, and milling of lower grade ores than have been exploited in the past. To sustain production levels of uranium with lower grades of feed requires larger tonnage mill operations. Also, because of recent environmental regulations, mill operations must be prepared to properly contain large tonnages of tailings, and recycle, treat and discharge, or evaporate mill effluents. Thus, the advent of lower grade ores, larger tonnage mills, and environmental considerations has made the cost of milling a critical factor in today's uranium production economics in the United States. Three basic milling methods are employed for extracting uranium from ores: 1. Acid leach, countercurrent decantation, and solvent extraction. 2. Acid leach, resin-in-pulp, and Eluex. 3. Alkaline leach, solid-liquor separation, and precipitation. Vanadium often occurs as a valuable by-product in ore deposits located in the Uravan mineral belt in Western Colorado. Also, lesser amounts of vanadium may occur in ores from South Dakota, New Mexico, and Utah. Vanadium is usually extracted in the acid leach solution with uranium and recovered by solvent extraction after recovery of the uranium. By-product recovery of uranium from phosphoric acid and porphyry copper dump leach solutions is now receiving considerable attention. Pilot plant studies are under way and construction of commercial plants is in progress.

Jan 1, 1977

By Gregory L. Gullord

In September, 1975, production was begun at the new milling facility of ASARCO Incorporated, the Young Mill. The mill is located adjacent to the Young Mine 35 km (22 miles) east of Knoxville, Tennessee. The Young Mill replaced the obsolete Mascot Mill which had been operating since 1913. The basic flow sheet of Mascot was retained for the construction of the Young Mill, with a 20% increase in capacity included in the design. The Young Mill is capable of processing 7710 - t/d (8500 stpd) of crude ore from three underground mines (Young, Immel and Coy) yielding 300 - t/d (330 stpd) of 63% zinc concentrate. The Young Mill is unique in that 92.5% of the ore milled is recovered as saleable products, including zinc concentrate, construction aggregate, sand and agricultural limestone. Processing at the Young Mill is divided into five basic stages: two-stage crushing, heavy media separation, grinding-flotation, concentrate filtering and drying, and limestone by-products recovery. The ore bodies are located in the Knox formation, which consists of primary dolomite, secondary dolomite and limestone with silicas in the form of chert and jasperoid. The zinc mineralization occurs as an exceptionally pure sphalerite. The ore contains an occasional abundance of pyrite and traces of fluorite and barite. TWO STAGE CRUSHING Ore enters the crushing section from two points. The Young Mine ore is hoisted into a 816 ton (900 st) bin which feeds a 1.52m (60 in) conveyor via a 1.52 m (60 in) vibrating feeder. The Immel ore is trucked 10 km (6 miles) by an independent contractor and weighed on automatic recording truck scales at the entrance to the property.

Jan 1, 1977

By Ray H. Hario

Background of Erie Mining Company Erie Mining Company, managed by Pickands Mather & Co., is one of the largest producers of iron ore pellets in the United States. The plant is located at Hoyt Lakes, Minnesota, sixty-five miles north of Duluth on the eastern end of the Mesabi Range. Taconite Harbor, situated on the north shore of Lake Superior, is the location of its Power Plant and shipping facilities. (Figure 1) Even though the plant commenced operation in September, 1957, its true be-ginning can be traced back to 1931 when Pickands Mather, in conjunction with Bethlehem Steel Corporation and Youngstown Sheet and Tube Company, began investi-gating the possibilities of processing low grade ores. In 1940, Erie Mining , Company was formed. During the early and middle 1940's, laboratory and pilot plant research was proven to a point where a preliminary plant was deemed feasible and built in 1948. This plant had an annual capacity of 203,200 t (200,000 long tons) per year and, until mid-1952, was the only taconite plant in existence using commercial-size equipment. During this period, ownership of Erie Mining Company was expanded to include Interlake, Inc. and The Steel Company of Canada, Limited. In 1953, authorization was obtained from the owners to build a 7.62 M t (7.5 M long tons) per year plant at a cost in excess of $300,000,000.

Jan 1, 1977

By James M. Link

A program was initiated tinder sponsorship of the U. S. Bureau of Mines to investigate pipeline behavior of raw and spent oil shale slurries. Slurries were recirculated in pipeline loops with 150-mm and 200-mm diameter horizontal test sections and a 150 -mm diameter vertical test section. Slurry concentrations from 10 to 60 weight percent were investigated. Critical and deposition velocities were observed. Head losses were measured at various velocities. Rheology measurements were made on representative homogeneous samples from the pipeline. From these data, pipeline energy requirements were predicted by computer and compared to pipeline data. Computer programs were also used to analyze pipeline data for two flow models: 1. Heterogeneous flow regime for coarse, settling slurries 2. Homogeneous flow regime for nonsettling suspensions The economics of slurry transport of raw and spent shale were examined. Cost estimates encompassed a range of pipe diameters to transport a wide range of throughputs of both raw and spent shale. Similar estimates were made for conveyor belt systems to provide a valid cost comparison. Economic comparisons are valid in a general sense, but a specific study must be made to determine the cost advantages of hydraulic transport for a given mine.

Jan 1, 1977

By P. J. G. du Toit

Coal has been mined by hydraulic means in various countries, i.e., the hydraulic excavation as well as the hydraulic transportation of coal has been practiced. The hydraulic breaking (excavating) of the coal dealt with in this report is done with a monitor directing a continuous jet of water against the coal, pressures of the water fed to the monitor range from 1500 to 2500 psi at 1000 to 2100 gallons per minute Transportation of the coal from the face is by fluming if a gradient exists in excess of 2 or, when a favorable gradient does not exist, the coal is pumped from the face by various types of pumps which can also provide a means of hoisting the coal to a higher elevation as required. This report presents: 1.) preliminary design and systems specifications of a demonstration miner (referred to in this report as a hydrominer), 2.) mining configurations showing good promise for typical U.S. thick coal seams in three seam pitch categories, (0° - 7° = Flat, 8° - 250 = Moderately pitching, 26° - 90° = Steeply pitching), along with cost and performance analyses for each system, 3.) a definition of a test program that will provide sufficient engineering data for the design of a water jet cutting head adequate to cut coal in those typical U.S. thick coal seams The cost analysis data showed hydraulic methods to be economically competitive with present thick seam raining methods. It was also obvious from studies of thick seam methods that the hydromonitor coal breaking techniques are more effective in removing most of the coal with its long reach of 60 ft. (or more), is a safer mining system, and produces very low coal-dust content in the air (usually less than 0.25 to 0.5 mg/cubic meter). It is recommended that the USBM sponsor a full fledged continuation of the hydraulic mining program: (a) lab, test, (b) preliminary field test, (c) full scale mine section demonstration.

Jan 1, 1977

By H. M. Coggin

The study summarizes the state of the art in rock mechanics, open pit and underground mining, leaching, geology, metallurgy and financial analysis Conceptual design of pit slope caving technique and analyses explore concepts for the exploitation of ore grade remnants in the walls and bottoms of open pit mines and the potential economics of the adaptations Several coded sites were examined for future studies where the feasibility of the method may be demonstrated. An extensive bibliography has been developed

Jan 1, 1977

By R. E. Gray

[The purpose of the study is to investigate cases of subsidence over abandoned mined-out areas of the Pittsburgh Coal identified from published and unpublished sources and to determine through a consideration of the geology, topography, climate, mining activity, and evidence at ground surface, what mechanisms control subsidence .and under what circumstances it takes place. The study wan performed it two phases, the first to identify all documented incidents of subsidence in mined-out areas of the Pittsburgh coal Region; and the second, to study a particular portion of the region in detail, collecting pertinent data relative to the sites within, characterizing roil the nature of the subsidence and its economic consequences, and determining the applicability of the findings to other areas whore similar problems with the collapse of abandoned miner have been encountered.]

Jan 1, 1977

By B. C. Christensen

The contract objectives are (1) to develop safe practice guidelines which will minimize the chance of fires in underground fueling areas and (2) to develop a low-cost, reliable, automatic fire protection system for underground fueling areas. The effort described by this report covers the period from 21 June 1976 to 30 September 1977 and accomplished the following tasks: ? Preparation of Data Plan and Data Acquisition, mainly through visits to sixteen mine sites and a literature survey. ? Analysis of the accumulated data, providing design inputs for (a) evaluation of the fire problem; (b) development of safe practice guidelines; and (c) development of recommended design concepts for automatic fire protection systems. ? Preparation of safe practice guidelines for underground fueling areas. ? Preparation of recommended design concepts for automatic fire protection systems for underground fueling areas. ? Design and fabrication of fire protection system for installation at Pine Creek Mine, Bishop, California. ? Install system and perform underground fire tests at Pine Creek Mine.

Jan 1, 1977

By E. W. Greig

This paper is an account of exploration for bauxite in the Amazon Basin, Brazil, and particularly of the discovery, exploration and development by Alcan of the Trombetas deposit so a general account of the Trombetas Project has already been published in E/MJ (Anon. 1975) to which the reader is referred for details on owner-ship, infrastructure and construction as well as the proposal for mining and treating the bauxite. It is impossible to consider the Trombetas deposits in isolation. A regional account of bauxite in and around the Guyana Shield and the northern portion of the Brazilian Shield is included and it is suggested that these deposits all formed during Tertiary time under similar conditions.

Jan 1, 1977

By S. N. Chadha

INTRODUCTION The work described here refers to the Genesee River Interceptor Southeast Project. This project is a part of the Combined Sewer Overflow Abatement Program, Phase I, for the Rochester Pure Water District, Rochester, New York. Our contract required the design of a 13,200-feet long main tunnel, 14 feet finished diameter, approximately 100-120 Feet below ground; drop shafts and diversion tunnels to deliver surface flow to the main tunnel; a gate chamber whereby the main tunnel is dropped 35 feet, and provision made for connection to the future tunnel in Phase II, as well as a host of other surface structures. Cross sectional dimensions for the structures involved varied from 16 feet circular to a 20'x50' horseshoe, in a competent rock formation consisting of Lockport Dolomite and Rochester Shale. In the construction of a rock tunnel, the problems of the tunnel designers are as follows: 1. To evaluate stresses in the rock as a result of excavation. 2. Design a temporary support system to prevent any rock failure during the period of construction. Design of this temporary support system is empirical. Design loads given by empirical relations are dependent upon the rock quality and size of opening. Temporary support system may either be steel frames closely spaced along the length of tunnel and tied together, in the case of poor rock, or, an even spacing of rock bolts in the case of competent rock. 3. Design a final lining for the service loads. Service loads, in our case of a water-carrying tunnel, are hydrostatic pressure due to ground water, deadweight of lining) pressure of contained water and time dependent rock loading. The constitutive properties of the rock are extremely complex because of discontinuities, pre-existing stresses due to overburden, material symmetries and changes of initial state associated with the process of excavation. The changes of initial state may be changes of stress fields along with the consequent yield of the material or the extension of existing discontinuities.

Jan 1, 1977

By Agustín Chang

La aplicación de las técnicas de Ingenieria Industrial en las minas de Centro Min Perú son importantes para ayudar a las operaciones para mejorar la productividad y reducir los costos. Los resultados obtenidos mediante los estudios de mejoras y de medición de trabajo, permitieron elevar la eficiencia personal y la óptima utilización de los recursos de operaciones de minas. En ese sentido, el presente texto busca proveer información relacionada con la práctica industrial en las minas de CentrominPerú a los ingenierios de Minas.

Nov 1, 1976

By Juan Roldán

El presente trabajo refiere la política de creación, formación y futuro de la Escuela de Minas de Recuay en el ámbito de la minería nacional e internacional. Para ello, se revisa los fundamentos del proyecto, antecedentes, organización, formación y perfeccionamiento del personal, métodos de enseñanza y conclusiones.

Nov 1, 1976

By Jorge Vargas Fernández

El presente texto señala los fundamentos de un programa de productividad y recomienda los índices y actividades principales que puedan desarrollar las gerencias y superintendencias de las empresas para incrementar la productividad de las empresas.

Sep 1, 1976

By Lashley Harvey

El presente texto señala la importancia de un manejo adecuado de la cuenca para la producción de energía eléctrica. Para ello, es necesario revisar las vías navegables, la transportación por la costa y los ríos, el antiguo desarrollo de las vías navegables, las leyes del agua y la transformación, las mejoras de las vías navegables y el mejoramiento de zonas del puerto es costas y ríos.

Jul 1, 1976