Search Documents

Interest in the sampling of refined copper cathodes has heightened over the last ten years. This has followed the increasing importance of cathodes as the principle trading form for metallic copper. It has also been given impetus by recent trends for quality certification of manufacturing inputs, specifically the AS3900 and IS09000 series of standards.

Jan 1, 1976

By Alfred Bellows

The objective was to develop and design a remotely operated temporary roof support system that provides a safe working environment between a freshly cut coal face and the last line of permanently supported roof in which to perform roof bolting activities. This system was to take the form of a retrofit package which could be adapted to a majority of the bolters currently in service. The result is an integrated piece of hardware which will retrofit onto virtually all single boom bolters by removing the drill boom and relocating and modifying the hydraulic controls. The system is composed of three basic components: a pair of cantilevered roof supports which reach forward to the desired line of support, a mast type drill unit for drilling holes and torquing bolts, and a transverse slide assembly to carry the drill from hole to hole across the entry without relocating either the bolter or the roof support. A converted bolter not only provides a much safer operation but is projected to increase the production speed as well as reduce the manpower required to operate a section.. This improvement in productivity is shown to make the job of retrofitting a bolter cost effective in less than two months and provide a potential profit thereafter. Based on the findings presented in this report it is recommended that a proto-type be built and tested in an underground coal mine to demonstrate its effectiveness.

Jan 1, 1976

By John A. Breslin

Size distributions and concentrations of particulates emitted from diesel engine exhausts were measured with cascade impactors. Samples were taken from the exhaust of two types of engines using three types of fuel and operating under five different engine speed and load conditions. The measured mass median diameters of the diesel particulates were typically about 0.3 um. There was no significant difference in mass median diameter between engines or fuels and only a slight dependence on operating mode. Concentration measurements ranged from 14.2 to 250.9 mg/cu m, and calculated mass outputs, from 52 to 3,443 mg/min. Significant differences in mass output were found between engines, fuels, and especially between different operating modes. The quantity of clean dilution air that would be required to reduce the particulate mass concentration below the 2.0 mg/cu m respirable dust standard for coal mines was greater than the dilution air required to meet the standards for noxious gases for both engines tested.

Jan 1, 1976

By Robert J. Ramsey, N. Finkelstein, Foster J. Witthauer

First mining operations in the Tyrone District, located just north of the Burro Mountains in Grant County, New Mexico, commenced in the 1870's. A major operation was undertaken by Phelps Dodge Corporation in the early 1900's when a 2,000 ton per day underground mine was developed and a gravity concentrator was built east of the mine and across the Continental Divide. It was during this time that the picturesque Tyrone townsite was built and occupied. In 1921, however, the underground operation was closed because of high operating costs and low demand for copper. The area was drilled extensively during the 1950's and in October 1966 Phelps Dodge announced the pending development of the new Tyrone with a large open-pit mine, a modern concentrator, suitable support facilities, and a new townsite to be located between the mine and Silver City. Stripping for the pit and construction of shop and milling facilities began in 1967. By the spring of 1969, ore was being stockpiled near the primary crusher. Operation of the concentrator on a 3-shift per day basis commenced on July 17, 1969. The concentrator as initially built had one primary, two secondary, and five tertiary cone crushers, two grinding sections of six ball mills each, two flotation sections, four filters, and four tailing thickeners. 'he capacity was about 30,000 tons per day. In 1971 and 1972, the capacity was increased to 48,000 tons per day by the addition of one secondary and two tertiary crushers, one section of eight ball mills, one flotation section, two filters, and four more tailing thickeners. Centralized automatic control was built into the original and expanded facilities to the greatest extent possible, considering the state of the art at that time. Installation of additional control

Jan 1, 1976

By R. D. Call

During the past fifteen years considerable progress has been made in the technology of slope design. It is possible to design rational slope angles if suitable data on geology, hydrology, and rock properties are available. It is of course preferable to conduct a full scale slope design study, but there are those situations where a full scale study is not feasible because of time and budget constraints. In this paper we will treat two situations: (1) choosing slope angles for a preliminary feasibility study at the exploration stage; and (2) dealing with a slope failure in an operating pit. In these instances slope angles must often be chosen on the basis of available or readily obtained data. In an exploration program all too often a feasibility study is initiates just a few months prior to the decision deadline to drop the property or to exercise an expensive purchase option. If all that is available at this point are a few cross sections at odd angles showing ore and waste contacts and a dog-earred map of the surface geology there may not be time to collect and organize enough information for design of slope angles. On the other hand if during the drilling program geologic cross sections are constructed and the structural data is presented in tabular form, rational slope angles can be determined within the allotted time. Certain types of data can be collected only at specific times during a project. Two prime examples are logging fracture intensity and collecting samples for rock testing before the core is split. It is particularly disheartening to ask to see the core and to be shown a tattered cardboard box filled with plastic bags of sample pulps.

Jan 1, 1976

Sampling is an integral part of gold bullion analysis. Gold mining industries sell millions of dollars worth of gold on the basis of analyses. Biased sampling can cause a serious loss in terms of monetary value to a mining company; hence accurate sampling is of great importance. The sampling procedures for gold bullion will be described. Emphasis is given to the most reliable method of obtaining a representative sample from a gold bar. The problems associated with sample preparation will also be discussed.The sampling procedure at the Kalgoorlie Metallurgical Laboratory will be evaluated in the light of comparative results from the Australian Gold Refineries (Perth, Kalgoorlie). The most common sampling practices adopted by different gold mining companies in the Goldfields and Australian Gold Refineries, Western Australia will also be presented.

Jan 1, 1976

By Jeffrey W. Braithwaite

The laboratory characterization of the oxidation of chalcopyrite under conditions of deep solution mining is presented in this paper. A salient feature of this system is the pH buffering effect resulting from simultaneous acid producing and acid consuming oxidation reactions. The solution chemistry and related sulfur partitioning of the oxidation reactions are detailed. The contribution of temperature, acid concentration, oxygen pressure, particle size, and solution additions to the kinetics of copper extraction are presented. A mixed kinetic model was used to describe the kinetics of oxidation.

Jan 1, 1976

Reliably measure stress chan¬ges in order to assess stability of mine openings. Approach: A durable, permissible, sensor and readout system have been developed and tested. How It Works: The stress sensing element is a taut steel wire which is, vibrated at its natural frequency, If the tension on the wire is changed because of deformation of the sensor housing, the natural frequency of the wire changes. This effect is similar to decreasing or increasing the pitch of a violin string by loosening or tightening it. Because the stress sensor electrical output is a frequency signal, rather than an amplitude signal, its accuracy is unaffected by the resistance of the signal wire, or other attenuation. Signal wires can be a mile or longer without affecting accuracy. When a button is pushed on the readout box, the sensor wire is electromagnetically excited and vibrates at its natural frequency. That signal causes a readout in illuminated digits. (By referring to calibration chart and the previous reading, the user knows the change in stress.) This system is permissible. To install the sensor, a slightly oversize hole is drilled into the mine pillar. Next, a special tool is used to both position the sensor and wedge it in place. Figure 1, shows the sensor and its integral wedge and hole-fitting piece.

Jan 1, 1976

By W. D. Dietzman

This Bureau of Mines report presents a continuation of statistics pertaining to distribution of petroleum reservoirs (or fields), wells, and production by depth and producing rate classification in the United States. These statistics show the change that has occurred since results of a similar study were published by the Bureau of Mines in 1967. Data are presented in tabular form by State for the 18 principal oil-producing States and by subdivision for the two larges t oil-producing States, Texas and Louisiana, Tabular summations and graphical illustrations are presented for the Nation. The data are classified by 4-barrel-of-oil-per-day rate increments up to 36 barrels and one increment of greater than 36 barrels of oil per day and by 2,000-foot depth increments up to 8,000 feet and one depth increment of greater than 8,000 feet. The overall average producing rates for States and the Nation have been published for many years; although such rates are useful, they are very general descriptions of producibility. A breakdown of production, wells, and reservoirs by various depths and rates and by State or by State subdivision provides a more detailed description of producibility.

Jan 1, 1976

By I. S. Blair

The Mufulira smelter (1, 2,' 3, 4,) is one of three smelters situated on the Zambian Copperbelt to treat concentrates and other intermediate products produced in the area. Two mining companies, Roan Consolidated Mines Limited (RCM) and Nchanga Consolidated Copper Mines Limited (NCCM) each have 51% Zambia Government participation. RCM operates two smelters, one at its Mufulira Division and the other at its Luanshya Dl vision. NCCM operates one smelter at its Rokana Division (5). The Mufulira smelter was commissioned in 1937 with two reverberatory furnaces and four converters. The final product, blister copper, was cast from a holding furnace. In 1952 two anode furnaces and a common casting wheel were installed to feed a new and adjacent electrolytic refinery. In 1956 the smelter was extended to accommodate increasing production from the new Chibuluma mine and expansion at Mufulira mine. A third reverberatory furnace, a fifth converter and duplicate anode processing and casting facility were added. The Copperbelt smelters suffered a loss of production potential when higher ash content coals were used in reverberatory smelting furnaces from 1966 onwards. This, and the planned production increases from Mufulira and other RCM mines, indicated a smelting shortfall of 55,000 tonnes of copper a year in the combined capacity of the RCM smelters.

Jan 1, 1976

By L. W. Beckstead

The use of acid ferric sulfate solution as a lixiviant for chalcopyrite concentrates has been of little interest from a practical standpoint due to the formation of a tenacious layer of elemental sulfur which severely impedes the reaction progress. CuFeS2 + 4Fe+3 ?Cu+2 + 5Fe+2 +2s° For example, an acid ferric sulfate leach of chalcopyrite concentrate results in only 12% copper extraction in a three hour leach at 93°C. Experimental results suggest that particle size is the only controllable variable which has a significant effect on the rate of acid ferric sulfate leaching at ambient pressure. Size reduction of the concentrate prior to leaching was exam¬ined using various methods of grinding. Of the grinding methods considered, attrition grinding was found to be the most effective. Leaching of an attritor-ground product (median particle size 0.5 microns) resulted in approximately 90% copper extraction in a three hour leach at 93°C. Energy measurements suggest that the costs associated with attrition mill¬ing are not unreasonable. Evidence indicates that "activation" or stored strain energy is not responsibile for the enhanced reaction kinetics of the finely ground concentrate, but rather the experimental results can be explained simply in terms of the increased surface area due to size reduction. Leaching reaction mech¬anisms operative in the acid ferric sulfate system are discussed and the application of ultra-fine grinding technology to other systems is considered.

Jan 1, 1976

By Thomas J. Crocker, Douglas B. Uthus

Tunnel Boring Machines (TBM) have gained worldwide acceptance in the construction field and are being employed in ever increasing numbers to drive underground transit lines, drainage systems, etc. However, TBM utilization in the mining industry, and more specifically coal mining, has been very limited. This paper reviews past and present applications of TBMs to coal mining and examines the needs of the industry in an attempt to offer some insight as to what a TBM system must provide if the excavation potential demonstrated in civil works projects is to be realized in coal operations. EUROPEAN EXPERIENCE Germany The Germans recognized long ago the potential of mechanized drivage for coal mine entry development. Early in the 1960's experimental runs were made with a full-face Wohlmyer roadheader at the Westerholt Mine and trials were conducted on a roller bit armed full-face Bade roadheader. But because of problems with penetrating the various carboniferous strata occurring in changing sequence and hardness, these first attempts were soon terminated. After viewing later successes in the construction industry with improved TBMs, new attempts were initiated by the German mining industry in 1971 to mechanize drivage of their development entries. Four TBMs of two different types were placed in operation.

Jan 1, 1976

By D Maxwell Ellett

This report presents an evaluation of knowledge concerning a process used in predicting ground motion resulting from large scale conventional explosive detonations, The shots were set off in Arizona in connection with copper ore recovery activities.

Jan 1, 1976

By Roger Altman

The solubility of copper in primary spinel crystals encountered in reverberatory slag samples has been determined by electron microprobe analysis. These spinels, which ranged in composition from 22% A12O3 to pure magnetite, contained small quantities of dissolved copper (0-0.4%). Based on literature data it was estimated that the solubility limit of copper in solid magnetite is no greater than about 1% at 1200°C and about 2% at 1250°C. However, it was found that practically every spinel crystal examined contained significant amounts of matte inclusions. Further examination of converter slag revealed large quantities of irregularly shaped precipitated magnetite crystals which contained a large proportion of copper inclusions. Additional experimentation showed that the total copper content in reverberatory slag samples was greater than the sum of the estimated en- trained plus dissolved matte in the slag. This difference is believed to be significant and is due to the presence of matte inclusions in the spinel crystals. In the present reverberatory slag samples these inclusions accounted for about 1/2 of the amount of sulfide directly entrained in the slag.

Jan 1, 1976

By S. L. Aaroe

"TYRETHANE PRODUCTSTyrethane® is the family brand name which has been adopted by The W. S. Tyler Company of Canada, Limited to identify its polyurethane products. Since we have been manufacturing Woven Wire Cloth for over one hundred years and have been the innovator for most of the product improvements and developments of that industry, it is only natural that our first and primary efforts involve the use of Tyrethane® as a screening medium. The product is ideal for application in the mining industry and other operations where the rate of wear on existing media is exceptionally high.In the event that you have already had some experience with polyurethane it should be poirted cut that there are many grades of the material. The polyurethane used in Tyrethane® Products will be compounded in a variety of chemistries and different heat treatments will be used to develop best mechanical properties to handle specific applications. However Tyrethane® will not be a ""cure all"" but when it is properly applied as a screening medium it will assist by lowering the unit cost for screened materials.Prior to an explanation of the advantages of Tyrethane® let's review the conventional screening media whose applications may be considered as good candidates for replacement by Tyrethane®.1.,Woven Wire Cloth.2.,Perforated metal screens.3.,Rubber faced perforated metal screens.4.,Perforated rubber screens.5.,Cast steel screen segments and weldiments.6.,Profile wire.In most cases a Tyrethane® section is designed for a one for one replacement of the material now being used. It is rarely necessary to modify the screening equipment to enable you to install the Tyrethane® Product although it may be desirable to take some steps to improve the service life of hold down components such as Clamping Strips or Tension Members. Those parts can be encapsulated in polyurethane if necessary.To fabricate the Tyrethane® section we have three basic building blocks. They are: (1) Small molded segments having square or slotted openings, (2) Reinforcing material and (3) the raw liquid polyurethane."

Jan 1, 1976

By Edwin H. McKee

Eruption of rhyolitic ash-flow tuffs in the area of the McDermitt (Cordero) caldera began about 17.4 m.y. ago and continued for about 1.5 m.y. During this period of silicic eruptions, a circular area about 30 km in diameter collapsed to form a caldera that subsequently filled with sedimentary and volcanic rocks. 3 A total of more than 200 km of silicic rocks was erupted from the volcano. The final phase of igneous activity, about 15.5 m.y. ago, included resurgent doming and intrusion in the central part of the caldera. Three to 4 m.y. later +I2 m.y. ago), hydrothermal solutions using the northern part of the caldera ring fractures as conduits deposited cinnabar, pyrite, alunite, and other minerals in tuffaceous lake beds and volcanic rocks accumulated within the caldera. The ore-forming solutions may have been a residuum from the silicic magma or connate water or ground water heated by the still-hot resurgent magma in the central part of the caldera. The source of the mercury has not been identified. Later oxidation of the sulfide minerals and redistribution of the supergene minerals corderoite, several mercury nitro-oxychlorides, marcasite, iron, and titanium oxides in the sedimentary rocks account for most of the newly discovered ore body at Cordero.

Jan 1, 1976

By E. F. Ferrell

Gold was recovered from scrap electronic 60-40 (tin-lead) solders by drossing with aluminum or zinc at elevated temperatures. The gold, together with other metallic impurities, collected in the dross phase which could then be separated from the molten solder by skimming or filtering. Drossing upgraded the gold concentration by a factor of 10. Further upgrading was achieved by a combination of steps including an oxidation roast and either a combined cyanidation-amalgamation treatment or an aqua regia leach. The gold was then recovered in highly concentrated form from the aqua regia or cyanide solutions by cementation and from the amalgam by volatilization or dissolution of the mercury. The solder was purified by reaction with NaOH to remove dissolved aluminum or with SnCl2 to remove dissolved zinc.

Jan 1, 1976

By Herbert F. Nyberg

The Black River Falls Mine is owned and operated by Jackson County Iron Company, a wholly owned subsidiary of Inland Steel Company. It is located in vest central Wisconsin, seven miles east of the city of Black River Falls. This is the first taconite plant in the state of Wisconsin. Iron mining started in this area in 1856 but soon failed due to the low grade ore and crude methods of mining and transportation. Inland Steel Company acquired the property in 1939. Some drilling and test work was done in 1940, but the economics of developing the property at that time were not favolable. Improved methods of concentrating and pelletizing in the 1960's made it possible to build the present plant. Due to the limited ore reserve of 45,000,000 tons with expected recovery of 33% it was necessary to limit the capacity of the operation to 750,000 TPY with a life of 20 years. There was some concern about an operation of such limited capacity. A million ton operation was considered the minimum size plant for a profitable operation.

Jan 1, 1976

Although the Stamler feeder/breaker has been used for coal crushing in underground mines for many years, it has only recently been applied to other crushing operations. Two companies presently using Stamler feeder/breakers for rock crushing were contacted regarding their experiences with the units in actual field use. In both cases information was obtained directly from the individuals responsible for field operation and maintenance of the units. White Pine Copper Co. has been using Stamler feeder/breakers for over two years to crush copper ore. They now have fourteen 450-ton-per-hour units on line. The ore has a compressive strength of from 18,000 to 28,000 psi and is extremely abrasive. Maintenance is performed on a tonnage basis. The breaker shaft is replaced every 250,000 tons (requiring about 4 hrs) and picks are replaced about every 1500 tons by the operator (requiring about 2 min per pick). Very little unscheduled maintenance has been required. Crushing costs are fairly high (estimated at 13 to 15t per ton including maintenance and operation) because of tale extreme abrasiveness of the material. A new Stamler feeder/breaker with Ultramet wear surfaces was put or line in June 1976. Ultramet was found to increase the life of belt transfer station surfaces by up to 400 percent and it is hoped that it will do the same for the feeder/breaker. At this time it is still too early to evaluate the performance of the Ultramet unit. If it does improve abrasion resistance, crushing costs could be greatly reduced. White Pine is very pleased with the units and the service provided by Stamler.

Jan 1, 1976

By H. B. Treweek, V. R. Degner

Current mineral industry trends toward handling the high tonnages of lower grade ore and tailings retreat lead to a continuing need for large volume flotation cells. The benefits which accompany the larger cell flotation circuit include reduced capital cost, less mill floor space, reduced operational complexity, and less maintenance, provided the metallurgical performance and solids suspension capability of the cell are not compromised. This study reviews development considerations pertinent to large mechanical air induction type flotation cells from the standpoint of cell internal hydrodynamic characteristics and metallurgical performance. While the importance of process related factors such as chemical usage, pH control, solids size and loading, and circuit arrangement cannot be denied, this study will emphasize the relationship of cell size (volume), mechanism geometry (impeller diameter), and mechanism operating conditions (rotor speed and submergence), to air transfer, liquid circulation, liquid "rise velocity" and mechanism power draw. Specific hydraulic performance maps for large capacity 300 and 500 cu ft flotation cells will be reviewed in terms of the relationship between the operational variables and the air and liquid flow conditions within the cell. Metallurgical results, obtained under plant operating conditions for 300 and 500 cu ft cells, are included to illustrate the metallurgical performance similarity of flotation cells which follow hydrodynamic scale-up criteria set forth in this investigation.

Jan 1, 1976